Sharp LC-32D7U Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Sharp LC-32D7U (101 pagina's) in de categorie Televisie. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/101
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA DE CRISTAL LIQUIDO
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACIÓN
LC-37D7U
LC-32D7U
LC-26D7U
ENGLISH
ESPAÑOL FRANÇAIS
ENGLISH
LC-37D7U
LC-32D7U
LC-26D7U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrow-head
symbol, within an equilateral
triangle, is intended to alert the user
to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within a
triangle is intended to alert the user
to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the product.
IMPORTANT:
To aid reporting in case of loss or theft, please record
the TV’s model and serial numbers in the space
provided. The numbers are located at the rear of the
TV.
Model No.:
Serial No.:
• The illustrations and on-screen displays in this operation
manual are for explanation purposes and may vary slightly
from the actual operations.
• Menu items that are not selectable are grayed out.
• The examples used throughout this manual are based on
the LC-32D7U model.
2
IMPORTANT INFORMATION
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user’s authority to operate this equipment.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.”
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these
materials may be regulated due to environmental considerations. For disposal or recycling information, please contact
your local authorities or the Electronic Industries Alliance: www.eia.org
CAUTION:
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, BRACKET, OR
TABLE. THE PRODUCT MAY FALL CAUSING SERIOUS PERSONAL INJURY AND SERIOUS
DAMAGE TO THE PRODUCT. USE ONLY WITH A CART, STAND, TRIPOD, BRACKET, OR TABLE
RECOMMENDED BY THE MANUFACTURER OR SOLD WITH THE PRODUCT. FOLLOW THE
MANUFACTURER’S INSTRUCTIONS WHEN INSTALLING THE PRODUCT AND USE MOUNTING
ACCESSORIES RECOMMENDED BY THE MANUFACTURER. A PRODUCT AND CART
COMBINATION SHOULD BE MOVED WITH CARE. QUICK STOPS, EXCESSIVE FORCE, AND
UNEVEN SURFACES MAY CAUSE THE PRODUCT AND CART COMBINATION TO OVERTURN.
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
DECLARATION OF CONFORMITY
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-37D7U
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-32D7U
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-26D7U
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TEL: 1-800-BE-SHARP
For Business Customers: URL http://www. sharpusa. com
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use
shielded cables and connectors for connections.
3
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years
of trouble-free operation of your product, please read the Important Safety Instructions carefully
before using this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if
improperly handled. This product has been engineered and manufactured with the highest priority on safety. However,
improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following
instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of
your Liquid Crystal Television, please read the following precautions carefully before using the product.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
15) Power Sources — This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local
power company. For products intended to operate from battery power, or other sources, refer to the operating
instructions.
16) Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17) Object and Liquid Entry — Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
18) Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance – this indicates a need for service.
19) Replacement Parts — When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20) Safety Check — Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
21) Wall or ceiling mounting — When mounting the product on a wall or ceiling, be sure to install the product
according to the method recommended by the manufacturer.
4
IMPORTANT SAFETY INSTRUCTIONS
• Water and Moisture — Do not use this product near water – for example, near a bath tub,
wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the
like.
• Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the
product on an unstable base can cause the product to fall, resulting in serious personal
injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold with the product. When mounting the product on
a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware
recommended by the manufacturer.
• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do
not cover or block these vents and openings since insufficient ventilation can cause
overheating and/or shorten the life of the product. Do not place the product on a bed, sofa,
rug or other similar surface, since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in an enclosed place such as a
bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are
followed.
• The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when
the product is dropped or applied with impact. Be careful not to be injured by broken glass
pieces in case the panel breaks.
• The Liquid Crystal panel is a very high technology product with 3,147,264 thin film transistors, giving you fine picture
details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note
that this does not affect the performance of your product.
Precautions when transporting the TV
When transporting the TV, never carry it by holding onto the speaker. Be sure to always
carry the TV by two people holding it with two hands—one hand on each side of the Display.
• Heat — The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
• Lightning — For added protection for this television equipment during a lightning
storm, or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna. This will prevent damage to the
equipment due to lightning and power-line surges.
• Power Lines — An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or circuits as contact
with them might be fatal.
• Selecting the location — Select a place with no direct sunlight and good ventilation.
5
IMPORTANT SAFETY INSTRUCTIONS
• Outdoor Antenna Grounding — If an outside antenna is connected to the television equipment, be sure the antenna
system is grounded so as to provide some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of
the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the
grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC —NATIONAL ELECTRICAL CODE
• To prevent fire, never place any type of candle or flames on the top or near the TV
set.
• To prevent fire or shock hazard, do not expose this product to dripping or splashing.
No objects filled with liquids, such as vases, should be placed on the product.
• To prevent fire or shock hazard, do not place the AC power cord under the TV set
or other heavy items.
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• Use a soft cloth and gently wipe the surface of the TV panel. Using a hard cloth
may scratch the panel surface.
• Use a soft damp cloth to gently wipe the panel when it is really dirty.
(It may scratch the panel surface when wiped strongly.)
• If the panel is dusty, use an anti-static brush, which is commercially available, to
clean it.
• To protect the panel, do not use a dirty cloth, liquid cleaners or chemical cloth to
clean it, such materials may damage the panel surface.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
6
QUICK REFERENCE
STOP! To safely remove the AQUOS television from the box
It's best to use 2 people to remove the AQUOS television for stability.
1. Use the cardboard holders on either side of the AQUOS television to remove it
from the box.
2. Remove the cardboard; however, keep the wrapping on the AQUOS television to
protect it while moving.
3. Lift onto installation location as the diagram illustrates.
Ventilation & Cleaning Tips
Keep your AQUOS television in a well ventilated area and make sure not to place it by a
heat source or use near water. The AQUOS television is designed for AC use only and
should be used with supplied AC cord.
Clean the screen by spraying a soft lint free cloth with water to lightly moisten. Gently
wipe and avoid pressing on the screen. To clean the outer cabinet, use the same
method. Do not use liquid or aerosol cleaners.
The screen is glass and can be scratched or broken when dropped or impacted.
QUICK INSTALLATION TIPS
1. Facing the back of the AQUOS television, remove
the terminal cover.
Press down the
upper hooks to
remove the cover
toward you.
2. Attach your antenna to the back of the TV. (See
page 16.)
3. Connect the AC plug for the AQUOS television
into the wall outlet.
5. How to turn on the AQUOS television for the first
time.
A) Press POWER on AQUOS television.
POWER
B) POWER indicator on the front of the AQUOS
television lights blue.
CAUTION
•TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH UN-INSULATED PARTS OF ANY CABLES WITH
THE AC CORD CONNECTED.
4. Bundle the cords properly with a cable clamp and
cable tie, and close the terminal cover.
NOTE
• Speaker cannot be detached from the TV.
• TV angle cannot be adjusted.
POWER indicator
7
QUICK REFERENCE
IMPORTANT:
The POWER indicator on the AQUOS television should light blue indicating you have power to the AQUOS
television.
If the POWER indicator on the AQUOS television still does not light up, press TV POWER
on the remote control to turn the power on.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE AQUOS TELEVISION FROM THE OUTLET AND REPEAT
THE INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT US AT 1-800-BE-SHARP.
Please refer to the BASIC ADJUSTMENT SETTINGS SECTION for EZ setup and basic channel setup functions
and USING EXTERNAL EQUIPMENT SECTION for other device connections (DVD, VCR, AUDIO, etc) in your
AQUOS operation manual.
1Open the battery cover. 2Insert two “AAA” size batteries
(supplied with the product).
• Place the batteries with their terminals
corresponding to the ( ) and (e f)
indications in the battery compartment.
3Close the battery cover.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with
skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove batteries from it.
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.
8
QUICK REFERENCE
TV GUIDE ON SCREEN™ QUICK SETUP SHEET
Once you set up the TV according to this operation manual, you are ready to set up TV Guide On Screen!
Note: TV Guide On Screen™ interactive program guide supports cable-ready, cable box and digital cable
services as well as over-the-air broadcast. It does not provide listings for satellite services.
After completing the TV’s initial setup, you see the TV
Guide On Screen Setup Welcome Screen.
Note: If TV Guide On Screen is not setup, pressing TV
GUIDE Welcome while watching TV will display the
Screen.
Follow the on-screen instructions
If you previously skipped TV Guide On Screen setup,
you see the Reminder Screen.
Note: If you press and the screen does notENTER
change, make sure that the batteries in the remote are
properly installed.
If you need to control a cable box and/or a VCR,
complete steps 1 through 3. If not, go to step 4.
1
2
Find and Connect the included G-LINK cable
into the G-LINK terminal.
Find the VCR and Cable Box IR Sensors.
To control recording, find the VCR's IR sensor.
1Turn the VCR off.
2Hold the VCR remote so that it touches the
front of the VCR (Figure 1).
3Move the remote across the front while
pressing POWER (Figure 2). (You must press
and release the power button each time you
move the remote; holding down the button will
not work).
4When the VCR powers on, you have found
the sensor.
5Remember the location of the sensor, and go
to step 3.
If you have a cable box, repeat this procedure
using the cable box and its remote, and then
go to step 3.
G-LINK cable with
Double-Sided Tape
Place the G-LINK cable(s)
To control a VCR, place one of the G-LINK
cables underneath the VCR approximately 1
inch in front of the sensor you found in step 2.
If you have a cable box, place the other G-
LINK cable approximately 1 inch in front of
the sensor you found in step 2.
Use the double-sided tape to secure each
G-LINK cable.
4
3
Use the TV remote for On-Screen Setup
1 a b c dPress / / / and ENTER to highlight an
item in a Setup screen.
2Press ENTER to select that item.
a b c d/ / /
ENTER
G-LINK cable
Figure 1
Correct Incorrect
Figure 2
G-LINK
cable
This end is connected to the TV as
shown in step 1.
1 inch
VCR
or
Cable Box
G-LINK wand
9
If the answer is “YES”, you
next see the screen in step
11.
If the answer is “NO”, you
are returned to step 5 from
where you can change any
incorrect information by
repeating the Setup process.
On-Screen Setup
• TV Guide uses setup information to provide TV listings and lineups.
QUICK REFERENCE
5
The first two screens ask you about your
location.
Follow the on-screen
instructions.
Press c d/ to move the
highlight.
Press 0-9 or a b/ to enter
a ZIP Code or Postal
Code.
6
These screens ask you about cable.
If the answer is “YES”, you
next see a screen about a
cable box.
If the answer is “NO”, you
next see the screen in step
7 which asks about an
antenna connection.
If the answer is “YES”, you
are directed through
additional screens, which
include selecting the input
used on the TV for the
cable box and verifying the
cable box and verifying the
cable box brand. When successfully completed, you
next see the screen in step 7 which asks about an
antenna connection.
•Please refer to the note on step 4 in page 21 for
details.
If the answer is “NO”, you next see the screen in step
7 which asks about an antenna connection.
7
This screen asks you about an antenna
connection.
If the answer is “YES”, you
may see an additional
screen to select the input.
Then you next see the
screen in step 8 about
confirming your basic
settings.
If the answer is “NO”, you next see the screen in step
8 about confirming your basic settings.
Important: If you selected that you do not
have cable service connected to this TV in
the previous screens, you must select “YES”
in this screen to receive a channel lineup and
listings.
8
This screen asks you if the settings are
correct, so far.
If the answer is “YES”, you
next see an information
screen and then the screen
in step 9 which asks about
a VCR.
If the answer is “NO”, you
are returned to step 5, from
where you can change any incorrect information by
repeating the Setup process.
9
This screen asks you about a VCR.
If the answer is “YES”, you
are directed through
additional screens, which
include selecting and
verifying the VCR brand.
When successfully
completed, you next see
the screen in step 10 which asks about confirming all
of your settings.
If the answer is “NO”, you next see the screen in step
10 which asks about confirming all of your settings.
10
This screen asks you to confirm that the
settings are correct.
This screen indicates you have successfully
completed setup for TV Guide On Screen.
Important: Power off your
recorder overnight and if
you have a cable box,
leave it on.
Within 24 hours, you will
begin to receive TV
program listings.
Note: If you have a cable box, it is normal for
the TV to switch channels on the cable box
while the unit is setting up. DO NOT interfere
with the process. If you want to resume TV
viewing and stop the TV from changing
channels, you need to power on the TV.
12
This screen gives helpful information about
TV Guide On Screen.
Congratulations, you are
done!
In the United States, TV GUIDE and other related marks
are registered marks of Gemstar-TV Guide
International, Inc. and/or one of its affiliates. In Canada,
TV GUIDE is a registered mark of Transcontinental Inc.,
and is used under license by Gemstar-TV Guide
International, Inc.
11
10
Contents
IMPORTANT INFORMATION ……………………… 1
DEAR SHARP CUSTOMER ………………………… 3
IMPORTANT SAFETY INSTRUCTIONS …………… 3
QUICK REFERENCE ………………………………… 6
Contents …………………………………………… 10
Trademarks ………………………………………… 11
COPYRIGHT AND LICENSE NOTICE ………… 11
PATENT NOTICE …………………………………… 11
Supplied accessories …………………………… 12
Part names ………………………………………… 13
TV (Front) ……………………………………… 13
TV (Rear) ……………………………………… 14
Remote control unit …………………………… 15
Preparation ………………………………………… 16
Using the remote control unit ………………… 16
Cautions regarding remote control unit … 16
Antennas ……………………………………… 16
Watching TV ……………………………………… 17
Turning on the power ………………………… 17
Turning off the power ………………………… 17
Initial setup ……………………………………… 18
Using the TV Guide On Screen™
(Interactive Program Guide) ……………… 19
TV Guide On Screen Initial setup …………… 20
Using TV Guide On Screen …………………… 24
Program recording using
LISTINGS function ………………………… 27
Using Reminder function ……………………… 27
Using SCHEDULE function …………………… 28
Changing system settings …………………… 31
Changing channel display …………………… 31
Changing default options …………………… 32
Changing channels-Air/Cable ……………… 34
Changing volume/sound ……………………… 35
Setting MTS/SAP stereo mode ……………… 36
Setting Digital broadcasting audio mode …… 36
Connecting Digital Cable Module …………… 37
Basic adjustment settings ……………………… 38
AV input mode menu items …………………… 38
PC input mode menu items …………………… 39
EZ setup ………………………………………… 39
Channel Setup ………………………………… 40
Antenna Setup – DIGITAL – Air ……………… 42
Standby Mode ………………………………… 42
Favorite channel setting ……………………… 43
Language setting ……………………………… 43
Picture adjustments …………………………… 44
OPC setting ………………………………… 45
C.M.S. (Color Management System) …… 45
Color temperature ………………………… 46
Black ……………………………………… 46
3D-Y/C ……………………………………… 46
Monochrome ……………………………… 47
Film Mode (3:2 pull-down) ……………… 47
I/P Setting ………………………………… 47
Sound adjustment ……………………………… 48
Dolby Virtual …………………………………… 48
Power Control ………………………………… 49
Power control for AV source ……………… 49
Power control for PC source……………… 49
Digital Setup …………………………………… 50
Video Setup ………………………………… 50
Audio Setup ……………………………… 51
Using external equipment ……………………… 52
Displaying an external equipment image …… 52
Connecting a DVD player …………………… 53
Connecting a VCR …………………………… 54
Connecting a game console
or camcorder ……………………………… 54
Connecting a Digital TV STB (Air or Cable) … 55
Connecting HDMI equipment ………………… 56
Displaying an image from HDMI
equipment ………………………………… 56
Connecting a PC ……………………………… 57
Connecting D-VHS decks/AV-HDD recorder/
Blu-ray Disc recorder (i.LINK connection)
58
About i.LINK ……………………………… 58
i.LINK connection ………………………… 58
Connecting two or more i.LINK devices … 58
Setting the Recording Mode (i.LINK) …… 59
Setting the Standby Mode (i.LINK) ……… 59
Selecting an i.LINK device ……………… 60
Disabling the TV’s operation of
an i.LINK device ……………………… 60
Deleting registered i.LINK devices ……… 60
Controlling an i.LINK device……………… 61
Automatic input switching to i.LINK …… 62
Recording digital programs
with a D-VHS deck (i.LINK)…………… 62
Recording digital programs with AV-HDD
recorder/Blu-ray Disc recorder ……… 63
Playing back using REC LIST (i.LINK) … 63
Useful adjustment settings ……………………… 64
Image position (AV input mode only) ……… 64
Moving the picture on the screen …………… 64
Auto Sync. adjustment (PC input mode only) … 65
Fine Sync. adjustment (PC input mode only) … 65
Input Select …………………………………… 66
Input Label ……………………………………… 67
Picture Flip ……………………………………… 67
AV MODE ……………………………………… 68
View mode for 4:3 Programs ………………… 68
View mode for HD Programs ………………… 68
View mode (for PC input mode) ……………… 69
Input signal (for PC input mode) …………… 70
Digital Noise Reduction ……………………… 70
Audio Only ……………………………………… 70
Output Select …………………………………… 71
Quick Shoot …………………………………… 71
Sleep Timer …………………………………… 71
Program Title Display ………………………… 72
Closed Captions and Digital Closed
Captions …………………………………… 73
Caption Size ……………………………… 74
Font Style …………………………………… 74
Foreground Color ………………………… 75
Foreground Opacity ……………………… 75
Background Color ………………………… 75
Background Opacity ……………………… 76
Character Edge …………………………… 76
Secret number setting for parental control
(AV input mode only) ……………………… 77
Parental control (setting V-CHIP level) ……… 79
How to temporarily release
the V-CHIP BLOCK ……………………… 83
Reactivating the temporarily released
V-CHIP BLOCK …………………………… 83
11
Contents
COPYRIGHT AND LICENSE NOTICE
• It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that
prior permission be obtained from copyright owners whenever necessary.
• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property
rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and
other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is
prohibited. U. S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; 5,315,448; 6,381,747; and 6,516,132.
• This digital television is capable of receiving analog basic, digital basic and digital premium cable television programming
by direct connection to a cable system providing such programming. A security card provided by your cable operator is
required to view encrypted digital programming. Certain advanced and interactive digital cable services such as video-
on-demand, a cable operator's enhanced program guide and data-enhanced television services may require the use of
a set-top box. For more information call your local cable operator.
• The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of
its affiliates.
Trademarks
• Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol
are trademarks of Dolby Laboratories.
• Manufactured under license from BBE Sound, Inc.
Licensed by BBE Sound, Inc. under USP4638258, 5510752 and 5736897. BBE and BBE symbol are registered
trademarks of BBE Sound, Inc.
• “HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.”
• CableCARD™ is a trademark of Cable Television Laboratories, Inc.
Other viewing options …………………………… 84
Viewing information of the program ………… 84
Picture and still image ………………………… 84
Presetting remote control function …………… 85
Appendix ………………………………………… 90
Removing the stand …………………………… 90
Setting the TV on the wall …………………… 90
Troubleshooting ………………………………… 91
Troubleshooting-TV Guide On Screen ……… 92
Troubleshooting-Digital broadcasting ……… 93
PC compatibility chart ………………………… 93
RS-232C port specifications ………………… 94
Specifications ………………………………… 96
Optional accessories ………………………… 96
Dimensional drawings …………………………… 97
• In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International,
Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used
under license by Gemstar-TV Guide International, Inc.
PATENT NOTICE
The TV Guide On Screen system is protected by one or more of the following issued United States patents
6,498,895, 6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.
12
Supplied accessories
Make sure the following accessories are provided with the product.
NOTE
• Always use the AC cord supplied with the LCD-TV.
Remote control unit (g1)
Page 7
“AAA” size battery (g2)
Page 7 Page 6
AC cord (g1)
Operation manual (g1)
Cable clamp (g1)
Page 6
Cable tie (g1)
Page 6
G-LINK cable ( 1)g
Page 8
13
Part names
POWER indicatorOPC sensor
TV (Front)
POWER button
INPUT button*
Volume buttons (VOLl k / ) Channel
buttons**
(CHs r/ )
Remote control sensor
*OPC: Optical Picture Control
(See page 45.)
*DL: DownLoad
OPC/DL indicator
* INPUT button works as
ENTER in TV Guide On
Screen
** Channel buttons work as
a b/ in TV Guide On
Screen
NOTE
• See page 17 for status indicator.
14
Part names
TV (Rear)
*Press RESET if the TV cannot return to its original state after performing various operations.
• AV MODE resets to DYNAMIC (Fixed)
• TV channel returns to initial channel (Air:2ch, Cable:1 or 2ch)
• Audio setting initializes
• Dolby Virtual resets to off
• Image position initializes
** Press SYSTEM RESET if the TV does not operate after starting up.
NOTE
• Pressing RESET will not work if the TV is in standby mode.
• Pressing RESET will not delete channel preset or secret number. See page 78 for clearing the secret number when you
know it. See page 98 for initializing to the factory preset values when you forget your secret number.
RESET*
INPUT 3
terminals
SYSTEM
RESET**
ANALOG IN
terminal
AC INPUT terminal
RS-232C terminal
INPUT 2 terminals
INPUT 1
terminals
INPUT 5 terminals
INPUT 4 terminal
MONITOR OUT/
REC OUT terminals
i.LINK terminals
CableCARD™ slot
DIGITAL AUDIO
OUTPUT terminal
G-LINK terminal
DIGITAL AIR IN
terminal
DIGITAL CABLE
IN terminal
15
Part names
Remote control unit
2
3 18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1 17
4
5
6
7
8
9
11
12
13
14
15
16
10
6 AIR: Receives air signal.
7 CABLE: Receives cable signal.
8 VOL kk
kkk/ll
ll
l: Sets the volume. (See page 35.)
9 Virtual: Selects Virtual Dolby Surround settings. (See
page 35.)
10 INFO:
Displays the program information screen. (See page 84.)
11 RECORD:
Records the program to equipment (capable of
recording). (See page 27.)
In TV Guide On Screen, initiates the recording process.
12 EXIT: Turns off the menu screen and TV Guide On
Screen.
13 FAVORITE CH
A B C, , , D: Selects four preset favorite channels in four
different categories. (See page 43 for details.)
While watching, you can toggle the selected channels
by pressing A, B, C and D.
DAY l/DAY k:In TV Guide On Screen, moves forward
or backward in 24 hour increments in the listing grid.
14 AUDIO: Selects the MTS/SAP or the audio mode during
multi-channel audio broadcasts. (See page 36.)
15 SLEEP: Sets the sleep timer. (See page 71.)
16 i.LINK: Displays the i.LINK panel. (See page 60.)
17 FUNCTION: Switches the remote control for TV, CBL/
SAT, VCR, DVD and AUDIO operation. Indicator lights
up for the current mode. (See pages 85 to 88 for details.)
* To enter the code registration mode, you need to press
FUNCTION DISPLAY and at the same time.
18 : When pressed all buttons on the remote control unit
will light. The lighting will turn off if no operations are
performed within about 5 seconds. This button is used
for performing operations in low-light situations.
19 VIEW MODE: Selects the screen size. (See pages 68
and 69.)
20 ENT: Enters a channel selection when choosing with
the 0-9 buttons.
21 FLASHBACK: Returns to the previous channel or
external input mode. (See page 34.)
22 INPUT: Selects a Liquid Crystal Television input source.
(TV, CableBox, INPUT 1, INPUT 2, INPUT 3, INPUT 4,
INPUT 5, i.LINK) (See pages 52 and 66.)
If the CableBox is set up in the TV Guide On Screen
setting menu, the CableBox option appears.
23 CH rrrrr/ssss
s: Selects the channel.
In the TV Guide On Screen, moves one page up or one
page down in the LISTINGS grid.
24 MUTE: Mutes the sound. (See page 35.)
25 TV GUIDE: Displays TV Guide On Screen.
26 MENU: Displays the menu screen.
27 a b c d/ / / /ENTER: Selects a desired item on the
screen.
28 RETURN: Returns to the previous menu screen.
29 FREEZE: Sets the still image. Press again to return to
normal screen. (See page 84.)
30 CC: Displays captions when receiving closed-caption
signals. (See page 73.)
31 EDIT: Registers favorite channel.
32 AV MODE: Selects an audio or video setting. (See
page 68.) (AV mode: STANDARD, MOVIE, GAME,
USER, DYNAMIC (Fixed), DYNAMIC. PC mode:
STANDARD, USER.)
1 TV POWER: Switches the Liquid Crystal Television
power on or enters Standby mode. (See page 17.)
2 DISPLAY: Displays the channel information.
3 SOURCE POWER: Turns the power of the external
equipment on and off.
4 External equipment operational buttons: Operates
the external equipment.
5 0 – 9/• (DOT): Sets the channel.
16
Preparation
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor on
the TV. Objects between the remote control unit and the remote control sensor
may prevent proper operation.
Cautions regarding remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not place
in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight.
The heat may cause deformation of the remote control unit.
• The remote control unit may not work properly if the remote control sensor on
the TV is under direct sunlight or strong lighting. In such cases, change the
angle of the lighting or the TV, or operate the remote control unit closer to the
remote control sensor.
300-ohm twin-lead (flat)
300-ohm twin-lead
75-ohm coaxial cable (round)
75-ohm coaxial cable
Cable TV lead-In
or
IN OUT
300-ohm
twin-lead
VHF
ANTENNA
UHF
ANTENNA
Combiner
(commercially
available)
or
Home Antenna
terminal (75-ohm)
300/75-ohm adapter
(commercially available)
Coaxial cable
(commercially
available)
signal splitter
(commercially
available)
Cable without a CATV
converter
Combination
VHF/UHF antenna
Separate VHF/UHF
antenna
Connecting Antenna Cable
1. A 75-ohm system is generally a round cable with F-type
connector that can easily be attached to a terminal without
tools (Commercially available).
2. A 300-ohm system is a flat “twin-lead” cable that can be
attached to a 75-ohm terminal through a 300/75-ohm
adapter (Commercially available).
F-type connector
75-ohm coaxial cable (round)
300-ohm twin-lead cable (flat)
F-type connector
75-ohm coaxial cable
When connecting the RF cable to the TV set, do not tighten
F-type connector with tools.
If tools are used, it may cause damage to your TV set.
(The breaking of internal circuit, etc.)
F-type connector should be finger-tightened only.
NOTICE
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the TV set.
Depending on your reception environment,
either CABLE IN or AIR IN may be used, or
both CABLE IN and AIR IN may be used.
17
“Off” is selected in OPC setting
“On” or “On:Display” is selected in OPC setting
CableCARD is downloading data
TV Guide On Screen system is downloading data
Timer recording (in TV Guide On Screen system) is in
progress
TV Guide On Screen system is preparing to start timer
recording or display reminder screen
Watching TV
Simple operations for watching a TV program
POWER
Turning on the power
TV status indicator (POWER)
POWER indicator
Press POWER on the TV or press TV POWER on the remote
control.
• POWER indicator (Blue): The TV is on. (After a few seconds, a window
appears with sound.)
NOTE
• The initial setup starts when the TV powers on for the first time. If the TV
has been turned on before, the EZ setup will not be invoked. See page
39 for performing EZ setup from the Setup menu.
Turning off the power
Press POWER on the TV or press TV POWER on the remote
control.
• The TV enters standby mode and the image on the screen disappears.
• The POWER indicator on the TV gradually turns off.
NOTE
• If you are not going to use this TV for a long period of time, be sure to
remove the AC cord from the power outlet.
CAUTION
• Please do not unplug the AC cord when the OPC/DL indicator
is red.
TV POWER
OPC/DL indicator
Lights off
Lighting (Green)
Lighting (Red)
Lighting (Red)
Lighting (Red)
Lighting (Red)
ON
OFF/Standby
Lighting (Blue)
Lights off
TV status indicator (OPC/DL)
*OPC: Optical Picture Control
*DL: DownLoad
18
Watching TV
Initial setup
When you turn on the TV for the first time, it will automatically memorize the broadcasting channels where you
live. Perform the following steps before you press TV POWER on the remote control unit.
1. Insert the batteries into the remote control unit. (See page 7.)
2. Connect the antenna cable to the TV. (See page 16.)
3. Plug in the AC cord to the AC outlet. (See page 6.)
2
CH Search
ANALOG [ ]25 [ ]20FoundAir
CH Search
DIGITAL [ ]25 [ ]20FoundAir
2
Air ANALOG
Audio : MONO
Language setting
Select from among 3 languages: English,
French and Spanish.
Press a b/ to select the desired language
listed on the screen, and then press ENTER.
Antenna setting
Make sure what kind of connection is made with
your TV.
Press c d/ to select “Yes” for ANALOG, then press b
to move down.
Press c d/ to select “Yes” for DIGITAL (Air), then press
b to move down.
Press c d/ to select “Yes” for DIGITAL (Cable), and
press b to move down.
Select “Search Start”, and then press ENTER.
• This operation makes the TV search for both ANALOG,
DIGITAL (Air) and DIGITAL (Cable) channels.
ANALOG Yes
DIGITAL (Air)
No
Yes No
DIGITAL (Cable) Yes No
Language
Standby Mode
TV Guide On Screen
Air/Cable
CH Search
Search Start
CH Search
DIGITAL [ ]25 [ ]25FoundCable
Example
NOTE
• Some items are not selectable because the antenna
setting is linked to the TV Guide On Screen setting.
• DIGITAL(Cable) setting cannot be selected when a proper
CableCARD is inserted.
Standby Mode setting
Select the standby setting. (See page 42.)
Language
Standby Mode
TV Guide On Screen
Air/Cable
CH Search
Mode 1
Mode 2
1
5
3
4
TV Guide On Screen setting
Press ENTER to continue the setting. (See page
20.)
Channel search
Channel auto search makes the TV look for
all channels viewable in the set area.
NOTE
• Make sure what kind of connection is made with your TV.
• If no channel is found, make sure what kind of connection
is made with your TV and try EZ setup again. (See page
39.)
Press c d/ to select “Air”, “Cable” for ANALOG, then
press b to move down.
Press c d/ to select “Standard”, “HRC” or “IRC” for
DIGITAL (Cable).
Press ENTER to enter the setting.
• There are 3 kinds of CATV system, including Standard,
HRC and IRC. Select the one that matches to your TV.
Mode 1: Starting TV is quick from standby.
Mode 2: Power consumption is small at the standby.
NOTE
• When the CableCARD is inserted, power consumption will
be higher.
19
Watching TV (TV Guide On Screen)
Using the TV Guide On Screen™ (Interactive Program Guide)
NOTE
• Over-the-air or cable access to stations carrying TV Guide
On Screen data is required for the TV Guide On Screen
system to operate. The data provider may elect to
discontinue the service or it may cease to be available in
your area. In either of these cases, the TV Guide On Screen
feature will not function.
Also, since the program information provided by TV Guide
On Screen system is based on your location, you will need
to run SETUP again if you move to a different ZIP or postal
code.
About the Key features of TV Guide On Screen
● LISTINGS Service
1. Displays eight days of viewers’ local program listings
and descriptions for broadcast and cable.
2. Viewers can tune to any program, schedule a
program to record, or set a reminder.
3. The Video Window lets viewers monitor the last
channel tuned while viewing program listings, or
preview channels as they page through listings.
4. Color-coded program genres help viewers quickly
identify movies, sports, and children’s programming.
● SEARCH Feature
1. Viewers can search for programs by categories such
as HDTV, movies, sports or children’s shows. Within
categories, viewers can sort by show type, such as
baseball or football.
2. Viewers can sort alphabetically, or by a keyword
such as a show title or a starring actor.
● One-touch Recording
1. To record, viewers simply highlight a program title
and then press a button on the remote control. TV
Guide On Screen will automatically record the
program.
2. Programs may be set to record one time or every
time they air.
NOTE
• A VCR or a supported i.LINK recording device is required
for one-touch recordings. If you connect a VCR, it is
recommended that you connect it according to the
instructions on pages 8 and 54.
● Reminder Feature
1. Viewers may set reminders to ensure they never
miss their favorite programs.
2. Reminders can even be set to automatically turn on
the TV when a program begins.
Video Window Service Bar
TilePanel
Ad
Channel
Logo
Info Box
Important!
The TV Guide On Screen system automatically comes
up when you turn on the LCD-TV. You can turn off this
feature by changing default options. (See page 32 for
details.)
● Screen Components
The TV Guide On Screen system is a free, on-screen
interactive television program guide (“IPG”) built into
your LCD-TV. The TV Guide On Screen system was
developed to help today’s TV viewers, overwhelmed
by myriad viewing choices, find what they want to
watch quickly and easily, directly from their TV screen.
The TV Guide On Screen system displays all the major
TV channels and programs available in the viewer’s
household.
Video Windows - displays the last TV program or the
preview of the next TV program
Service Bar - provides access to the 4 main Guide
Services(LISTINGS/SEARCH/SETUP/SCHEDULE)
Tile - displays program title
Info Box - provides information for a highlighted item
Channel Logo - identifies network
Panel Ad - displays promotional information
The screening times of the
selected programs
Names and categories of
the selected programs
Information on the
selected programs
21
Watching TV (TV Guide On Screen)
Do you have cable service connected to
this TV?
Press a b/ to select “Yes” or “No”, and then
press ENTER.
Is a cable box connected to this TV?
Press a b/ to select “Yes” or “No”, and then
press ENTER.
• If your answer is “No”, skip to step 11 on page
22.
• If your answer is “No” skip to step 12 on page
22.
3
4
Basic initial setup
Which country is your LCD-TV located in
?
Press a b/ to select the country.
1
2
Enter the ZIP code (or postal code) for your
location using the number buttons or a b/ .
Please indicate which input the cable box
is plugged into.
Press a b/ to select the input you
connected, and then press ENTER.
• To receive TV program listings in the TV Guide
On Screen system, if you select “Input 1” or
“Input 2”, please ensure your cable box is
connected to the input marked “VIDEO”, and
proceed to step 7. Do not connect your cable
box to the “COMPONENT” video of INPUT 1 or
INPUT 2, as you will not receive any TV program
listings. If you select “Analog” input, proceed
to step 6.
5
What is your TV tuned to when using the
cable box?
Press a b/ to select from “Ch 2”, “Ch 3” and
“Ch 4”, and then press ENTER.
The diagram on the screen shows the correct
way to connect the G-LINK cable from the
back of the TV to the cable box.
Make sure the G-LINK cable is properly
connected, and then press ENTER.
• Please consult your cable provider if you are
unsure.
6
7
NOTE
• To receive TV program listings in the TV Guide On Screen
system, please ensure to connect your cable box to the
input marked “VIDEO”, if you are connecting your cable
box to your TV using INPUT 1 or INPUT 2. Do not connect
the cable box to the “COMPONENT” video of INPUT 1 or
INPUT 2, as you will not receive any TV program listings
through this input.
22
Watching TV (TV Guide On Screen)
11
Do you have an antenna connected to
your TV?
Press a b/ to select “Yes” or “No”, and then
press ENTER.
• If you select “Yes”, go to the next step.
• If you selected “No” in step 3, you must connect
an antenna to your TV and select “Yes” to
receive a channel lineup and listings.
Selecting the cable box brand name.
Press a b/ to select the cable box brand,
and then press ENTER.
8
12
Are the settings correct?
Confirm the settings displayed on the screen
and press to select “Yes, end setup”a b/
or “No, repeat setup process”, and then
press ENTER.
Press ENTER to continue.
The TV Guide On Screen system will conduct
a series of tests and when the testing is
completed the next screen will be displayed
automatically.
