Pyle PLVW1342R Handleiding

Pyle Monitor PLVW1342R

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PLVW1342R (3 pagina's) in de categorie Monitor. Deze handleiding was nuttig voor 71 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

PLVW1342

WARNING:

HAZARD DO NOT OPERATE THIS

UNIT UNLESS VEHICLE IS PARKED

IN SAFE AND LEGAL AREA

Screen Size: 13 inch 4:3TFT

System: PAL/NTSC

Display Method: TFT Active matrix system

Power source/Consumption: DC12V+/-20%, 15W

Storage Temperature: -10 ~ +85

Display Method : Color LCD

Monitor dimension: 325x275x30mm

Pixs: 800x600

Weight: 900g

Cautions

Never connect the car adaptor to cigarette lighters for such as trucks

or buses which use 12V DC power.

Do not expose the monitor to high humidity, dust, steam,oily smoke,

direct sunlight etc.

For your safety, turn power OFF when not in use and unplug the adaptor.

Never attempt your own maintenance. Consult your TV dealer or the

company.

Avoid dropping and strong impact.

For your safety, the driver should not watch the Monitor or operate the

controls while driving.

Accessories

1xRemote control 1xinstruction manual

WARNING:

DO NOT WATCH MONITOR WHILE VEHICLE IN MOTION.

IT CAN BE HAZARDOUS.

Specifications

13 TFT LCD COLOR MONITOR

Instruction Manual

PREAUTIONS

The set is for use in DC12V ,negaive ground vehicles.

Do not operate the set in ways other than described in this guide .Doing

so may damage it and may void your warranty.

SAFETY FIRST FOR REAR SEAT USE ONLY .Do not install on dashboard

or any where else that would permit monitor to be viewed by the driver .

Monitor must never be used in any manner that will distract driver or

interfere with the drivers

safe operation of the monitor vehivle.

Be careful not to run down the car battery while using the set with the

car stopped.Do not disassemble or modify the set .Doing so may damage

it and voids your warranty.

Keep drinks and drops from numberllas away from the set .Water may

damage the internal circuitry.

Do not let the set become hot .If temperature in the car is high or the

set has been exposed to direct sunlight and is hot ,lower the temperature

before using it .In extremely cold temperature ,the movement of the

picture may be slow and the picture may be dark ,but this is not a

malfunction .The set will work normally once the temperature increases.

Thank you for the purchase of this roof mounting 13inch TFT-LCD

monitor .Before operating the unit ,please read this manual

thoroughly and keep it for future reference.

REMOTE CONTROL BATTERY

1.Always use new batteries when replacing the old set .

2. Do not attempt to charge ,short-circuit ,disassemble ,heat or burn

used batteries.

3.Battery replacement is necessary when remote control acts

sporadically or stops operating this device.

4.Do not place objects between the remote control and remote receiver.

5.If the monitor does not operate even when operating the remote

control from a colse rangre ,it is time to replace the batteries

Product number :(cr2025)

INSTALLATION

The device is an overhead ,fold-down 13 inch monitor with an infrared

ir eye .It will accept a video signal from any video source with composite

videout .

1.Look over the vehicle for a location for the monitor .Each vehicle

is different and locations will vary .Make sure the monitor will not

interfere with the driver.

2.Once a location has been determined ,connect the IR ,A/V RCAs

and Powercables to the designated sources.

3.Feed the cables through the hole in the mounting bracket and

screw the bracket to the head liner ,Use short screws so as not to

damage the roof.

4.Plug the cable into the monitors 6 pin din connector .Mount the

monitor with the provided hardware.

Back of the remote

Battery tank

Battery

Transparent slice

Pannel

1.LED 2.Power

3.AV1 4.AV2

5.+ 6.MENU

7.- 8.RSI

9.IR 10.Dome light

11.Monitor release button 12.Dome light switch

REMOTE CONTROL

1.Power ON/OFF the monitor

2.Contrast positive adjustment

3.Switch between V1 and V2

4.Brightness positive adjustment

5.Brightness negative adjustment

6.Contrast negative adjustment

7.Saturation negative adjustment

8.Saturation positive adjustment

TFT-LCD

MONITOR REMOTE

WIRING DIAGRAM

Read all wiring precautions .If you are not sure of the connections ,contact your

authorized dealer.

1.Disconnect the negative(-) lead of the battery before making any power

connections.

2.When creating passage holes for the power wires ,use grommets to eliminate

any sharp edges created during drilling .This will protect the wire from being

nicked and causing a short circuit .

3.When connecting the ground lead ,fasten the ground lead(black) securely to a

clean metal plate on the vehicle .

Video1 input (yellow RCA)

FUSE 2A

12V

BATTERY

PLAYER

Video input2 (white RCA)

Red

Black

Product specificaties

Merk:	Pyle
Categorie:	Monitor
Model:	PLVW1342R
Kleur van het product:	Zwart
Gewicht:	3343 g
Breedte:	342.9 mm
Diepte:	292.1 mm
Hoogte:	30.5 mm
LED-indicatoren:	Ja
Beeldschermdiagonaal:	13.4 "
Resolutie:	800 x 600 Pixels
Touchscreen:	Nee
Oorspronkelijke beeldverhouding:	4:3
Montagewijze:	Dak
Geïntegreerde geheugenkaartlezer:	Nee
Formaat analoog signaal:	NTSC, PAL
Geïntegreerde TV Tuner:	Ja
On Screen Display (OSD):	Ja
Ingebouwd licht:	Ja
Draaibaar:	Ja
Horizontaal draaibaar:	-45 - 45 °
Op afstand bedienbaar:	Ja
Afstandsbediening inbegrepen:	Ja
Aantal producten inbegrepen:	- stuk(s)
Type beeldscherm:	LCD
Ingebouwde optical-drive:	Nee
Infrarood (IR) audio-zender:	Ja