QSC AD-P.SUB Handleiding

QSC Subwoofer AD-P.SUB

Lees hieronder de 📖 handleiding in het Nederlandse voor QSC AD-P.SUB (6 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

Acoustic Design Series

Quick Start Guide

AD-P.SUB

AD-P.SAT

TD-001564-01

*TD-001564-01* 1

EXPLANATION OF SYMBOLS

The term “WARNING” indicates instructions regarding personal safety. Failure to follow them may result in bodily injury or death.

The term indicates instructions regarding possible damage to physical equipment. equipment damage “CAUTION” Failure to follow them may result in

to equipment that may not be covered under the warranty.

The term “IMPORTANT” indicates instructions or information that are vital to the successful completion of theprocedure.

The term indicates additional useful information.“NOTE”

The lightning ﬂash with arrowhead symbol in a triangle alerts the user to the presence of uninsulated dangerous voltage within the product’s

enclosure that may constitute a risk of electric shock to humans.

The exclamation point within a triangle alerts the user to important safety, operating, and maintenance instructions in this manual.

1. Read these instructions and keep a copy for future reference.

2. Strictly follow and heed all instructions and warnings.

3. Consult a licensed and qualiﬁed professional engineer to devise and/or review an appropriate pendant mounting scheme.

4. Do not use or submerge this loudspeaker product in or near water or liquids.

5. Clean only with a dry cloth. Do not use any aerosol spray, cleaner, disinfectant or fumigant on, near, or into the loudspeaker product.

6. Do not block any ventilation opening. Install in accordance with the manufacturer’s instructions.

7. Do not install the loudspeaker near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers).

8. Do not use any attachments, accessories, mounts, or brackets that are not speciﬁed or approved by QSC, LLC.

9. Refer all service to qualiﬁed personnel. Service is required if the hanging mechanism or loudspeaker have been damaged in any way, such as liquid

having been spilled or objects have fallen into the loudspeaker or the loudspeaker has been exposed to rain or moisture, does not operate normally,

or has been dropped.

10. Observe all applicable local codes.

11. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.

Maintenance and Repair

Advanced technology—e.g., the use of modern materials and powerful electronics—requires specially adapted maintenance and repair methods. To

avoid subsequent damage to the equipment, personal injury, and/or creation of additional safety hazards, have all maintenance or repair work on the

equipment performed only by a QSC authorized service station or an authorized QSC International Distributor. QSC is not responsible for any injury, harm,

or related damages that arise from any failure of the customer, owner, or user of the equipment to facilitate those repairs.

Warranty

For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com

IMPORTANT SAFETY INSTRUCTIONS

TD-001564-01 2

Suspend the Subwoofer

WARNING!: Do not attach the snap hook to

the loudspeaker or any other load until the

hanger cable has been anchored to a suitable

structural member.

1. Insert the wire cable into the appropriate hole in the slip-lock fastener

(see Figure 1). The fastener’s two holes are directional, so cable will

only insert one way; if it will not go through, the cable is inserted into

the wrong hole.

2. Loop the cable over the structural member where the subwoofer is

to hang. The structure must be capable of supporting at least 5× the

weight of the subwoofer—AD-P.SUB: 17.5 lb or 8 kg.

NOTE: Building codes in some jurisdictions

may require higher safety factors.

Note that the subwoofer uses two hanger cables.

3. Insert the cable through the other hole in the fastener.

4. Adjust the length of the cable hang so the snap hook is at the desired

height. To shorten the hang, simply pull the cable further through one

or both holes in the fastener (Figure 2). To lengthen the hang or to

remove the cable from the structural member, insert the release key

into the appropriate release key hole; this will unlock that hole in the

fastener and allow the cable to move in the other direction (Figure3).

WARNING!: Never insert the release key while

there is a load on the hanger cable.

5. Repeat for the other hanger cables.

6. Attach both snap hooks to the suspension tab on the subwoofer

(Figure 4). Make sure the safety latch on the hook closes fully with the

subwoofer attached before you transfer the weight of the subwoofer to

the cables.