Do not press any buttons while testing is in
progress.
Is your cable box now tuned to channel
09?
Press a b/ to select “Yes”, “No” or “Test this
code again”, and then press ENTER.
• If you select “Yes”, go to the next step.
• If you select “No”, a different code is tested in
the previous screen.
• If you select “Test this code again”, the same
code is tested again in the previous screen.
Tune your cable box to channel 02.
Make sure to leave your cable box turned
on, and then press ENTER.
10
9
• Press a b/ to view more cable box brands.
NOTE
• Please do not use the CableCARD while using cable box.
23
Watching TV (TV Guide On Screen)
The TV Guide On Screen system will conduct
a series of tests and when the testing is
completed the next screen will be displayed
automatically.
Do not press any buttons while testing is in
progress.
Did your VCR stop playing?
Press a b/ to select “Yes”, “No” or “Test this
code again”, and then press ENTER.
Are the settings correct?
Confirm the settings displayed on the screen
and press to select “Yes, end setup”a b/
or “No, repeat setup process”, and then
press ENTER.
• If you select “Yes”, go to the next step.
• If you select “No”, a different code is tested in
the previous screen.
• If you select “Test this code again”, the same
code is tested again in the previous screen.
Press ENTER to complete the SETUP.
NOTE
•
Up-to-date listings will begin loading over the next 24 hours
when your LCD-TV is powered off.(Do not unplug the AC cord.)
• It may take more than one day for all eight days of listings
to update. The guide will automatically receive updates
during the period when your LCD-TV is turned off.
• To receive your channel lineup and program listings, leave
your cable box on. Your VCR and LCD-TV should be turned
off overnight.(Do not unplug the AC cord.)
• To record a TV program, make sure your cable box is on.
Put a tape in your VCR, tune the device to the Line input,
then turn the VCR off. (Do not unplug the AC cord.)
• You must redo the TV Guide On Screen system setup if
you:
-Move your LCD-TV to a new ZIP or postal code
-Cancel cable service or change cable boxes
-Change your VCR brand or model
Turn on your VCR and insert a tape, and then
play the media on the VCR. Then press
ENTER on the remote control of your TV.
7
Press ENTER twice to watch TV.
VCR setting
Connect a VCR to your TV and use the TV Guide On
Screen system’s program listings to easily schedule
recordings using the one-touch recording feature.
Use TV Guide On Screen to control VCR?
Press a b/ to select “Yes, setup VCR control”
or “No, end setup”, and then press ENTER.
1
2
This screen shows the correct way to connect
the G-LINK cable from the back of the TV to
the recording device. Make sure the G-LINK
cable is properly connected, and then press
ENTER.
3
Selecting the VCR brand name.
Press a b/ to select the VCR brand, and
then press ENTER.
• If you select “Yes”, go to the next step.
• If you select “No”, setup will end.
4
5
6
24
Watching TV (TV Guide On Screen)
Using TV Guide On Screen
Choosing a program to watch - Using the LISTINGS
Press TV GUIDE.
1
NOTE
• The current position of the cursor is highlighted in yellow.
• To cancel the Guide screen, press TV GUIDE.
2
Press a b c d/ / / to select the program to
watch, and then press ENTER.
Basic buttons on the remote control
Description
• When watching TV, enters the Guide and
highlights a program listing.
• When in the Guide, exit the Guide without
changing channels.
• The Info Box contains information about
a program, service, ad, or provides
general help. The size of the Info Box can
be set to “Small” or “Large”, or not to be
displayed by selecting “No”. The default
size of the Info Box is “Small”. Press INFO
to cycle among “Small”, “Large” and “No”.
• Provides directional control.
• When watching TV, press to scrolla b/
through the channel list.
• Makes a selection or executes an action.
• With a currently airing program listing
highlighted, returns to normal TV viewing
and tunes to the program channel.
• With a future airing program listing
highlighted, displays a Panel menu with
viewing options.
• Shows the program listing for a different
day.
• Selects the time on the changed listing.
• Display the Options for the Guide.
• Moves one page up or one page down in
the LISTINGS grid.
Button
TV GUIDE
INFO
a b c d/ / /
ENTER
DAY l k/
c d/
MENU
PAGE r s/
(CH r s/ )
Press c d/ to highlight the desired Channel
Logo.
1
2
3
Press a b/ to select “video” and then press
c d/ to select “locked” or “unlocked”.
Press MENU to display the Listings Options.
NOTE
• The TV Guide On Screen menus shown in this manual are
for illustration purposes only. The channels, programs, and
TV Guide On Screen information illustrated in this manual
may not be available in your area. The options and features
illustrated in this manual are subject to change when
updates are downloaded from the TV Guide On Screen
service to your TV.
• The TV Guide On Screen system does not display program
listings for satellite TV systems.
Video Window Clock
Lock/Unlock Icon
Video Window
When you enter the Guide, the TV program for the
current show appears in the Video Window. The Video
Window also includes a clock display and a lock/
unlock icon to indicate the status of the Video Window.
You can set the Video Window to remain on a single
channel (locked) or change channels (unlocked) as
you navigate through Listings.
How to set the Video Window
Changes the day from within LISTINGS
• Press DAYl or DAYk to select the day you want to
check the TV program table.
● How to go to Service Bar
The service provided by TV Guide On Screen is
composed of four services: SETUP, LISTINGS,
SEARCH and SCHEDULE. To make detailed settings
for each service, it is necessary to select the service
bar and change the selected service.
Press a b/ to select “go to Service Bar”.
Press ENTER.
Press MENU to display “Service Options”.
1
2
3
25
Watching TV (TV Guide On Screen)
Searching programs
You can search for programs alphabetically, by
category - HDTV, MOVIES, SPORTS, CHILDREN,
EDUCATIONAL, NEWS, VARIETY, SERIES - or by
keyword, and the result is displayed in a list.
When the LISTINGS screen is displayed,
press MENU.
Press a b/ to select “go to Service Bar” from
the “Episode Options” menu, and press
ENTER.
1
Press c d/ to select “SEARCH” and then
press ENTER or b.
2
3
Example: Searching for a program in the
category “MOVIES”.
Press c d/ buttons to select “MOVIES”
(=Search type) and press to display theb
movies genre.
4
Press a b c d/ / / to select a genre within
“MOVIES”. (e.g.: select “ALL” and press
ENTER)
5
Repeat steps 1 to 2 in Search by category.
1
Press c d/ to select “KEYWORD”, and then
press ENTER to display the “Keyword
Search” menu.
2
● Search by keyword
Keyword Search lets you enter a word to look for, a
particular program by category or for every program
title that matches.
3
Press a b/ to select “new search”, and then
press ENTER to display the “Search
Options” menu.
4
Press a to select “category” to search, and
then press c/d to select the desired category.
5
Press b to select “enter keyword”, and then
press ENTER. Press a b c d/ / / to select a
character, and press to display it.ENTER
When complete, press to selectabcd///
“DONE” and press ENTER.
NOTE
• BKSP: Backspace
• DEL: Delete
• CLR: Clear
A list of all matching programs is displayed.
Press b to highlight the program you want
to watch, and press ENTER.
6
● Search by category
You can search for programs by specifying category
in the “Confirmation” screen.
NOTE
• Repeat the same steps for the other categories.
• When you want to record a program found during a search,
press MENU and after “Episode options” displays, carry
out “Set recording”. (See page 27.)
Press a b/ to select a program you want to
watch, and then press ENTER.
27
Watching TV (TV Guide On Screen)
Press abcd/ / / to select the program you
want to record in the LISTINGS.
1
Press MENU to display “Episode Options”.
Press a b/ to select “set recording”, and
then press to display “RecordENTER
Options”.
2
Program recording using LISTINGS
function
You can set any programs to record on a G-LINK
connected recording device (VCR) directly from the
LISTINGS for the appropriate day.
3
Press abcd/ / / to set the following items.
4
Press ENTER to highlight “schedule
recording”.
5
Press ENTER again to exit.
once/regularly/weekly/
off
on time/120 min early
... 120 min late
on time/120 min early
... 120 min late
VCR/i.LINK
Setup
items
Using Reminder function
You can set this function to remind you of the screening
times for programs from LISTINGS and of programs
you have set to record.
Using Episode Options
Press MENU to display “Episode Options”.
Press a b/ to select “set reminder”, and then
press ENTER to display “Remind Options”.
1
Press abcd/ / / to set the following items.
2
3
Press ENTER to highlight “schedule
reminder”.
4
Press ENTER again to exit.
By pressing RECORD, the program you want
to record is set to record on time. “on time”
is the default setting and can be changed.
2
Using RECORD button on the remote control
NOTE
• Each time you press , you can change the recordRECORD
frequency.
● Set recording
Press abcd/ / / to select the program you
want to record on the LISTINGS.
1
frequency
start
end
recorder
DescriptionSelectable items
Set the recording
cycle
Set the start timing of
recording
Set the end timing of
recording
Set the external
recording device
once/regularly/weekly/
off
yes/no
yes/no
on time/30 sec - 15
min early ... 30 sec -
15 min late
Setup
items
frequency
power on TV
auto tune TV
when
DescriptionSelectable items
Set the reminder cycle
When this is set to
“yes”, the TV will
automatically switch
on at the time the
reminder was set for.
When this is set to
“yes”, the channel will
be automatically
changed before the
reminder screen is
displayed.
Set the timing to
perform above two
functions
NOTE
• Device must be selected beforehand when using i.LINK
as a recording device.
28
Press MENU to display “Episode Options”.
Press a b/ to select “go to Service Bar”, and
then press ENTER.
1
Press c d/ to select “SCHEDULE”.
2
Using SCHEDULE function
The SCHEDULE is a list of programs created whenever you set a recording, or a reminder to watch a program.
You can use this list to edit or delete the reminders and recordings you have set.
Watching TV (TV Guide On Screen)
The program listings in SCHEDULE display a range of
icons and show information about the settings for each
program.
Description
Function Icon
Record
(Using
“Record
Options”)
Records the program one time.
Regularly
Records the program every time the
program airs on the same channel
and starts at the same time.
Once
Weekly
Records the program each time the
program airs on the same day of
the week, on the same channel and
starts at the same time.
Off
Keeps the program in the list but
will not record this program until the
frequency is changed.
Suspend
• The program is suspended due
to a schedule conflict. (The
program remains in Schedule.)
• Recording resumes when the
conflict no longer exists.
Remind
(Using
“Remind
Options”)
Set a program reminder one time.
Regularly
Set a program reminder every time
the program airs on the same
channel and starts at the same time.
Once
Weekly
Set a program reminder each time
the program airs on the same
channel and starts at the same time.
Off
Keeps the program in the list but
will not remind this program until the
frequency is changed.
Suspend
• The program is suspended due
to a schedule conflict. (The
program remains in Schedule.)
• Remind resumes when the
conflict no longer exists.
Press MENU to display “Schedule Options”.
1
Press c d/ to select how to sort the
SCHEDULE.
2
Sort programs
You can sort Record and Remind programs in
SCHEDULE list.
Description
Both Record and Remind programs are
intermixed and sorted by scheduled date,
with the next scheduled program at the
top.
Both Record and Remind programs are
intermixed and sorted by program title into
alphabetical order.
Sorts first Record programs and then
Remind programs, by date.
Selected item
date
title
event
Press a b/ to select “done”.
3
Daily
Indicates the program is set to
record daily (manual record setting
only).
Daily
Indicates the program is set to
remind daily (manual remind setting
only).
29
Watching TV (TV Guide On Screen)
Press a b/ to select the program for which
you want to set the reminder.
Press MENU to display “Schedule Options”.
Repeat steps 1 to 2 in Using SCHEDULE
function.
1
2
3
Edit reminder
Press a b/ to select “edit reminder”, and
then press to display “RemindENTER
Options”.
• You can change the setting items again.
Press ENTER to highlight “schedule
reminder”.
4
5
Press ENTER again to exit.
6
Press a b/ to select the program you want
to delete.
Press MENU to display “Schedule Options”.
Repeat steps 1 and 2 in Using SCHEDULE
function.
1
2
3
Delete recording
Press a b/ to select “delete recording”, and
then press ENTER.
• Confirmation screen displays.
Press a b/ to select “yes” or “no”.
4
5
Press a b/ to select the program you want
to edit.
Press MENU to display “Schedule Options”.
Repeat steps 1 to 2 in Using SCHEDULE
function.
1
2
3
Edit recording
Press a b/ to select “edit recording”, and
then press to display “RecordENTER
Options”.
• You can change the setting items again.
Press ENTER to highlight “schedule
recording”.
4
5
Press ENTER again to exit.
6
30
Press MENU to display “Remind Options”.
Press a b/ to select “new manual reminder”
and then press ENTER.
New manual reminder
Instead of setting a reminder from the program
LISTINGS, you can set a reminder manually for a
program that you want to watch or a recording you
have set.
Press ENTER to highlight “schedule
reminder”.
NOTE
• The program set to be manually reminded is listed by
channel number in the SCHEDULE.
Watching TV (TV Guide On Screen)
• “Remind Options” screen displays.
Press a b/ to select the program you want
to record.
1
Press a b/ to select “new manual recording”
and then press ENTER.
New manual recording
Aside from setting recordings using the program
LISTINGS menus, you can also define the schedule of
recordings manually by following the steps below.
• “Record Options” screen displays.
Press ENTER to highlight “schedule
recording”.
NOTE
• The program set to be manually recorded is listed by
channel number in the SCHEDULE.
5
Press ENTER again to exit.
Press ENTER again to exit.
2
3
4
Press MENU to display “Record Options”.
Press a b/ to select the program you want
to set reminder.
1
2
3
5
4
—
—
—
—
analog/digital air/
digital cable/input 1/
input 2/input 3
VCR/i.LINK
once/weekly/daily/off
Setup
items
date
start
end
channel
input
recorder
frequency
DescriptionSelectable items
Set a date to record
Set a start time to
record
Set an end time to
record
Set a channel to
record using 0–9
Set the external
recording device or
antenna source
Select a recorder you
connected
Set the recording
cycle
—
—
—
—
analog/digital air/
digital cable/input 1/
input 2/input 3
yes/no
yes/no
once/weekly/daily/off
Setup
items
date
start
end
channel
input
power on TV
auto tune TV
frequency
DescriptionSelectable items
Set a date to remind
Set a start time to
remind
Set an end time to
remind
Set a channel to
remind using 0–9
Set the external
device or antenna
source
When this is set to
“yes”, the TV will
automatically switch
on at the time the
reminder was set for.
When this is set to
“yes”, the channel will
be automatically
changed before the
reminder screen is
displayed.
Set the reminder cycle
31
Press TV GUIDE and then press MENU.
1
Press a b/ to select “go to Service Bar” in
“Episode Options”, and then press ENTER.
2
Changing system settings
After you initially complete Guide Setup, you can make
changes to System settings in the “SETUP” screen.
3
Press c d/ to select “SETUP” .
4
Press b to select “Change system settings”.
Watching TV (TV Guide On Screen)
5
Press ENTER to display the “Confirming
Your Settings” screen.
• If you want to change System settings, select
“No, repeat setup process” and then press
ENTER.
• If the setting details displayed on the screen is
correct, select “Yes, everything is correct”, and
then press ENTER.
• If the channel lineup is incorrect, select “Yes,
but my channel lineup is incorrect”, and then
press ENTER.
Changing channel display
This setting lets you edit channel information that
appears in LISTINGS.
You can set each function as follows:
1. Re-order the position the channel appears in
LISTINGS
2. Change the channel number
3. Switch a channel
•On - the channel is always displayed
•Off - the channel is never displayed
•Auto-Hide - the channel is only displayed when
program information is available
Press a b/ to select “Change channel
display”, and then press ENTER.
1
Press ENTER to display the “Grid Options”
screen.
2
3
Press abcd/ / / to set the following items.
Description
off/on/auto-hide
Air/Cable/cable box
Set the channel number you want to display
Set the channel display position
Selected item
channel
service
tune channel
position
Press a b/ to select “done”, and then press
ENTER to exit.
4
Repeat steps 1 to 3 in Changing system
settings.
5
• Depending on the channel currently being
received you may be able to select "service".
32
Watching TV (TV Guide On Screen)
Press b to select “General default options”,
and press ENTER.
4
5
Press MENU to display “General Defaults”.
6Press abcd/ / / to set the following items.
7
When you have finished, press toa b/
select “done”, and then press againENTER
to exit.
Record default options
Press b to select “Record defaults”, and
press ENTER.
3
Press ENTER to display “Record Defaults”.
4
Press abcd/ / / to set the following items.
6
When you have finished, press toa b/
select “done”, and then press againENTER
to exit.
Changing default options
This setting lets you change the default settings as
follows.
General default options
last used/no/small/
large
all/no only/small only/
large only/no & small/
no & large/small &
large
on/off
Setup
items
Info box size
box cycle
auto guide
DescriptionSelectable items
Set the initial info box
size when you enter
the TV Guide On
Screen
Set the info box
rotation when you
press INFO
When this is set to
“on”, automatic entry
into the TV Guide On
Screen when you turn
on the TV
on time/120 min early
... 120 min late
on time/120 min early
... 120 min late
VCR
Setup
items
start
end
recorder
DescriptionSelectable items
Set the start timing of
recording
Set the end timing of
recording
Set the external
recording device
Press TV GUIDE and then press MENU.
1
Press a b/ to select “go to Service Bar” in
“Episode Options”, and then press ENTER.
2
3
Press c d/ to select “SETUP” .
Press TV GUIDE and then press MENU.
1
Press a b/ to select “go to Service Bar” in
“Episode Options”, and then press ENTER.
2
5
34
Watching TV
Changing channels-Air/Cable
You can change channels in several ways by pressing
AIR CABLE or to select the antenna and then following
one of the methods below .
