Pyle PIC62A Handleiding

Pyle Speaker PIC62A

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PIC62A (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

1.Introduction

The Pyle Home PIC62A Directional In-

Ceiling Speaker System designed

s p e c i f i c a l l y w i t h H o m e T h e a t e r

systems applications. The PIC62A

features drivers mounted at a 15”

angle, allowing you to focus sound

proj ecti on to a specific listening

position. These Pyle Home speakers

feature a 2 Way design with a UFLC(Urethane Film Laminated Cloth) woofer, and

Adjustable Silk dome Tweeters. This set Includes in-stallation hardware, and paint

trim ring s. Pre con str ucti on brac kets ar e ava ilab le

seperately.

NOTE: Although this speaker uses a 6.5 driver, it is

mounted in an 8” speaker frame, which means it requires

an 8” speaker pre-construction bracket.

Disclaimer: Make sure you are in compliance with local

building codes before installing this speaker, The Pyle

Home PIC62A In-Ceiling Speaker is suitable for moisture rich environments

such as bathrooms or saunas, but not outdoor applications.

INSTRUCTION &

INSTALLATION SHEET

PIC62A Directional In-Ceiling Speaker

2.Description

The PIC62A made from a durable, seml-flexible plastic material that feature built in foam

gaskets to minimize vibration and maximize the installation seal. They also feature a

perforated metal grill with an acoustically transparent scrim cloth to enhance the speakers

appearance once installed. Pyle Home In-Ceiling speakers are paintable, and well suited for

moisture rich environments. They also feature filp out tabs for easy installation and removal.

3.Installation

Installation of this PIC62A In-Ceiling speakers can be easily accomplished at multiple stages of

the construction process, whether it be “Rough In” (before drywall) or “Trim-Out” (after dry wall is

installed and painted)

A. “Rough-in” steps:

NOTE: It is recommended that a minimum of 16 gauge, 4 conductor

wire be used for most applications from the amplifier or volume

control to this speaker. Different gauges can, and should, be used

based upon the distance of the intended run or quality of

installation(see Figure2).

www.pyleaudio.com

Speaker Wire

Gauge Selection Chart

Distance

<10 Feet

10-50 Feet

>50 Feet

Gauge

Figure 2

Figure 1

(shown with grill removed)

INSTRUCTION &

INSTALLATION SHEET

PIC62A Directional In-Ceiling Speaker

1.Run x/4 conductor (x=gauge preference) stranded speaker wire

from the distribution/volume control to the speaker location (pre-

wiring).

2.If PYLEAUDIO Speaker Pre-Construction Bracket is to be used,

skip to Step “5” .

3.If pre-wiring without using the PYLEAUDIO Pre-Construction

Speaker Brackets, leave 4 to 6 feet of wire at the speaker's

intended location. Use a strip of cardboard stapled to the

joints/studs with a hole through it as a wire place holder for the

drywall installers if installation of the speakers is intended ( see

Figure 3).

4.After drywall and/or painting is complete, push wire though hole,

center template over hole, mark with a pencil and cut out with a

drywall knife.

5 When using the PYLEAUDIO Pre-Construction Bracket (see .

figure 4), leave a coil of speaker wire on top of the bracket coiled

around the speaker mounting hole. There are clips on the corner of

the bracket to secure the speaker wire. Leave enough speaker wire

to be able to pull the wire through the speaker after the drywall is

installed. Strip off 3 inches or so of the speaker cable jacket to

expose the positive and negative insulate wires. Strip 3/8-1/2 inch

of insulation off of these conductors.

6 It is recommended to place insulation behind the speaker to .

provide some damping for the woofer driver. This will yield the best

p o s s i b l e s o u n d. P YL EA U DI O r e c o m me n d s us i n g p o l y -

encapsulated insulation such as Johns Manville Comfort Therm. If

a defined, consistent sound is desired to yield the ideal cubic

footage for the driver. Insulation would then be put in this space

during speaker installation .Refer to blocking chart for details.

7 If installing the speaker in a space with an attic above it is .

recommended that the speaker be boxed in with 1/2 inch MDF

(medium density fiber board) or plywood with insulation installed.

This will provide a defined acoustic space and protect the speaker.

