Rosieres RHT619/2IN Handleiding

Rosieres Afzuigkap RHT619/2IN

Lees hieronder de 📖 handleiding in het Nederlandse voor Rosieres RHT619/2IN (20 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/20

INSTRUCTIONS FOR INSTALLATION AND USE

MONTAGE- UND GEBRAUCHSANWEISUNG

INSTRUCTIONS POUR L'INSTALLATION ET L’UTILISATION

ISTRUZIONI PER L'INSTALLAZIONE E L’USO

INSTRUCCIONES PARA INSTALACIÓN Y USO

INSTRUÇÕES DE INSTALAÇÃO Y UTILIZAÇÃO

AANWIJZING VOOR GEBRUIK EN INSTALLATIE

RHT619/1

ENGLISH

DESCRIPTION

The appliance can be used in both the filtering and ducting version.

In the Filtering version (Fig. 1), the air and vapours conveyed by the appliance are depurated by charcoal filters and

recirculated around the room. ATTENTION: When using the filtering version, charcoal filters must be installed (the charcoal

filters are not supplied). In the Ducting version (Fig. 2), cooking vapours and odours are conveyed straight outside by

a disposal duct which passes through the wall. Use of charcoal filters is therefore unnecessary.

If your appliance is made of stainless steel, it might be covered with a protective film: remove it before

installation.

INSTALLATION

Before assembling, in order to manoeuvre the appliance more easily, take off the grease grille (Fig. 3): pull the front

of the grille upwards; desinsert the back from its seat.

IMPORTANT: So as not to damage your product, during installation USE ONLY THE SCREWS PROVIDED. Make sure

these are used as shown in the following instructions.

To compensate possible depth voids between the appliance and the wall, a plastic SPACING BAR to be fixed at the

back of the appliance by means of the three screws A is included (Fig. 4). The 3 screws A to be used are contained

in the accessory bag attached to the plastic spacing bar. Cut the spacing bar according to the distance to be adjusted.

ASSEMBLY UNDER A PENSILE CUPBOARD

The following operations are essential for assembly:

– Install the wiring system

– Prepare the air venting hole if your applian-ce is to be installed in the Ducting version.

Fixation as indicated in Fig. 5:

Make the 4 necessary fixing holes in the bottom of the cupboard and cut the air venting hole. Move the hood

close to the bottom of the wall unit and then connect the two units by means of the 4 self-tapping screws supplied

together with the appliance.

Fixation with brackets as in Fig. 6:

Take the two brackets (S) out of the accessory bag together with the 4 screws provided. Fit the brackets to the

wall unit being careful to position these correctly; for this operation use the 4 longer screws. At this point,

adjust the angle of the appliance with the 4 screws (B) and fasten the appliance to the brackets using the

2 shorter screws (C).

Ducting version : connect the flange of the hood with the air venting hole made previously in the wall/ceiling by means

of an adequate tube. Make the electrical connections. Assemble the anti-grease grille with the hood, inserting it obliquely

(making the front side go upwards).

Filtering version : connect an adequate pipe to the connecting flange of the appliance so that it conveys the air up to

the top of the pensile cupboard (pipe is not provided). Make the electrical connections.

HOW TO TAKE OFF THE GLASS

Before any cleaning or any servicing it is necessary to disconnect the apparatus. To take off the glass, open the trolley

pulling it frontwards; pull the glass towards the left (or the right) and lift one side upwards as it is indicated in the

Figure 13.

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls (Fig. 7):

MOTOR - Switch A

When set on position "1" the motor will be switched on and off automatically by opening and closing the telescopic visor.

When set on position "0" the motor will remain off at all times.

SPEED - Switch B

Allows the operating speed of the motor to be regulated by means of an electronic speed variator.

LIGHT - Switch C

When light switch is on "AUT" position the light will be turned on and off automatically by opening and closing the visor.

When set to "0" position, the light will remain off, regardless of position of visor.

On "MAN" position the light will be switched on regardless of position of visor.

Controls (Fig. 8):

Button A: turns the lights on/off; every 30 hours of operation the corresponding pilot lamp (S) illuminates to indicate

that the grease filters must be cleaned; every 120 hours of operation the corresponding pilot lamp (S) flashes to indicate

that the grease filters must be cleaned and the charcoal filter replaced. To restart the hour counter (RESET), hold the

button A pressed down for about 1” (while the pilot lamp S is on). Button B: drives the motor in first speed (the corresponding

pilot lamp comes on); when holding it down for about 1”, the motor cuts out. Button C: drives the motor in second speed

Product specificaties

Merk:	Rosieres
Categorie:	Afzuigkap
Model:	RHT619/2IN
Soort bediening:	Knoppen
Kleur van het product:	Zilver
Breedte:	- mm
Hoogte:	- mm
Geluidsniveau:	68 dB
Soort:	Onderbouw
Motor vermogen:	250 W
Uitlaat aansluiting diameter:	123 mm
Aantal motors:	1
Materiaal behuizing:	Roestvrijstaal
Maximale afzuigcapaciteit:	770 m³/uur
Aantal lampen:	2 gloeilamp(en)
Type lamp:	Halogeen
Soort vetfilter:	Metaal
Vermogen lamp:	20 W
Aantal filters:	2 stuk(s)
Aantal snelheden:	4
Vaatwasserbestendig filter:	Ja
Ingebouwde functie:	Ja