Method 1
Using CHr s/ on the remote control unit or on the TV.
Method 2
1. Press FLASHBACK to switch to the previously tuned
channel.
2. Press FLASHBACK again to switch back to the
currently tuned channel.
NOTE
•FLASHBACK will not work if no channel has been
changed after TV is turned on.
Method 3
Using remote control buttons (0–9,•(DOT) to select
channels for VHF/UHF/CATV/DIGITAL.
To select a 1 or 2-digit channel number
(e. g., Channel 5):
Press 5s ENT
NOTE
• When selecting a 1-digit channel number, it is not
necessary to press before the number.0
• When you enter only, channel selection will be made0–9
if there is no operation for a few seconds.
To select a 3-digit channel number
(e. g., Channel 115):
Press 1s s1 5
NOTE
• When you enter only, channel selection will be made0–9
if there is no operation for a few seconds.
• If you push “0” by itself, nothing will happen.
• Complete the above steps within a few seconds.
• When you enter and • (DOT), channel selection will0–9
be made if there is no operation for a few seconds.
To select a 4-digit channel number
(e. g., Channel 22.1):
Press 2 s s s s2• (DOT) 1 ENT
5
Air
5
Air ANALOG
11
Cable
1
Cable
115
Cable ANALOG
22.
Air Air DIGITAL
22.122.1
Air
22
Air
2
Air
Method 4
1. Press INPUT.
2. Press a b/ to select CableBox [TV], and then press
ENTER.
3. Press CHr s/ to change the channel of the cable
box.
INPUT SOURCE
TV
CableBox [TV]
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5INPUT5
i.LINK
35
Watching TV
Volume adjustment
Mute
■ Using VOL kkkkk/lllll
• To increase the volume, press VOL kkkkk.
• To decrease the volume, press VOL ll
lll.
Output device
Variable sound
Output Select
VariableFixed
Variable sound
Constant as
specified
Mute
NOTE
• / /VOL l kon the TV operates the same as VOL k l on
the remote control unit.
Audio status
Speaker
MONITOR OUT
Changing volume/sound
■ Changing the volume
You can change the volume on the TV or on the remote
control unit.
* When “Output Select” is set to “Variable”, the indicator on
the screen changes as shown below.
NOTE
• See page 71 for details on the output select function.
■ Using MUTE on the remote control unit
Mutes the current sound output.
Press MUTE.
• “M” will be displayed on the screen for 30
minutes, and the sound is silenced.
NOTE
• Within 30 minutes of pressing MUTE, mute can be
canceled by using one of the methods below.
• Mute will cancel if you press or VOL l k/MUTE.
• Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
20
20
20
1
■ Using Virtual on the remote control unit
Virtual produces Dolby Virtual effect from the
speakers. Each time you press Virtual, the mode
changes between On and Off.
Dolby Virtual sound options
• On: Makes it possible to enjoy natural, realistic
surround sound.
• Off: Outputs the normal sound.
NOTE
• You can have the same settings by choosing “Dolby
Virtual” on the menu items. (See page 48.)
Dolby Virtual : Off Dolby Virtual : On
36
Watching TV
NOTE
• MTS only operates while in TV mode.
You can change MTS as
shown below to match
the television broadcast
signal.
STEREOkSAP mode MONO mode
Examples: when receiving MTS and SAP
STEREO mode MAINkSAP mode
Setting MTS/SAP stereo mode
The TV has a feature that allows reception of sound
other than the main audio for the program. This feature
is called Multi-channel Television Sound (MTS). The
TV with MTS can receive mono sound, stereo sound
and Secondary Audio Programs (SAP). The SAP
feature allows a TV station to broadcast other
information, which could be audio in another language
or something completely different like weather
information.
You can enjoy Hi-Fi stereo sound or SAP
broadcasts where available.
•Stereo broadcasts
View programs like live sporting events, shows and
concerts in dynamic stereo sound.
•SAP broadcasts
Receive TV broadcasts in either MAIN or SAP sound.
MAIN sound: The normal program soundtrack (either in
mono or stereo).
SAP sound: Listen to second language, supplementary
commentary and other information. (SAP is mono sound.)
If stereo sound is difficult to hear.
• Obtain a clearer sound by manually switching to fixed
mono-sound mode.
2
Air ANALOG
Audio : MONO
2
Air ANALOG
Audio : ST(SAP)
2
Air ANALOG
Audio : SAP(ST)
2
Air ANALOG
Audio : MONO
2
Air ANALOG
Audio : MONO
2
Air ANALOG
Audio : STEREO
2
Air ANALOG
Audio : MAIN
2
Air ANALOG
Audio : SAP
Setting Digital broadcasting audio
mode
The types of audio transmitted in a digital broadcast
include SURROUND as well as MONO and STEREO.
In addition, it is possible for multiple audio tracks to
accompany a single video track.
Press AUDIO to toggle
between audio modes.
Examples: when receiving Digital broadcasting
2.2
Air DIGITAL
Audio3 :
SURROUND
2.2
Air DIGITAL
Audio1 : STEREO
2.2
Air DIGITAL
Audio2 : STEREO
37
Connecting Digital Cable Module
Digital Cable Module is called CableCARD™. By attaching the CableCARD, you can receive various digital
services provided by your Cable Company. To obtain and use a CableCARD you need to first submit an
application.
Please contact your cable company to discuss receiving an application.
Watching TV
Connect the antenna cable to DIGITAL
CABLE IN.
2
Insert the CableCARD (upper side facing
right) into the CableCARD slot.
• A message will appear on the screen. (It might
take a couple of minutes before the message
appears.) Call the number on the screen and
tell the operator the CableCARD ID and Host
ID numbers displayed on the screen.
2
Press c d a b/ to select “Digital Setup”, / to
select “CableCARD Menu”, to selecta b/
“Pairing Information”, and then press
ENTER.
3
Press MENU and the MENU screen displays.
1
A message will appear on the screen. Call
the number on the screen and tell the
operator the CableCARD ID and Host ID
numbers displayed on the screen.
Pairing Information
Diagnostic Screen
ECM
Conditional Access
CableCARD Dialog
CableCARD(tm) Pairing Status
In order to start cable service
for this device, please contact
your cable provider
1-888-555-2222
CableCARD(tm) ID:
7-561-034-449-009
Host ID:
0-100-331-784-018
• If there is a white triangle at the right side of
the screen, the screen is not showing the entire
message. Press on your remote controla b/
to display the rest of the message.
• When there is a “LINK” button on the screen,
there is a link to the next page. Press ENTER
to go to the next page.
NOTE
• Do not insert any PCMCIA card other than CableCARD
into the CableCARD slot.
• Please do not pull the AC cord out while the CableCARD
is inserted.
• After inserting the CableCARD, it may take several minutes
before video output from the selected channel appears
on screen.
■If the above procedure does not work,
please follow the following steps instead.
CableCARD(tm) Pairing Status
In order to start cable service
for this device, please contact
your cable provider
1-888-555-2222
CableCARD™ ID:
7-561-034-449-009
Host ID:
0-100-331-784-018
• The words “Pairing Information” may be
replaced by a different expression depending
on the manufacturer of the CableCARD.
CableCARD(tm)
Diagnostic Information
Power: ON
In band: O.K.
Out of band: O.K.
Video: O.K.
Audio: O.K.
LINK
Turn on the power of the TV.
1
3
1Turn on the power of the TV.
2Check that the CableCARD upgrade screen is not
displayed. If it is displayed, wait until it disappears.
3Remove the CableCARD.
■ When you change your address (See page 89.)
■ About EAS (Emergency Alert System) (See page
89.)
Removing CableCARD
Disconnecting the cable antenna
1Turn on the power of the TV.
2Check that the CableCARD upgrade screen is not
displayed. If it is displayed, wait until it disappears.
3Disconnect the cable antenna.
NOTE
• If your cable company does not have CableCARD available, you must connect to the cable-TV set-top box via component
video or DVI in order to receive HDTV programs. (See page 55.)
38
Basic adjustment settings
AV input mode menu items
List of AV menu items to help you with operations
OPC ................................................ Page 45
Backlight ........................................ Page 44
Contrast ......................................... Page 44
Brightness ..................................... Page 44
Color ............................................... Page 44
Tint ................................................. Page 44
Sharpness ...................................... Page 44
Advanced
C.M.S. ................................... Page 45
Color Temp. ......................... Page 46
Black .................................... Page 46
3D-Y/C .................................. Page 46
Monochrome ....................... Page 47
Film Mode ............................ Page 47
I/P Setting ............................ Page 47
Picture
No Signal Off ................................. Page 49
No Operation Off ........................... Page 49
EZ Setup ................................ Pages 39, 40
CH Setup ................................ Pages 40, 41
Antenna Setup-DIGITAL ............... Page 42
Input Label ..................................... Page 67
Parental CTRL ........................ Pages 79-83
Position .......................................... Page 64
Picture Flip .................................... Page 67
Standby Mode ............................... Page 42
Language ....................................... Page 43
Treble .............................................. Page 48
Bass ............................................... Page 48
Balance .......................................... Page 48
Dolby Virtual .................................. Page 48
Audio Only ..................................... Page 70
Digital Noise Reduction ............... Page 70
HDMI Setup .................................... Page 56
Input Select.................................... Page 66
Output Select................................. Page 71
Quick Shoot ................................... Page 71
Caption Setup......................... Pages 73-76
Program Title Display ................... Page 72
Audio
Power Control
Setup
Option
CableCARD Menu ......................... Page 37
Video Setup ................................... Page 50
Audio Setup ................................... Page 51
i.LINK Setup............................ Pages 58-63
Digital Setup
39
Basic adjustment settings
Power Management ...................... Page 49
Input Signal ................................... Page 70
Auto Sync. ..................................... Page 65
Input Label ..................................... Page 67
Fine Sync. ...................................... Page 65
Picture Flip .................................... Page 67
Standby Mode ............................... Page 42
Language ....................................... Page 43
Power Control
Setup
Option
Audio Only ..................................... Page 70
Input Select .................................... Page 66
Output Select ................................. Page 71
Quick Shoot ................................... Page 71
EZ Setup
You can run EZ Setup again, even after setting up the
preset channels.
Language setting
Select from among 3 languages: English, French and
Spanish.
Press MENU and the MENU screen displays.
Press c d/ to select “Setup”.
1
2
Press a b/ to select “EZ Setup”, and then
press ENTER.
• If you already set the Secret No., go to step 4. If
not, skip to step 5.
Input the 4-digit secret number by using – 0 9.
3
MENU
[Setup ... EZ Setup]
Setup Option
Secret No. ––––
4
5
Press a b/ to select the desired language
listed on the screen, and then press ENTER.
Language
Air/Cable
CH Search English
Español
Français
i.LINK Setup............................ Pages 58-63
Digital Setup
*PC input mode menu items
List of PC menu items to help you with
operations
*When INPUT5 is set to PC.
OPC ................................................ Page 45
Backlight ........................................ Page 44
Contrast ......................................... Page 44
Brightness ..................................... Page 44
Red ................................................. Page 44
Green .............................................. Page 44
Blue ................................................ Page 44
Advanced
C.M.S. ................................... Page 45
Picture
Audio
Treble .............................................. Page 48
Bass ............................................... Page 48
Balance .......................................... Page 48
Dolby Virtual .................................. Page 48
41
Basic adjustment settings
Channel search
Channel auto search makes the TV look for all channels
viewable in the set area.
Press MENU and the MENU screen displays.
Press c d/ to select “Setup”.
1
2
3
Press a b/ to select “CH Search”, and then
press ENTER.
Air/Cable
CH Search
ANALOG Yes
DIGITAL (Air)
No
Yes No
DIGITAL (Cable) Yes No
CH Memory
Search Start
Press c d/ to select “Yes” for ANALOG, then
press b to move down.
Press c d/ to select “Yes” for DIGITAL (Air),
then press to move down.b
Press c d/ to select “Yes” for DIGITAL
(Cable), and press to move down.b
Select “Search Start”, and then press
ENTER.
4
5
NOTE
• Make sure what kind of connection is made with your TV.
Press a b/ to select “CH Setup”, and then
press ENTER.
• If you already set the Secret No., input the 4-
digit secret number here. See page 77 for
setting a secret number.
Example: CH Search
MENU [Setup ... CH Setup ... CH Search]
ANALOG [ ]25 [ ]20FoundAir
MENU [Setup ... CH Setup ... CH Search]
DIGITAL [ ]25 [ ]20FoundAir
MENU [Setup ... CH Setup ... CH Search]
DIGITAL [ ]25 [ ]25FoundCable
Channel memory setting
Press MENU and the MENU screen displays.
Press c d/ to select “Setup”.
1
2
3
4
Press a b/ to select “CH Setup”, and then
press ENTER.
• If you already set the Secret No., input the 4-
digit secret number here. See page 77 for
setting a secret number.
Press a b/ to select ANALOG, DIGITAL (Air),
DIGITAL (Cable) and CableCARD, and then
press ENTER.
5
6
Press a b/ to select “CH Memory”, and then
press ENTER.
Perform the following steps after confirming
the type of antenna connection made with
your TV, and the channel type selected in
Step 5.
When viewing ANALOG broadcasts:
1 a b c dPress / , and then press / to select
the channel to skip or not.
2 a bPress / to select “Skip”, and then press
c d/ to select “On” or “Off”.
When viewing DIGITAL broadcasts:
1 a bPress / to select the channel to skip or
not, and then press to select “On” orc d/
“Off”.
• On: Skips channels. (Channel selection disabled using
CHrrrrr/sssss.)
• Off: Does not skip channels. (Channel selection enabled
using CHrr
rr
r/ss
ss
s.)
NOTE
• Make sure what kind of connection is made with your TV.
42
Basic adjustment settings
Antenna Setup – DIGITAL – Air
In order to receive digital air broadcasts, you need a
digital broadcast antenna. You can confirm the antenna
configuration through the “Antenna Setup - DIGITAL”
screen.
If necessary, adjust the direction of the antenna to
obtain the maximum signal strength.
1
2
Press MENU and the MENU screen displays.
Press c d/ to select “Setup”.
Press a b/ to select “Antenna Setup -
DIGITAL”, and then press ENTER.
• If you already set the Secret No., input the 4-
digit secret number here. See page 77 for
setting a secret number.
4
3
Press a b/ to select “Signal Strength”.
• The signal strength of the DIGITAL (Air) antenna
is displayed. The signal information is based
on the current channel.
Signal Strength
Channel Strength
Signal Strength
Current Max0 0
Signal Strength
Standby Mode
Standby Mode may be set to either start the TV quickly
from standby or conserve energy while on standby.
1
2
3
Press MENU and the MENU screen displays.
Press c d/ to select “Setup”.
Press a b/ to select “Standby Mode”, and
then press ENTER.
4
Press a b/ to select “Mode1” or “Mode2”,
and then press ENTER.
Selected item Description
Mode1
Mode2
Starting TV is quick from standby.
Power consumption is small at the
standby.
Press a b/ to select “Channel Strength”, and
then press ENTER.
Input the 2-digit channel number to check
the signal strength of the selected channel.
• Make sure the appropriate signal strength of
each channel received is obtained.
Signal Strength
Current
CH
Max0
1 2
0
Signal Strength
Channel Strength
Channel Strength
• The channel signal strength can also be checked
separately.
2
3
1
Repeat steps 1 to 3 in Signal Strength in
Antenna Setup - DIGITAL - Air.
NOTE
• This function is available for DIGITAL (Air) only.
43
Basic adjustment settings
Favorite channel setting
This function allows you to program 4 favorite channels,
in 4 different categories. By setting the favorite
channels in advance, you can select your favorite
channels easily.
Press EDIT.
Press a b/ to select “Register”, and then
press ENTER.
2
3
Press EDIT and the favorite channel screen
displays.
Press a b/ to select “1 Data Clear”, and then
press ENTER.
Press a b c d/ / / to select the position in the
area, and then press to register.ENTER
Press a b c d/ / / to select the channel you
want to delete, and then press ENTER.
1
2
3
ANALOG
3
ABCD
ANALOG
3
ANALOG
18
ANALOG
125
D-Air
10.1
ANALOG
33
ANALOG
51
ABCD
Register
All Data Clear
1 Data Clear
Deleting favorite channel
ANALOG
3
ANALOG
125
ANALOG
33
ANALOG
51
ABCD
D-Air
10.1
Yes No
NOTE
• You can delete all the favorite channels by selecting “All
Data Clear” in step 2 in Deleting favorite channel.
Select the channel you want to register as a
favorite channel.
1
4
4
Press c d/ to select “Yes”, and then press
ENTER.
Language setting
You can also select a language from the Setup menu.
Select from among 3 languages: English, French and
Spanish.
3
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Setup”.
Press a b/ to select “Language”, and then
press ENTER.
4
English
Español
Français
Press a b/ to select the desired language
listed on the screen, and then press ENTER.
44
Adjustments for PC source
Basic adjustment settings
cbutton
The screen dims
For less contrast
For less brightness
For less color
intensity
Skin tones become
purplish
For less sharpness
Selected item
Backlight
Contrast
Brightness
Color
Tint
Sharpness
Adjustments for AV source
MENU [Picture]
Picture Audio
Contrast
OPC
Brightness
Reset
[+30]
[ 0]
0
–30
+40
+30
Backlight [ +8] –8 +8
Off On
Red
Green
Blue
Advanced
[ 0]
[ 0]
[ 0]
–30
–30
–30
+30
+30
+30
On : Display
MENU [Picture]
Picture Audio
Contrast
OPC
Brightness
Color
Tint
Sharpness
Advanced
Reset
[+30]
[ 0]
[ 0]
[ 0]
[ 0]
0
–30
–30
–30
–10
+40
+30
+30
+30
+10
Backlight [ +8] –8 +8
Off On On : Display
NOTE
• Select “Advanced” and then press ENTER to set “C.M.S-
Hue”, “C.M.S-Saturation”, “C.M.S-Value”, “Color Temp.”,
“Black”, “3D-Y/C”, “Monochrome”, “Film Mode” or “I/P
Setting”. See pages 45 to 47.
dbutton
The screen brightens
For more contrast
For more brightness
For more color
intensity
Skin tones become
greenish
For more sharpness
cbutton
The screen dims
For less contrast
For less brightness
For weaker red
For weaker green
For weaker blue
Selected item
Backlight
Contrast
Brightness
Red
Green
Blue
dbutton
The screen brightens
For more contrast
For more brightness
For stronger red
For stronger green
For stronger blue
Picture adjustments
Adjusts the picture to your preference with the following
picture settings.
