Russound A-H484 Handleiding

Russound Hifi systeem A-H484

Lees hieronder de 📖 handleiding in het Nederlandse voor Russound A-H484 (2 pagina's) in de categorie Hifi systeem. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Model A-H484

Multi-Source, Multi-Zone Hub

for A-BUS System

Instruction Manual

INSTRUCTIONS FOR CONNECTING AND USING RUSSOUND MODEL A-H484. REFER TO THE DIAGRAMS INSIDE. A-H484 OVERVIEW

The A-H484 is an A-BUS 4-zone, 8-room, 4-source Audio

Distribution Hub. Used with IR-repeating Amplified Modules (e.g.,

A-KP2) and the A-LRC-1 remote, the A-H484 allows each of 4 zones

to independently select any of 4 sources. Each of the 4 zones can

support 2 Modules, making it possible to create an 8-room system.

IMPORTANT – Before installation, review the manuals included

with each component in your system. If you are unsure of any of

the installation procedures described herein or elsewhere, consult a

professional electronics installer.

A-H484 KEY FEATURES

1) Four line-level audio inputs

2) 4 Routed IR outputs (1 for each source); 1 Common IR output

3) 12-volt trigger output

4) Link In and Out

5) 4-zone coupled outputs (for 2 keypads per zone)

6) Dual power supply inputs (use 1 A-PS per 4 Amplified Modules)

7) IR remote controlled

8) Compact size for mounting near audio equipment

Connect up to 4 audio sources, such as a CD/DVD player or DSS

receiver. If the sources are connected to an existing home theater sys-

tem, you can share them with the A-484 by splitting their audio out-

puts with “Y” connectors (see diagram).

Using the optional A-LRC-1 IR remote control aimed at an A-KP2

keypad, press the ON button to turn on the keypad and the A-H484.

Select the source that you would like to listen to using the 1 through

4 SOURCE SELECT buttons. Use the VOL rocker to adjust the volume,

the OFF button to turn off the zone, and the ALL OFF button to turn

off all zones as well as the A-H484. Turning on a keypad manually

from any zone does not turn on the A-H484; that must be done from

the remote.

Mount the A-H484 near the source equipment using screws or hook

and loop fastener.

The Link In and Out is used to connect multiple A-H484 Hubs

together, which allows for use of additional Amplified Modules. The

Link connects the Routed IR, Common IR, and status, but you must

split the outputs of your source equipment to share the audio sig-

nals among multiple A-H484s. Use an RJ45 CAT-5 patch cable.

Routed IR Outputs and Common IR Output. When a source is

selected from a zone, the IR signal received through the zone’s

Module is routed exclusively to that source via the A-H484’s

Routed IR outputs. This allows the use of multiple sources of the

same brand (for example, two identical DSS units). The Common IR

output sends out all IR signals and can be used with an IR flasher

that blankets all source components. (Model 845.1 emitters shown

are not included.)

12-Volt Trigger Output. The trigger output can be used to control

a switched AC outlet, such as the Russound ACT-1, to turn power

on and off to source equipment. The trigger voltage is sent when

any zone in the system is turned on. When the ALL OFF command

is used, the trigger is turned off. Use a 1/8" male 2-conductor jack

(i.e., mini phono jack), not included.

5SOURCES

The A-H484 Hub and Amplified Modules are powered by the A-PS 24

VDC/4A power supply. Connect 1 Russound A-PS power supply to the

A-H484 for each row (A and B) of 4 Amplified Modules. The A-PS

should be plugged into an unswitched AC outlet (one that is live all

the time). When the A-PS is providing power, the A-H484’s SYSTEM

ON LED will illuminate.

6POWER SUPPLY

2IR EMITTERS

3TRIGGER OUTPUT

4LINK IN & LINK OUT

7OPERATION

8MOUNTING

A-BUS SYSTEM OVERVIEW

The product you have just purchased is an integral part of the Russound A-BUS

Multi-Room Audio System. It is a component which, when combined with

other essential components and your source equipment (receiver, CD player,

etc.), creates a versatile whole-house audio system that will fill your rooms with

high-quality sound for years to come.

A-BUS technology is a new, innovative method of providing high quality audio

to remote locations with a single 8-conductor cable such as CAT-5. A-BUS

technology provides many advantages over other methods of audio distribu-

tion, including: simple, single CAT-5 wiring scheme; infrared control of system

components; infrared control of the optional A-KP2 amplified keypad module;

and system power status.

Every A-BUS System is comprised of components from each of the following

three areas.

1. A-BUS Amplified Modules: The Module contains both the amplifier for the

room’s speakers as well as the control for those speakers. One Module

should be used for each room you choose to control. The Russound A-KP2

Amplified Keypad (with built-in IR receiver) and A-VC2 Amplified Volume

Control are examples of A-BUS Amplified Modules.

2. A-BUS Hubs: All components of the A-BUS system must be wired centrally

to a Hub located near your source equipment. The Hub provides the con-

nection for source equipment, volume controls, infrared emitters and power

supply. The A-H484, A-H4, A-H4D, and A-H2 are examples of A-BUS Hubs.

The A-H484, A-H4, and A-H2 are surface-mount units. The A-H4D is an in-

wall Decora© style unit.

3. Power Supply: The power supply plugs into the Hub. The Russound A-PS

24VDC/4A unit is an example.

