Scosche FD134030 Handleiding

Scosche Niet gecategoriseerd FD134030

Lees hieronder de 📖 handleiding in het Nederlandse voor Scosche FD134030 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

FD134030

IN-DASH INSTALLATION KIT FOR

1996-99 FORD TAURUS

1996-99 MERCURY SABLE

WITH ROTARY CLIMATE CONTROLS

Minor modification may be

necessary on console model.

See shaded area.

NOTE: •All wire codes are viewed as looking at the front of the plug with the wires

exiting the rear.

•Use these wiring codes as a guide. Your vehicle might differ.

BLACK 16-PIN

9 = Open

10 = Momentary Defrost on

11 = Open

12 = Open

13 = Not Used

14 = Open

15 = Not Used

16 = Not Used

Not Used = Substitute

"Not for aftermarket use"

1 = Led Defrost On +12V

2 = Open

3 = Not Used

4 = Not Used

5 = Not Used

6 = Not Used

7 = Not Used

8 = Not Used

1 = Illumination

2 = Ground

3 = Battery +12V

4 = Open

5 = Open

6 = Ground

7 = Open

8 = Accessory +12V

GRAY PLUG 8-PIN

8 = RF+

9 = Open

10 = Power Antenna

11 = Open

12 = Ground

13 = Ground

14 = Battery +12V

BLACK 14- SPEAKER INPUT *

1 = LR-

2 = LR+

3 = RR-

4 = RR+

5 = LF-

6 = LF+

7 = RF-

*Located in trunk

1996-97 VEHICLES

1998-UP VEHICLES

POWER AND SPEAKER

1. = White/Pink = Not Used

2. = Blue/White = Not Used

3. = Black = Not Used

4. = Green/Violet = Defroster on Indicator

5. = Black/Pink = +12V Accessory

6. = Empty

7. = Light Green/Black = Not Used

8. = Empty

9. = Light Blue/Black = Not Used

10. = Black (Larger Gauge) = -12V Chassis Ground

11. = Brown/Light Green = Not Used

12. = Gray = Not Used

13. = Empty

14. = Blue/Orange = Defroster Switch Wire

(Momentary Ground)

15. = Red/Yellow = Not Used

16. = Gray/Red = Not used

17. = Tan = Not Used

18. = Light Blue/Pink = Not Used

19. = Black/Light Green = Not Used

20. = White = +12V Constant

1 2 3 4 5 6 7 8

9 10 11 12 13 14

1 2 3

4 5 6 7 8

201918171615

1413

1211

1 1098765

FACTORY WIRING CODES

Thank you for purchasing the Scosche FD134030 installation panel. The FD134030 replaces

the factory radio/integrated control panel, while maintaining the original Rotary Climate

Controls and hardware. The factory radio dash panel is a control unit only, the amplifier and

tuner sections of the radio are remote located in left side of trunk on sedans, or left rear behind

the spare tire in wagons (see illustration "C"). The antenna cable is also located at the rear

module. The Scosche FD12 (18ft. speaker connector extension), FDA-18 (antenna extension),

and FD22 (FD10 to FD20 adapter) are included for aftermarket radio installations.

CAUTION: Disconnect your vehicle's negative battery terminal before the installa-

tion to help prevent electrical damage. We recommend the use of a volt/ohm meter

over a test light to check wiring. A test light or grounded wire probe can cause

damage to the vehicle's computer and/or diagnostic systems. Avoid all factory air

bag wiring - air bags can accidentally deploy causing serious injury or death.

INTRODUCTION

1. Insert DIN removal tools to release factory stereo/climate control panel. Unplug all

electrical connectors and vacuum lines, remove panel.

CLIMATE CONTROL KNOB HOUSING

REMOVAL:

1. Align the control knobs to vertical

position, then carefully pull off three

rotary control knobs from the face of

the factory radio/control panel.

2. From the back side of the factory

control panel, extract one (1) 5mm

screw from the FAN switch, twist out

(counter clockwise) to remove.

Repeat this procedure (clockwise) for

the TEMPERATURE switch.

