SentrySafe TC8-331 Handleiding

SentrySafe Kluis TC8-331

Lees hieronder de 📖 handleiding in het Nederlandse voor SentrySafe TC8-331 (16 pagina's) in de categorie Kluis. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

Fire-Safe

® BRAND

Security Safe

Owner’s Manual

Manuel du

propriétaire

du coffre-fort de

sécurité DE MARQUE

Fire-Safe

Manual del propietario

de la caja fuerte de

seguridad Fir

e-S

afe

MARCA

TABLE OF CONTENTS

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2- 5

French. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10

Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15

TABLE DES MATIÈRES

Anglais. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -5

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

Espagnol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-15

ÍNDICE

Inglés . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2- 5

Francés. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-15

Thank you for purchasing this

Sentry Fire-Safe® product.

For safes with electronic lock:

Model TC8-331

Battery Installation

To power the lock, four alkaline AA batteries (not included) are

required.

NOTE: Non-alkaline and rechargeable batteries ARE

NOT RECOMMENDED.

To install batteries, turn the electronic lock case to the left and

remove. (Fig. A) Unlock door with the override key provided in

the plastic bag attached to the owner’s manual, and open the

door using the lever handle. Remove key hook plate located on

the inside back of the door by sliding the plate upward, then

pulling toward you. (Fig. B) Insert the four batteries as indicated.

Replace the key hook plate and keypad.

Model TW8-331

Battery Installation

To power the lock, four alkaline AA batteries equaling voltage:

6Vdc, (not included) are required.

NOTE: Non-alkaline and rechargeable batteries ARE

NOT RECOMMENDED.

To install batteries, turn the electronic lock case to the left and

remove. (Fig. A) Insert four new batteries as indicated, replace

the electronic lock case and turn to the right to reassemble.

For all models, test first

with door open!

(See back cover of this manual for your factory code.)

Test your combination several times with the door open.

NOTE: All electronic lock units have been provided

with an override key (skeleton key). Some

electronic units are equipped with a handle

OR electronic lock and key.

1. Insert the four-bitted key into the lock to the left of the

key pad. (Be sure key lock is turned as far left

as possible.)

2. Press the five-digit factory code. The green light will

come on.

3. For units with key, turn the key to the right.

4. Open the door.

Using the keypad

Only a light touch is needed. A green PROCEED light and a

single beep indicate that the keypad “felt” your touch. The lock

allows 5 seconds for each key press. If you pause longer, an error

signal will occur (blinking red light and three beeps), indicating

you should start over.

Models TC8-331 and TW8-331

Access Codes

There are three possible ways to unlock and access the safe—

by entering its preset Factory Code, your own User Code

or a Passcode.

You can always open the safe by entering the 5-digit Factory

Code. But if you prefer to use your own code, you can program

the safe to open to the 5-digit User Code of your choice. If you

wish to give someone else temporary access to the safe, you can

program a passcode that can later be erased.

Programming a user code

There are two ways to program a user code.

A 1. Press the Program key.

2. Enter the Factory Code. The green LED remains ON while

you enter the 5-digit user code of your choice. After 5 digits

are entered the green LED turns OFF.

(To enter a new User Code, repeat these steps.)

B 1. Press the red button inside the safe. The lock will “beep”

and the green LED will come on.

2. Enter a 5-digit user code.

(To enter a new User Code, repeat these steps.)

Programming a passcode

1. Press the Program key twice.

2. Enter your 5-digit User Code. The green LED remains ON.

3. Enter the 5-digit passcode of your choice (any combination

except 00000.) After 5 digits are entered, the green LED

turns OFF.

(To enter a new passcode, repeat these steps. To erase the

passcode, press Program twice, enter your User Code and then

enter 00000.)

Unlocking

To unlock the safe, you must enter a valid Factory Code,

User Code or Passcode. Once you have done this, you have

4 seconds to open the safe by turning the handle or 4-bitted key

to the unlock position. If you fail to do so in time, the lock will

reactivate.

(If you realize you have made an error while entering your code,

press the CLEAR button and start over.)

FloodGuardTM

Water-resistance protection

For those models with water resistance (TW models), which

have been tested by the independent testing firm ETL SEMKO

and certified to be in compliance with the manufacturer’s

specifications for water-resistant protection. Products were

immersed in up to 1’ of water for up to 72 hours and withstood

water leakage.

Water-resistant models must be bolted down.

The supplied hardware MUST BE USED to bolt the

safe to the floor to assure the watertight seal, or the

water-resistant claim is invalid.

NOTE: It is normal to feel a slight amount of resistance

when closing the door and locking water-

resistant models.

NOTE: Sentry Group is not responsible for any costs

incurred if unit is to be replaced.

Instructions for floor mounting

This kit contains:

• (2) lag screws

• (2) rubberized washers

• (2) masonry anchors

Required tools:

• Drill

• Wrench

• For wood anchoring: 7/16˝ (11.0 mm) drill bit

• For masonry anchoring: 7/16˝ (11.0 mm) masonry drill bit

Instructions

1. Unlock the safe and open the door.

2. Use a screw or drill bit to mark the floor through both holes.

3. Move the safe aside to clear both marked spots for drilling.

4. Drill into the floor:

• For wood: Using the 7/16˝ (11.0 mm) drill bit drill a hole

2 1/2˝(64.0 mm) deep in each marked spot.

• For masonry: Using the 7/16˝ (11.0 mm) masonry drill bit

drill a hole 2 1/2˝(64.0 mm) deep in each marked spot. Install

a masonry anchor in each hole.

5. Replace the safe in the desired position, with the holes in the

safe aligned with those in the floor.

