Sharp XR-50S Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Sharp XR-50S (79 pagina's) in de categorie Beamer. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/79

Introduction Easy Start Setup Connections Basic
Operation
Useful
Features Appendix
OPERATION MANUAL
MUTIMEDIA PROJECTOR
MODEL
XR-55X
XR-50S

ii
IMPORTANT
• For your assistance in reporting the loss
or theft of your Projector, please record
the Model and Serial Number located on
the bottom of the projector and retain this
information.
• Before recycling the packag ing, please
ensure that you have checked the con-
tents of the carton thoroughly against the
list of “Supplied accessories” on page .11
Model No.:
Serial No.:

iii
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fi tted with a non-rewireable (moulded) plug incorporating
a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse
marked or and of the same rating as above, which is also indicated on the pin face
of the plug, must be used.
Always refi t the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fi tted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fi t an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-
ately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket
outlet, as a serious electric shock may occur.
To fi t an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this apparatus may not correspond with
the coloured markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol or coloured green
or green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked
with the letter N or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked
with the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
E.U. ONLY

iv
The supplied CD-ROM contains operation instructions in English, German, French, Spanish,
Italian, Dutch, Swedish, Portuguese, Chinese, Korean and Arabic. Carefully read through the
operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,
Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch, Koreanisch
und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors
sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français,
espagnol, italien, néerlandais, suédois, portugais, chinois, coréen et arabe. Veuillez lire at-
tentivement ces instructions avant de faire fonctionner le projecteur.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés,
español, italiano, holandés, sueco, portugués, chino, coreano y árabe. Lea cuidadosamente
las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo,
italiano, olandese, svedese, portoghese, cinese, coreano e arabo. Leggere attentamente le
istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans,
Italiaans, Nederlands, Zweeds, Portugees, Chinees, Koreaans en Arabisch. Lees de
handleiding zorgvuldig door voor u de projector in gebruik neemt.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska,
spanska, italienska, holländska, svenska, portugisiska, kinesiska, koreanska och arabiska.
Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês,
Espanhol, Italiano, Holandês, Sueco, Português, Chinês, Coreano e Árabe. Leia
cuidadosamente todas as instruções de operação antes de operar o projetor.

1
Introduction
Before using the projector, please read this operation manual carefully.
Introduction
ENGLISH
There are two important reasons for prompt warranty registration of your new
SHARP Projec tor, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefi t of the parts,
service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notifi cation of inspection,
modifi cation, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANT Y” CLAUSE. U.S.A. ONLY
WARNING: FCC Regulations state that any unauthorized changes or modifi cations
to this equipment not expressly approved by the manufacturer could
void the user's authority to operate this equip ment.
U.S.A. ONLY
The lightning fl ash with arrowhead sym-
bol, within an equilateral triangle, is in-
tended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product's enclosure that may
be of suffi cient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the pres-
ence of important operating and main-
tenance (servicing) instructions in the
literature accompanying the product.
See bottom of projector.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
WARNING: To reduce the risk of fi re or electric shock, do not
expose this product to rain or mois ture.
WARNING: High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small
amount of mercury. Disposal of these materials may be regulated due
to environmental considerations. For disposal or recycling information,
please contact your local authorities, the Electronics Industries Alliance:
www.eiae.org, the lamp recycling organization www.lamprecycle.org, or
Sharp at 1-800-BE-SHARP.
U.S.A. ONLY

2
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the operation manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help. U.S.A. ONLY
Caution Concerning Lamp Replacement
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
Caution
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burns or injury.
Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to
fully cool before removing the lamp unit.
Do not touch the glass surface of the lamp unit or the inside of the projector.
Do not loosen other screws except for the lamp unit cover and lamp unit.
Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the lamp to become damaged or explode.
Carefully change the lamp by following the instructions described on pages . 56 to 58
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
■
■
■
■
•
•
•
•
•
■
Declaration of conformity
SHARP PROJECTOR, MODEL XR-55X/XR-50S
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 074 -95 1163
TEL: 1-800-BE-SHARP (1-800-237-4277) U.S.A. ONLY

3
Introduction
How to Read this Operation Manual
The specifi cations are slightly different, depending on the model. However, you can connect
and operate all models in the same manner.
In this operation manual, the illustration and the screen display are simplifi ed for explanation, and
may differ slightly from the actual display. The examples used throughout this manual are based
on the XR-55X model.
38
Adjustm ent but tons
( /P R/O Q/ )
ENTER button
RETURN button
Press RETURN to retur n
to the pre vious screen
when the menu is
displayed.
•
MENU button
Adjustm ent but tons (P R/ /O Q/ )
MENU button
ENTER button
Menu Selections (Quick Start Menu)
This o peration can a lso be pe rfor med by using the buttons on the projector.•
1 Press MENU.
The “Quick Start Menu” screen for th e
selected Input mode is displayed.
2 Press P R or to select the
desired item, then press ENTER.
3 Press P R/ /O Q/ to adjust the
item selected, then press
ENTER.
Info
To display the advanced settings and
adjus tments, select “G o To Compl ete Menu”.
Press ENTER to dis play the Complete Menu
screen.
If you do not want to disp lay the Quick Sta rt
Menu, set “Go To Complete Menu” - “PRJ-ADJ2”
- “Quick Star t Menu” to “Off ”. (See pa ge 51.)
•
•
•
1
2
3
Example
SEL./ADJ. ENT ER END
Input Search Start
Resolution
Resize
0
ECO+Quiet
Language
Keystone
Information
1024×768
Normal
English
Off
Quick Start Menu
Go To Complete Menu…
Using the Menu Screen
Select from the Quick Start Menu, which is a collection of the most frequently used
functions, or the Complete Menu, which enables advanced settings and adjustments.
Buttons used in
this operation
On-screen
display
Button used in
this step
Info
.........Indicates safeguards for using the projector.
Note
....... Indicates additional information for setting up and operating the
projector.
For Future Reference
Maintenance
P. 53
Troubleshooting
PP. 67 and 68
Index
P. 72
■
•

4
Contents
Preparing
Introduction
How to Read this Operation Manual ......3
Contents .................................................4
IMPORTANT SAFEGUARDS ..................6
How to Access the PDF Operation
Manuals ..............................................10
Accessories ..........................................11
Part Names and Functions ...................12
Front View .............................................. 12
Top View ................................................ 12
Rear View (Terminals) .............................. 13
Inserting the Batteries ............................. 15
Usable Range ......................................... 15
Easy Start
Easy Start .............................................16
Setup and Projection .............................. 16
Setup
Setting Up the Projector .......................18
Setting Up the Projector ......................... 18
Standard Setup (Front Projection) ........... 18
Screen Size and Projection Distance ...... 19
Projection (PRJ) Mode ............................ 20
Ceiling-Mount Setup ............................... 20
Connections
Connecting the Projector to
Other Equipment ................................21
Controlling the Projector by
a Computer ........................................24
Connecting the Power Cord .................24
Displaying the Black Screen and
Turning Off the Sound Temporarily ....... 29
Resize Mode .......................................... 30
Useful Features
Operating with the Remote Control......32
Displaying and Setting the
Break Timer ......................................... 32
Displaying the Pointer ............................. 32
Using the Spot Function ......................... 32
Switching the Eco+Quiet Mode .............. 32
Auto Sync (Auto Sync Adjustment) ......... 33
Freezing a Moving Image ........................ 33
Selecting the Picture Mode ..................... 33
Displaying an Enlarged Portion of
an Image ............................................. 33
Using the Remote Control as the
Wireless Computer Mouse ................... 34
Menu Items ...........................................35
Using the Menu Screen ........................38
Menu Selections (Quick Start Menu) .........38
Quick Start Menu .................................... 39
Menu Selections (Complete Menu) .......... 39
Picture Adjustment (“Picture” Menu) ....41
Selecting the Picture Mode ..................... 41
Adjusting the Image ................................ 42
Adjusting the Color Temperature ............. 42
Adjusting the Colors ............................... 42
Selecting the Film Mode ......................... 43
Reducing Image Noise (DNR) ................. 43
Eco+Quiet .............................................. 43
Signal Adjustment (“SIG-ADJ” Menu) ..44
Adjusting the Computer Image ............... 44
Resolution Setting .................................. 44
Signal Type Setting ................................. 44
Setting the Video System ....................... 45
Setting the Video Setup .......................... 45
Checking the Input Signal ....................... 45
Adjusting the Projected Image
(“SCR - ADJ” Menu) ...........................46
Setting the Resize Mode ......................... 46
Adjusting the Image Position .................. 46
Keystone Correction ............................... 46
Setting the Overscan .............................. 47
Setting the On-screen Display ................ 47
Closed Caption ...................................... 47
Selecting the Background Image ............ 48
Selecting the Setup Guide ...................... 48
Reversing/Inverting Projected Images ..... 48
Selecting the Wall Color .......................... 48
Selecting the On-screen Display Language
... 48
Using
Basic Operation
Turning the Projector On/Off ................25
Turning the Projector On ......................... 25
Turning the Power Off (Putting the
Projector into Standby Mode) .............. 25
Image Projection ..................................26
About the Setup Guide ........................... 26
Adjusting the Projected Image ................ 26
Correcting Trapezoidal Distortion ............ 28
Switching the Input Mode ....................... 29
Adjusting the Volume .............................. 29

5
Introduction
Adjusting the Projector Function
(“PRJ-ADJ1/2” Menu) ........................49
Auto Sync (Auto Sync Adjustment) ......... 49
Auto Power Off Function ........................ 49
Auto Restart Function ............................. 49
Speaker Setting ...................................... 49
Selecting the Transmission Speed
(RS-232C) ........................................... 49
Fan Mode Setting ................................... 50
System Lock Function ............................ 50
Keylock Function .................................... 51
Selecting the Quick Start Menu .............. 51
Setting the FUNCTION Button Operation
.. 51
STANDBY Mode ..................................... 52
DLP® LinkTM ............................................ 52
DLP® LinkTM Invert .................................. 52
Returning to the Default Settings ............ 52
Checking the Lamp Life Status ............... 52
Appendix
Maintenance .........................................53
Maintenance Indicators ........................54
Regarding the Lamp .............................56
Lamp ...................................................... 56
Caution Concerning the Lamp ................ 56
Replacing the Lamp ............................... 56
Removing and Installing the
Lamp Unit ............................................ 57
Resetting the Lamp Timer ...................... 58
Connecting Pin Assignments ...............59
RS-232C Specifi cations and
Commands ........................................61
Computer Compatibility Chart .............66
Troubleshooting ....................................67
For SHARP Assistance .........................68
Specifi cations .......................................70
Dimensions ...........................................71
Index .....................................................72
Reference

6
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this
product and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its
installation, use and servicing.
1. Read Instructions
All the safety and operating instructions
should be read before the product is
operated.
2. Retain Instructions
The safety and operating instructions
should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should
be followed.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for
example, near a bath tub, wash bowl, kitchen
sink, or laundry tub; in a wet basement; or
near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer's instructions, and should use a
mounting accessory recom mended by the
manufacturer.
9. Transportation
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart
combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided
for ventilation to ensure reliable operation of
the product and to protect it from overheating,
and these openings must not be blocked or
covered. The open ings should never be
blocked by placing the product on a bed, sofa,
rug, or other similar surface. This prod uct
should not be placed in a built-in installation
such as a book case or rack unless proper
ventilation is provided or the manufacturer's
in struc tions have been adhered to.
11. Power Sources
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the
type of power supply to your home, consult
your product dealer or local power
com pany. For products intended to operate
from battery power, or other sources, refer
to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the
following types of plugs. If the plug should
fail to fi t into the power outlet, please contact
your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug
with a grounding terminal.
This plug will only fi t into a grounding
type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so
that they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords
at plugs, convenience receptacles, and the
point where they exit from the product.
14. Lightning
For added protection for this product during
a lightning storm, or when it is left
unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the cable system. This will
pre vent damage to the product due to
lightning and power-line surges.

