Pioneer S-1EX Handleiding

Pioneer Speaker S-1EX

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer S-1EX (27 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/27
2
En
Thank you for buying this Pioneer product. Please read
through these operating instructions so you will know how to
operate your model properly. After you have finished reading
the instructions, put them away in a safe place for future
reference.
What’s in the box
Features of this speaker system
• Construction follows leading-edge TAD technology
• Beryllium dual-concentric tweeter
• Aramid/carbon fiber reinforced composite 18 cm woofer
• Perfect time alignment design
Before you start
• The nominal impedance of this speaker system is 6 Ω.
Connect the speaker system to an amplifier with a load
impedance ranging from 4 to 16 (a model with “4 –Ω Ω
16 Ω” displayed on the speaker output terminals).
• Do not touch the speaker cones as they are easily
damaged.
• Do not place magnetic objects such as screwdrivers or
iron parts near the tweeter or midrange. Since the
speakers use strong magnets, the objects may be
attracted, causing injury or damaging the diaphragm.
In order to prevent damage to the speaker system resulting
from input overload, please observe the following precau-
tions:
• Do not supply power to the speaker system in excess of
the maximum permissible input.
• When connecting or disconnecting anything in your AV
system, make sure the amplifier is switched off.
• When using a graphic equalizer to emphasize loud
sounds in the high-frequency range, do not use exces-
sive amplifier volume.
• Do not try to force a low-powered amplifier to produce
loud volumes of sound (the amplifier’s harmonic
distortion will be increased, and you may damage the
speaker).
Caution: installation
• Do not place the speaker on an unstable surface. It
could present a hazard if it falls, as well as damaging the
equipment. If placing the speaker on a thick carpet, we
recommend using the supplied speaker spikes for
stability.
• Switch off and unplug your AV equipment and consult
the instructions when connecting up components. Make
sure you use the correct connecting cables.
• Do not put a TV or other AV equipment on top of this
speaker. It could present a hazard if it falls, as well as
damaging the equipment.
• Do not install your speakers overhead on the ceiling or
wall. If improperly attached, the speaker grille can fall
and cause damage or personal injury.
• Do not attach these speakers to the wall or ceiling. They
may fall off and cause injury.
Caution: in use
• Do not use the speaker to output distorted sound for
long periods of times. This can result in a fire hazard.
• Do not sit or stand on the speaker, or let children play on
the speaker.
• Do not put large or heavy objects on top of the speaker.
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.
D36-P4_A_En
Wash hands after handling
Installing your speaker
Please observe the following points when installing speakers:
•Sounds played through speaker systems are easily
affected in subtle ways by the conditions in the listening
space.
•On the rear of the speaker is a hole provided to attach a
metal catch. This is for stabilizing the speaker so that in
the event of an earthquake etc., the speaker does not fall
over. Use the supplied screws to attach the catches.
• •Spike bases x4 Nuts (for spikes)
x4
•Hex wrench
x1
• •Metal catch x1 Screw (for metal catch)
x1
•Fastening screws
(for grille) x4
•Finishing screws
(for grille) x4
•Caps x10
•Grille x1
•Operating instructions
3
En
English
•Screw two picture hooks or similar into the wall behind
the speaker. Pass a chain or cord around the hooks and
through the metal catch so that the speaker is stabilized
(make sure to test that it supports the weight of the
speaker).
•After installing, make sure the speaker is securely fixed.
•For good sound, the speaker should be about 20 cm
away from the back wall and at least 50 cm away from
the side wall. If the room has a lot of reverberation, we
recommend hanging heavy fabric on the walls, and/or
putting a carpet on the floor to damp the sound. For best
results, cover walls completely.
•Place speakers equal distances from your listening
position for good stereo sound. Use speaker cords of the
same length for each speaker.
•If you are using a set of speakers for your TV sound,
install the speakers at equal distances either side of the
TV and point them in the same direction as the TV.
•Do not place the speaker where it will be in direct
sunlight, and avoid positioning it near heaters and air
conditioners. This may cause warping and discoloration
of the speaker cabinet and damage the speaker.
•Pioneer assumes no liability whatsoever for damages
resulting from assembly, improper mounting, insuffi-
cient reinforcement, misuse of the product, acts of
nature, etc.
Using the spikes
There are four metal spikes built-in to the speaker base that
you can use to isolate the speaker from the floor. Spikes are
recommended when placing the speakers on a thick carpet
(for added stability), or for better sound when placing the
speakers on a hard reverberant surface (such as a concrete
or wood floor). Use the supplied spike pads to avoid scratch-
ing the floor or other surface where the speaker is placed.
1 Choose the location for speaker placement then put
the spike bases on the floor.
2 Remove the protective cover from the top of the leg
support.
3 Place the speaker upright so that the corners are
resting on the spike bases on the floor.
4 Insert and turn the supplied hex wrench until the
spike protrudes from the base.
Do this in turn for each spike, making sure all four corners
are of even height and the speaker is stable and resting
squarely on all four spikes.
5 After the spike lengths are even, tighten the nuts to
fix the spikes in place.
Caution: when using the spikes
•Note that these spikes are sharp metal and can cause
damage to flooring. Make sure to lay down a cloth or
suitable base before setting up.
•The speaker is very heavy (about 66 kg) and can cause
serious damage or injury if you are attempting to tighten
the nuts with the speaker standing or leaning. Make
sure to lay down a cloth and tighten the nuts with the
speaker laying flat. Two people or more during place-
ment and setup is advised.
Hex wrench
Protective covers
Metal catch
20 cm
50 cm

Product specificaties

Merk: Pioneer
Categorie: Speaker
Model: S-1EX

Heb je hulp nodig?

Als je hulp nodig hebt met Pioneer S-1EX stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker Pioneer

Pioneer

Pioneer TS-A4671F Handleiding

13 December 2024
Pioneer

Pioneer TS-A6881F Handleiding

13 December 2024
Pioneer

Pioneer TS-A6961F Handleiding

13 December 2024
Pioneer

Pioneer TS-A1371F Handleiding

13 December 2024
Pioneer

Pioneer TS-A1671F Handleiding

13 December 2024
Pioneer

Pioneer TS-M801PRO Handleiding

13 December 2024
Pioneer

Pioneer TS-M651PRO Handleiding

13 December 2024
Pioneer

Pioneer TS-W3020PRO Handleiding

13 December 2024
Pioneer

Pioneer TS-6900PRO Handleiding

13 December 2024
Pioneer

Pioneer TS-G6930F Handleiding

13 December 2024

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Sven

Sven MC-5 Handleiding

20 December 2024
Sven

Sven SPS-535 Handleiding

20 December 2024
Devialet

Devialet Mania Deep Handleiding

19 December 2024
Kicker

Kicker Premium 51MSC65 Handleiding

18 December 2024
Kicker

Kicker Premium 51MSC8 Handleiding

18 December 2024
Monitor Audio

Monitor Audio Apex A10AV12 Handleiding

17 December 2024
Audac

Audac ATEO6M Handleiding

17 December 2024
Audac

Audac CIRA724I Handleiding

17 December 2024
NGS

NGS WILD Space 3 Handleiding

16 December 2024
HK Audio

HK Audio LINEAR 3 112 XA Handleiding

16 December 2024