6. Securing the safe:

• For wood: Pass each lag screw through a washer (rubber side

toward floor), then through the safe and into a hole. Tighten

with the wrench. (Fig. C)

• For masonry: Pass each lag screw though a washer (rubber

side toward floor), then through the safe and into a masonry

anchor. Tighten with the wrench. (Fig. D)

C D

A B

For safes with a

fingerprint swipe lock

IMPORTANT

For some fingerprint locks

NOTE: If you are experiencing difficulty with the

operation of the locking mechanism, DO NOT

RETURN THIS PRODUCT TO THE STORE. PLEASE

CONTACT SENTRY GROUP CUSTOMER SERVICE

at 1-800-828-1438 for assistance. Most problems

can be quickly resolved over the telephone.

It is important that you keep this Owner’s Manual in a secure

place other than IN your safe; it is your reference for the

safe’s Serial Number and Factory Code.

To open your safe for the first time

Battery installation:

To power the lock, four alkaline AA batteries, equalling voltage:

6Vdc (not included), are required.

NOTE: Non-alkaline and rechargeable batteries

ARE NOT RECOMMENDED.

To install batteries:

1. Remove and discard the screw at the base of the lock case.

2. Turn the electric lock case to the right (clockwise) from

12 o’clock to 2 o’clock and remove. Insert four new batteries

as indicated, replace the electric lock case and turn to the left

to reassemble.

Low battery notice

When the battery power gets low, the battery icon will blink with

each activation of the lock until batteries are replaced.

NOTE: No codes are erased when old batteries are

removed for replacement.

First time use

Open unit first, then test

with door open!

To unlock safe with numeric codes:

NOTE: Press CLEAR to remove numeric inputs.

Enter the 5-digit factory code provided on the front of the

Owner’s Manual, a pre-programmed manager code, or a pre-

programmed user code and press the key. PROG/ENTER (See

the following instructions for inputting manager and user

codes.) An asterisk will light each time a digit is entered. When

the unlocked padlock icon appears you have 4 seconds to turn

the handle downward and open the safe.

To unlock safe with a fingerprint:

Press any key except the key to wake the PROG/ENTER

electronic lock. Swipe your pre-programmed finger over the

sensor. When the unlocked padlock icon appears you have

4 seconds to turn the handle downward and open the safe.

To lock safe:

Close the door and return the handle to the horizontal position.

Tips for fingerprint

programming and usage

Best finger for programming

• Do not choose a finger with a cut or scar.

• Choose a finger with the tightest swirl pattern.

Swiping fingerprints

• When swiping, keep your finger flat against the

fingerprint sensor.

• Swipe in a downward motion using a consistent medium speed.

• Use a medium pressure on the sensor. Too firm or too light

will not read correctly.

• Also note where you are standing in relation to the safe.

Programming or usage at a different angle will not work well.

Skin condition

• If you have dirt on your hands, please wash them before using

the safe.

• Very dry skin will not program well. Use a skin moisturizer,

being sure to rub the moisturizer in well and remove any

excess before using the safe.

Environmental conditions

• The electronics may not work or may have a slow reaction time

in cold temperatures (50°F or less). Make sure that the safe is

at room temperature before programming and usage.

Cleaning the sensor

• For optimal accuracy and fingerprint-reading success, clean

the electronic case and fingerprint sensor periodically with a

dry, lint-free cloth.

Programming the manager code

NOTE: See page 2 for icon identification.

NOTE: All zeros is an invalid code. The pre-programmed

factory code is also an invalid manager code.

One (1) manager code is allowed.

To add:

1. Press PROG/ENTER.

2. Enter the 5-digit factory code.

3. Press PROG/ENTER.

4. Enter your new manager code consisting of 4-8 digits, and

then press PROG/ENTER.

To delete:

WAR NING: A manager code must be programmed to

add or delete users

1. Press PROG/ENTER.

2. Enter the 5-digit factory code.

3. Press PROG/ENTER.

4. Enter 0, 0, 0, 0, PROG/ENTER then the key.

Enrolling manager fingerprints

NOTE: The fingerprint lock stores one (1) manager and

up to six (6) users. The manager and each user

are encouraged to program two fingers,

preferably one finger from each hand.

To add:

1. Press PROG/ENTER twice.

2. Enter the 5-digit factory code.

3. Press PROG/ENTER.

4. Swipe your first finger in a over the downward direction

fingerprint sensor. Three accurate reads of the fingerprint are

necessary for successful enrollment. After each successful

swipe a beep up will sound and an asterisk will light. An

unsuccessful swipe will result in an ERR signal and a low pitch

will sound.

5. The blinking finger icon indicates that the sensor is ready

to read a fingerprint swipe. After the sensor reads a finger

swipe, the finger icon stays lit while saving the fingerprint into

memory. Wait for the finger icon to blink before proceeding

with additional finger swipes.

To delete:

1. Press PROG/ENTER twice.

2. Enter the 5-digit factory code.

3. Press PROG/ENTER.

4. Press 0, 0, 0, 0, PROG/ENTER then the key.

Errors while enrolling fingerprints:

1. A single signal means that the sensor did not BEEP/ERROR

read the fingerprint.

2. A three signal means that the sensor read the BEEP/ERROR

fingerprint but data did not meet minimum requirements.

3. The electronic lock will automatically turn off after ten

consecutive errors.

Product specificaties

Merk:	SentrySafe
Categorie:	Kluis
Model:	TC8-331
Kleur van het product:	Zwart
Gewicht:	79000 g
Breedte:	551 mm
Diepte:	508 mm
Hoogte:	704 mm
Afmetingen binnenkant (B x D x H):	376 x 302 x 499 mm