7
Introduction
15. Overloading
Do not overload wall outlets, extension cords,
or integral convenience receptacles as this
can result in a risk of fi re or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fi re or electric shock.
Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product
yourself as opening or removing covers
may expose you to dan ger ous voltage or
other hazards. Refer all servicing to
qualifi ed service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet
and refer servicing to qualifi ed service
person nel under the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects
have fallen into the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those con trols that are
covered by the operating instructions,
as an improper adjustment of other
controls may result in damage and will
often require extensive work by a
qualifi ed technician to restore the
product to normal operation.
e. If the product has been dropped or
damaged in any way.
f. When the product exhibits a distinct
change in performance, this indicates a
need for service.
19. Replacement Parts
When replacement parts are required, be
sure the service technician has used
replace ment parts specifi ed by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result in
fi re, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs
to this product, ask the service technician
to per form safety checks to determine that
the product is in proper operating
condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall
or ceiling only as recommended by the
manufacturer.
22. Heat
This product should be situated away from
heat sources such as radiators, heat
registers, stoves, or other products
(including amplifi ers) that produce heat.
DLP® and the DLP logo are registered trademarks of Texas Instruments and
BrilliantColor
TM and DLP® LinkTM are trademarks of Texas Instruments.
Microsoft® and Windows®
are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
Adobe® Reader® is a trademark of Adobe Systems Incorporated.
Macintosh®
is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
All other company or product names are trademarks or registered trademarks of their
respective companies.
Some IC chips in this product include confi dential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
•
•
•
•
•
•
•

8
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp
ruptures. In case of lamp rupture, contact
your nearest Sharp Authorized Projector
Dealer or Service Center
for replacement.
See “Regarding the Lamp”
on page 56.
Caution concerning the setup of the
projector
For minimal servicing and to maintain high
image quality, SHARP recommends that
this projector be installed in an area free
from humidity, dust and cigarette smoke.
When the projector is subjected to these
environments, the vents and lens must be
cleaned more often. As long as the
projector is regularly cleaned, use in these
environments will not reduce the overall
operation life of the unit. Internal cleaning
should only be performed by a Sharp
Authorized Projector Dealer or Service
Center.
Rest your eyes occasionally.
Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Do not set up the projector in places
exposed to direct sunlight or bright light.
Position the screen so that it is not in direct
sunlight or room light. Light falling directly
on the screen washes out the colors,
making viewing diffi cult. Close the curtains
and dim the lights when setting up the
screen in a sunny or bright room.
Caution regarding placing of the projector
Place the projector on a level site within the
adjustment range (9 degrees) of the
adjustment foot.
After the projector is purchased, a faint
smell from the vent may appear when the
power is fi rst turned on. This is normal and
is not a malfunction. It will disappear after
the projector is used for a while.
■
■
■
■
■
■
When using the projector in high-
altitude areas such as mountains (at
altitudes of approximately 1,500
meters (4,900 feet) or more)
When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to
“High”. Neglecting this can affect the
longevity of the optical system.
Use the projector at altitudes of 2,300
meters (7,500 feet) or less.
Warning about placing the projector in
a high position
When placing the projector in a high
position, make certain it is carefully secure
to avoid personal injury caused by the
projector falling down.
Do not subject the projector to hard
impact and/or vibration.
Protect the lens so as not to hit or damage
the surface of the lens.
Avoid locations with extremes of
temperature.
The operating temperature of the projector
is from 41°F to 95°F (+5°C to +35°C).
The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
Allow at least 11 13/16 inches (30 cm) of
space between the exhaust vent and the
nearest wall or obstruction.
Ensure that the intake vent and the exhaust
vent are not obstructed.
If the cooling fan becomes obstructed, a
protection circuit will automatically put the
projector into Standby mode to prevent
overheat damage. This does not indicate a
malfunction. (See pages 54 and 55.)
Remove the projector power cord from the
wall outlet and wait at least 10 minutes.
Place the projector where the intake and
exhaust vents are not blocked, plug the
power cord back in and turn on the
projector. This will return the projector to
the normal operating condition.
■
■
■
■
■
■
■
■
■

9
Introduction
Caution regarding usage of the projector
If you are not to use the projector for a long
time or before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other
cables connected to it.
Do not carry the projector by holding the
lens.
When storing the projector, ensure that you
close the lens shutter.
Do not expose the projector to direct
sunlight or place next to heat sources.
Doing so may affect the cabinet color or
cause deformation of the plastic cover.
Other connected equipment
When connecting a computer or other
audio-visual equipment to the projector,
make the connections AFTER unplugging
the power cord of the projector from the
AC outlet and turning off the equipment to
be connected.
Please read the operation manuals of the
projector and the equipment to be
connected for instructions on how to make
the connections.
■
■
■
■
■
■
Using the projector in other countries
The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
If the temperature inside the projector
increases, due to blockage of the air vents,
or the setting location, the temperature
warning indicator will blink. And if the
temperature keeps on rising, “ ” will
illuminate in the lower left corner of the
picture with the temperature warning
indicator blinking. If this state continues,
the lamp will turn off, the cooling fan will
run and then the projector will enter
Standby mode. Refer to “Maintenance
Indicators” on pages 54 and for details.55
Info
The cooling fan regulates the internal
temperature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in the
fan speed. This does not indicate malfunction.
■
■
•
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this
license (“Fonts”) and associated documentation fi les (the “Font Software”), to reproduce and distribute the
Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell
copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so, subject
to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one
or more of the Font Software typefaces.
The Font Software may be modifi ed, altered, or added to, and in particular the designs of glyphs or
characters in the Fonts may be modifi ed and additional glyphs or characters may be added to the Fonts,
only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been
modifi ed and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font
Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER
RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN
THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall
not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software
without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further
information, contact: fonts at gnome dot org.

10
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM. To
utilize these manuals, you need to install Adobe® Reader® on your computer
(Windows® or Macintosh®).
Please download Adobe® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals for Windows® (For Macintosh®, skip step 2).
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
4 Double click the “MANUALS” folder.
5 Double click the model (name of the folder) that you want to view.
6 Double click the language (name of the folder) that you want to view.
7 Double click the pdf fi le to access the projector manuals.
If the desired pdf fi le cannot be opened by double clicking the mouse, start Adobe
® Reader® fi rst,
then specify the desired fi le using the “File”, “Open” menu.
•
Note

11
Introduction
Accessories
Supplied accessories
Power cord*
For U.S. and
Canada, etc.
(6' (1.8 m))
<QACCDA007WJPZ>
For Europe,
except U.K.
(6' (1.8 m))
<QACCVA011WJPZ>
For U.K. and
Singapore
(6' (1.8 m))
<QACCBA036WJPZ>
For Australia, New
Zealand and Oceania
(6' (1.8 m))
<QACCLA018WJPZ>
(1) (2) (3) (4)
* Which power cords are supplied along with your projector depends on the region. Use the power
cord that corresponds to the wall outlet in your country.
Operation manuals (this manual <TINS-E335WJZZ>, Operation Manual for Stereoscopic 3D
Projection <TINZ-E500WJZZ> and CD-ROM <UDSKAA121WJZZ>)
•
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
RGB cable
(10' (3.0 m))
<QCNWGA086WJPZ>
for XR-55X
<RRMCGA837WJSA>
Remote control
for XR-50S
<RRMCGA818WJSA>
Codes in “< >” are Replacement parts codes.•
Note
Optional accessories
■ Lamp unit
■ Ceiling-mount adaptor
■ Ceiling-mount bracket
■ Ceiling-mount unit
■ Ceiling-mount extension tube
■ Remote receiver
■ 3 RCA to mini D-sub 15 pin cable (10 n (3.0 m))
■
DIN-D-sub RS-232C adaptor (5 57
/64 (15 cm))nn
AN-D350LP
AN-60KT
AN-XRCM30 (for U.S.A. only)
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XRCM30>
(for U.S.A. only)
AN-MR2
AN-C3CP2
AN-A1RS
Some of the optional accessories may not be available depending on the region. Please check with
your nearest Sharp Authorized Projector Dealer or Service Center.
•
Note

12
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the
topic is explained.
2
4 5 6
3
7 8 9
1
11
12
13
15
14
10
16
17
18
19
2
4 5 6
3
7 8 9
1
11
12
13
15
14
10
16
17
18
19
Front View
1 Exhaust vent 53
2 Zoom ring 27
For enlarging/reducing the picture.
3 Focus ring 26
For adjusting the focus.
4 Lens shutter 25, 29
5 HEIGHT ADJUST lever 27
6 Adjustment foot 27
7 Remote control sensor 15
8 Speaker 49
9 Intake vent 53
Top View
10 Temperature warning indicator 54
11 Lamp indicator 54
12 Power indicator 54
13 STANDBY/ON button 25
For turning the power on and putting the
projector into Standby mode.
14 INPUT buttons ( / ) P R 29
For switching Input mode.
15 AUTO SYNC button 33
For automatically adjusting images when
connected to a computer.
16 Adjustment buttons (P R/ /O Q/ ) 38
For selecting menu items.
17 ENTER button 38
For setting items selected or adjusted on
the menu.
18 MENU button 38
For displaying adjustment and setting
screens.
19 VOL (Volume) buttons (–O Q/ +) 29
For adjusting the speaker sound level.

