Pioneer PDP-S09-LR Handleiding

Pioneer Speaker PDP-S09-LR

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer PDP-S09-LR (28 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

PDP-S09-LR

Operating Instructions

Mode d'emploi

Bedienungsanleitung

Istruzioni per l'uso

Gebruiksaanwijzing

Manual de instrucciones

Speaker System

Enceintes acoustiques

Lautsprechersystem

Sistema di diffusori

Luidsprekersysteem

Sistema de altavoces

English

CHECKING THE ACCESSORIES

7Speaker cable x 2

Thank you for buying this Pioneer product.

Please read through these operating instructions before

using your speaker system so you will know how to make

the most of its performance. After you have finished reading

the instructions, put them away in a safe place for future

reference.

BEFORE USE

÷The nominal impedance of this speaker system is 8 ohms.

÷In order to prevent damage to the speaker system

resulting from input overload, please observe the

following precautions:

÷Do not supply power to the speaker system in

excess of the maximum permissable input. This

can result in damage or a possible fire hazard.

÷When connecting or disconnecting pin-plugs, be

sure that amplifier power is OFF.

÷When using a graphic equalizer to emphasize loud

sounds of a high frequency range, do not use

excessive amplifier volume.

÷Do not force a low-powered amplifier to produce a

loud volume of sound (the amplifier’s harmonic

distortion will be increased, and you may damage

the speaker).

÷Please handle the speakers with sufficient care, as

the grille net and the cabinet can become damaged

or broken when they are subjected to strong external

impacts.

÷Placing a CRT computer screen or CRT monitor near to

the speakers may result in interference or color distortion.

If this happens, distance the monitor from the speakers.

This product is designed exclusively for use with the

PDP-4330HD,PDP-433HDE,PDP-433HDG Pioneer plasma

display.

7Operating Instructions

Flat countersunk head screw x 4

Hexagon socket head screw x 4

7Speaker mounting fittings

For top right side x 1 For top left side x 1

For bottom x 2

7Speaker mounting bolts

7Mounting tool (Hex wrench)

NOTE:

Always use the accessory mounting fittings for

installation.

When screws other than those enclosed as accessories

are used to install the speakers, the speakers may drop

off or accidents may be caused. Always use the screws

enclosed as accessories.

INSTALLATION ON THE PLASMA

DISPLAY

Perform installation according to the following steps to 1 2.

1Attach the mounting fittings to the

speakers.

The illustration shows the right speaker.

For top side

Mounting plate

Flat countersunk

head screw

For bottom

1 The top side fittings are dif-

ferent for the right and the

left side, and they must be

matched correctly.

2 Install the mounting fittings

with bolts at the positions

shown in the figure on the

left.

Notes on Installation Work:

This product is marketed assuming that it is installed by

qualified personnel with enough skill and competence.

Always have an installation specialist or your dealer install

and set up the product.

PIONEER cannot assume liabilities for damage caused

by mistake in installation or mounting, misuse,

modification or a natural disaster.

CAUTION

English

NOTE:

When the display is to be moved after speaker

installation, do not hold the display by the speakers. Hold

the bottom of the display to move it.

The grille nets are designed to protect the speakers,

however excessive force (such as pushing on, or insert-

ing objects between the grille nets) may result in dam-

age.

2Attach the speakers to the display.

Install the unit marked "RIGHT" on the right side of the display.

Hexagon socket

head screw

Plasma display

Install the unit marked "LEFT" on the left side of the display.

Hexagon socket

head screw

1To attach the speakers to the display, start by placing the

upper screw where indicated, tightening until there is a

small space of about 5mm between the head of the screw

and the display.

2Check the rear of the speakers for the LEFT and RIGHT

indicators to make sure you are attaching the correct

speaker to the corresponding right or left side. Make sure

the UP mark is pointing up, and then attach the speaker

by fitting the upper mounting over the head of the screw

and sliding down until snug.

3Affix the lower fitting to the display and tighten the screw

about halfway.

4 Adjust the position so that the gap between the speaker

and the display is uniform, and then tighten the screws

firmly.

Plasma display

1Switch off the power of the plasma display.

2Connect the input terminals of the speaker system and

the speaker output terminals of the plasma display with

the accessory speaker cable. Make sure the positive (ª)

and negative ( ) terminals match when connecting.·

To the terminal·To the terminalª

(Speaker output terminals of the plasma display)

· terminal (black)

2. Push the lever, insert the cable into the hole, and release the lever.

1. Remove the insulation and twist the core ends together.

ª terminal (red)

CONNECTION TO A PLASMA

DISPLAY

1Connecting the speaker cables

÷After connection to the terminals, pull lightly on the cable

to confirm that the tips of the cable are properly connected

to the terminals. An imperfect connection can cause

sound interruptions and noise.

÷ ª ·When cable cores stick out and and lines are short-

circuited, an excessive load will be applied to the plasma

display and the operation will stop or trouble will be

caused.

÷When the polarity is reversed for one speaker (left or right)

at the time of connection to the plasma display, the bass

reproduction will be reduced, the sound positioning will

be lost, and a correct stereo effect will not be obtained.

Input terminal of speaker

3. For the input terminals on the plasma display, push the tab to the

open position, and insert the wire. Then, close tab firmly to secure

the wire in place.

ª · · ª

R L

Input terminal of plasma

display

Black

Red

Product specificaties

Merk:	Pioneer
Categorie:	Speaker
Model:	PDP-S09-LR
Kleur van het product:	Zilver
Gewicht:	1600 g
Breedte:	74 mm
Diepte:	101 mm
Hoogte:	630 mm
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Gemiddeld vermogen:	- W
Equalizer-instellingen:	Nee
Aanbevolen gebruik:	Overige
Impedantie:	8 Ohm
Audio-uitgangskanalen:	2.0 kanalen
Speaker plaatsing:	Muur-montage
Aantal drivers:	2
Woofer:	Ja
Frequentiebereik:	60 - 20000 Hz
Gevoeligheid:	82 dB
Versterkeraansluiting (binding post):	Ja
Luidspreker soort:	2-weg
Diameter hogetonenluidspreker:	25 mm
Tweeter:	Ja