Press MENU and the MENU screen displays.
1
2
3
4
Press a b/ to select a specific adjustment
item.
Press c d/ to adjust the item to your desired
position.
Press c d/ to select “Picture”.
NOTE
• For resetting all adjustment items to factory preset values,
press a b/ to select “Reset”, press ENTER, press c d/
to select “Yes”, and then press ENTER.
NOTE
• Select “Advanced” and then press ENTER to set “C.M.S-
Hue”, “C.M.S-Saturation” and “C.M.S-Value”.
45
OPC setting
Automatically adjusts the brightness of the screen.
Press c d/ to select “Picture”.
2
Press MENU and the MENU screen displays.
1
Press a b/ to select “OPC”.
Press c d/ to select “On” or “On: Display”.
3
4
Basic adjustment settings
Description
The brightness is fixed at the value set in
“Backlight” (see page 44).
Automatically adjusts
Displays the OPC effect on the screen while
adjusting the brightness of the screen.
Selected item
Off
On
On: Display
NOTE
• When set to “On”, the OPC senses the surrounding light
and automatically adjusts the backlight brightness. Make
sure no object obstructs the OPC sensor, which could
affect its ability to sense surrounding light.
• When set to “On: Display”, OPC effect displays on the
screen while OPC is adjusting the screen brightness.
Contrast
OPC
Brightness
Color
Tint
Sharpness
Advanced
Reset
[+30]
[ 0]
[ 0]
[ 0]
[ 0]
0
–30
–30
–30
–10
+40
+30
+30
+30
+10
Backlight [ +8] –8 +8
Off On On : Display
C.M.S. (Color Management System)
Color tone is managed using the six-color adjustment
setting.
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Picture”.
3
Press a b/ to select “Advanced”, and then
press ENTER.
4
Press a b/ to select “C.M.S-Hue”, and then
press ENTER.
5
Press a b/ to select a specific adjustment
item. Press to adjust the item to yourc d/
desired position.
C. M. S.-Hue
R
Y
G
C
B
M
Reset
[ 0]
[ 0]
[ 0]
[ 0]
–30
–30
–30
+30
–30 +30
+30
+30
[ 0] –30 +30
[ 0] –30 +30
Changing reds
closer to
magenta or yellow.
C. M. S.-Saturation
C. M. S.-Value
NOTE
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
• You can select “C.M.S-Saturation” or “C.M.S-
Value” here instead of selecting “C.M.S-Hue”.
Description
This is a standard to adjust the color either
more reddish or more bluish in tone.
Increases or decreases the saturation of a
selected color.
A higher value makes the image brighter.
A lower value makes the image darker.
Selected item
C.M.S-Hue
C.M.S-
Saturation
C.M.S-
Value
46
Basic adjustment settings
Color temperature
For a better white balance, use color temperature
correction.
4
5
Press a b/ to select “Color Temp.”, and then
press ENTER.
Description
White with Bluish tone
White with Reddish tone
Selected item
High
Mid-High
Middle
Mid-Low
Low
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Picture”.
3
Press a b/ to select “Advanced”, and then
press ENTER.
C. M. S-Hue
C. M. S-Saturation
C. M. S-Value
Color Temp.
Black
3D-Y/C
Monochrome
Film Mode
I/P Setting
High
Mid-High
Middle
Mid-Low
Low
Black
For easier viewing, change the viewing depth by
selecting a level for automatically adjusting the dark
portion of an image.
Press a b/ to select the desired level, and
then press ENTER.
Press a b/ to select “Black”, and then press
ENTER.
Press c d/ to select “On”, and then press
ENTER.
Repeat steps 1 to 3 in Color temperature.
1
2
3
Description
No adjustment
For high detail in black portions
Selected item
Off
On
3D-Y/C
Provides high quality images with minimal dot crawl
and cross color noise.
Description
Normal adjustment
For movie image
For still image
Selected item
Standard
Fast
Slow
Press a b/ to select “3D-Y/C”, and then
press ENTER.
Repeat steps 1 to 3 in Color temperature.
1
2
3
Press a b/ to select the desired level, and
then press ENTER.
NOTE
• 3D-Y/C is available for input signal from Composite Video
and ANALOG IN.
47
Basic adjustment settings
Monochrome
For viewing a video in monochrome.
Description
Normal color
For viewing in monochrome
Selected item
Off
On
Press a b/ to select “Monochrome”, and
then press ENTER.
4
Press c d/ to select “On”, and then press
ENTER.
5
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Picture”.
3
Press a b/ to select “Advanced”, and then
press ENTER.
C. M. S-Hue
C. M. S-Saturation
C. M. S-Value
Color Temp.
Black
3D-Y/C
Monochrome
Film Mode
I/P Setting
On Off
Film Mode (3:2 pull-down)
Automatically detects a film-based source (originally
encoded at 24 frames/second), analyzes it then
recreates each still film frame for high-definition picture
quality.
Description
Normal viewing mode
Detects, analyzes, converts film source
Selected item
Off
On
Press a b/ to select “Film Mode”, and then
press ENTER.
Repeat steps 1 to 3 in Monochrome.
1
2
3
Press c d/ to select “On”, and then press
ENTER.
I/P Setting
Converts input signals from interlace to progressive.
Press a b/ to select “I/P Setting”, and then
press ENTER.
Press c d/ to select “Fast” or “Slow”, and
then press ENTER.
Repeat steps 1 to 3 in Monochrome.
1
2
3
NOTE
• I/P Setting is set to Slow when Film Mode is “On”.
• “I/P Setting” is not selectable when channel display shows
an input resolution of 480P or 720P.
48
Basic adjustment settings
Sound adjustment
You can adjust the sound quality to your preference
with the following settings.
Press c d/ to select “Audio”.
Press a b/ to select a specific adjustment
item.
Press c d/ to adjust the item to your desired
position.
2
3
4
cbutton
For weaker treble
For weaker bass
Decrease audio from
the right speaker
Selected item
Treble
Bass
Balance
dbutton
For stronger treble
For stronger bass
Decrease audio from
the left speaker
Press MENU and the MENU screen displays.
1
MENU
[Audio]
Audio Power Control
Treble
Bass
Balance
Dolby Virtual
Reset
[Off]
–15
L
+15
[ 0]
[ 0]
[ 0]
–15 +15
R
NOTE
• Audio menu is grayed out when Output Select is set to
“Variable”.
• “Balance”, “Treble” and “Bass” are grayed out when Dolby
Virtual is set to “On”.
• For resetting all adjustment items to factory preset values,
press a b/ to select “Reset”, press ENTER, press c d/
to select “Yes”, and then press ENTER.
Press c d/ to select “Audio”.
Press a b/ to select “Dolby Virtual”, and
then press ENTER.
Press c d/ to select “On”, and then press
ENTER.
2
3
4
Press MENU and the MENU screen displays.
1
Dolby Virtual
You can enjoy the SURROUND 2ch stereo with Dolby
Pro Logic II technology.
VIRTUAL DOLBY DIGITAL is a technology certified by
Dolby Laboratories that creates a virtualized surround
sound experience from two speakers using Dolby Pro
Logic or Dolby Pro Logic II.
VIRTUAL DOLBY DIGITAL retains all the original
multichannel audio information and provides the
listener with the sensation of being surrounded by
additional speakers.
MENU [Audio ... Dolby Virtual]
Audio Power Control
Treble
Bass
Balance
Dolby Virtual
Reset
[Off]
–15
L
+15
–15 +15
R
[ 0]
[ 0]
[ 0]
NOTE
• You can choose Dolby Virtual by pressing Virtual on
the remote control unit.
• Audio menu is grayed out when Output Select is set to
“Variable”.
• “Balance”, “Treble” and “Bass” are grayed out when Dolby
Virtual is set to “On”.
• For some discs, setup may be required on your DVD. In
this case, please refer to the operation manual of your
DVD player.
49
Basic adjustment settings
No signal off
When set to “Enable”, the power will automatically shut
down if no signal inputs for 15 minutes.
Press a b/ to select “No Signal Off”, and
then press ENTER.
Press c d/ to select “Enable”, and then
press ENTER.
3
4
• Five minutes before the power shuts down,
remaining time displays every minute.
NOTE
• “Disable” is factory preset value.
• When a TV program finishes, this function may not operate.
Press c d/ to select “Power Control”.
Press MENU and the MENU screen displays.
No operation off
When set to “Enable”, the power will automatically shut
down if there is no operation for 3 hours.
Press a b/ to select “No Operation Off”, and
then press ENTER.
Press c d/ to select “Enable”, and then
press ENTER.
• Five minutes before the power shuts down,
remaining time displays every minute.
NOTE
• “Disable” is factory preset value.
Repeat steps 1 and 2 in No signal off.
2
1
DisableEnable
3
2
1
Power Control
Power control setting allows you to save energy.
Power control for AV source
Power control for PC source
Power control setting allows you to save energy.
Power management
When set, the power will automatically shut down.
Press a b/ to select “Power Management”,
and then press ENTER.
Press a b/ to select “Mode1” or “Mode2”,
and then press ENTER.
Description
• No power management
• Factory preset value.
• If no signal inputs for 8 minutes, the power
shuts down.
• Even if you start using the PC and the signal
inputs again, the TV stays off.
• The TV turns on again by pressing TV
POWER on the remote control unit. (See
page 17).
• Pressing POWER on the TV will have the
same result.
• If no signal inputs for 8 seconds, the TV
enters standby mode.
• When you start using the PC and the signal
inputs again, the TV turns on.
Selected item
Off
Mode1
Mode2
Repeat steps 1 and 2 in No signal off.
3
2
1
Off
Mode1
Mode2
NOTE
• When using a digital PC and setting “Mode2” in Power
management, the power may not turn back on
automatically even if the signal inputs again.
• If you turn off the power by disconnecting AC cord when
setting “Mode2” in power management, the TV may not
function properly after turning the power on again. In such
case, press TV POWER on the remote control unit.
• Pressing POWER on the TV will have the same result.
50
Basic adjustment settings (DIGITAL)
Digital Setup
This setting allows you to set the image of Digital
broadcasting.
Video Setup
You can adjust the settings for Digital image.
1
2
3
Press MENU and the MENU screen displays.
Press c d/ to select “Digital Setup”.
Screen Size
Set the format of image of Digital broadcasting.
Press a b/ to select “Video Setup”, and then
press ENTER.
4
Press a b/ to select “Screen Size”, and then
press ENTER.
NOTE
• “Manual” is factory preset value.
REC Picture Size
Select the screen size to record on 16:9 video.
Press MENU and the MENU screen displays.
Press c d/ to select “Digital Setup”.
Press a b/ to select “Video Setup”, and then
press ENTER.
Press a b/ to select “REC Picture Size”, and
then press ENTER.
Press c d/ to select the desired picture size,
and then press ENTER.
Selected item Description
4:3 TV
16:9 TV
Bars may appear on the top and
bottom with some programs
Displays in full screen
1
2
3
4
5
Screen Size
REC Picture Size
4 : 3 TV 16 : 9 TV
Screen Size
REC Picture Size
Manual Auto
Selected item Description
Manual
Auto
With 480i/480p/720p broadcasts
you can change the screen size
to the size of your choice.
All broadcasts will be converted
and displayed in the 1080i
format.
Press to select “Manual” or “Auto”.c d/
5
51
Basic adjustment settings (DIGITAL)
Audio Setup
You can output digital audio to an AV amplifier or similar
device whose DIGITAL AUDIO INPUT terminal is
connected to the DIGITAL AUDIO OUTPUT terminal
on the TV. Please select an audio output format
compatible with the audio format of the program you
are watching and the equipment connected.
1
2
3
Press MENU and the MENU screen displays.
Press c d/ to select “Digital Setup”.
Press a b/ to select “Audio Setup”, and then
press ENTER.
4
Press a b/ to select “PCM” or “Dolby
Digital”, and then press ENTER.
Selected item Description
PCM
Dolby Digital
The optical output terminal outputs
audio signal by PCM form. If your
digital audio system does not
support Dolby Digital, select “PCM”.
The optical output terminal outputs
audio signal by Dolby Digital form.
It reproduces sound from surround
program of digital.
PCM
Dolby Digital
52
Using external equipment
You can connect many types of external equipment to your TV, like a DVD player, VCR, Digital TV tuner, PC,
HDMI equipment, game console and camcorder. To view external source images, select the input source from
INPUT on the remote control unit or on the TV.
CAUTION
• To protect all equipment, always turn off the TV before
connecting to a DVD player, VCR, Digital TV tuner, PC,
HDMI equipment, game console, camcorder or other
external equipment.
NOTE
• See pages 53 to 58 for external equipment connection.
• Please refer to the relevant operation manual (DVD player,
PC, etc.) carefully before making connections.
• Each time is pressed, the input source toggles.INPUT
• Refer to your external equipment operation manual for
the signal type.
Displaying an external equipment image
Explanation here is for the setting when connecting
DVD to INPUT1 terminal.
To watch a DVD image, select “INPUT1” from “INPUT
SOURCE” menu using on the remote controlINPUT
unit or on the TV. (See page 66.)
INPUT SOURCE
TV
CableBox [TV]
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5INPUT5
i.LINK
1
MENU [Option ... Input Select]
Auto
COMPONENT
VIDEO
For INPUT1 signal
Select the desired signal type.
The setting is stored and can be selected on the
“INPUT SOURCE” menu.
Press MENU and the MENU screen displays.
2
3
Press a b/ to select “Input Select”, and then
press ENTER.
4
Press c d/ to select “Option”.
MENU [Option ... Input Select]
Option
Input Select
Digital Noise Reduction
Output Select
Audio Only
Quick Shoot
[Fixed]
[Auto]
[Low]
[Off]
Caption Setup
Program Title Display [No]
NOTE
• If the image does not come in clearly, you may need to
change the input signal type setting on the “Input Select”
menu.
Selecting the INPUT signal
53
Using external equipment
Connecting a DVD player
You can use the INPUT 1, INPUT 2, INPUT 4 or INPUT 5 terminals when connecting to a DVD player and other
audiovisual equipment.
NOTE
• See page 56 for connecting a DVD player with HDMI terminal.
DVD player
Component
video cable
(commercially
available) Audio cable
(commercially available)
AV cable (commercially
available)
DVD player
ø 3.5 mm stereo minijack cable
(commercially available) DVI cable (Commercially available)
When using component cable.
When using composite cable.
When using DVI cable. (INPUT 5)
DVD player
54
Using external equipment
VCR
AV cable
(commercially
available)
Connecting a VCR
You can use the INPUT 3 terminal when connecting a VCR and other audiovisual equipment.
Game console/Camcorder
S-video cable
(commercially
available)
Connecting a game console or camcorder
A game console, camcorder and some other audiovisual equipment are conveniently connected using the
INPUT 3 terminals.
NOTE
• The S-video terminal has priority over the video terminals.
• The G-LINK cable connection is necessary if you want to use the recording features of the TV Guide On Screen system
with your VCR.
AV cable
(commercially available)
S-video cable
(commercially
available)
NOTE
• The S-video terminal has priority over the video terminals.
This connection is necessary
when using TV Guide On
Screen’s recording function.
(commercially available)
(INPUT)(OUTPUT)
G-LINK cable
G-LINK
cable
This end is connected
to the TV.
1 inch
VCR
G-LINK wand
55
Using external equipment
Connecting a Digital TV STB (Air or Cable)
You can use the INPUT 1, INPUT 2, INPUT 4 or INPUT 5 terminals when connecting a Digital TV STB (Air or
Cable) and other audiovisual equipment.
Digital TV STB
Component video
cable
(commercially
available) Audio cable
(commercially available)
NOTE
• See page 56 for connecting a Digital TV STB to HDMI terminal.
AV cable
(commercially available)
Digital TV STB
Digital TV STB
ø 3.5 mm stereo
minijack cable
(commercially
available)
DVI cable
(commercially available)
When using component cable.
When using composite cable.
When using DVI cable. (INPUT 5)
NOTE
• If your cable-TV company has CableCARD available, you can also use the CableCARD to receive
HDTV programs. (See page 37.)
G-LINK cable
G-LINK
cable
This end is connected
to the TV.
1 inch
Cable Box
G-LINK wand
Cable box connection
(for TV Guide On Screen)
NOTE
• To receive TV program listings in the TV Guide On Screen system, please connect your cable box
using this input, marked “VIDEO”. Do not connect the cable box to the “COMPONENT” video as you
will not receive any TV program listings.
56
Using external equipment
Connecting HDMI equipment
Please use the INPUT 4 terminal when connecting HDMI equipment.
HDMI equipment
HDMI cable
(Commercially available)
Displaying an image from HDMI equipment
To watch an HDMI equipment image, select
“INPUT4” from “INPUT SOURCE” menu
using INPUT on the remote control unit or
on the TV. (See page 66.)
INPUT SOURCE
TV
CableBox [TV]
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5INPUT5
i.LINK
1
Press MENU and the MENU screen displays.
2
3
Press a b/ to select “HDMI Setup”, and then
press ENTER.