13
Introduction
12
7
11109
1 2 3 4 5 6
8
12
7
11109
1 2 3 4 5 6
8
Rear View (Terminals)
1 RS-232C terminal 24
Terminal for controlling the projector using a
computer.
2 USB terminal 34
Terminal connecting with the USB terminal
on the computer for using the supplied
remote control as the computer mouse.
3 MONITOR OUT terminal 23
(Output terminal for computer RGB and
component signals.)
Terminal for connecting a monitor.
4 AUDIO 1 input terminal 23
5 COMPUTER/COMPONENT input
terminal 21, 22
Terminal for computer RGB and component
signals.
6 S-VIDEO input terminal 22
Terminal for connecting video equipment
with an S-video terminal.
7 VIDEO input terminal 22
Terminal for connecting video equipment.
8 AUDIO 2 input terminal 23
9 AC socket 24
Connect the supplied power cord.
10 Kensington Security Standard
connector
11 Rear adjustment foot 27
12 Security bar
Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for
instructions on how to use it to secure the projector.
•

14
2
3
4
7
8
10
6
1
9
11
12
13
14
15
16
18
20
21
22
23
19
17
5
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the
topic is explained.
1 ON button 25
For turning the power on.
2 STANDBY button 25
For putting the projector into the Standby
mode.
3 INPUT buttons ( / ) 29
For switching Input mode.
4 BREAK TIMER button 32
For displaying the break time.
5 MAGNIFY buttons 33
For enlarging/reducing part of the image.
6 PAGE UP/PAGE DOWN buttons 34
Same as the [Page Up] and [Page Down]
keys on a computer keyboard, when with
the USB connection (using a USB cable or
the optional remote receiver).
7 POINTER button 32
For displaying the pointer.
8
MOUSE/Adjustment buttons (P R/ /O Q/ )
34, 38
For moving the computer cursor when with the
USB connection (using a USB cable or the
optional remote receiver).
For selecting and adjusting menu items.
•
•
9 L-CLICK/EFFECT button 34, 32
For the Left click when with the USB
connection (using a USB cable or the optional
remote receiver).
For changing the pointer or spot area.
10 KEYSTONE button 28
For entering the Keystone Correction
mode.
11 AUTO SYNC button 33, 49
For automatically adjusting images when
connected to a computer.
12 FUNCTION button 51
For operating and executing a function
assigned to “FUNCTION Button”.
13 ECO+QUIET button 32
For lowering the noise of the cooling fan
and extending the lamp life.
14 FREEZE button 33
For freezing images.
15 AV MUTE button 29
For temporarily displaying a black screen
and turning off the sound.
16 VOL +/– (Volume) buttons 29
For adjusting the speaker sound level.
17 SPOT button 32
For displaying the spotlight.
18 EN TER bu tto n 38
For setting items selected or adjusted on
the menu.
19 R- CLICK/RE TURN button 34, 38
For the Right click when with the USB
connection (using a USB cable or the optional
remote receiver).
For returning to the previous menu screen
during menu operations.
20 MENU button 38
For displaying adjustment and setting
screens.
21 RESIZE button 30
For switching the picture size (NORMAL,
16:9, etc.).
22 3D MODE button (XR-55X only)
See the Operation Manual for Stereoscopic
3D Projection provided separately.
23 PICTURE MODE button 33
For selecting the appropriate picture.
•
•
•
•

15
Introduction
Inserting the Batteries
1 Pull down the tab on the cover and remove the
cover towards the direction of the arrow.
2 Insert the batteries.
Insert the batteries making sure the polarities correctly match
the m n and marks inside the battery compartment.
3 Insert the lower tab of the cover into the opening,
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode.
Please follow the precautions below
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
Insert the batteries making sure the polarities correctly match the and m n marks inside the battery
compartment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fl uid from leaked batteries is harmful to skin, therefore ensure you wipe them fi rst and then
remove them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
•
•
•
•
•
•
•
•
•
1
2
3
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
The signal from the remote control can be
refl ected off a screen for easy operation.
However, the effective distance of the signal
may differ depending on the screen material.
•
Note
When using the remote control
Ensure that you do not drop it or expose it to
moisture or high temperature.
The remote control may malfunction under a
fl uorescent lamp. In this case, move the
projector away from the fl uorescent lamp.
•
•
Remote control sensor
Remote control signal
transmitters
Remote control
33 n (10 m)
30°
30°
Remote control sensor
Remote control signal
transmitters
Remote control
33 n (10 m)
30°
30°

16
Easy Start
This section shows the basic operation (projector connecting with the computer). For details,
see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
STANDBY button
8
KEYSTONE button
5
3ON button
6INPUT buttons
5Adjustment
buttons
(P R/ /O Q/ )
6
INPUT buttons
6
STANDBY/ON
button
3
8
Focus ring
4
HEIGHT
ADJUST lever
4
Zoom ring
4
6O Q/ buttons
1. Place the projector facing a wall or a screen _P. 18
When connecting equipment other than a computer, see pages
22 and .23
2. Connect the projector to the computer and plug the power
cord into the AC socket of the projector
_PP. 21, 24
On the projector On the remote control
3. Open the lens shutter fully and then turn the projector on
_P. 25

17
Easy Start
1 After the projector turns on, the Setup Guide appears.
(When “Setup Guide” is set to “On”. See page 48.)
2
Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.
3 After adjusting the focus, height (angle) and picture size, press ENTER to fi nish the
Setup Guide.
4. Adjust the projected image with the Setup Guide
_P. 26
Correcting trapezoidal distortion using Keystone Correction.
On the remote control
Shrinks
upper side.
Shrinks
lower side.
5. Correct trapezoidal distortion
_P. 28
Press INPUT INPUT P R/ to display the INPUT list. Use P R/ to select the Input mode,
and use O Q/ to select the audio input terminal.
On the
projector
On the remote
control
INPUT list
COMPUTER
INPUT Audio
S-VIDEO
S
VIDEO
V
On the
projector
On the remote
control
6. Select the Input mode
_P. 29
7. Turn the computer on
_P. 25
8. Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press
the button again while the confi rmation message is displayed to put the projector into
Standby mode.
On-screen display
On the
projector
On the remote
control

18
Setting Up the Projector
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector's
feet fl at and level. Doing so will eliminate the need for Keystone correction and provide the best
image quality. (See page 28.)
Standard Setup (Front Projection)
Place the projector at the required distance
from the screen according to the desired
picture size. (See page 19.)
300" (762 cm)
200" (508 cm)
100" (254 cm)
40" (102 cm)
34'0
"
–41'3"
(10.4 m – 12.6 m)
22'8
"–
27'6
"
(6.9 m – 8.4 m)
11'4
"–
13'9
"
(3.5 m – 4.2 m)
4'6
"–
5'6
"
(1.4 m – 1.7 m)
240" 180"×
(610 cm-457 cm)
160"
×
120"
(406 cm-305 cm)
80"
×
60"
(203 cm-152 cm)
32"
×
24"
(81 cm-61 cm)
Picture Size
Projection
Distance
Indication of the Projection Image Size and Projection Distance
Example: 4:3 Signal Input (Normal Mode)
■

19
Setup
Screen Size and Projection Distance
Screen
Lens center
H
L
4:3 Signal Input (Normal Mode)
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
Diagonal [χ] Width Height Minimum [L1] Maximum [L2]
300"(762 cm) 610 cm (240") 457 cm (180") 10.4 m (34' 0") 12.6 m (41' 3") 18 cm
(7 1
/4")
250"(635 cm) 508 cm (200") 381 cm (150") 8.6 m (28' 4") 10.5 m (34' 4") 15 cm
(6 1
/32")
200"(508 cm) 406 cm (160") 305 cm (120") 6.9 m (22' 8") 8.4 m (27' 6") 12 cm
(4 53
/64")
150"(381 cm) 305 cm (120") 229 cm (90") 5.2 m (17
' 0") 6.3 m (20' 7") 9 cm
(3 5
/8")
120"(305 cm) 244 cm (96") 183 cm (72
") 4.1 m (13
' 7") 5.0 m (16' 6") 7 cm
(2 57
/64")
100"(254 cm) 203 cm (80") 152 cm (60
") 3.5 m (11
' 4") 4.2 m (13' 9") 6 cm
(2 27
/64")
80"(203 cm) 163 cm (64") 122 cm (48
") 2.8 m (9
' 1") 3.3 m (11
' 0") 5 cm
(1 15/16")
70"(178 cm) 142 cm (56") 107 cm (42
") 2.4 m (7
' 11") 2.9 m (9' 7") 4 cm
(1 11/16")
60"(152 cm) 122 cm (48") 91 cm (36
") 2.1 m (6
' 10") 2.5 m (8' 3") 4 cm
(1 29
/64")
40"(102 cm) 81 cm (32") 61 cm (24
") 1.4 m (4
' 6") 1.7 m (5
' 6") 2 cm
(31/32
")
16:9 Signal Input (16:9 Mode)
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
Adjustable range of
image position [S]
Diagonal [χ] Width Height Minimum [L1] Maximum [L2]
300'' (762 cm) 664 cm (261'') 374 cm (147'') 11.3 m (37' 1") 13.7 m (44
' 11 ") 82 cm
(32
13 /32")
±62 cm
(±24 33/64")
250'' (635 cm) 553 cm (218'') 311 cm (123'') 9.4 m (30' 11") 11.4 m (37
' 5") 69 cm (27 "
) ±52 cm
(±20 27
/64")
200'' (508 cm) 443 cm (174'') 249 cm (98'' ) 7.5 m (24
' 9") 9.1 m (29
' 11 ") 55 cm
(21 39 /64")
±42 cm
(±16 11 /
32 ")
150'' (381 cm) 332 cm (131'') 187 cm (74'' ) 5.6 m (18
' 6") 6.8 m (22
' 5") 41 cm
(16 13/64")
±31 cm
(±12 1/4
")
120'' (305 cm) 266 cm (105'') 149 cm (59'' ) 4.5 m (14
' 10") 5.5 m (18
' 0") 33 cm
(12 31/32 ")
±25 cm
(±9 13/16
")
100'' (254 cm) 221 cm (87'' ) 125 cm (49
'' ) 3.8 m (12
' 4") 4.6 m (15
' 0") 27 cm
(10 51/64 ")
±21 cm
(±8 11/64")
80'' (203 cm) 177 cm (70'' ) 100 cm (39
'' ) 3.0 m (9
' 11") 3.6 m (12
' 0") 22 cm
(8 41/64
")
±17 cm
(±6 17/32")
60'' (152 cm) 133 cm (52'' ) 75 cm (29
'' ) 2.3 m (7
' 5") 2.7 m (9
' 0") 16 cm
(6 31
/64
")
±12 cm
(±4 29
/32")
40'' (102 cm) 89 cm (35'' ) 50 cm (20
'' ) 1.5 m (4
' 11") 1.8 m (6' 0") 11 cm
(4 21
/64
")
±8 cm
(±3 17/64
")
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
4:3 Signal 16:9 Signal
[m/cm] [Feet/inches] [m/cm] [Feet/inches]
L1: Minimum projection distance (m/ft) 0.03457
χ
0.03457
χ
/ 0.3048 0.03766
χ
0.03766
χ
/ 0.3048
L2: Maximum projection distance (m/ft) 0.04187
χ
0.04187
χ
/ 0.3048 0.04562
χ
0.04562
χ
/ 0.3048
H:
Distance from the lens center to the bottom of the image (cm/in)
0.06134
χ
0.06134
χ
/ 2.54 0.27437
χ
0.27437
χ
/ 2.54
S:
Adjustable range of image position (cm/in) See page .46
— — ±0.20754
χ
±0.20754
χ
/ 2.54
χ : Picture diagonal size : 40
''
-300
''
Allow a margin of error in the values in the diagrams above.•
Note

20
Setting Up the Projector (Continued)
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the
mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-
ADJ” menu. See page 48.)
Table mounted, front projection
[Menu item ➞ “Front”]
Table mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Rear”]
■
■
Ceiling mounted, front projection
[Menu item ➞“Ceiling + Front”]
Ceiling mounted, rear projection
(with a translucent screen)
[Menu item ➞“Ceiling + Rear”]
■
■
a
Ceiling-Mount Setup
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this
installation. Before mounting the projector, contact your nearest Sharp Authorized Projector
Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold
separately).

