Quoizel BRX1614C Handleiding

Quoizel Verlichting BRX1614C

Lees hieronder de 📖 handleiding in het Nederlandse voor Quoizel BRX1614C (2 pagina's) in de categorie Verlichting. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Package Contents
Please go to for product cleaning tips. Go to the selection.
(4) G9 Xenon Clear Bulbs (supplied),40W Maximum
www.quoizel.com Care + Maintenance
Light Source:
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Estimated Assembly Time:
Preparation:
30-45 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
1of2
Assembly Instruction Sheet #IS-BRX1614C
For Style BRX1614C
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Warnings and Cautions
Crossbar Assembly
x 1
B
Fixture Body
x 1
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Do not touch the bulb with bare hands use a cloth or glove.
C
Wall Anchor
x 2
D
Self-tapping Screw
x 2
STEP 1 Attach Crossbar Assembly to Outlet Box-
A. Place the Crossbar Assembly (A) onto the Ceiling surface and line
up one set of holes onto mounting holes on Outlet Box. Using a
pencil, mark the locations for Wall Anchors (B).
B. Remove the Crossbar Assembly (A) and drill holes from the marks
and then push the Wall Anchors (B) into the holes.
Flat Washer
x 2
Mounting Ball
x 2
G9 Xenon Clear Bulb
x 4
Clear Crystal
L: 3-3/8"
x 14
Clear Crystal
L: 5"
x 6
Clear Crystal
L: 6-5/8"
x 1
E
F
G
H
I
J
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
STEP 3 - Attach Ceiling Canopy to Mounting Screw
A. Remove Protective Film from Ceiling Canopy.
Note: Gloves are required to avoid leaving fingerprints or scratches
on Ceiling Canopy.
B. Place the Ceiling Canopy on the Fixture Body (F) over the Mounting
Screws and secure with Mounting Balls (E). Hand tighten until snug.
A
STEP 4 - Install Bulb
IMPORTANT:
A. This fixture uses G9 Xenon Clear Bulbs (G). Maximum 40 watts.
Insert bulb and seat properly into place.
Do not touch the bulb with bare hands use a cloth or
glove.
Figure 4
Socket
G
C. Position the Crossbar
Assembly (A) back onto the
Ceiling. Thread the Outlet Box
Screws (not supplied) into the
mounting holes on the Outlet
Box to secure it. Hand tighten
until snug.
D. Pass Flat Washers (D) over
Self-tapping screws (C) and
then thread self-tapping
screws (C) into Wall Anchors
(B). Hand tighten until snug.
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
Protective Film
E
F
Mounting Screw
Figure 3
STEP 5 - Install Crystal to Fixture
A. (Refer to ) Attach the Clear Crystal L6-5/8 (J)Crystal Distribution
July2015
Figure 1
Ceiling
Outlet Box
Outlet Box Screw
(not included)
B
A
C
D
(Step 2 Continued)
connected wires into the Outlet Box.
4
3
2
2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc. July2015
BRX1614C
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
REPLACEMENT PART DESCRIPTION REQ.NO.
1
FINISH: POLISHED CHROME
(4)40W
(Supplied)
Maximum
G9 Xenon Clear
Bulbs
1
I1202SC G9 XENON CLEAR BULB 4
2
3
G12271SH
G12272SH
CLEAR CRYSTAL L:3-3/8"
CLEAR GLASS L5"
14
6
4G12273SH CLEAR GLASS L6-5/8" 1
F
H
I
J
A
C
Crystal Distribution
Figure 5
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
CAUTION FOR BULB REPLACING
A. When replace bulb, turn off power and allow lamp to cool. For safety purpose, wear gloves and eye protection.
B. If bulb is scratched or cracked, DO NOT use the lamp to avoid breakage during use or installation.
C. Use only in fixtures rated for lamps wattage and voltage.
D. Lamp operate under high pressure generating intense heat. Prevent contact with liquid and combustible materials.
(Step 5 Continued)
to the location C” on the Ceiling Canopy. Attach Clear
Crystal L5” (I) to the location “B on the Ceiling Canopy.
Attach Clear Crystal L3-3/8” (H) to the location A on the
Ceiling Canopy.
Your fixture is now assembled and ready to use. Enjoy!
13.75” Dia.
11.75” Dia.
7.75
A
C
Crystal Distribution
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
Clear Crystal
L: 3-3/8"
x 14
Clear Crystal
L: 5"
x 6
Clear Crystal
L: 6-5/8"
x 1


Product specificaties

Merk: Quoizel
Categorie: Verlichting
Model: BRX1614C

Heb je hulp nodig?

Als je hulp nodig hebt met Quoizel BRX1614C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Verlichting Quoizel

Handleiding Verlichting

Nieuwste handleidingen voor Verlichting