4
Press c d/ to select “Option”.
MENU [Option ... HDMI Setup]
Option
Digital Noise Reduction
Audio Only
HDMI Setup
[Low]
5
Press a b/ to select the desired item and
press ENTER.
Press abcd/ / / to select the desired setting
and press ENTER.
6
NOTE
• Refer to your external equipment operation manual for
the signal type.
Selectable items
Auto/RGB/YCbCr
4:4:4/YCbCr 4:2:2
Auto/ITU601/
ITU709
Standard/
Out of Standard
Enable/Disable
HDMI Setup
items
Signal
Type
Color
Matrix
Dynamic
Range
Auto View
Description
Select the signal type from
an HDMI terminal. Unless
the image quality looks
obviously poor, select Auto.
Select the internal color
space conversion method
when an RGB signal is
input. Normally, select
Auto.
Select the signal amplitude
range. Normally, select
Standard.
Set whether or not to use
VIEW MODE based on
signal recognition,
including an HDMI signal.
57
Using external equipment
Connecting a PC
Use the INPUT 5 terminal to connect a PC.
NOTE
• Refer to page 93 for a list of PC signals compatible with the TV.
PC with DVI terminal
ø 3.5 mm stereo minijack cable
(commercially available)
DVI cable (Commercially available)
ø 3.5 mm stereo minijack cable
(commercially available)
PC with analog RGB terminal
RGB/DVI conversion cable
(Commercially available)
58
Connecting D-VHS decks/AV-HDD
recorder/Blu-ray Disc recorder (i.LINK
connection)
Using external equipment
About i.LINK
i.LINK is an interface connection using a serial
transfer system and is able to transfer multimedia
data, such as digital images and digital sound,
between devices that have i.LINK terminals.
i.LINK is a term defined in the IEEE1394 (Institute of
Electrical and Electronics Engineers) standard.
Currently, the transfer speeds are at 100 Mbps, 200
Mbps and 400 Mbps, each of them expressed as
S100, S200 and S400 respectively. On this TV, the
maximum speed is 400 Mbps.
i. LINK devices that can be connected to this
TV.
Only D-VHS decks, AV-HDD recorders and Blu-ray
Disc recorders can be connected to this TV via
i.LINK. Other devices such as DVD recorders, digital
video cameras, computers or computer peripheral
devices do not meet the specifications for this TV
and therefore cannot be connected via i.LINK.
Even for the types of i.LINK device mentioned above,
device recognition, control, recording and playback
operations may not be possible on some devices.
Materials that can be recorded with the i.LINK
Only digital programs can be recorded by i.LINK
devices connected to this TV using the i.LINK. i.LINK
recording is not compatible with analog broadcasts
or external input signals (INPUT terminals 1 through
5).
i.LINK connection
Only an i.LINK cable is
needed to connect the TV
to i.LINK devices.
(VIDEO, S-VIDEO, and
AUDIO terminals need not
be connected.)
i.LINK device
Connecting two or more i.LINK devices
Up to 16 i.LINK devices can be connected using a
daisy-chain connection with i.LINK cables.
When 3 or more i.LINK devices are connected,
branch connection can be used. With branch
connections, up to 62 i.LINK devices can be
connected.
Cautions regarding i.LINK connection
• Please use S400 type i.LINK cables.
• Some i.LINK devices may not relay data if their power
is off. In this case the device should be connected
at the end of any series of connections.
• This TV can relay data during power off, by selecting
“Active” in the “Standby Mode” option in “i.LINK
Setup”. (See Page 59.)
• Please do NOT use a loop connection as shown in
the diagram.
• When using the i.LINK, do not turn off the power of,
or pull the cable from i.LINK devices, even if that
i.LINK devices is not in use. This may affect the
picture and the sound from an i.LINK device in use.
• If devices such as a DVD recorders, digital video
cameras, computers and computer peripheral
devices which are not compatible with this TV, are
connected to the TV using i.LINK, other i.LINK
connections may be disrupted.
• When device recognition, control, recording or play
back, on an i.LINK connected device does not
function correctly, correct operation may be restored
by disconnecting and reconnecting the i.LINK cable.
• When connecting multiple i.LINK devices, depending
on the specifications and the interoperability of the
connected devices, their operation may not be stable.
In that case, disconnecting all devices not in use
and changing the method of connection may result
in stable operation.
NOTE
• Please make sure the
shapes of the terminal
and the plug match,
and insert the plug into
the terminal straight,
not on an angle.
• Use either one of the
terminals. These two
terminals do not differ
in quality or function.
59
Using external equipment
Setting the Recording Mode (i.LINK)
• The function for automatically adjusting the recording
mode of connected i.LINK devices can be turned
on or off.
• Since most of the currently available i.LINK devices
automatically recognize the transfer rates of the
pictures and sound being recorded and control the
recording mode accordingly, you should always
set this Mode to “Pass through” in normal
circumstances.
• Depending on the i.LINK devices used and the type
of broadcast being recorded, this TV may not adjust
the recording mode properly. In this case, please
set the “Recording Mode” to “Pass through”.
Press MENU and the MENU screen displays.
Press c d/ to select “Digital Setup”.
Press a b/ to select “i.LINK Setup”, and then
press ENTER.
1
2
3
Press a b/ to select “Recording Mode”, and
then press ENTER.
4
Press c d/ to select “Auto” or “Pass
through”, and then press ENTER.
• Normally, this should be set to “Pass through”.
5
Setting the Standby Mode (i.LINK)
• Power consumption during standby mode can be
minimized by changing the setting of the “Standby
Mode” in “i.LINK Setup”.
• When i.LINK is not in use, select “Inactive” in
“Standby Mode”.
Press MENU and the MENU screen displays.
Press c d/ to select “Digital Setup”.
Press a b/ to select “i.LINK Setup”, and then
press ENTER.
1
2
3
Press a b/ to select “Standby Mode”, and
then press ENTER.
4
Press c d/ to select “Active” or “Inactive”,
and then press ENTER.
5
“Active”: Power continues to pass through the i.LINK
circuit so data can be relayed.
“Inactive”: Power consumption is minimized during
stand-by mode. Data cannot be relayed at this
setting.
NOTE
• When the main power of the TV is in standby mode
(POWER indicator lights off), i.LINK control commands
cannot be received from an i.LINK device. This does not
change even if the “Standby Mode” is set to “Active”. To
control the TV from an i.LINK device, turn the TV power
on (POWER indicator lights up in blue).
• Data cannot be relayed between i.LINK devices when all
the following conditions are met: 1) More than one i.LINK
device is connected to the TV with i.LINK cables, 2)
“Standby Mode” is set to “Inactive”, and 3) The power of
the TV is in standby mode (POWER indicator lights off).
When the TV is connected between two i.LINK devices in
series, select “Active” in “Standby Mode” or connect the
TV at an end of the series as shown in the diagram.
60
Using external equipment
Selecting an i.LINK device
• In order to control an i.LINK device from the TV, you
must first choose the i.LINK device to be controlled.
• One i.LINK device can be chosen from up to 16
i.LINK connected decks.
• All i.LINK devices connected with i.LINK cables
should automatically appear in the selection screen.
Press i.LINK to display the i.LINK control
panel.
Press a b c d/ / / to select “Model”, and
press ENTER.
• Selection screen appears.
Press a b/ to select a device, and then press
ENTER.
• The control panel for the i.LINK device appears.
1
2
3
Disabling the TV’s operation of an i.LINK device
•
By disabling the TV’s operation of an i.LINK device,
the device can be operated from another i.LINK device.
Press i.LINK to display the i.LINK control
panel.
Press abcd/ / / to select “Model”, and then
press ENTER.
• Selection screen appears.
1
2
3
NOTE
• Devices that cannot be used with this TV will not appear
in the selection screen.
• Depending on the i.LINK devices connected, the
manufacturer’s name and model name of some devices
may not display correctly.
• In the case where the manufacturer’s and model names
are not correctly displayed, disconnect the i.LINK cable.
Follow the procedure for “Deleting registered i.LINK
devices” and cancel all i.LINK devices you have registered
before reconnecting the i.LINK cable.
• When an item in the selection screen is grayed out, the
item is not recognized by the TV and cannot be selected.
(The item may not be connected properly.)
• The i.LINK device selected above will be automatically
set as a recording device in the TV Guide On Screen
system and may be used to record digital broadcasts.
• When there is no i.LINK device connected, the
message “No i.LINK model is available” appears. In
this case, please connect an i.LINK device. (See
page 58.)
• When there is no i.LINK device selected, the
selection screen appears. In this case, please go to
step 3.
• When there is no i.LINK device connected, “No
i.LINK model is available” appears. Please connect
an i.LINK device. (See page 58.)
• When there is no i.LINK device selected, the
selection screen appears. Please go to step 3.
Press b to select “Cancel Connection” and
then press ENTER.
• Operation of the i.LINK device from the TV is
disabled.
Model
Input
PWR
STOP
STOP 05
00:01:32
Model
Input
PWR
STOP
STOP 05
00:01:32
Type
i.LINK 1/1 [Thu] 1:33AM
Cancel Connection
Manufacturer
Which model do you use?
Model
Deleting registered i.LINK devices
• Registered i.LINK devices can be deleted from a
list.
• If an i.LINK device is connected, it cannot be deleted
from the list.
Press i.LINK to display the i.LINK control
panel.
Press abcd/ / / to select “Model”, and then
press ENTER.
Press a b/ to select a device to be deleted,
and then press ENTER.
1
2
3
Model
Input
PWR
STOP
STOP 05
00:01:32
Press c to select “Delete”, and then press
ENTER.
• The selected i.LINK device is deleted from the
list.
• Select “Cancel” if you do not want to delete
any device.
4
Type
i.LINK 1/1 [Thu] 1:33AM
Cancel Connection
Manufacturer
Which model do you use?
Model
Type
i.LINK 1/1 [Thu] 1:33AM
Cancel Connection
Manufacturer
Which model do you use?
Model
61
Using external equipment
Controlling an i.LINK device
• An i.LINK compatible device can be controlled from the TV using the i.LINK control panel on the screen.
• The steps in “i.LINK Setup” on page 59 need to be completed beforehand.
• Please also refer to the operation manual of the i.LINK device to be used with this TV.
Basic operation
1Press i.LINK to display the i.LINK control panel.
• The i.LINK button is also used to exit the i.LINK control panel.
2 abcdPress / / / to select a function, and then press ENTER.
i.LINK control panel (D-VHS decks)
NOTE
• The input selection button is used to select either i.LINK input or others.
• The EJECT button is displayed for Blu-ray Disc recorder only.
* Time: If you commence playback before Time is displayed, Time will not be displayed during the playback.
Model
Input
PWR
STOP
STOP 05
00:01:32
PWR
Cassette inserted
Function selected
with the cursor
Power On/Off
STOP
PLAY
PAUSE
REC START
SKIP BACK
REWIND
FAST FORWARD
SKIP FORWARD
Type of i.LINK
device
Type of videotape
i.LINK control panel (AV-HDD recorder/Blu-ray Disc recorder)
PWR
REC Oper.REC LIST
Model
Inputk30secl30sec
PWR
STOP
Free 61%
STOP 06
00:01:10 00:01:12/
k30sec
l30sec
REC LIST
Power On/Off
STOP
PLAY
PAUSE
GO TO REC LIST
SKIP BACK
REWIND
FAST FORWARD
SKIP FORWARD
REPEAT PLAYBACK
EJECT
30 SEC SKIP BACK
30 SEC SKIP FORWARD
Disk inserted
Function selected
with the cursor
Type of i.LINK
device
Remaining space
Manufacturer
Model
Go to REC operation screen
Select input
Current operation
Repeat status
Current counter
position/Time*
Go to Model Selection screen
Manufacturer
Model
Go to Model Selection screen
Select input
Current operation
Tape Counter
62
NOTE
• IEEE1394 is the IEEE’s international standard.
• i.LINK and the i.LINK logo are registered trademarks of
Sony Electronic, Inc.
• A copy protection technology is used on i.LINK devices
that incorporate copyright protection. This technology has
received the approval of the Digital Transmission Licensing
Administrator (DTLA), an organization that administers
copyright protection technologies. Some picture and
sound data have restrictions on duplication. Such data
cannot be digitally copied using the i.LINK. Some picture
and sound data may not be able to be sent back and
forth between an i.LINK device that has DTLA copyright
protection technology and one that does not.
Notes on i.LINK connection of D-VHS deck/AV-HDD
recorder/Blu-ray Disc recorder
• Even when a connected i.LINK device is playing, input
signal can be switched to input mode other than i.LINK
by shifting the cursor to the input selection button and
pressing ENTER.
• This TV may not be able to operate some i.LINK devices
using the control panel, or to display picture and/or sound
input from some i.LINK devices.
• When the TV’s control panel is used to record a program,
what is recorded with the i.LINK device are the pictures
and sound of the digital program that the TV is receiving.
• The i.LINK control panel cannot be used during timer
recording.
• There may be some programs which i.LINK devices
cannot record.
• With some i.LINK devices, the quality of the picture may
be distorted during fast forwarding or rewinding.
Notes specifically on i.LINK connection of D-VHS deck
• Depending on the D-VHS deck, this TV’s i.LINK may not
allow viewing of VHS and S-VHS tape or analog recorded
D-VHS tape. In this case, connect the D-VHS deck’s
analog output with the TV’s analog input, and switch the
TV’s input mode to external input.
• If a D-VHS deck is operated with the TV’s control panel
during timer recording, the recording may fail. Do not use
the TV’s control panel to operate the D-VHS deck during
timer recording.
• To record the picture and sound of a digital program which
the TV is receiving, use D-VHS tape. VHS or S-VHS tape
will not record.
Notes specifically on i.LINK connection of AV-HDD
recorder/Blu-ray Disc recorder
• Depending on the AV-HDD recorder and/or Blu-ray Disc
recorder, some functions, such as playback during
recording, display of the recording list screen during
recording, and so on, may not be able to be operated.
• Depending on the AV-HDD recorder and/or Blu-ray Disc
recorder, playback may stop automatically when switching
to another i.LINK device.
• If an AV-HDD recorder/Blu-ray Disc recorder is operated
with the TV’s control panel during timer recording, the
recording may fail. Do not use the TV’s control panel to
operate the AV-HDD recorder/Blu-ray Disc recorder during
timer recording.
Notes specifically on i.LINK connection of AV-HDD
recorder
• Depending on the AV-HDD recorder, it may be possible
to change the recorder’s operations mode (D-VHS mode,
HDD recorder mode). When the operations mode is D-
VHS mode, the HDD recorder is recognized as a D-VHS
Deck.
Using external equipment
Automatic input switching to i.LINK
• Input mode can be set to automatically switch to
i.LINK when an i.LINK device connected to the TV is
played.
Press MENU to display the MENU screen.
Press c d/ to select “Digital Setup”, and then
press ENTER.
Press a b/ select “i.LINK Autoswitch”, and
then press ENTER.
1
2
4
Press c d/ to select “Yes”, and then press
ENTER.
5
i.LINK Autoswitch
Standby Mode
Recording Mode
Yes No
Press a b/ to select “i.LINK Setup”, and then
press ENTER.
3
Recording digital programs with a D-VHS
deck (i.LINK)
• Before commencing this procedure, the steps in
“i.LINK Setup” on page 59 need to be completed
beforehand.
• Please also refer to the operation manual of the D-
VHS deck to be used with this TV.
Select a digital program to be recorded.
Press i.LINK to display the i.LINK control
panel.
Press abcd/ / / to select E, and then press
ENTER.
• Recording starts.
• Select H and press to stop recording.ENTER
1
2
3
NOTE
• Input mode cannot be switched to i.LINK during recording.
• When a D-VHS deck connected to the TV is under timer
recording, the deck cannot be operated using the TV’s
control panel.
Model
Input
PWR
STOP
STOP 05
00:01:32
63
Using external equipment
Recording digital programs with AV-HDD
recorder/Blu-ray Disc recorder
• Before commencing this procedure, the steps in
“i.LINK Setup” on page 59 need to be completed
beforehand.
• Please also refer to the operation manual of the AV-
HDD recorder/Blu-ray Disc recorder to be used with
this TV.
Press a b c d/ / / to select “REC Oper.”, and
then press ENTER.
Press a b/ /c d/ to select E, and then press
ENTER.
• Recording starts.
• Select “REC STOP” and press to stopENTER
recording.
3
4
NOTE
• Input mode cannot be switched to i.LINK during recording.
• When the input mode is i.LINK, you cannot operate
recording.
• When an AV-HDD recorder/Blu-ray Disc recorder
connected to the TV is under timer recording, the recorder
cannot be operated using the TV’s control panel.
Play Ope.
REC PAUSE
REC STOP
Model
Input
PWR
PLAY
OPE-
RATION
Free 61%
STOP 06
– – : – –: – –
Playing back using REC LIST (i.LINK)
• You can display a list of the programs you have
recorded on AV-HDD recorder and Blu-ray Disc.
Press i.LINK to display the i.LINK control
panel.
Press a b c d/ / / to select “REC LIST”, and
then press to display the REC LIST.ENTER
1
2
Press a b/ to select the desired program,
and then press ENTER.
Press c d/ to select “PLAY”, and then press
ENTER.
Press c d/ to select “From Top” or “From
current position”, and then press ENTER.
3
4
5
NOTE
• A program in the REC LIST may be deleted by performing:
Select the program Press Select “DELETE”sENTER s
on REC LIST Press Select “Delete” PresssENTER s s
ENTER
• A program in the REC LIST may be locked or unlocked
by performing:
Select the program Press Select “LOCK/sENTER s
UNLOCK” s Press ENTER
• Depending on the device connected, the audio and
images of the program selected with the cursor may not
be displayed in the small play screen.
• Depending on the device connected, when the recording
list is displayed during recording, the recording may stop.