21
Connections
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet
and turn off the equipment to be connected. After making all connections, turn on the projector
and then the other pieces of equipment. When connecting a computer, ensure that it is the last
equipment to be turned on after all the connections are made.
For more details of connection and cables, refer to the operation manual of the connecting equipment.
You may need other cables or connectors not listed below.
Terminals on the Projector
Equipment
Terminal on
connected equipment
Cable Terminal on the
projector
Computer
RGB
output
terminal
RGB cable (supplied) COMPUTER/
COMPONENT
See page 66 “Computer Compatibility Chart” for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may cause some of the functions to not
work.
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
Depending on the computer you are using, an image may not be projected unless the
computer's external output port is switched on (e.g. Press “Fn” and “F5” keys
simultaneously when using a SHARP notebook computer). Refer to the specifi c instructions in
your computer's operation manual to enable your computer's external output port.
•
•
•
Note
•
•

22
Connecting the Projector to Other Equipment (Continued)
Equipment
Terminal on
connected equipment
Cable Terminal on the
projector
Video equipment Component
video output
terminal
3 RCA to mini D-sub 15 pin cable
(optional, AN-C3CP2)
COMPUTER/
COMPONENT
S-video
output
terminal
S-video cable (commercially available) S-VIDEO
Video output
terminal
Video cable (commercially available) VIDEO
Camera/Video game
Component
video
output
terminal
Cables for a camera or a video game/3 RCA to
mini D-sub 15 pin cable (optional, AN-C3CP2)
RCA adaptor plug
(commercially available)
COMPUTER/
COMPONENT
S-video
output
terminal
Cables for a camera or a video game S-VIDEO
Video
output
terminal
Cables for a camera or a video game VIDEO
When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that ts in the projector terminal you want to connect.
The projector does not support RGBC signals via the Euro-scart.
•
•
Note

23
Connections
Equipment
Terminal on
connected equipment
Cable Terminal on the
projector
Audio equipment ø3.5 mm
audio output
terminal
ø3.5 mm stereo or mono audio cable
(commercially available or available
as Sharp service part QCNWGA038WJPZ)
AUDIO 1
RCA audio
output
terminal
RCA audio cable (commercially available)
AUDIO 2
Audio
output
terminal
Cables for a camera or a video game
Monitor RGB
input
terminal
RGB cable (supplied or commercially
available)
MONITOR OUT
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
stereo audio cable.
You can select “Audio 1” or “Audio 2” in the INPUT list. (See page 29.)
RGB signals and Component signals can be output to the monitor.
•
•
•
Note

24
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-
232C adaptor (optional, AN-A1RS) and an RS-232C serial control cable (cross type,
commercially available), the computer can be used to control the projector and check the status
of the projector. See page 61 for details.
When connecting to a computer using a DIN-D-sub RS-232C adaptor (optional,
AN-A1RS) and an RS-232C serial control cable
RS-232C serial control cable (cross type, commercially available)
Computer
DIN-D-sub RS-232C
adaptor (optional, AN-A1RS)
To RS-232C terminal
To RS-232C terminal
The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
See pages 59 and 60 for connection of an RS-232C serial control cable.
•
•
Note
Info
Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This
may damage your computer or projector.
Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.
This may damage your computer.
•
•
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
Then plug into AC outlet.
AC socket
To AC outlet
Power cord
(supplied)
AC socket
To AC outlet
Power cord
(supplied)

25
Basic
Operation
Turning the Projector On/Off
Info
When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet
or the breaker switch is turned off when the
projector is on, then the projector
automatically turns on when the power cord
is plugged into the AC outlet or the breaker
switch is turned on. (See page 49.)
English is the factory default language. If you
want to change the on-screen display to
another language, change the language
according to the procedure on page .48
•
•
STANDBY/ON button
Lamp indicator
Power indicator
STANDBY
button
ON button
On-screen display (con rmation message)
Info
Direct Power Off function:
You can unplug the power cord from the AC
outlet even if the cooling fan is still running.
•
Turning the Projector On
Note that the connections to external
equipment and power outlet should be
done before performing the operations
written below. (See pages 21 to 24.)
Open the lens shutter fully and press
STANDBY/ON on the projector or ON
on the remote control.
The power indicator illuminates green.
After the lamp indicator illuminates, the projector
is ready to start operation.
About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green: The lamp is warming up.
Red: The lamp is shut down
abnormally or the lamp should be
replaced.
When switching on the projector, a slight
ickering of the image may be experienced
within the rst minute after the lamp has been
illuminated. This is normal operation as the
lamp's control circuitry is stabilising the lamp
output characteristics. It should not be
regarded as faulty operation.
If the projector is put into Standby mode and
immediately turned on again, the lamp may
take some time to start projection.
When System Lock is set, the keycode input
box appears. To cancel the keycode setting,
input the keycode that you have already set.
See page 50 for details.
•
•
•
•
Note
Turning the Power Off (Putting
the Projector into Standby Mode)
Press STANDBY/ON on the projector
or STANDBY on the remote control,
then press that button again while the
con rmation message is displayed, to
put the projector into Standby mode.
The projector cannot be turned on while cooling.
•
•
•

26
Image Projection
About the Setup Guide
After turning on the projector, the Setup
Guide screen appears to assist you with
projector setup.
Guidance items
1 FOCUS
2 HEIGHT ADJUST
3 ZOOM
Press ENTER to exit the Setup Guide
screen.
The Setup Guide screen automatically
highlights the items in the following order:
1 FOCUS
3 ZOOM4 ENTER
2 HEIGHT ADJUST
However, you can adjust the focus or height
(angle) regardless of the highlighted item.
If you do not want to display the Setup Guide
for the next time, set “Menu” - “SCR - ADJ” -
“Setup Guide” to “Off”. (See page 48.)
•
•
Note
Adjusting the Projected Image
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Rotate the focus ring to adjust the
focus while watching the projected
image.
Using the knob on the focus ring will make the
adjustments easier.
•
Setup Guide screen
ENTER button
Focus ring

27
Basic
Operation
2 Adjusting the Height
The height of the projector can be
adjusted using the adjustment feet at the
front and rear of the projector.
When the screen is above the projector,
the projection image can be made higher
by adjusting the projector.
1 Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
2 Remove your hands from the
HEIGHT ADJUST lever of the
projector after its height has
been nely adjusted.
The angle of projection is adjustable up to
9 degrees from the surface on which the
projector is placed.
3 Use the rear adjustment foot to
make the projector level.
The projector is adjustable ±2 degrees
from the standard position.
When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the
procedures in Keystone Correction to correct
the distortion. (See pages 28 and 46.)
•
Note
3 Adjusting the Picture Size
You can adjust the picture size using the
zoom ring on the projector.
Rotate the zoom ring to enlarge or
shrink the picture size.
Using the knob on the zoom ring will make the
adjustments easier.
•
Zoom ringZoom ring
•
•
1
2
3
Rear adjustment footRear adjustment foot
HEIGHT ADJUST lever
Make small
adjustments.
Info
Do not apply too much pressure on the
projector when the front adjustment foot
comes out.
When lowering the projector, be careful not to
get your ngers caught in the area between
the adjustment foot and the projector.
Hold the projector rmly while lifting or carrying.
Do not hold by the lens area.
•
•
•
•

28
Correcting Trapezoidal
Distortion
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is called
Keystone Correction.
The Keystone Correction can be adjusted up
to an angle of approximately ±40 (XR-55X)/
±20 (XR-50S) degrees and the screen can
also be set up to an angle of approximately
±40 (XR-55X)/±20 (XR-50S) degrees.
•
Note
1 Press KEYSTONE to enter the
Keystone Correction mode.
2 Press P Q O R/ or / to adjust the
Keystone Correction.
To return to the default setting, press
RETURN while the on-screen display of the
Keystone Correction mode is on the screen.
•
Note
3 Press KEYSTONE.
The on-screen display of the Keystone
Correction mode will disappear.
•
1
2
3
KEYSTONE button
Adjustment buttons
(P R/ /O Q/ )
RETURN button
On-screen display
(Keystone Correction mode)
0KEYSTONE
ADJUST END
Shrinks upper side.
(Move the slide bar in the + direction.)
Shrinks lower side.
(Move the slide bar in the - direction.)
Info
While adjusting the image using Keystone
Correction, straight lines and the edges of the
image may appear jagged.
•
Image Projection (Continued)

29
Basic
Operation
Switching the Input Mode
Select the appropriate Input mode for the
connected equipment.
Press INPUT
/
to display the
INPUT list.
Use INPUT
/
to select the Input
mode, and use / to select the O Q
audio input terminal.
Adjusting the Volume
Press VOL +/ on the remote control –
or – +O Q/ on the projector to adjust
the volume.
Pressing VOL–/–O will lower the volume.
Pressing VOL+/Q+ will raise the volume.
When the projector is connected to external
equipment, the volume level of the external
equipment changes in accordance with the
volume level of the projector. Set the projector's
volume to the lowest level when turning the
projector on/off or when changing the input signal.
When you do not want to output the sound
from the projector's speaker while the
projector is connected to external equipment,
set “Speaker” in the “PRJ-ADJ1” menu to
“Off”. (See page 49.)
•
•
•
•
Note
Displaying the Black Screen
and Turning Off the Sound
Temporarily
Press AV MUTE on the remote control
or close the lens shutter to temporarily
display a black screen and turn off the
sound.
Pressing AV MUTE again will turn the
projected image back on.
When you close the lens shutter, the projector will
be set to AV Mute mode and then the projector will
be turned off automatically after about 30 minutes.
•
•
Note
VOL +/– (Volume)
buttons
INPUT buttons
AV MUTE button
O Q/ buttons
VOL +/– (Volume)
buttons
INPUT buttons
AV MUTE button
O Q/ buttons
On-screen displayOn-screen display
On-screen displayOn-screen display