3. From the back side of the factory

control panel, loosen the three (3) torx

head panel retention screws located next to the

switches removed. Carefully release the tape covering the bottom edge of the control

panel (the tape will be refitted). Carefully separate bottom of panel about 1/4". Use a

small screwdriver to release vacuum control retention clips.

4. Reattach all switches to the back side of the Scosche FD134030 installation panel in the

corresponding slots using the factory screws.

5. Reattach rotary control knobs.

MOUNTING CLIPS

1. Extract one (1) T-15 torx screw holding the factory mounting clip from each side. Remove

clips and reattach to the Scosche FD134030 using the factory screws.

1. Use the supplied connectors constant, ignition, dimmer, and ground wires for Aftermarket

radio installation.

2. Connect the new radio’s speaker outputs to the bare wire ends of the FD12 18 ft. speaker

extension harness.

3. Connect the new radio’s antenna lead to the standard male end of the 18 ft. antenna

extension cable.

4. Run extension cables to the rear of the vehicle to connect at the tuner/amp unit.

FD134030 KIT PREPARATION

FACTORY STEREO REMOVAL

AFTERMARKET RADIO WIRING CONNECTION

1. DIN front load installation. See Illustration "A".

2. DIN ISO installation.

• Attach ISO mount brackets (left and right) to the slots on kit opening, and secure radio

chassis to brackets using hardware supplied with radio. See Illustration "B".

• Snap iso trim ring to kit opening.

3. Scosche recommends rear support on all installations, by attaching the support strap,

(supplied with the radio), to the kit top support mount. See Illustrations.

*Bend strap as illustrated for maximum mounting depth.

TUNER/AMP

MODULE

FACTORY

FORD

ANTENNA

LEAD

TUNER/

AMP

OUTPUT

PLUG

ICP

CONTROL

HARNESS

1996-1997 MODELS

The FD134030 installation kit comes

prepared for 1996-1997 Ford Taurus/

Mercury Sable applications. Connect both

the 8 pin Radio power harness and the 16

pin defroster harness into the factory plugs.

1998-1999 MODELS

Use the supplied FD22 harness to adapt

the FD134030 for 1998-1999 models.

Connect the 8 pin power plug from the

FD22 with the corresponding plug on the kit

panel. Connect the 16 pin defroster

harness with the corresponding plug on the

kit panel. See picture to the right.

ILLUSTRATION "C"

DIN RADIO

INSTALLATION

DIN RADIO

TRIM PLATE

REAR SUPPORT

RADIO MOUNT

SLEEVE

ILLUSTRATION "A"

DIN RADIO

INSTALLATION

ILLUSTRATION "B"

DIN ISO MOUNT

INSTALLATION * REAR SUPPORT

ISO MOUNT

BRACKET

CAUTION:

REAR SUPPORTING THE

RADIO ADDS TO THE

INSTALLATION’S

STRUCTURAL INTEGRITY.

1996-97 1998-99

KIT INSTALLATION:

STEREO INSTALLATION:

SCOSCHE STEREO INSTALLATION COMPONENTS STEREO DASH KIT

Product specificaties

Merk:	Scosche
Categorie:	Niet gecategoriseerd
Model:	FD134030

Heb je hulp nodig?

Als je hulp nodig hebt met Scosche FD134030 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Scosche

Scosche ITCFD05AB Handleiding

9 Juli 2023

Scosche FT4275B Handleiding

9 Juli 2023

Scosche PSM21000 Handleiding

8 Juli 2023

Scosche SU2029B Handleiding

8 Juli 2023

Scosche IPD2CFBK Handleiding

7 Juli 2023

Scosche EFX PA10BX Handleiding

7 Juli 2023

Scosche SI-2227B Handleiding

7 Juli 2023

Scosche PBJ300 Handleiding

7 Juli 2023

Scosche EFX PA4BX Handleiding

6 Juli 2023

Scosche ITCLS01B Handleiding

6 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx 03863 Handleiding

24 December 2024

Vello PGS-P Handleiding

24 December 2024

Venom Quad Charging Station VS4796 Handleiding

24 December 2024

Nec IPJ2000CM Handleiding

24 December 2024

Monogram ZKPN Handleiding

24 December 2024

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024