Quoizel PCGN1616C Handleiding

Quoizel Verlichting PCGN1616C

Lees hieronder de 📖 handleiding in het Nederlandse voor Quoizel PCGN1616C (2 pagina's) in de categorie Verlichting. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Package Contents
Please go to for product cleaning tips. Go to the selection.
(5) G9 Base Clear G9 Xenon Bulbs 40W Maximum (supplied).
www.quoizel.com Care + Maintenance
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source:
Estimated Assembly Time:
Preparation:
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-PCGN1616C
For Style PCGN1616C
2017 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Do not touch the bulb with bare hands use a cloth or glove.
BFixture Body
x 1
Crossbar Assembly
x 1
AC
Clear G9
Xenon Bulb
x 5
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-04-01
DCrystal Strings
Crystal
String B
x 8 Crystal
String C
x 24
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires with ground wire through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to Outlet Box with
the head of Green Ground Screw facing you. Secure it with Outlet
Box Screws (not included). Tighten until snug.
STEP 2 - Test Fit the Ceiling Canopy to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the ceiling canopy and the Fixture Body (B) onto the Crossbar
Assembly (A) and secure with mounting balls. Note: The ceiling
canopy and the Fixture Body (B) should be snug against the ceiling
and held tight with the mounting balls. If it is not, adjust the length of
the mounting screws on the Crossbar Assembly (A) by unscrewing
Crystal
String A
x 3
(Step 2 Continued)
the preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Fixture Body (B) is secure, remove the
mounting ball and Fixture Body (B) and proceed to Step 3.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Bare, or Green
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
Figure 3
Supply Wires
with Ground WireOutlet Box Screws
(not included)
Outlet Box
A
Figure 1
Mounting
Screw
Hex Nut and
Lock Washer
Mounting
Ball
A
B
Figure 2
Ceiling
Canopy
2of2
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-04-17
CAUTION FOR BULB REPLACING
A. When replace bulb, turn off power and allow lamp to cool. For safety
purpose, wear gloves and eye protection.
B. If bulb is scratched or cracked, DO NOT use the lamp to avoid
breakage during use or installation.
C. Use only in fixtures rated for lamps wattage and voltage.
D. Prevent the bulb from contacting liquid or combustible materials.
STEP 4 Install the Fixture-
A. Remove Protective Film from Ceiling Canopy. Position the ceiling
canopy and Fixture Body (B) onto the Crossbar Assembly (A). Place
the holes in the ceiling canopy over the mounting screws. Secure
the Fixture Body (B) by using the mounting balls and hand tighten
the mounting balls until snug.
STEP 5 Install Bulbs and Crystal Strings
IMPORTANT:
-
A. Insert bulbs (C) into sockets and push snugly into place.
Do not touch the bulb with bare hands use a cloth or
glove.
(Refer to CRYSTAL STRINGS DISTRIBUTION)
B. Attach Crystal Strings A to locations A on the Fixture Body (B) first.
And then attach Crystal Strings B to locations “B” on the Fixture
Body (B).
C. Attach the beads end of the Crystal Strings C to inner locations C
on the Fixture Body (B) first. And then attach the crystal end of the
Crystal String C to outer locations C” on the Fixture Body (B).
Your fixture is now assembled and ready to use. Enjoy!
Crystal
String A
Crystal
String B
Crystal
String C
C
Socket
CRYSTAL STRINGS DISTRIBUTIONS
A
A
A
BBB
B
B
B
B
B
CCCCC
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
CCCC
CCCC
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Figure 5
PCGN1616C
FINISH: POLISHED CHROME
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
15.75” Dia.
13.75” Dia.
8.75”
Figure 4
Mounting
Screw
Mounting Ball
A
B
Ceiling
Canopy
Protective Film


Product specificaties

Merk: Quoizel
Categorie: Verlichting
Model: PCGN1616C

Heb je hulp nodig?

Als je hulp nodig hebt met Quoizel PCGN1616C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Verlichting Quoizel

Handleiding Verlichting

Nieuwste handleidingen voor Verlichting