Pyle PLUTV63BTA Handleiding

Pyle Speaker PLUTV63BTA

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PLUTV63BTA (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
5
Marine/PowerSports Tower Technical Specs:
Speaker Power: 1200 Watt MAX
Amp Power: 2 x 250 Watt MAX @ 4 Ohms (2 x 125 Watt RMS)
Amp Type: 2-Channel, Class D
Marine Grade Waterproof Rating: IP-X6
Speaker Type: Polypropylene Cone, Butyl Rubber Surround (x2)
Tweeter Type: Neodymium Dome (x2)
Impedance: 4 Ohm
Magnet Type: 32 oz. Circuit
Mid-Woofer Voice Coil Type: 1'', TIL
Sensitivity: 92 dB +/- 2 dB @ 1M/1W
Anti-Thump Turn-On
Soft Turn On/O
T.H.D: <0.05%
S/N Ratio: >80dB
Channel Separation: >65dB
Fuse: 1 x 15A
Power Supply: DC 12V
Universal Mounting Brackets Roll-Bar/Roll-Cage Diameter: 1.75’ ~ 3.0’ –inches
1.75”~2” for Motorsports/Powersports Application.
2.25”~3” for Marine Application.
Speaker Dimensions: 8.1’ x 8.9’ x 10.5’ -inches, with Bracket (-Each)
www.PyleUSA.com
PLUTV63BTA Installation
Speaker Mounting suggestion as below:
Step 1: Removing the top half of clamp
Put the PLUTV63BTA speaker in a safe place.
Using the 1/4” Hex key, remove the top clamp bolts.
Step2/3: To adjust mounting clamp angle and speaker position
Diagram A is to show there are four round pins underneath the bottom
base of aluminum die cast clamp, which can be inserted and xed to four
round notch holes on top of plastic cabinet as diagram B shows by every
45 degrees adjustment either at clockwise or counter clockwise direction.
Through such design, user can change the angle of swivel clamp, use the
5/16” hex key to loose the center screw a little bit and lift the bottom clamp
to twist speaker angle by every 45 degrees to get the optimal angle you
want. Then re-making sure the pins on base of bottom clamp are inserted
and sits on notch holes on top of plastic cabinet at and seamlessly.
Then re-tighten the center hex screw to secure the bottom clamp strongly.
2
www.PyleUSA.com
Step 4: Securing clamp bolts
Using the correct rubber pads (labeled for O.D.) install on both top and
bottom half of clamps. 3.15” x 1.2” x 0.2” rubber pads for 1.75” O.D. 3.15” x
1.2” x 0.08” rubber pads for 2” - 3” O.D. Using the 1/4” Hex bit socket hand
tighten the bolts evenly (both sides should have the same spacing
between bolts).
Step 5: Option for adjustable PYLE logo---Unbolt the screws rst, adjust the logo
direction, then re-x screws.
PLUTV63BTA Wiring
1. Connect the RCA plugs (red/white) to an external amplier for audio output.
2. Connect the ACC wire (red) to the accessory power of the vehicle as ON/OFF
switch of the speakers.
3. Connect the remote out wire (blue) to an external amplier as ON/OFF switch
of the amplier.
3
www.PyleUSA.com
Features:
Pro Audio PowerSport Speakers
Amplied (Active) Speaker System
Wireless BT Music Streaming Ability
Bridged Sound System: (2) x 6.5'' Woofers + (2) x 1’ Tweeters
Marine Grade Waterproof Rated Construction
Weatherproof & Water-Resistant Housing
2-Way Full Range Stereo Sound Reproduction
Built-in Digital Sound Processing Amplier
Integrated Speaker Power & Wiring Harness
Compact Size & High-Powered Output
Impressive Bass Response
Aux (3.5mm) Input Jack
Connect & Stream Audio from External Devices
Sleek Design, Machine Molded Speaker Cabinet Housing
Rugged, Universal Mount Bracket Design for Roll-Bar/Roll-Cage
Used for O-Road Outdoor Vehicles: ATV, UTV, 4x4, Jeeps, Marine Watercraft
Pre-Amp RCA Out to Any OEM/Factory-Made Mono-Block/Full-Range Amplier
BT Connectivity:
Simple & Hassle-Free Pairing
Instant Wireless Audio Streaming Ability
Works with All of Today’s Latest Devices (Smartphones, Tablets, Laptops, etc.)
BT Version: V5.0
BT Network Name: ‘PyleUSA
Wireless Range: 30+ ft.
*BT Receiver Module Built-Into Amplier of Main / Active Speaker
What’s in the Box:
(1) 6.5'' Amplied Main Speaker
(1) 6.5'' Aluminum Mounting Brackets
(2) 3” Aluminum Mounting Brackets (Pre-Installed on Speakers)
(4) 3.15” x 1.2” x 0.2” Inches Rubber Pads
(4) 3.15” x 1.2” x 0.08” Inches Rubber Pads
(4) M8 x 55mm Hexagon Socket Head Cap Screws
(4) M8 x 35mm Hexagon Socket Head Cap Screws (Pre-Installed)
(1) Power Wire Harness
4
www.PyleUSA.com
12V wire harness connection
Black -
Gray +
AUX input
(2)
ACC wire
(red)
(1)
Audio output
(3)
Remote out
wire (blue)
Ground wire
(black)
Battery wire
(yellow)
DC12 (-) grounded to
metal chassis, or directly
to negative polarity of battery
DC12 (+) extention
power cable with fuse
holder (not included)


Product specificaties

Merk: Pyle
Categorie: Speaker
Model: PLUTV63BTA

Heb je hulp nodig?

Als je hulp nodig hebt met Pyle PLUTV63BTA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Pyle

Pyle

Pyle PLUTV40BTA Handleiding

19 Februari 2025
Pyle

Pyle PLMR62 Handleiding

28 Januari 2025
Pyle

Pyle PNX8BK Handleiding

5 December 2024
Pyle

Pyle PDWR40W Handleiding

5 December 2024
Pyle

Pyle PDIC81RD Handleiding

5 December 2024
Pyle

Pyle PLATV65BT Handleiding

5 December 2024
Pyle

Pyle PDIC60 Handleiding

5 December 2024
Pyle

Pyle PDIW67 Handleiding

5 December 2024
Pyle

Pyle PHSP6K Handleiding

5 December 2024
Pyle

Pyle PDIC1681RD Handleiding

5 December 2024

Handleiding Speaker

Nieuwste handleidingen voor Speaker