30
Resize Mode
This function allows you to modify or customize the Resize mode to enhance the input
image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
See page 46 for setting on menu screen.
COMPUTER
Main resolution NORMAL FULL NATIVE BORDER 16:9
XR-55X
SVGA (800 × 600) 1024 × 768 — 800 × 600
768 × 576 1024 × 576
XGA (1024 × 768) —
SXGA (1280 × 1024) 968 × 768 1024 × 768 1280 × 1024
1280 × 800 1024 × 640 1280 × 800 922 × 576
XR-50S
SVGA (800 × 600) 800 × 600 — —
600 × 450 800 × 450
XGA (1024 × 768) 1024 × 768
SXGA (1280 × 1024) 750 × 600 800 × 600 1280 × 1024
1280 × 800 800 × 500 1280 × 800 720 × 450
Input signal For 4:3 screen For 16:9 screen
Computer
Image type NORMAL FULL NATIVE BORDER 16:9
XR-55X XR-50S
Resolution
lower than
XGA
Resolution
lower than
SVGA
4:3 aspect ratio
—
*2
*1, *3 *1
XGA SVGA
—
*2
Resolution
higher than
XGA
Resolution
higher than
SVGA
SXGA (1280 × 1024)
5:4 aspect ratio
1280 × 720
16:9 aspect ratio
*1
—
*2
—
*2
1360 × 768
1366 × 768
1280 × 768
16:10 aspect ratio
*1 *1 *1
1280 × 800
: Cutout area on which images cannot be projected
: Area where the signals are off screen
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode
*3 For XR-50S model, “Border” cannot be selected with certain resolution selections in which the horizontal part of aspect ratio
becomes smaller than 4:3 (such as 1280 × 1024, among others).
•RESIZE
button
RESIZE
button
Image Projection (Continued)

31
Basic
Operation
VIDEO/DTV
Input signal For 4:3 screen For 16:9 screen
Video/DTV Image type NORMAL AREA ZOOM V-STRETCH BORDER 16:9
480I, 480P,
576 I, 576P,
NTSC, PAL,
SECAM
4:3 aspect ratio
*1 *1
Squeeze
*1 *1
Letter box
*1 *1
720P, 1035I,
1080I, 1080P
16:9 aspect ratio
*1
—
*2
—
*2
540P
16:9 aspect ratio
(4:3 aspect ratio in 16:9)
*1
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
About Copyrights
When using the Resize function to select an image size with a different aspect ratio to a TV
program or video image, the image will look different from its original appearance. Keep this
in mind while choosing an image size.
The use of the Resize or Keystone Correction function to compress or stretch the image for
commercial purposes/public displays in a café, hotel, etc. may be an infringement of
copyright protected by law for copyright holders. Please use caution.
•
•

32
Operating with the Remote Control
POINTER button
ECO+QUIET button
Adjustment buttons
(P R/ /O Q/ )
BREAK TIMER button
SPOT button
AUTO SYNC button
FREEZE button
PICTURE MODE button
MAGNIFY buttons
EFFECT button
Displaying and Setting the
Break Timer
1 Press BREAK TIMER.
The timer starts to count down from 5
minutes.
On-screen display
2 Press P R/ /O Q/ to adjust the
length of the break time.
Increases with P or Q
5 minutes ➞ 6 minutes ➞ 60 minutes
Shortens with O or R
4 minutes ➞ 3 minutes ➞1 minute
The break time can be set in units of one
minute (up to 60 minutes).
Canceling the break timer display function
Press BREAK TIMER.
The Break Timer is not available while the
projector is operating the following functions.
- Auto Sync
- Freeze
- AV Mute
- Input Search
•
Note
•
•
•
•
1
2
Displaying the Pointer
1 Press POINTER and press /P R/
O Q/ on the remote control to
move the pointer.
Press EFFECT to change the pointer icon
(5 types).
Star Finger1 Finger2 Heart Underline
2 Press POINTER again.
The pointer will disappear.
Using the Spot Function
1 Press SPOT and press /P R/O Q/
on the remote control to move
the spot area.
Press EFFECT to change the spot area
size (3 types).
1/9 1/25 1/8
2 Press SPOT again.
The spot area will disappear.
Switching the Eco+Quiet
Mode
Press ECO+QUIET to switch the
Eco+Quiet mode between on and off.
When the Eco+Quiet Mode is set to “ON”, the
sound of the cooling fan will turn down, the power
consumption will decrease, and the lamp life will
extend.
Refer to “Eco+Quiet” on page 43 for details.•
Note
•
•
•
•
•
1
2
1
2

33
Useful
Features
Auto Sync
(Auto Sync Adjustment)
Auto Sync function works when detecting
input signal after the projector turns on.
Press AUTO SYNC to manually adjust
with Auto Sync function.
When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
adjustments. (See page 44.)
•
Note
Freezing a Moving Image
1 Press FREEZE.
The projected image is frozen.
2 Press FREEZE again to return to
the moving image from the
currently connected device.
Selecting the Picture Mode
You can select the appropriate Picture
mode for the projected image, such as
movie or video game.
Press PICTURE MODE.
When pressing PICTURE MODE, the Picture
mode changes in the following order:
STANDARD PRESENTATION MOVIE GAME sRGB
*
See page 41 for details on the Picture mode.•
Note
* “sRGB” is displayed only when RGB signal is input.
•
•
1
2
Displaying an Enlarged
Portion of an Image
Graphs, tables and other portions of
projected images can be enlarged. This
is helpful when providing more detailed
explanations.
1 Press MAGNIFY on the
remote control.
Enlarges the image.
Pressing or MAGNIFY enlarges
or reduces the projected image.
× × × ×1 2 3 4
Press
.
Press
.
You can change the location of the
enlarged image using P, R, and O Q.
•
Note
2 Press RETURN on the remote
control to cancel the operation.
The magni cation then returns to ×1.
The selectable magni cations differ
depending on the input signal.
In the following cases, the image will
return to the normal size (×1).
- When switching the Input mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and
refresh rate (vertical frequency)
change.
- When the Resize mode is changed.
•
•
Note
•
•
•
1
2

34
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use the
remote control as the computer mouse.
If the computer is placed too far away from the projector to be connected via the USB
cable, the remote receiver (optional, AN-MR2) makes it possible to operate the
projector with the remote control. For details, see the operation manual of the
receiver.
Connecting with a USB cable
or
R
emote receiver
(optional, AN-MR2)
To USB terminal
USB cable
(commercially available or available as
Sharp service part QCNWGA014WJPZ)
To USB terminal
Computer
The mouse pointer can be
operated in the following way
after it is connected.
When moving the cursor
Press MOUSE/Adjustment buttons ( /P R/O Q/ ).
When left-clicking
Press L-CLICK.
When right-clicking
Press R-CLICK.
When your computer supports only a
one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK.
L-CLICK and R-CLICK have common function.
When using [Page Up] or [Page Down]
■
■
■
■
■
MOUSE/Adjustment
buttons ( / / / ) ? _
R-CLICK button
L-CLICK button
PAGE UP/
PAGE DOWN button
s
MOUSE/Adjustment
buttons ( / / / ) ? _
R-CLICK button
L-CLICK button
PAGE UP/
PAGE DOWN button
s
Same as the [Page Up] and [Page Down] keys
on a computer keyboard.
Press PAGE UP or PAGE DOWN.
This function only works with the Microsoft
® Windows® OS and Mac OS® that support USB.
You cannot use this function when displaying the menu screen.
Confi rm that the computer recognizes the USB connection.
•
•
•
Note
Operating with the Remote Control (Continued)

35
Useful
Features
Menu Items
The following shows the items that can be set in the projector.
“Picture” menu
Main menu Sub menu
Picture
Page Page 41 41
Page 42
Page 42
Page 42
Page 42
Page 42
Page 43
Page 43
+30-30Contrast
+30-30
+30-30
+30-30
1-1
20
+30-30
+30-30
+30-30
Tint
Color
Sharp
Bright
Film Mode
Eco+Quiet
[On/Off]
Reset
Auto
Off
CLR Temp
BrilliantColor™
C.M.S. Setting [On/Off]
C.M.S.
Standard
Presentation
Movie
Game
sRGB*1
Picture Mode
*2
*2
*2
Red
Blue
*2
Page 43
DNR Level 1
Level 2
Level 3
C.M.S.-Hue
C.M.S.-Saturation
C.M.S.-Value
Page 42
Page 42
Page 42
Reset
Return
+30-30R
+30-30
+30-30
+30-30
+30-30
+30-30C
G
B
Y
M
Reset
*1 Item when inputting RGB signal through
COMPUTER.
*2 Items when inputting component signal through
COMPUTER, or when selecting S-VIDEO or VIDEO.
“Quick Start Menu”
Main menu
Normal
Full
Native
Area Zoom
V-Stretch
Border
16:9
Quick Start Menu
Input Search Start
Resolution
Eco + Quiet
[On/Off]
Resize
Information
Go To Complete Menu
Keystone
Language
Sub menu
Page 39
Page 39
Page 39
Page 39
Page 39
Page 39
Page 39
Page 39
+80-80
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
polski
Magyar
Türkçe

36
“Screen adjustment (SCR-ADJ)” menu
Main menu Sub menu
SCR - ADJ
Page 46
Language
Image Shift
Resize
Page 46
Page 46
Page 46
Page 47
Page 48
Page 48
Page 48
Keystone
OSD Display [On/Off]
Page 47
Closed Caption
Page 47
Overscan [On/Off]
Background
PRJ Mode
Logo
Blue
None
Page 48
Wall Color Off
Blackboard
Whiteboard
Page 48
Setup Guide [On/Off]
Off
CC1
CC2
Front
Ceiling + Front
Rear
Ceiling + Rear
+96 *7-96
+75 *8-75
+80 *7-80
+40 *8-40
Normal
Full
Native
Area Zoom
V-Stretch
Border
16:9
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
polski
Magyar
Türkçe
*7 Adjustment range for XR-55X.
* S8 jus m t range r -5 Ad t en fo XR 0.
“Signal adjustment (SIG-ADJ)” menu
Main menu Sub menu
SIG-ADJ
Page 44
Page 44
Page 44
Page 44
Page 45
Signal Type
Video Setup
Signal Info
Auto
RGB
YPbPr
Resolution
0 IRE
7.5 IRE
Page 45
Page 45
Video System Auto
PAL
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
+30-30
+60-60
+150-150
+150-150Clock
Phase
H-Pos
V-Pos
Reset
*3
*3
*4
*4
*4
*5
*6
*3 Items when inputting RGB signal through
COMPUTER/COMPONENT.
*4 Items when inputting COMPUTER/COMPONENT.
*5 Item when selecting COMPUTER/COMPONENT.
*6 Item when selecting S-VIDEO or VIDEO.
Menu Items
(Continued)

37
Useful
Features
“Projector adjustment (PRJ-ADJ1/2)” menu
Main menu Sub menu
PRJ-ADJ1
Page 49
Speaker [On/Off]
System Lock
[Enable/Disable]
Keylock [On/Off]
Auto Restart [On/Off]
Page 49
Auto Power Off [On/Off]
Page 49
Page 49
Page 50
Page 51
Fan Mode
Page 50
Normal
High
RS-232C
Page 49
9600bps
38400bps
115200bps
Auto Sync [On/Off]
Page 49
Main menu Sub menu
Page 51
Page 52
Page 52
Page 52
Page 52
Page 51
PRJ-ADJ2
FUNCTION Button Input Search
Audio Mute
Image Shift
Signal Info
STANDBY Mode Quick Start
Eco
All Reset
Lamp Timer (Life)
Page 52
DLP
®
Link
TM
[On/Off]
DLP
®
Link
TM
Invert
Quick Start Menu [On/Off]
Page 49
*9
*9
*9 This item is available for XR-55X only.