• The program information displayed in the title (Program
name, date and time, etc.) will be taken from the program
information for the program broadcast at the time
recording commenced.
• When recording several programs in succession, the
program information displayed will be that of the first
program recorded at the time recording originally
commenced.
• When playing back content recorded on other devices,
the program information in the title may not be displayed
correctly in some cases.
Description
Playback will start from the beginning of the
selected program.
Playback will start from the point playback
stopped last time.
Selected item
From top
From current
position
Select a digital program to be recorded.
Press i.LINK to display the i.LINK control
panel.
1
2
06
Capacity: Free 61%
HD
HD
HD
HD
HD
PLAY DELETE LOCK/UNLOCK
64
Useful adjustment settings
Image position (AV input mode
only)
For adjusting a picture’s horizontal and vertical
position.
1
2
Press MENU and the MENU screen displays.
Press c d/ to select “Setup”.
4
5
3
Press a b/ to select “Position”, and then
press ENTER.
Press a b/ to select “H-Pos.” or “V-Pos.”.
Reset
H-Pos. –10 +10
V-Pos. –20 +20[ 0]
[ 0]
Press c d/ to adjust the item to your desired
position.
Description
Centers the image by moving it to the left
or right.
Centers the image by moving it up or
down.
Selected item
H-Pos.
V-Pos.
NOTE
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
•Adjustments are stored separately according to input
source.
• You can easily move the image position as shown on this
page, but when the power is switched off the image will
return to the previously memorized position.
Moving the picture on the screen
You can move the picture around on the screen.
Press a b c d/ / / to move an image on the screen to
the desired position. Press to return to the initialENTER
image position.
NOTE
• While pressing , an on-screen image,abcd///
“Adjusting Position” displays to the desired position.
• This setting cannot be stored. Once the TV shuts down or
enters standby mode, the setting is erased. To move the
picture around the screen again, you must perform the
above procedure again.
• The image position setting using the steps on this page
can be stored. Select either according to your objectives.
• “TV”, “INPUT1”, “INPUT2”, “INPUT3” and “INPUT4” can
each adjust the image position setting on this page. The
same for view modes.
• An on-screen image from PC cannot be moved around.
• Even when the image fills the screen, its position can be
adjusted with this function.
• Press ENTER to reset the image to original positions.
65
Useful adjustment settings
1
2
Auto Sync. adjustment (PC input
mode only)
For automatically adjusting the PC image.
Press MENU and the MENU screen displays.
Press c d/ to select “Setup”.
4
3
Press a b/ to select “Auto Sync.”, and then
press ENTER.
Press c d/ to select “Yes”, and then press
ENTER.
• Auto Sync. starts and “Now adjusting the
image” displays.
MENU
[Setup ... Auto Sync.]
NoYes
NOTE
• When Auto Sync. is successful, “Completed” displays. If
not, Auto Sync. failed.
• Auto Sync. may fail even if “Completed” displays.
• Auto Sync. may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing Auto Sync.
• Be sure to connect the PC to the TV and switch it on before
starting Auto Sync.
Fine Sync. adjustment (PC input
mode only)
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto Sync.
In some cases, however, manual adjustment is needed
to optimize the image.
Press MENU and the MENU screen displays.
Press c d/ to select “Setup”.
Press to select “Fine Sync.”, and thena b/
press ENTER.
Press c d/ to adjust the item to your
desired position.
NOTE
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
30%
Description
Centers the image by moving it to the left
or right.
Centers the image by moving it up or
down.
Adjust when the image flickers with vertical
stripes.
Adjust when characters have low contrast
or when the image flickers.
Selected item
H-Pos.
V-Pos.
Clock
Phase
Reset
H-Pos. [ 90] – +
V-Pos.
Clock
Phase
[ 39]
[ 90]
[ 20]
–
–
–
+
+
+
1
2
4
3
5
Press to select the specifica b/
adjustment item.
67
Useful adjustment settings
Input Label
Lets you set the input terminal displayed using the
INPUT SOURCE menu or channel display.
Press MENU and the MENU screen displays.
3
4
Press c d/ to select “Setup”.
Press a b/ to select “Input Label”, and then
press ENTER.
1
2
INPUT SOURCE
TV
CableBox [TV]
DVD
INPUT2
INPUT3
INPUT4
INPUT5INPUT5
i.LINK
Press a b c d/ / / to select the new name for
the channel, and then press ENTER.
(Example)
NOTE
• You cannot change labels if the INPUT SOURCE is TV, or
i.LINK.
Repeat steps 1 and 2 in Input Label.
1
2
Press a b/ to select the desired mode, and
then press ENTER.
Press a b/ to select “Picture Flip”, and then
press ENTER.
3
[Standard]: normal image.
[Mirror]: mirror image.
ABC
ABC
ABC
ABC
[Upside Down]: upside down image.
[Rotate]: rotated image.
Picture Flip
You can set the orientation of the picture.
68
Useful adjustment settings
AV MODE
AV MODE gives you six viewing options to choose
from to best match environment of the TV, which can
vary due to factors like room brightness, type of
program watched or the type of image input from
external equipment.
Description
For a highly defined image in a normally
bright room
For a movie
Lowers image brightness for easier viewing
Allows the user to customize settings as
desired. You can set the mode for each
input source.
Changing image and sound settings to
factory preset values. No adjustments are
allowed.
For a clear-cut image emphasizing high
contrast for sports viewing
Selected item
STANDARD
MOVIE
GAME
USER
DYNAMIC
(Fixed)
DYNAMIC
Press AV MODE.
• Present AV MODE displays.
Press AV MODE again before the mode
displayed on the screen disappears.
• The mode changes as shown below.
1
2
Mode selection for TV, INPUT 1 to 5 and i.LINK mode
(Example)
Mode selection for the PC terminal
(Example)
AV MODE: MOVIE
AV MODE: STANDARD
AV MODE: DYNAMIC AV MODE: GAME
AV MODE: USER AV MODE: DYNAMIC (Fixed)
AV MODE: STANDARD AV MODE: USER [PC]
View mode for 4:3 Programs
Press VIEW MODE.
• The View mode menu displays.
• The menu lists the view mode options
selectable for the type of video signal currently
received.
Side Bar: Suitable for viewing
conventional 4:3 programs
in their normal format.
S.Stretch: Suitable for stretching 4:3
programs to fill the screen.
Zoom: Suitable for viewing wide-
screen 2.35:1 anamorphic
DVDs in full screen.
Stretch: This mode is useful for
1.78:1 DVDs.
When viewing 1.85:1
DVDs, stretch mode will
still show very thin black
bands at the top and
bottom of the screen.
(Smart
stretch)
1
2
Press VIEW MODE or a b/ while the View
mode menu is still on the screen.
• You can sequentially select a view mode that
has its own aspect ratio.
View Mode
Side Bar
S. Stretch
Zoom
Stretch
NOTE
• You can select a different AV MODE item for each input
mode. (For example, select STANDARD for TV input and
DYNAMIC for VIDEO input.)
View mode for HD Programs
The following modes are available for HD programs.
Suitable for viewing wide-screen 1.78:1 aspect-
ratio programs.
When viewing 1.85:1 programs, stretch mode
will still show very thin black bands at the top
and bottom of the screen.
Stretch:
Detects the resolution of the signal and
displays an image with the same number of
pixels on the screen.
Dot by Dot:
Suitable for stretching 4:3 programs to fill the
screen.
S.Stretch:
(Smart
stretch)
Suitable for viewing wide-screen 2.35:1 aspect-
ratio programs in full screen.
Zoom:
NOTE
• When using Dot by Dot, it is possible to see noise or bars
around different outer portions of the screen. Please
change view mode to correct this.
69
Useful adjustment settings
View mode (for PC input mode)
You can select the screen size.
a
View Mode
Normal
Stretch
Dot by Dot
Zoom
Input signal Normal Zoom Stretch Dot by Dot
Keeps the original
aspect ratio in a full
screen display.
Keeps the original
aspect ratio in a full
screen display. The
top and bottom of
the image is slightly
cropped.
An image fully fills
the screen.
Detects the
resolution of the
signal and
displays an image
with the same
number of pixels
on the screen.
a
Screen size images.
NOTE
• Connect the PC before making adjustments. (See page
57.)
• Selectable screen size may vary with input signal type.
Press VIEW MODE.
• The View mode menu displays.
1
2
Press VIEW MODE or a b/ to select a
desired item on the menu.
70
Useful adjustment settings
Press MENU and the MENU screen displays.
1
2
Press a b/ to select “Input Signal” and then
press ENTER.
3
Press c d/ to select “Setup”.
Press a b/ to select the desired input signal
on the display.
4
640 x 480
848 x 480
Example
Input signal (for PC input mode)
• Some input signals may have to be registered manually
to display properly.
• The pairs of input signals (resolutions) in the list below
are not distinguishable when received. In such case, you
have to set the correct signal manually. After setting once,
it will display when the same signal (resolution) is input
again.
NOTE
• You can only select the “Input Signal” on the Setup menu
when receiving one of the 6 input signals listed above.
Digital Noise Reduction
Produces a clearer video image.
1
2
3
Press MENU and the MENU screen displays.
Press c d/ to select “Option”.
Press a b/ to select “Digital Noise
Reduction”, and then press ENTER.
Press a b/ to select the desired level, and
then press ENTER.
4
Off
High
Low
720 400g
848 480g
1280 768g
640 400g
640 480g
1024 768g
Audio Only
When listening to music from a music program, you
can set the Liquid Crystal display off and enjoy audio
only.
Press c d/ to select “On”, and then press
ENTER.
Repeat steps 1 and 2 in Digital Noise
Reduction.
Press a b/ to select “Audio Only”, and then
press ENTER.
1
2
3
Description
Audio is output without screen image.
Both screen images and audio are output.
Selected item
On
Off
71
Useful adjustment settings
Description
• Sound via speaker is adjusted with VOL
k l l/ on the remote control unit or VOL /
k on the TV.
• Sound via the MONITOR OUT terminal is
not adjustable and constantly outputs.
• Sound via the MONITOR OUT terminal is
adjusted with on the remoteVOL k l/
control unit or on the TV.VOL l k/
• Sound via speaker is muted.
Selected item
Fixed
Variable
Output Select
Allows you to select what controls the audio output.
Press MENU and the MENU screen displays.
1
2
Press a b/ to select “Output Select”, and
then press ENTER.
3
Press c d/ to select “Fixed” or “Variable”,
and then press ENTER.
4
Press c d/ to select “Option”.
Quick Shoot
Use Quick Shoot to view fast-action video more clearly.
1
2
3
Repeat steps 1 and 2 in Output Select.
Press a b/ to select “Quick Shoot”, and then
press ENTER.
Press c d/ to select “On”, and then press
ENTER.
NOTE
• If video noise occurs, turn the function “Off”.
Sleep Timer
Allows you to set a time when the TV automatically
switches to standby.
Sleep Timer: Off
30
60
90
120
Sleep Timer:
Sleep Timer:
Sleep Timer:
Sleep Timer:
1
2
Press SLEEP.
• Remaining time displays when sleep timer has
been set.
Each time you press , the remainingSLEEP
time switches as shown below.
• When set, the time automatically starts counting
down.
• If you want to adjust the sleep timer, you can
press SLEEP twice then change the time
setting.
• Five minutes before time expires, the remaining
time displays each minute.
NOTE
• Select “Off” by pressing to cancel the sleep timer.SLEEP
• The TV will enter the standby mode when the remaining
time reaches zero.
Sleep Timer: Remaining 30
73
Useful adjustment settings
Closed Captions and Digital Closed
Captions
• Your TV is equipped with an internal Closed Caption
decoder. It allows you to view conversations,
narration and sound effects as subtitles on your TV.
Closed Captions are available on some TV programs,
and on some VHS home video tapes, at the election
of the program provider.
• Digital Closed Caption service is a new caption
service available only on digital TV programs (also
at the election of the service provider). It is a more
flexible system than the original Closed Caption
system, because it allows a variety of caption sizes
and font styles. When the Digital Closed Caption
service is in use, it will be indicated by appearance
of a 3-letter abbreviation that also indicates the
language of the Digital Closed Captions: ENG
(English) or SPA (Spanish) or FRA (French), or other
language codes.
• Not all programs and VHS videotapes offer closed
caption. Please look for the “ ” symbol to ensureN
that captions will be shown.
• In the Closed Caption system, there can be more
than one caption service provided. Each is identified
by its own number. The “CC1” and “CC2” services
display subtitles of TV programs superimposed over
the program’s picture.
• In the Closed Caption system, the “Text1” or “Text2”
services display text that is unrelated to the program
being viewed (e.g., weather or news). These
services are also superimposed over the program
currently being viewed.
2
Air ANALOG
Audio : MONO
CC : 1/2 CC1
Closed Caption
information
1
2
Press CC.
• This will present the Closed Caption information
display.
Press CC while the Closed Caption
information is still on the screen.
• Press repeatedly until you select a closed
caption service which you prefer.
• Depending on the number of caption services
in the signal being received, you will see
information such as 1/2 or 1/4 displayed.
1/2 means “the first of two services”.
Example:
If a program has three services (Digital
CC(ENG), CC1 and Text1), the closed caption
display will toggle in this sequence:
1/3 ENG 2/3 CC1 3/3 Text1 OFF
• The CC button keeps a record of the last service
selected in its memory.
If the last closed caption mode (e.g. 1/3ENG)
you selected is not available for the next
program, or on another channel, the closed
caption service that is available is automatically
selected, and this service appears in
parentheses, e.g.1/3(CC1).
Closed caption services that appear in
parentheses will not be recorded in the CC
button’s memory as your last selected service.
Only services that you have selected with the
CC button are recorded.
Examples:
In a case where there are two closed caption
services provided, (for instance, Digital CC(ENG)
and CC1), and Digital CC(ENG) is displayed as
your current selection, if Digital CC(ENG) is not
broadcast for the next program, the other closed
caption service, CC1, will be displayed in
parentheses.
A closed caption service appears in parentheses
because the service you selected is not available
and a different service is displayed on your
screen. “1/1(CC1)” is displayed instead of “1/2/
ENG”.
NOTE
• See page 74 to 76 for detailed closed caption settings.
• When using Freeze functions, closed captions will not be
displayed on the right-most screen (still image).
• When the program contains no closed caption, “--”
displays in the closed caption information.
• If the language code, e.g. “ENG”, is not found on Digital
TV programs, “--” will be shown.
• Four kinds of closed caption service (CC1, CC2, Text1,
Text2) are potentially available, but a broadcast may
contain none, or only some of these services, at the
election of the program provider.
74
Useful adjustment settings
Caption Size
Select a caption size.
4
Press a b/ to select “Caption Size”.
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Option”.
3
Press a b/ to select “Caption Setup”, and
then press ENTER.
Caption Size Default
Font Style Default
Foreground Color Default
Foreground Opacity Default
Background Color Default
Background Opacity Default
Character Edge Default
Reset
ABC
123
Font Style
Select a font style.
Press a b/ to select “Font Style”.
4
Press c d/ to select the desired style.
5
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Option”.
3
Press a b/ to select “Caption Setup”, and
then press ENTER.
5
Press c d/ to select the desired size.
Description
The font specified by broadcasting station
or default font.
Proportional font used in the MENU screen.
Monospaced with serifs.
Proportionally spaced with serifs.
Monospaced without serifs.
Proportionally spaced without serifs.
Casual font type.
Cursive font type.
Small capitals.
Selected item
Default
Type 0
Type 1
Type 2
Type 3
Type 4
Type 5
Type 6
Type 7
NOTE
• Default: The caption size specified by broadcasting station
or default size.
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
NOTE
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
75
Useful adjustment settings
Foreground Color
Select a character foreground color.
4
Press a b/ to select “Foreground Color”.
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Option”.
3
Press a b/ to select “Caption Setup”, and
then press ENTER.
Caption Size Default
Font Style Default
Foreground Color Default
Foreground Opacity Default
Background Color Default
Background Opacity Default
Character Edge Default
Reset
A B C
123
Foreground Opacity
Select a foreground opacity value.
Press a b/ to select “Foreground Opacity”.
Press c d/ to select the desired value.
Repeat steps 1 to 3 in Foreground Color.
1
2
3
5Press c d/ to select the desired color.
NOTE
• Default: The foreground color specified by broadcasting
station or default color.
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
NOTE
• Default: The foreground opacity value specified by
broadcasting station or default opacity value.
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
Background Color
Select a character background color.
Press a b/ to select “Background Color”.
Repeat steps 1 to 3 in Foreground Color.
1
2
3
Press c d/ to select the desired color.
NOTE
• Default: The background color specified by broadcasting
station or default color.
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
76
Useful adjustment settings
Background Opacity
Select a background opacity value.
Press a b/ to select “Background Opacity”.
4
Press c d/ to select the desired value.
5
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Option”.
3
Press a b/ to select “Caption Setup”, and
then press ENTER.
Caption Size Default
Font Style Default
Foreground Color Default
Foreground Opacity Default
Background Color Default
Background Opacity Default
Character Edge Default
Reset
A B C
123
NOTE
• Default: The background opacity value specified by
broadcasting station or default opacity value.
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
Character Edge
Select a character edge.
4
Press a b/ to select “Character Edge”.
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Option”.
3
Press a b/ to select “Caption Setup”, and
then press ENTER.
5
Press c d/ to select the desired setting.
NOTE
• Default: The character edge specified by broadcasting
station or default edge.
• For resetting all adjustment items to the factory preset
values, press to select “Reset”, and then pressa b/
ENTER.
77
Useful adjustment settings
Secret number setting for parental
control (AV input mode only)
Allows you to use a secret number to protect certain
settings from being accidentally changed.