Install the AD-P.SUB Subwoofer

What’s in the AD-P.SUB Box

— Figure 1 —

Insert cable

here

Release

key hole

End view

— Figure 2 — — Figure 3 —

Structural

member

Pull cable to

shorten hang.

Insert release

key to lengthen

hang or remove.

Insert cable

here

Release

key hole

End view

Structural

member

Structural

member

1×

AD-P.SUB

1×

Cover 1

1×

Cover 2

8×

Screw

2×

Hanger cable

with slip-lock

fastener

3×

Euro-style plug

1×

Magnetic

grille

1×

Warranty

1×

Quick Start

Guide

TD-001547

TD-001564-01 3

Wire the Subwoofer

We recommend using insulated twisted pair stranded copper wire of an

adequate gauge to minimize resistive losses. To facilitate connection,

the AD-P.SUB loudspeakers have a four-pole connector for the input and

two more for the high-pass outputs to as many as four 16Ω satellite

loudspeakers (Figure 5). Each subwoofer comes with three Euro-style four-

pole pluggable connectors with clamping screws for securing to the wire

conductors.

1. Remove the magnetic grille and set the transformer tap switch to the

desired power (in watts) or to 4Ω for low-impedance operation (Figure

6). Reattach the grille. This setting can always be readjusted in the

future as needed.

2. On the top of the enclosure, remove the two protective covers over

the input and output connectors. The smaller cover has one gland

(protective cable pass-through) and the larger one has two.

3. Route the wires coming from the ampliﬁer through the gland in the

smaller cover. Route the wires for the satellte loudspeakers through one

or both glands on the larger cover.

4. Strip the wire ends about 6 mm or about 1/4 inch.

5. Connect the pairs of wires to the + and - terminals of the Euro-style

connectors as shown in Figure 7. Tighten the clamping screws to hold

the wires securely.

To daisy-chain forward to another loudspeaker, route a second wire

pair through the gland and attach them to the THRU terminals of the

input Euro-style connector. Be mindful of polarity when connecting

multiple loudspeakers; always connect to and to .+ + – –

6. Plug the connectors into their respective locations and tighten their

retaining screws. Reinstall the protective covers and tighten the gland

nuts to secure the wires.

7. To strain-relieve the wires, secure them to a hanger cable using the

tie-wraps provided.

WARNING!: Install the system in accordance

with local building codes and regulations. Some

jurisdictions may require additional suspension

points.

Use a licensed contractor or professional

engineer. QSC is not responsible for damages

that result from negligent installation of any

bracket, hanger, or loudspeaker.

— Figure 4 —

100

4Ω

12.5

100

N/A

4Ω

Volts

100

Volt

— Figure 6 —

AD-P.SUB

ACOUST IC DESIGN

PENDANT SUBWO OFER

INPUT: 70V, 100V, Z (4Ω)LOW-

MAXIMUM POWER RAT ING: 100 W RMS/200 W PROGRAM

HI-PASS FILTERED (200Hz-20kHz )

OUT PUT S 16Ω TELL IT E SPEAKERSTO SA

SA SAT 1 T 2 SAT 3 T 4SA

— Figure 5 —

1 T

T 2 To SAT 3

(if needed)

To SAT 4

(if needed)

Amp

To other subwoofers

THRU

— Figure 7 —

Product specificaties

Merk:	QSC
Categorie:	Subwoofer
Model:	AD-P.SUB
Kleur van het product:	Wit
Gewicht:	7950 g
Breedte:	346 mm
Diepte:	359 mm
Hoogte:	- mm
Gewicht verpakking:	9890 g
Breedte verpakking:	435 mm
Diepte verpakking:	435 mm
Hoogte verpakking:	435 mm
Bluetooth:	Nee
Type verpakking:	Doos
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	100 W
Aanbevolen gebruik:	Universeel
Impedantie:	4 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Plafond-montage
Aantal drivers:	1
Diameter driver:	165 mm
Frequentiebereik:	55 - 15000 Hz
Gevoeligheid:	86 dB
Signaal/ruis-verhouding:	106 dB
Versterker:	Extern
Bedrijfstemperatuur (T-T):	-20 - 50 °C
Aanbevolen versterkingskracht (max):	100 W