38
Adjustment buttons
(P R/ /O Q/ )
ENTER button
RETURN button
Press RETURN to return
to the previous screen
when the menu is
displayed.
•
MENU button
Adjustment buttons (P R/ /O Q/ )
MENU button
ENTER button
Menu Selections (Quick Start Menu)
This operation can also be performed by using the buttons on the projector.•
1 Press MENU.
The “Quick Start Menu” screen for the
selected Input mode is displayed.
2 Press P R or to select the
desired item, then press ENTER.
3 Press P R/ /O Q/ to adjust the
item selected, then press
ENTER.
Info
To display the advanced settings and
adjustments, select “Go To Complete Menu”.
Press ENTER to display the Complete Menu
screen.
If you do not want to display the Quick Start
Menu, set “Go To Complete Menu” - “PRJ-ADJ2”
- “Quick Start Menu” to “Off”. (See page 51.)
•
•
•
1
2
3
Example
SEL./ADJ. ENTER END
Input Search Start
Resolution
Resize
0
ECO+Quiet
Language
Keystone
Information
1024×768
Normal
English
Off
Quick Start Menu
Go To Complete Menu…
Using the Menu Screen
Select from the Quick Start Menu, which is a collection of the most frequently used
functions, or the Complete Menu, which enables advanced settings and adjustments.

39
Useful
Features
Quick Start Menu
The following items can be con gured on the Quick Start Menu.
Selectable items Description
Input Search Start Automatically searches for and switches to the appropriate Input mode.
Pressing an operation button during input searching cancels the search.
Resolution Manually change the resolution.
Use this function when the image and screen size do not match with the
resolution selected automatically. (See page 44.)
R esize Changes the Resize mode.
Use this function to stretch the image vertically or horizontally or when the
edges of the image cannot be seen. (See page 46.)
Keystone Corrects the keystone distortion of projected images.
Use this function to correct the trapezoidal distortion of images caused when
projecting images at an angle to the screen. (See page 46.)
Eco+Quiet When set to “On”, this function reduces the cooling fan noise and power
consumption, thereby prolonging the operating life of the lamp. (See page 43.)
Language Selects the language displayed on the screen. (See page 48.)
Information Displays the input signal, lamp use time, remaining lamp life, etc.
Go To Complete Menu Displays the Complete Menu for advanced settings and adjustments.
The setting of Resize mode will be made independently for each Input mode.
The setting of Eco+Quiet mode will be made independently for each Input mode and each Picture mode.
•
•
Note
Menu Selections (Complete Menu)
Example: Adjusting “Bright”.
This operation can also be performed by using the buttons on the projector.•
1 Press MENU.
The “Quick Start Menu” screen is
displayed.
2 Press P R or to select “Go To
Complete Menu”.
3 Press Q O or and select
“Picture” to adjust.
Info
When “PRJ-ADJ2” - “Quick Start Menu” is
set to “On”, pressing MENU displays the
Quick Start Menu screen.
•
•
1
2
3
Example: “Picture” screen menu for
COMPUTER (RGB) input
Menu item
Picture Mode
Contrast 0
0
0
Bright
Standard
SEL./ADJ. ENTER END
0
0
Red
Blue
CLR Temp
BrilliantColor
TM
C.M.S. Setting
C.M.S.
Eco+Quiet
0
1
On
Off
DNR Level 2
Reset
SIG SCR PRJ1 PRJ2Picture

40
4 Press P R or and select “Bright”
to adjust.
The selected item is highlighted.
To adjust the projected
image while watching it
Press ENTER.
The selected item (e.g. “Bright”) is
displayed by itself at the bottom of the
screen.
When pressing P or R, the following item
(“Red” after “Bright”) will be displayed.
Press ENTER again to return to the
previous screen.
•
Note
5 Press O Q or to adjust the item
selected.
The adjustment is stored.
6 Press MENU.
The menu screen will disappear.
•
•
•
•
•
4
0Bright
Picture
SEL./ADJ. Rtn. Menu END
Picture Mode Standard
SEL./ADJ. Single ADJ END
Resize
Image Shift 0
0Keystone
Border
Picture Mode
Contrast 0
0
Standard
SEL./ADJ. END
0
0
Red
Blue
CLR Temp
BrilliantColor
T M
C.M.S. Setting
C.M.S.
Eco+Quiet
0
1
On
Off
Reset
Bright 0
DNR Level 2
Picture
Pict. SCR-ADJ
SIG PRJ1 PRJ2
SIG SCR PRJ1 PRJ2Picture
Items to be adjusted
The item displayed by itself
Press ENTER.
0Bright
Picture
SEL./ADJ. Rtn. Menu END
Picture Mode Standard
SEL./ADJ. Single ADJ END
Resize
Image Shift 0
0Keystone
Border
Picture Mode
Contrast 0
0
Standard
SEL./ADJ. END
0
0
Red
Blue
CLR Temp
BrilliantColor
T M
C.M.S. Setting
C.M.S.
Eco+Quiet
0
1
On
Off
Reset
Bright 0
DNR Level 2
Picture
Pict. SCR-ADJ
SIG PRJ1 PRJ2
SIG SCR PRJ1 PRJ2Picture
Items to be adjusted
The item displayed by itself
Press ENTER.
5
Picture Mode
Contrast 0
0
Standard
SEL./ADJ. Single ADJ END
0
0
Red
Blue
CLR Temp
BrilliantColorT M
C.M.S. Setting
C.M.S.
Eco+Quiet
0
1
On
Off
Reset
1 5Bright
DNR Level 2
Picture SIG SCR PRJ1 PRJ2
Picture Mode
Contrast 0
0
Standard
SEL./ADJ. Single ADJ END
0
0
Red
Blue
CLR Temp
BrilliantColorT M
C.M.S. Setting
C.M.S.
Eco+Quiet
0
1
On
Off
Reset
1 5Bright
DNR Level 2
Picture SIG SCR PRJ1 PRJ2
6
The MENU button is not available while the projector is operating:
- Auto Sync/Break Timer/Freeze/AV Mute/Input Search
•
Note
Using the Menu Screen
(Continued)

41
Useful
Features
Picture Adjustment (“Picture” Menu)
Menu operation n Page 39
Q PAGE1 PAGE2Q
Picture Mode
Contrast 0
0
0
0
Bright
Color
Tint
0Sharp
Standard
SEL./ADJ. ENTER END
0
0
Red
Blue
Picture SIG SCR PRJ1 PRJ2
1
2
Picture Mode
CLR Temp
BrilliantColor
T M
C.M.S. Setting
C.M.S.
Standard
SEL./ADJ. ENTER END
Film Mode
Eco+Quiet
0
1
On
Auto
Off
DNR Level 2
Reset
7
6
5
4
2
3
Picture SIG SCR PRJ1 PRJ2
1 Selecting the Picture Mode
Selectable
items Description The default settings of each item when selecting Picture Mode
CLR Temp BrilliantColor
TM Eco+Quiet
Standard For standard image 0 1 Off
Presentation Brightens portions of image for
more enhanced presentations.
0 2 Off
Movie Gives natural tint to the
projected image.
–1 0 On
Game Gives sharpness to the
projected image.
0 1 Off
*sRGB For high fi delity reproduction of
images from a computer.
– – Off
“sRGB” is displayed only when RGB signal is input.
You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are
retained in memory.
You can also press PICTURE MODE on the remote control to select the Picture mode. (See page 33.)
*sRGB is an international standard of color reproduction regulated by the IEC (International
Electrotechnical Commission). As the fi xed color area has been decided by the IEC, the images are
displayed in a natural tint based on an original image, when “sRGB” is selected.
You cannot set the items, “Red”, “Blue”, “CLR Temp”, “BrilliantColor
TM”, when “sRGB” is selected.
•
•
Note
Info
When “sRGB” is selected, the projected image may become dark, but this does not indicate a
malfunction.
•
•
•

42
Picture Adjustment (“Picture” Menu)
(Continued)
Menu operation n Page 39
2 Adjusting the Image
Adjustment
items O Q button button
Contrast For less
contrast.
For more
contrast.
Bright For less
brightness.
For more
brightness.
Color* 1For less color
intensity.
For more color
intensity.
Tint*1 For making skin
tones purplish.
For making skin
tones greenish.
Sharp*
1For less
sharpness.
For more
sharpness.
Red*2For weaker red. For stronger
red.
Blue*2For weaker
blue.
For stronger
blue.
BrilliantColor™*
2
*
3
For making the
effect weaker.
For making the
effect stronger.
*1 Not displayed in the RGB input mode.
*2 Not adjustable/selectable when selecting “sRGB”.
*3 BrilliantColor™ uses Texas Instruments'
BrilliantColor™ technology. As the BrilliantColor™
level is increased, the image becomes brighter
while the color reproduction is kept at a high level.
“Red”, “Blue”, “BrilliantColor
TM” and “CLR
Temp” cannot be set when “sRGB” is
selected.
To reset all adjustment items, select “Reset”
and press .ENTER
•
•
Note
3
Adjusting the Color
Temperature
Selectable
items Description
–1
0
1
For lower color temperature for
warmer, reddish incandescent-like
images.
For higher color temperature for
cooler, bluish, fl uorescent-like images.
Values on “CLR Temp” are only for general
standard purposes.
•
Note
4 Adjusting the Colors
This function adjusts each of the six main
colors that comprise the color wheel, altering
their “Hue”, “Saturation”, or “Value”.
Selectable items Description
C.M.S.-Hue Sets the hue of the main colors.
C.M.S.-Saturation Sets the saturation of the main
colors
C.M.S.-Value Sets the brightness of the main
colors.
Reset The adjustments of “Hue”,
“Saturation” and “Value” of all
colors are reset to the default
setting.
Return Returns to the “Picture” menu
screen.
Adjusting “Hue”, “Saturation”, or “Value”.
1 Select “On” for “C.M.S. Setting” in the “Picture”
menu and then press ENTER.
2 Select “C.M.S.” in the “Picture” menu and then
press ENTER.
3 Press P R or to select either “Hue”, “Saturation”, or
“Value” and then press ENTER.
4 Select the color to be adjusted with and P or R
adjust it with O or Q.
Example of adjusting the “Hue”
Main colors O button buttonQ
R (Red)
Closer to magenta
Closer to yellow
Y (Yellow) Closer to red Closer to green
G (Green) Closer to yellow Closer to cyan
C (Cyan) Closer to green Closer to blue
B (Blue) Closer to cyan
Closer to magenta
M (Magenta) Closer to blue Closer to red
When “Saturation” is selected, the selected
color becomes
O: lighter. Q: thicker.
When “Value” is selected, the selected color
becomes
O: darker. Q: brighter.
To reset the adjustment values of each color to
the default settings, select “Reset” and press
ENTER.
•
•
•