A-H484 SPECIFICATIONS

Power Supply: A-PS. 24VDC/4A. One for each bank A and B.

Trigger Output: 12VDC/100mA. 1/8" Male. Tip (+), sleeve (–)

Keypad Connection: RJ-45 T568A Standard

Link Connection: RJ-45 T568A Standard

Emitter Connections: 1/8" Male. Tip (+), sleeve (–)

Dimensions: 6.5"W x 5"H x 1.5"D (165x127x38mm)

Weight: 1lb. 12oz. (795g)

LIMITED WARRANTY

The Russound A-H484 is fully guaranteed for Two (2) years from the date of purchase against

all defects in materials and workmanship. During this period Russound will replace any defec-

tive parts and correct any defect in workmanship without charge for either parts or labor.

For this warranty to apply, the unit must be installed and used according to its written

instructions. If service is necessary, it must be performed by Russound. The unit must be

returned to Russound at the owner’s expense and with prior written permission. Accidental

damage and shipping damage are not considered defects under the terms of the warranty.

Russound assumes no responsibility for defects resulting from abuse or servicing performed

by an agency or person not specifically authorized in writing by Russound. Damage to or

destruction of components due to improper use voids the warranty. In these cases the repair

will be made at the owner’s expense. To return for repairs, the unit must be shipped to

Russound at the owner’s expense, along with a note explaining the nature of the service

required. Be sure to pack in a corrugated container with at least 3 inches of resilient mate-

rial to protect the unit from damage in transit.

5 Forbes Rd. Newmarket, NH 03857, USA

☎ 603.659.5170 • Fax 603.659.5388

e-mail: tech@russound.com

Come visit us at:

English

Coupled Zone Outputs. Each of the 4 zone outputs can support 2

Amplified Modules connected via CAT-5 cable. For example, in

Zone 1 you might use an A-KP2 keypad (connector 1A) in the main

room and an A-VC2 volume control (connector 1B) in a secondary

area where IR control is not needed.

A CAT-5 cable is used to connect each A-KP2 or A-VC2 Amplified

Module to a keypad output on the A-H484 Hub. For clean installa-

tions, use RJ45 CAT-5 patch cables to connect from the Hub to an

RJ45 Wall Plate (optional), and then wire from the Wall Plate to

the Amplified Module (see diagram). The Amplified Modules have

110 punchdown connectors for the 8 individual conductors of the

CAT-5 cable (use a punchdown tool with a 110 blade to insert con-

ductors).

NOTE: When wiring directly to an Amplified Module (i.e., not using

an RJ45 Wall Plate) use T568A RJ45 wire configuration.

1AMPLIFIED MODULES

LINK

OUTIN

LINK

OUTIN

S #ERIAL

DESIGNED IN USA MADE IN KOREA

4321

SOURCE IR

COMMON IR

UTPUT

EYPADS

UTPUT

A K

EYPADS

RIGGER

VDC

100mA

YSTEM

A/B C -ZOUPLED ONE OUTPUT

SOURCE A IUDIO NPUT

EWMARKET, NH U.S.A.

A-H484

OWER

A K

EYPADS

OWER

B K

EYPADS

+24V

1A2A4A

1B2B4B

LINK

OUTIN

4 C -Z , 4-SOUPLED ONE OURCE

P MANEL OUNT UDIO A HUB

DVD

DSS

DVD

DSS

Pos (+)

Neg (–)

ACT-1

TUNER (or tuner in receiver)

1 2 3 4 5 6 7 8

CAT-5

(behind wall)

CONNECTION DIAGRAMS FOR RUSSOUND MODEL A-H484. REFER TO THE INSTRUCTIONS ON BACK. DIAGRAMS ARE NOT TO SCALE.

A-H484

Power Strip AC

A-PS (or A-PS4)

1 A-PS (or A-PS4) required for each row of keypads

A-KP2 Amplified Module

A-LRC-1 IR Remote (optional)

Emitter attaches

to each source

component’s

IR window

“Y” connectors allow each source

to be shared with receiver

Audio Receiver

A-H484 A-H484

Source

Components

110 punchdown connectors on Amplified Module

RJ45 Wall Plate

(optional)

located

near Hub

RJ45 CAT-5 patch cables

When wiring directly to Amplified Module,

use T568A RJ45 wire configuration

Wire order

BROWN

GREEN

ORANGE

BLUE

GREEN

ORANGE

BLUE

ORANGE

BROWN

Product specificaties

Merk:	Russound
Categorie:	Hifi systeem
Model:	A-H484
Gewicht:	795 g
Breedte:	165 mm
Diepte:	38 mm
Hoogte:	127 mm
Gewicht verpakking:	1000 g
Breedte verpakking:	220 mm
Diepte verpakking:	178 mm
Hoogte verpakking:	70 mm
Montagewijze:	Plank-/wandgemonteerd
Certificering:	CE, FCC, TUV
Audio-ingangen:	RCA
12V trigger:	Ja
Aantal audiobroningangen:	4
Aantal zones:	4
IR-zenderaansluitingen:	5
Zenderconnectors:	1/8" (3.5 mm) TS
Type uitvoer toetsenbord:	RJ-45
Linkconnectors:	RJ-45
Aantal uitvoeren toetsenbord:	8