IMPORTANT:
Three conditions must be met to enable V-Chip (see
pages 77 to 83):
1 Secret No. is registered.
2 V-Chip settings have been made.
3 “Status” is set to “On”.
Press MENU and MENU screen displays.
1
2
Press c d/ to select “Setup”.
Press a b/ to select “Parental CTRL”, and
then press ENTER.
3
Press a b/ to select “Secret No.”, and then
press ENTER.
4
V-Chip
Secret No.
Status
MENU [Setup ... Parental CTRL ... Secret No. ]
Select “New Secret No.”, and then press
ENTER.
Input the new 4-digit secret number by using
0 9 – .
5
New Secret No.
Secret No. Clear
New Secret No. ––––
Input Secret No. ––––
Reconfirm ––––
Input the same 4-digit number on the
“Reconfirm” screen as in step 5 to confirm.
6
New Secret No.
Secret No. Clear
New Secret No. ****
Input Secret No.
––––Reconfirm
––––
Setting parental control status
Used to enable or disable the parental control function.
Press a b/ to select “Status”, and then press
ENTER.
Press c d/ to select “On” or “Off”, and then
press ENTER.
• Select “On” to enable and “Off” to disable
Parental CTRL.
V-Chip
Secret No.
Status
On Off
Repeat steps 1 to 3 in Setting a secret
number.
• Secret number setting menu displays.
1
2
Input the 4-digit secret number by using 0 –
9.
3
4
Press RETURN to start configuring V-Chip
settings. (See pages 80 and 82 for details.)
7
Setting a secret number
NOTE
• You can skip step 1 and 2 above while in Parental CTRL
screen.
78
Useful adjustment settings
Changing the secret number
Allows you to change your current secret number.
Repeat steps 1 to 3 in Setting a secret
number.
• Secret number setting menu displays.
1
3
Press a b/ to select “New Secret No.”, and
then press ENTER.
Input the old 4-digit number you have set
using 0 – 9.
MENU [Setup ... Parental CTRL ... Secret No. ]
New Secret No.
Secret No. Clear
New Secret No. ––––
Input Secret No. ––––
Reconfirm ––––
Input the new 4-digit number using 0 – 9.
Input the same 4-digit number on the
“Reconfirm” screen as in step 6 to confirm.
Clearing the secret number
Allows you to clear your secret number.
Repeat steps 1 to 3 in Setting a secret
number.
• Secret number setting menu displays.
1
2
Input the 4-digit secret number by using 0 –
9.
3
5
4
Press a b/ to select “Secret No.”, and then
press ENTER.
Press c d/ to select “Yes”, and then press
ENTER.
• Your secret number is cleared.
Press a b/ to select “Secret No. Clear”, and
then press ENTER.
NOTE
• See page 77 for re-registering with a new secret number
after being cleared.
• As a precautionary measure, make a note of your
secret number and keep it in a familiar place. If you
lose or forget your secret number, initialize the
Liquid Crystal Television to return all settings except
for the TV channel settings to factory preset values.
(See page 98.)
• If the secret number is cleared the Status setting
automatically sets to “Off”. “V-Chip” and “Status” will not
be selectable from the menu.
New Secret No.
Secret No. Clear
Yes No
Press a b/ to select “Secret No.”, and then
press ENTER.
New Secret No.
Secret No. Clear
New Secret No. ––––
Input Secret No. ––––
Reconfirm ––––
4
5
6
7
New Secret No.
Secret No. Clear
New Secret No. ****
Input Secret No.
––––
Reconfirm
––––
2
Input the 4-digit secret number by using 0 –
9.
79
Useful adjustment settings
Parental control (setting V-CHIP level)
V-CHIP is an electronic filtering device built into your TV. This tool gives parents a great degree of control over
broadcasts accessed by their children. It allows parents to select programs judged suitable for child viewing
while blocking ones judged not suitable. It does so automatically once you activate the V-CHIP feature in your
Liquid Crystal Television.
“V-Chip” and “Status” will not be selectable from the menu if you do not first configure your secret
number. (See page 77 for Secret number setting for parental control.)
• The U.S. has two rating systems for viewing content: TV Parental Guidelines and movie ratings.
• The TV Parental Guidelines work in conjunction with the V-CHIP to help parents screen out inappropriate
television shows from their children.
• Movie ratings are used for original movies rated by the Motion Picture Association of America (MPAA) as
watched on cable TV and not edited for television. The V-CHIP can also be set to block MPAA-rated movies.
Voluntary movie rating system (MPAA)
Rating
Age
G
PG
PG-13
R
NC-17
X
General audiences. All ages admitted.
Parental guidance suggested. Some material may not be suitable for children.
Parents strongly cautioned. Some material may be inappropriate for children under 13.
Restricted. Under 17 requires accompanying parent or adult guardian (age varies in some
jurisdictions).
No one 17 and under admitted.
X is an older rating that is unified with NC-17 but may be encoded in the data of older movies.
Description
X: Content rating can be set.
TV Parental Guidelines
TV-Y (All children)
TV-Y7 (Directed to older children)
TV-G (General audience)
TV-PG (Parental Guidance suggested)
TV-14 (Parents strongly cautioned)
TV-MA (Mature audience only)
Rating
Suggested
age
Content
FV
(Fantasy
violence)
V
(Violence)
S
(Sexual
situation)
L
(Adult
language)
D
(Sexually
suggestive
dialog)
X
X
X
X
X
X
X
X
X
X
X
X
a
• If you select “PG-13”, this will automatically block the higher ratings
“R”, “NC-17” and “X”.
NOTE
• Voluntary movie rating system only uses an age-based rating.
MENU [Setup ... Parental CTRL ... V-Chip]
MPAA
TV Guidelines
Can. English Ratings
Can. French Ratings PG-13
R
NC-17
X
NONE
PG
G
80
Useful adjustment settings
Voluntary movie rating system (MPAA)
Press MENU and the MENU screen displays.
1
2
Press c d/ to select “Setup”.
Input the 4-digit secret number by using 0 –
9.
3
Press a b/ to select “Parental CTRL”, and
then press ENTER.
• Secret number setting menu displays only
when “Secret No.” is set. (See page 77.)
• “V-Chip” and “Status” will not be selectable
from the menu if you do not first configure your
secret number. (See page 77.)
5
Press a b/ to select “V-Chip”, and then press
ENTER.
6
V-Chip
Secret No.
Status
MENU [Setup ... Parental CTRL ... V-Chip]
Press a b/ to select “MPAA”, and then press
ENTER.
Press a b/ to adjust the item to your desired
position. “ ” indicates the item is blocked.
Press RETURN.
• The setting automatically enters “Block” for any
ratings below your selection.
• If Status is not set to “On” the configuration
settings will not work. (See page 77.)
7
MPAA
TV Guidelines
Can. English Ratings
Can. French Ratings PG-13
R
NC-17
X
NONE
PG
G
TV Parental Guidelines (TV Guidelines)
Repeat steps 1 to 5 in Voluntary movie
rating system (MPAA).
1
2
Press a b/ to select “TV Guidelines”, and
then press ENTER.
Press a b/ to adjust the item to your desired
position. “ ” indicates the item is blocked.
• The setting automatically enters “Block” for any
ratings below your selection.
3
MPAA
TV Guidelines
Can. English Ratings
Can. French Ratings L
S
V
FV
D
TV-G
TV-PG
TV-14
TV-MA
NONE
TV-Y7
TV-Y
When setting an individual content-based rating
item, do as follows:
1 dPress to access block content items from
the currently selected age-based rating item.
2 a bPress / to select an individual item, and
then press to unblock (“ENTER ” is
removed). Repeat the same steps for other
items.
3 cPress or to register after allRETURN
individual content rating items are set.
MPAA
TV Guidelines
Can. English Ratings
Can. French Ratings L
S
V
FV
D
TV-G
TV-PG
TV-14
TV-MA
NONE
TV-Y7
TV-Y
4
Example
Example
Example
• If Status is not set to “On” the configuration
settings will not work. (See page 77.)
81
Useful adjustment settings
Canadian Rating Systems
• The TV rating systems in Canada are based on the Canadian Radio-Television and Telecommunications
Commission (CRTC) policy on violence in television programming.
• While violence is the most important content element to be rated, the structure developed takes into
consideration other program content like language, nudity, sexuality and mature themes.
• When setting the V-CHIP on the Canadian system you can choose either the Canadian English ratings or the
Canadian French ratings.
Rating
Age
E
C
C8e
G
PG
14e
18e
Exempt: Includes news, sports, documentaries and other information programming; talk
shows, music videos, and variety programming.
Children: Intended for younger children under the age of 8 years. Pays careful attention to
themes that could threaten their sense of security and well-being.
Children over 8 years old: Contains no portrayal of violence as the preferred, acceptable,
or only way to resolve conflict; nor encourage children to imitate dangerous acts which
they may see on the screen.
General: Considered acceptable for all age groups. Appropriate viewing for the entire
family, contains very little violence, physical, verbal or emotional.
Parental Guidance: Intended for a general audience, but may not be suitable for younger
children (under the age of 8) because it could contain controversial themes or issues.
Over 14 Years: Could contain themes where violence is one of the dominant elements of
the storyline, but it must be integral to the development of plot or character. Language
usage could be profane and nudity present within the context of the theme.
Adults: Intended for viewers 18 years and older and might contain depictions of violence,
which while related to the development of plot, character or themes, are intended for adult
viewing. Could contain graphic language and portrayals of sex and nudity.
Description
Canadian English ratings
Rating
Age
E
G
8anse
13anse
16anse
18anse
Exempt programming.
General: All ages and children, contains minimal direct violence, but may be integrated
into the plot in a humorous or unrealistic manner.
General but inadvisable for young children: May be viewed by a wide public audience, but
could contain scenes disturbing to children under 8 who cannot distinguish between
imaginary and real situations. Recommended for viewing with parent.
Over 13 years: Could contain frequent violent scenes and therefore recommended for
viewing with parent.
Over 16 years: Could contain frequent violent scenes and intense violence.
Over 18 years: Only for adult viewing. Could contain frequent violent scenes and extreme
violence.
Description
Canadian French ratings
Product specificaties
| Merk: | Sharp |
| Categorie: | Televisie |
| Model: | LC-32D7U |
Heb je hulp nodig?
Als je hulp nodig hebt met Sharp LC-32D7U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Televisie Sharp
9 Maart 2025
9 December 2024
9 December 2024
9 December 2024
9 December 2024
16 November 2024
9 November 2024
9 November 2024
9 November 2024
8 November 2024
Handleiding Televisie
- Televisie Electrolux
- Televisie Philips
- Televisie Sony
- Televisie Samsung
- Televisie Xiaomi
- Televisie Casio
- Televisie Panasonic
- Televisie LG
- Televisie AEG
- Televisie BEKO
- Televisie Daewoo
- Televisie Grundig
- Televisie JVC
- Televisie Medion
- Televisie Nokia
- Televisie Pioneer
- Televisie Siemens
- Televisie Toshiba
- Televisie Xiron
- Televisie Yamaha
- Televisie Abus
- Televisie Acer
- Televisie Ag Neovo
- Televisie Airis
- Televisie Aiwa
- Televisie Akai
- Televisie Albrecht
- Televisie Alden
- Televisie Aldi
- Televisie Allview
- Televisie Alphatronics
- Televisie AOC
- Televisie Apex
- Televisie Arcelik
- Televisie Aristona
- Televisie Audiosonic
- Televisie Avtex
- Televisie Bang Olufsen
- Televisie Belson
- Televisie BenQ
- Televisie Blaupunkt
- Televisie Bluesky
- Televisie Brandt
- Televisie Daitsu
- Televisie Dell
- Televisie Denver
- Televisie Difrnce
- Televisie Digihome
- Televisie Dual
- Televisie Durabase
- Televisie Dyon
- Televisie E-motion
- Televisie Emerson
- Televisie Energy Sistem
- Televisie Engel
- Televisie Fantec
- Televisie Ferguson
- Televisie Finlux
- Televisie Fujitsu
- Televisie Funai
- Televisie GPX
- Televisie Graetz
- Televisie Haier
- Televisie Hannspree
- Televisie Hisense
- Televisie Hitachi
- Televisie HKC
- Televisie Hoher
- Televisie Horizon
- Televisie Humax
- Televisie Hyundai
- Televisie Icy Box
- Televisie Iiyama
- Televisie ILive
- Televisie Innoliving
- Televisie Insignia
- Televisie Intenso
- Televisie ITT
- Televisie Kogan
- Televisie Kuppersbusch
- Televisie Lenco
- Televisie Lenovo
- Televisie Lexibook
- Televisie Loewe
- Televisie Logik
- Televisie Luxor
- Televisie Magnavox
- Televisie Magnum
- Televisie Manhattan
- Televisie Manta
- Televisie Marantz
- Televisie Marquant
- Televisie Megasat
- Televisie Metz
- Televisie Mitsubishi
- Televisie Mpman
- Televisie MT Logic
- Televisie Muse
- Televisie Mx Onda
- Televisie Nabo
- Televisie Nec
- Televisie Nedis
- Televisie Newstar
- Televisie Nextbase
- Televisie Nikkei
- Televisie Nordmende
- Televisie Packard Bell
- Televisie Peaq
- Televisie Philco
- Televisie Polar
- Televisie Polaroid
- Televisie Premier
- Televisie Proline
- Televisie Pyle
- Televisie Qilive
- Televisie RCA
- Televisie Reflex
- Televisie Reflexion
- Televisie Rm 2000
- Televisie Roadstar
- Televisie Saba
- Televisie Sagem
- Televisie Salora
- Televisie Sanyo
- Televisie Sbr
- Televisie Schaub Lorenz
- Televisie Schneider
- Televisie Seg
- Televisie Selfsat
- Televisie Sencor
- Televisie Silvercrest
- Televisie Sogo
- Televisie Soundmaster
- Televisie Strong
- Televisie Sunny
- Televisie Sunstech
- Televisie Superior
- Televisie Sweex
- Televisie Sylvania
- Televisie TCL
- Televisie Teac
- Televisie TechLine
- Televisie Technika
- Televisie Technisat
- Televisie Techwood
- Televisie Tele 2
- Televisie Teleco
- Televisie Telefunken
- Televisie Terris
- Televisie Tesla
- Televisie Tevion
- Televisie Thomson
- Televisie Time
- Televisie Tve
- Televisie Uniden
- Televisie United
- Televisie Vestel
- Televisie Viewpia
- Televisie Viewsonic
- Televisie Vision Plus
- Televisie Vivax
- Televisie Vivo
- Televisie Vizio
- Televisie Voxx
- Televisie Walker
- Televisie Westinghouse
- Televisie Wharfedale
- Televisie Woxter
- Televisie Xoro
- Televisie Yasin
- Televisie Zalman
- Televisie Ziggo
- Televisie Jay-tech
- Televisie Jensen
- Televisie JGC
- Televisie JTC
- Televisie Odys
- Televisie OK
- Televisie Oki
- Televisie Online
- Televisie Onn
- Televisie Opera
- Televisie Oppo
- Televisie Optoma
- Televisie Orion
- Televisie Oyster
- Televisie Changhong
- Televisie Clatronic
- Televisie Continental Edison
- Televisie ECG
- Televisie Palsonic
- Televisie Vox
- Televisie Bang And Olufsen
- Televisie GoGEN
- Televisie Krüger And Matz
- Televisie Naxa
- Televisie Proscan
- Televisie Voxicon
- Televisie Kunft
- Televisie Aspes
- Televisie AYA
- Televisie Bush
- Televisie High One
- Televisie Infiniton
- Televisie Kernau
- Televisie Nevir
- Televisie Orima
- Televisie Svan
- Televisie Grunkel
- Televisie SereneLife
- Televisie Zenith
- Televisie Citizen
- Televisie Kubo
- Televisie Smart Brand
- Televisie Alba
- Televisie Edenwood
- Televisie Elbe
- Televisie Majestic
- Televisie Trevi
- Televisie Cello
- Televisie NPG
- Televisie Orava
- Televisie Star-Light
- Televisie Videocon
- Televisie Cecotec
- Televisie Bauhn
- Televisie MBM
- Televisie Furrion
- Televisie Coby
- Televisie Doffler
- Televisie DGM
- Televisie Planar
- Televisie Chiq
- Televisie Monster
- Televisie Antarion
- Televisie Felson
- Televisie SEIKI
- Televisie SunBriteTV
- Televisie Tucson
- Televisie CGV
- Televisie LTC
- Televisie Caratec
- Televisie Séura
- Televisie AudioAffairs
- Televisie Element
- Televisie Peerless-AV
- Televisie XD Enjoy
- Televisie Inovia
- Televisie DirecTV
- Televisie Telesystem
- Televisie Kemo
- Televisie EKO
- Televisie Mitsai
- Televisie V7
- Televisie ISymphony
- Televisie Pantel
- Televisie ATYME
- Televisie HCI
- Televisie Inno-Hit
- Televisie Lin
- Televisie Elements
- Televisie Englaon
- Televisie Astar
- Televisie Visco
- Televisie Tivax
- Televisie H&B
- Televisie Norcent
- Televisie TELE System
- Televisie TIM
- Televisie Kivi
- Televisie Mach Power
- Televisie Axing
- Televisie FFalcon
- Televisie Smart Tech
- Televisie Mitzu
- Televisie JTC24
- Televisie Coocaa
- Televisie SYLVOX
- Televisie RevolutionHD
- Televisie FOX Electronics
- Televisie QBell Technology
- Televisie Aconatic
- Televisie Mitchell & Brown
- Televisie Mystery
- Televisie Linsar
Nieuwste handleidingen voor Televisie
25 Maart 2025
18 Maart 2025
18 Maart 2025
12 Maart 2025
12 Maart 2025
12 Maart 2025
12 Maart 2025
12 Maart 2025
12 Maart 2025
11 Maart 2025