43
Useful
Features
5
Selecting the Film Mode
This function provides high-quality playback
of images originally projected at 24 fps, such
as movies on DVDs.
Selectable
items Description
Auto Films are detected automatically.
Off Films are not detected.
This function is available for the following
signals.
With COMPUTER/COMPONENT input:
- 480I
- 576I
- 1035 (XR-55X only)I
- 1080I (XR-55X only)
With S-VIDEO or VIDEO input:
- All signals
•
Note
6
Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides
high quality images with minimal dot crawl
and cross color noise.
Selectable
items Description
Level 1
Sets the DNR level for viewing a
clearer picture.
Level 2
Level 3
Menu operation n Page 39
7 Eco+Quiet
Selectable
items Brightness and Power consumption
On Approx. 75%
Off 100%
When “Eco+Quiet” is set to “On”, the fan
sound and power consumption are lower than
they are when “Off” is selected. (Projection
brightness decreases as shown in the chart.)
•
Note

44
Signal Adjustment (“SIG-ADJ” Menu)
Menu operation n Page 39
0
0
0
0
Phase
Clock
H-Pos
V-Pos
Reset
Auto
1024 x 768
0 IRE
Resolution
Signal Type
Video Setup
AutoVideo System
Signal Info : 1024 x 768
H 48.3 kHz / V 60.0 Hz
SEL./ADJ. ENTER END
Pict. SCR PRJ1 PRJ2SIG-ADJ
1
3
4
5
6
2
1
Adjusting the Computer Image
If the optimum image cannot be obtained with
Auto Sync adjustment, use the SIG-ADJ function.
Selectable
items Description
Clock Adjusts vertical noise.
Phase Adjusts horizontal noise (similar to
tracking on your VCR).
H-Pos Centers the on-screen image by
moving it to the left or right.
V-Pos Centers the on-screen image by
moving it up or down.
To reset all adjustment items, select “Reset”
and press .ENTER
The adjustable range of “H-Pos” (H-Position)
and “V-Pos” (V-Position) may vary depending
on the screen resolution of the computer.
•
•
Note
2 Resolution Setting
Ordinarily, the type of input signal is detected and
the correct Resolution mode is automatically
selected. However, for some signals, the optimal
Resolution mode in “Resolution” may need to be
selected to match the computer display mode.
See “Checking the Input Signal” on page 45
for information on the currently selected input
signal.
•
Note
3 Signal Type Setting
This function allows you to select the input signal
type RGB or Component for COMPUTER/
COMPONENT.
Selectable
items Description
Auto Input signals are automatically
recognized as RGB or component.
RGB Set when RGB signals are received.
YPbPr Set when Component signals are
received.

45
Useful
Features
4
Setting the Video System
The video input system mode is factory preset
to “Auto”; however, a clear picture from the
connected audio-visual equipment may not be
received, depending on the Video signal
difference.
In that case, switch the Video signal.
Selectable items
Auto
PAL
SECAM
*NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL -60
* When reproducing NTSC signals in PAL
video equipment.
The Video signal can only be set in S-VIDEO
or VIDEO mode.
When “Video System” is set to “Auto”, you
may not receive a clear picture due to signal
differences. Should this occur, switch to the
video system of the source signal.
•
•
Note
5
Setting the Video Setup
Selectable
items Description
0 IRE Set s the black level to 0 IRE.
7.5 IRE Sets the black level to 7.5 IRE.
This function is available for the following
signals.
With COMPUTER/COMPONENT input:
- 480I
With S-VIDEO or VIDEO input:
- NTSC3.58
•
Note
Menu operation n Page 39
6
Checking the Input Signal
This function allows you to check the current
input signal information.

46
Adjusting the Projected Image (“SCR-ADJ” Menu)
Menu operation n Page 39
SEL./ADJ. ENTER END
Resize
Image Shift 0
0Keystone
OSD Display
Closed Caption
Overscan
Background
Setup Guide
PRJ Mode
On
Front
Wall Color
Language
Off
English
On
Off
Logo
On
Normal
Pict. PRJ1 PRJ2SIG SCR-ADJ
9
8
0
5
6
4
3
2
1
7
1
Setting the Resize Mode
Use this function to stretch the image
vertically or horizontally or when the edges of
the image cannot be seen.
For details of the Resize mode, see pages
30 and 31.
You can also press RESIZE on the remote
control to set the Resize mode. (See page 30.)
•
•
Note
2 Adjusting the Image
Position
You can move the projected image vertically.
Q buttonO button
This function only works in some Resize
modes. (See pages 30 and 31.)
•
Note
3 Keystone Correction
When the image is projected either from the top
or from the bottom towards the screen at an
angle, the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called Keystone Correction.
Select “Keystone” on the “SCR-ADJ”
menu and adjust with the slide bar.
See page 28 for details of Keystone Correction.
O buttonQ button
The Keystone Correction can be adjusted up
to an angle of approximately ±40(XR-55X)/
±20(XR-50S) degrees.
You can also press KEYSTONE on the
remote control to adjust Keystone Correction.
•
•
Note

47
Useful
Features
4 Setting the Overscan
This function allows you to set the overscan area
(display area).
Selectable
items Description
On The input area is displayed without the
screen edges.
Off The whole input area is displayed.
This function is available for the following
signals.
With COMPUTER/COMPONENT input:
- 480P
- 540P
- 576P
- 720P
- 1035I
- 1080I/1080P
If noise appears at the screen edges when
“Off” is selected, set the function to “On”.
Also see “About Copyrights” on page 31.
•
•
•
Note
5
Setting the On-screen
Display
Selectable
items Description
On All on-screen displays are displayed.
Off VOLUME/AV MUTE/FREEZE/AUTO
SYNC/RESIZE/PICTURE MODE/
ECO+QUIET/MAGNIFY/Input Search/
Audio Mute/“An invalid button has
been pressed.” are not displayed.
6 Closed Caption
<For Americas only>
Info
This function is available for NTSC3.58 signal.
This function does not work when the Resize
mode is set to “Border”.
This function is available in the following cases
only:
Resize mode Keystone Correction
Normal
Area Zoom
V-Stretch
-40 − +40
(XR-55X only)
16:9 -12 − +12
•
•
•
“Closed Caption” is a system which allows
conversations, narration, and sound effects in TV
programs (Limited regions) and home videos to
be viewed as captions on the screen.
Not all programs and videos will offer closed
captioning. Please look for the symbol to
ensure that captions will be shown.
Two channels are available: CC1 and CC2.
Selectable
items Description
Off —
CC1 Closed Caption mode for CH1 data
CC2 Closed Caption mode for CH2 data
Closed Caption may malfunction (white blocks,
strange characters, etc.) if signal conditions are
poor or if there are problems at the broadcast
source. This does not necessarily indicate a
problem with the projector.
If any button is pressed to call up the on-
screen display while viewing a Closed Caption
broadcast, the closed captions will disappear.
•
•
Note
•
•
•
Menu operation n Page 39

48
7 Selecting the Background
Image
Selectable items Description
Logo Sharp logo screen
Blue Blue screen
None —
8
Selecting the Setup Guide
Selectable items Description
On Displaying the Setup Guide
when turning the projector on.
Off Not displaying the Setup Guide.
9 Reversing/Inverting
Projected Images
Selectable items Description
Front Normal image (Projected from
the front of the screen)
Ceiling + Front Inverted image (Projected from
the front of the screen with an
inverted projector)
Rear Reversed image (Projected from
the rear of the screen or with a
mirror)
Ceiling + Rear Reversed and inverted image
(Projected with a mirror)
See page for details of Projection (PRJ) Mode.20
Adjusting the Projected Image (“SCR-ADJ” Menu)
(Continued)
Menu operation n Page 39
0
Selecting the Wall Color
This function allows you to project the image
to a colored (white or dark green) surface or
wall without using a screen.
Selectable items Description
Off The Wall Color function is not
activated.
Blackboard Projects images onto a
blackboard (dark green).
Whiteboard Projects images onto a
whiteboard.
Selecting the On-screen
Display Language
The projector can switch the on-screen
display language among 17 languages.
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Türkçe
polski
Magyar

49
Useful
Features
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)
Menu operation n Page 39
Q PRJ-ADJ1
SEL./ADJ. ENTER END
Auto Power Off On
Auto Restart On
Speaker On
OffKeylock
9600bps
System Lock
RS-232C
Fan Mode Normal
Disable
Auto Sync On
Pict. SCR PRJ-ADJ1SIG PRJ2
1
2
3
4
5
7
6
8
1 Auto Sync (Auto Sync
Adjustment)
Selectable
items Description
On Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
Off Auto Sync adjustment is not
automatically performed.
Auto Sync adjustment is also performed by
pressing AUTO SYNC.
The Auto Sync adjustment may take some
time to complete, depending on the image of
the computer connected to the projector.
When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
adjustments. (See page 44.)
•
•
•
Note
2
Auto Power Off Function
Selectable
items Description
On When no input signal is detected for
more than 15 minutes, the projector will
automatically enter Standby mode.
Off The Auto Power Off function will be
disabled.
When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
Standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
•
Note
Q PRJ-ADJ2
Pict. SCR PRJ-ADJ2SIG
SEL./ADJ. ENTER END
DLP
®
Link
TM
h
Off
FUNCTION Button Input Search
STANDBY Mode Quick Start
0 min0Lamp Timer(Life) 100%
DLP
®
Link
TM
Invert
Quick Start Menu On
PRJ1
All Reset
9
0
3 Auto Restart Function
Selectable
items Description
On
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
Off The projector does not turn on
automatically when the power cord is
plugged into the AC outlet or the
breaker switch is turned on.
4 Speaker Setting
Selectable
items Description
On The audio signal is output from the
internal speaker.
Off The audio signal is not output from the
internal speaker.
5
Selecting the Transmission
Speed (RS-
232C)
Make sure that both the projector and
computer are set for the same baud rate.
Selectable
items Description
9600bps
38400bps
115200bps
Transmission speed is slow.
Transmission speed is rapid.