The best possible sound will be achieved by doing this. Refer to

the blocking chart for details.

www.pyleaudio.com

NOTE: Make sure you are in compliance with local building codes before installing this

speaker in an attic space.

Figure 4

Figure 3

Please P ull Thr u Dry -Wal l Here

Insulation

Batting

2 x 10 Joists

16” on Center

Blocking

Distance

B. “Trim-out steps:

1 After drywall and/or painting is complete, push the speaker wire .

through hole, center template over hole, mark with a pencil and cut

out with a dry-wall knife.

2 Hold the speaker with one hand,(if speaker grill is off, pay careful .

attention to push on the woofer's cone, this can cause not

permanent distortion of the voice coil, thus producing a mechanical

rubbing sound or speaker failure),push in the speaker terminal

connectors and insert wires; remove speaker grill. Be sure to have

the positive wires in the RED terminals and the negative wires in

the BLACK terminals.

NOTE: Wiring both drivers of this speaker identically as the

above instruction states will yield a speaker whose drivers are

“in phase”. If one speaker driver is wired opposite of the other,

the speaker drivers will be “out of phase” with one another. If

the speaker drivers are “out of phase” the sound might appear

smeared (canned) and a significant loss of bass might be

noticeable due to phase cancellation. Make sure every

installed speaker is correctly phased.

3 Rotate the speaker driver towards the listening area and use one .

hand to push the speaker into the cut out (again, pay careful

attention to push on the woofer's cone this can cause not

permanent distortion of the voice coil, thus producing mechanical

rubbing sound or speaker failure) and the other to turn the screws

that engage the installation tabs (see ). Tighten the tabs in Figure5

a cross or X-pattern until “snug”. Be careful not to over tighten the

tabs or damage could result. The speaker should appear flush to

the surface.

NOTE: If using a cordless drill/screwdriver, it is suggested that

the screws be turned until almost tight, then finish tightening

via a hand screwdriver.

www.pyleaudio.com

NOTE:A strip of grill adhesive is provided to more securely attach the speaker grills on

final installation. Simply insert several short strips evenly around the grill slot prior to

installing the grill cover. Prior to final installation of the grill, adjust the tweeter for

optimum sound at the listening area.

6.5” Speaker (0.7 CuFt) Blocking Distance

16” on Center, 2x4

16” on Center, 2x6

16” on Center, 2x8

16” on Center, 2x10

16” on Center, 2x12

24” on Center, 2x4

24” on Center, 2x6

24.00”

15.25”

11.50 ”

9.00”

7.50”

15.50”

10.00”

8” Speaker (2.1 CuFt) Blocking Distance

16” on Center, 2x4

16” on Center, 2x6

16” on Center, 2x8

16” on Center, 2x10

16” on Center, 2x12

24” on Center, 2x4

24” on Center, 2x6

71.5”

45.50”

34.50”

27.00”

22.25”

46.00”

29.50”

PYLEAUDIO Speaker Bl ocking

Chart

Size/Type

Efficiency

Power(R MS/Peak)

Frequen cy Response

Woofer Type

Tweeter Type

Impedan ce

6.5” In-Ceiling

88dB

125W/25 0W

45-20KH z

Polypropylence

UFLC Adjustable

4-8 Ohm

Spea ker

Spec ifications

Figure 5

PIC62A

INSTRUCTION &

INSTALLATION SHEET

PIC62A Directional In-Ceiling Speaker

3260100334, IC62A说明书：A3纸，P

105G铜版纸单色印刷说明书,A版.

Product specificaties

Merk:	Pyle
Categorie:	Speaker
Model:	PIC62A
Kleur van het product:	Wit
Hoogte:	119.88 mm
Connectiviteitstechnologie:	Bedraad
Diameter:	279.90 mm
Gemiddeld vermogen:	125 W
Impedantie:	8 Ohm
Geschikt voor buitengebruik:	Nee
Audio-uitgangskanalen:	2.0 kanalen
Speaker plaatsing:	Inbouw in de muur/plafond
Aantal drivers:	2
Woofer:	Ja
Peak Music Power Output (PMPO):	250 W
Frequentiebereik:	45 - 20000 Hz
Gevoeligheid:	88 dB
Luidspreker soort:	2-weg
Diameter woofer:	6.5 "
Tweeter:	Ja
Driver cone material:	Polypropyleen