Pyle PRJELMT86 Handleiding

Pyle Projectiescherm PRJELMT86

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Pyle PRJELMT86 (2 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
INSTALLATION AND USAGE OF ELECTRIC SCREEN:
When you need to hang projection
screen on the ceiling, you should
install two pieces of pothooks at
the corresponding position on the
ceiling rst, then latch on hanging
hook which is on the end cap of
projection screen.
CEILING MOUNT:
Press the button to raise the UP
screen and the button to DOWN
lower the screen for viewing. Press
STOP at any point to position the
screen anywhere in between its
highest and lowest position
* NOTE: Screen can be controlled by both wired and
wireless controllers
REMOTE USAGE:
WALL MOUNT:
There is a key ring on the bracket
at both ends of the screen, when
you need to hang projection
screen on the wall, you should
hammer down nails or install
screws at the corresponding
position on the wall rst, then
hang up the screen.
Carefully remove the screen after opening the box. Be careful
not to damage the surface of the screen or its housing during
this process.
According to projecting requirements, x up the wall shelf
securely. (Note that the two wall shelves must be at the same
height, otherwise screen surface will be slanted to one side)
Carefully hang the screen on the wall shelf.
Once installation is complete, a red light will show on the switch box
when the screen is powered on. Press the and switch on UP DOWN
the switch box to make sure the screen functions normally.
Use either the wired, or included wireless remote to control the
screen according to your preference.
1.
2.
3.
4.
5.
NAIL
WALL
SCREEN DIRECTION
SCREEN
HOUSING
SCREEN DIRECTION
SCREEN
HOUSING
CEILING
POTHOOK
HANGING
HOOK
SCREEN
HOUSING
WIRED
REMOTE
HANGING
HOOK
Models:
PRJELMT76
PRJELMT86
PRJELMT106
Motorized Projector Screen
w/ Remote Control
Specications
Troubleshooting
PRJELMT106PRJELMT86PRJELMT76MODEL
68.9’’ x 80.7’’60.2’’ x 68.9’’52.8’’ x 59.1’’
TOTAL SCREEN SIZE
100 in. Diagonal
(59.1’’ x 78.7’’)
84 in. Diagonal
(50.4’’ x 67.0’’)
72 in. Diagonal
(42.9’’ x 57.0’’)
VIEWING AREA
91.0’’79.1’’69.3’’
HOUSING WIDTH
Aspect Ratio: 4:3/HD
Viewing Area: 128cm *170cm
Screen Gain: 1.3, Triple layered
Surface: Matte white, washable
Borders: Standard 4 black masking borders
Casing Color: White
Operation: Wired controller, Wireless remote control
Power: 120V, AC
YELLOW HOLE:
Adjust the max retraction position if screen does
not stop where it should when being retracted into
the housing. Adjust clockwise and counterclockwise
until you reach your desired position.
GREY HOLE:
Adjust the if screen does not stop max drop position
where it should when being lowered for viewing.
Adjust clockwise and counterclockwise until you
reach your desired position.
FIXING THE MIN/MAX POSITION
Every screen is factory set to an adequate xed position before packaging, however
due to movement during transportation, this position may shift. This is entirely normal
and can easily be remiedied by adjusting the two holes as detailed below:


Product specificaties

Merk: Pyle
Categorie: Projectiescherm
Model: PRJELMT86

Heb je hulp nodig?

Als je hulp nodig hebt met Pyle PRJELMT86 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Projectiescherm Pyle

Handleiding Projectiescherm

Nieuwste handleidingen voor Projectiescherm