51
Useful
Features
8 Keylock Function
Use this function to lock the operation buttons
on the projector.
This function can be set using either the menu
screen or ENTER on the projector.
a
Setting with the menu screen
Selectable
items Description
On All buttons on the projector, except
STANDBY/ON, are locked.
Off Turns off the Keylock function.
a
Setting with the projector buttons
Locking the Operation Buttons
1 Hold down ENTER on the
projector for about 5 seconds
while the projector is being
turned on.
The Keylock function screen is displayed.
Use this function to lock the operation buttons
on the projector.
(Except STANBY/ON button)
Note: You can release the keylock by holding down
ENTER on the projector for about 5 seconds.
PRJ - ADJ1
Return
On
SEL. ENTER END
2
Select “On”, then press
ENTER
.
On-screen display
The Keylock function does not affect the
operation with the remote control buttons.
You cannot use the Keylock function while the
projector is warming up.
•
•
•
1
2
Taking the Keylock Off
Hold down ENTER on the projector for about
5 seconds.
On-screen display
Info
Even when Keylock function is set to “On”,
STANDBY/ON on the projector can be used
to turn on and off the power.
Keylock cannot be set while the projector is:
displaying the “Setup Guide” or “Menu”
screens, in Standby mode, warming up,
changing input signals, operating the Auto
Sync or Input Search function, in Freeze
mode or on the “System Lock” screen during
warming up.
•
•
9 Selecting the Quick
Start Menu
Selectable items Description
On Pressing MENU displays the
Quick Start Menu screen.
Off Pressing MENU displays the
Complete Menu screen.
0 Setting the FUNCTION
Button Operation
You can assign one of the following functions
to the FUNCTION button on the remote con-
trol. The assigned function can be performed
by just pressing FUNCTION.
Selectable items Description
Input Search Automatically searches for and
switches to the appropriate Input
mode.
Audio Mute For temporarily turning off the
sound. Press FUNCTION again
to turn on the sound
Image Shift For moving the projected image
vertically. (See page 46.)
Signal Info Input signal information is
displayed.
Menu operation n Page 39

58
4 Remove the lamp unit.
Loosen the securing screw from the lamp
unit. Hold the lamp unit and pull it in the
direction of the arrow. At this time, keep
the lamp unit horizontal and do not tilt it.
5 Insert the new lamp unit.
Press the lamp unit fi rmly into the lamp unit
compartment. Fasten the securing screws.
6 Replace the lamp unit cover.
Align the tab on the lamp unit cover
(1) and close it (2). Then tighten the user
service screw ( ) to secure the lamp unit 3
cover.
Info
If the lamp unit and lamp unit cover
are not correctly installed, the power
will not turn on, even if the power
cord is connected to the projector.
•
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or
explode.
•
1 Connect the power cord and
open the lens shutter fully.
Plug the power cord into the AC socket of
the projector.
2 Reset the lamp timer.
While simultaneously holding down
MENU, and ENTER R on the projector,
press STANDBY/ON on the projector and
keep all four buttons pressed down until
the lamp indicator starts blinking green.
“LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
•
•
•
•
•
•
4
Securing
screw
Securing
screw
5
6
AC socketAC socket
1
ENTER button
MENU button
R button
STANDBY/ON
button
ENTER button
MENU button
R button
STANDBY/ON
button
2
Regarding the Lamp (Continued)

64
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second start up time)
C.M.S. Setting On C M C S _ _ 1 1 OK or ERR ERR
Off C M C S _ _ 0 0 OK or ERR ERR
C.M.S. Hue Red C M H R _***OK or ERR ERR
Yellow C M H Y _***OK or ERR ERR
Green C M H G _***OK or ERR ERR
Cyan C M H C _***OK or ERR ERR
Blue C M H B _***OK or ERR ERR
Magenta C M H M _***OK or ERR ERR
Reset C M R E ___2OK or ERR ERR
Saturation Red C M S R _***OK or ERR ERR
Yellow C M S Y _***OK or ERR ERR
Green C M S G _***OK or ERR ERR
Cyan C M S C _***OK or ERR ERR
Blue C M S B _***OK or ERR ERR
Magenta C M S M _***OK or ERR ERR
Reset C M R E ___3OK or ERR ERR
Value Red C M V R _***OK or ERR ERR
Yellow C M V Y _***OK or ERR ERR
Green C M V G _***OK or ERR ERR
Cyan C M V C _***OK or ERR ERR
Blue C M V B _***OK or ERR ERR
Magenta C M V M _***OK or ERR ERR
Reset C M R E ___4OK or ERR ERR
C.M.S. All Reset C M R E ___1OK or ERR ERR
Clock -150 – +150 I N C L * * * * OK or ERR ERR
Phase -30 – +30 I N P H _***OK or ERR ERR
H-position -150 – +150 I A H P * * * * OK or ERR ERR
V-position -60 – +60 I A V P _***OK or ERR ERR
Fine Sync Adjustment Reset I A R E ___1OK or ERR ERR
Image Shift -96 – +96 (XGA)/-75 – +75
(SVGA)L N D S _***OK or ERR ERR
Overscan On O V S N ___1OK or ERR ERR
Off O V S N ___0OK or ERR ERR
OSD Display On I M D I ___1OK or ERR ERR
Off I M D I ___0OK or ERR ERR
Video System Auto M E S Y ___1OK or ERR ERR
PAL M E S Y ___2OK or ERR ERR
SECAM M E S Y ___3OK or ERR ERR
NTSC4.43 M E S Y ___4OK or ERR ERR
NTSC3.58 M E S Y ___5OK or ERR ERR
PAL-M M E S Y ___6OK or ERR ERR
PAL-N M E S Y ___7OK or ERR ERR
PAL-60 M E S Y ___8OK or ERR ERR
Background Logo I M B G ___1OK or ERR ERR
Blue I M B G ___3OK or ERR ERR
None I M B G ___4OK or ERR ERR
Eco+Quiet On T H M D ___1OK or ERR ERR
Off T H M D ___0OK or ERR ERR
Auto Sync On A A D J ___1OK or ERR ERR
Off A A D J ___0OK or ERR ERR
Auto Power Off On A P O W ___1OK or ERR ERR
Off A P O W ___0OK or ERR ERR
Auto Restart On A R E S ___1OK or ERR ERR
Off A R E S ___0OK or ERR ERR
STANDBY Mode Quick Start M O U T ___1OK or ERR ERR
Eco M O U T ___0OK or ERR ERR
PRJ Mode Reverse On I M R E ___1OK or ERR ERR
Off I M R E ___0OK or ERR ERR
Invert On I M I N ___1OK or ERR ERR
Off I M I N ___0OK or ERR ERR
RS-232C Specifi cations and Commands
(Continued)
Product specificaties
Merk: | Sharp |
Categorie: | Beamer |
Model: | XR-50S |
Heb je hulp nodig?
Als je hulp nodig hebt met Sharp XR-50S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Beamer Sharp

20 Februari 2025

17 December 2024

15 Mei 2024

9 Juni 2023

7 Juni 2023

26 Mei 2023

26 Mei 2023

23 Mei 2023

17 Mei 2023

15 Mei 2023
Handleiding Beamer
- Beamer Philips
- Beamer HP
- Beamer Sony
- Beamer Samsung
- Beamer Xiaomi
- Beamer Casio
- Beamer Panasonic
- Beamer Epson
- Beamer LG
- Beamer Asus
- Beamer Canon
- Beamer JVC
- Beamer Medion
- Beamer Toshiba
- Beamer Yamaha
- Beamer Acco
- Beamer Acer
- Beamer Aiptek
- Beamer Anker
- Beamer AOpen
- Beamer ASK Proxima
- Beamer Auna
- Beamer Barco
- Beamer Bauer
- Beamer BenQ
- Beamer Blaupunkt
- Beamer D-Link
- Beamer Dell
- Beamer Easymaxx
- Beamer Eiki
- Beamer Elmo
- Beamer Emtec
- Beamer GPX
- Beamer Hama
- Beamer Hisense
- Beamer Hitachi
- Beamer Ibm
- Beamer InFocus
- Beamer Ion
- Beamer Klarstein
- Beamer Kodak
- Beamer Kogan
- Beamer La Vague
- Beamer Leica
- Beamer Lenco
- Beamer Lenovo
- Beamer Livoo
- Beamer Marantz
- Beamer Maxell
- Beamer Mitsubishi
- Beamer Nebula
- Beamer Nec
- Beamer PLUS
- Beamer Polaroid
- Beamer Pyle
- Beamer RCA
- Beamer Reflecta
- Beamer Renkforce
- Beamer Ricoh
- Beamer Salora
- Beamer Sanyo
- Beamer Showtec
- Beamer Smart
- Beamer Smartwares
- Beamer Speaka
- Beamer Steinel
- Beamer Strong
- Beamer Technaxx
- Beamer Viewsonic
- Beamer Vivitek
- Beamer Vogels
- Beamer XGIMI
- Beamer ZTE
- Beamer Odys
- Beamer OK
- Beamer Oki
- Beamer Optoma
- Beamer Overmax
- Beamer 3M
- Beamer Krüger And Matz
- Beamer Naxa
- Beamer Steren
- Beamer Eurolite
- Beamer Prixton
- Beamer Planar
- Beamer Dukane
- Beamer Yaber
- Beamer Mimio
- Beamer Da-Lite
- Beamer Adj
- Beamer Dahua Technology
- Beamer Derksen
- Beamer Celly
- Beamer Promethean
- Beamer Stairville
- Beamer Laserworld
- Beamer Beghelli
- Beamer Cameo
- Beamer Tzumi
- Beamer EKO
- Beamer MicroVision
- Beamer Elite Screens
- Beamer Celexon
- Beamer Fun Generation
- Beamer Christie
- Beamer Futurelight
- Beamer Varytec
- Beamer Ultimea
- Beamer Dracast
- Beamer Dream Vision
- Beamer Knoll
- Beamer DTS
- Beamer Touchjet
- Beamer Boxlight
- Beamer AAXA Technologies
- Beamer Miroir
- Beamer Vankyo
- Beamer AWOL Vision
- Beamer Smart Tech
- Beamer Atlantis Land
- Beamer KickAss
- Beamer Microtek
- Beamer VAVA
- Beamer Panamorph
- Beamer Mirabella Genio
Nieuwste handleidingen voor Beamer

25 Februari 2025

20 Februari 2025

20 Februari 2025

10 Februari 2025

30 Januari 2025

30 Januari 2025

30 Januari 2025

30 Januari 2025

30 Januari 2025

30 Januari 2025