Pioneer HTZ-434DVD Handleiding
Pioneer
Home cinema set
HTZ-434DVD
Lees hieronder de π handleiding in het Nederlandse voor Pioneer HTZ-434DVD (3 pagina's) in de categorie Home cinema set. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/3
Setting up your DVD/CD Receiver
1
1 2 3
Check that you have all the accessories, then put
the batteries in the remote control.
Video cord
Batteries and
remote control
FM antenna
Microphone
(for Auto MCACC setup)
AM loop antenna
2
Connect the AM and FM antennas to the rear panel of the DVD/CD receiver.
1
2
3
Push open the tabs, then insert
one wire fully into each terminal.
Release the tabs to secure the AM
antenna wires.
Pull off the protective shields
of both AM antenna wires.
4
Fix the AM loop antenna to the
attached stand.
To fix the stand to the antenna, bend in the
direction indicated by the arrow (fig. A) then
clip the loop onto the stand (fig. B).
Note: If you plan to mount the AM antenna
to a wall or other surface, secure the stand
with screws ( ) before clipping the loop fig. C
to the stand. Make sure the reception is clear.
5 6
Place the AM antenna on a flat
surface and point in the direction
giving the best reception.
Donβt let it come into contact with metal
objects and avoid placing near computers,
television sets or other electrical appliances.
Connect the FM wire antenna to the FM UNBAL 75 antenna terminal.β¦
For best results, extend the FM antenna fully and fix to a wall or door
frame. Donβt drape loosely or leave coiled up.
Note:
The signal earth ( ) is designed to reduce noise that occurs when an H
antenna is connected. It is not an electrical safety earth.
When connecting this system or changing connections, be sure to switch the power off with the STANDBY/ON button, and disconnect the power cord from the AC outlet.
Do not use these speakers with any other system or amplifier as this may result in damage or fire.
3
Connect each speaker using the color-coded
speaker cords. Match them to the colored
speaker terminals on the rear panel of the
DVD/CD receiver.
1
2
3
Connect each speaker as shown below.
Twist and pull off the protective
shields on each wire.
Connect the wires to the
speaker. Match the colored
wire with the color-coded
label (above the tabs), then
insert the colored wire into
the red (+) tab and the other
wire with the black (β) tab.
For the best surround sound, setup your speakers as
above. The front left and right speakers should be
about 1.8 2.7 m apart.β
Congratulations! You're done setting up.
Printed in <XRE3103-A>
These speaker terminals can be hazardous when live. When you connect or
disconnect the speaker cables, to prevent the risk of electric shock, do not
touch uninsulated parts before disconnecting the power cord.
Connect the DVD/CD receiver to your TV, then connect the
supplied power cord.
3Connect the power cord to the AC inlet.
2
Connect one end to a video input on your TV.
Use the supplied video cord.
4
1
Using the remote control
The remote control can be used within a range of about 7
meters from the remote sensor on the front panel, and
within a 30 degree angle.
Precautions:
β’ The remote control may not work if there is an obstacle
between the remote control and the display unit, or if the
remote control is not directed towards the remote sensor
of the display unit at the correct angle.
β’ The remote control may not work properly if strong
light such as direct sunlight or fluorescent light is shining
onto the unitβs remote sensor.
β’ The remote control may not work properly when this
unit is used near devices emitting infrared rays, or when
remote controls of other devices which use infrared rays
are used. Also, the use of this remote control may cause
other devices to work improperly.
β’ When the operating range of the remote becomes too
short, replace the batteries.
Remote control battery caution
Incorrect use of batteries may cause leakage or
rupture.
Always be sure to follow these guidelines:
β’ Always insert batteries into the battery compartment
correctly matching the positive Βͺ and negative Β·
polarities, as shown by the display inside the
compartment.
β’ Never mix new and used batteries.
β’ Batteries of the same size may have different voltages,
depending on brand. Do not mix different brands of
batteries.
β’ When disposing of used batteries, please comply with
governmental regulations or environmental public
instruction's rules that apply in your country or area.
β’ In order to prevent battery leakage, remove the
batteries when not using the remote control for an
extended period (one month or more). If leakage occurs,
carefully wipe away any battery fluid inside the
compartment, and replace the batteries with new ones.
β’ Do not allow books or other objects to rest on top of
the remote control, since the buttons may be depressed,
causing faster exhaustion of the batteries.
Additional notes on connecting antennas
β’ Keep antenna cables away from the main unit and other
cables.
β’ To assure optimum reception, pull the FM antenna so that it is
fully extended and not coiled or hanging at the rear of the unit.
β’ If reception with the supplied antenna is poor, see the Other
connections section in the main operating instructions for details
on connecting outdoor antennas.
Additional notes on speaker placement
If your listening room is of adequate size, place the speakers as
shown in step 3 to achieve the optimum surround sound effect.
If you are listening in a fairly small room and a typical surround
speaker setup is not possible, see in Home theater sound setup
the instruction manual and the for Speaker Setup guide
information on the Front surround 3-spot setup option.
When using the standard surround speaker setup as shown in
step 3, please observe the following guidelines:
β’ Install the main front left and right speakers at an equal
distance from the TV.
β’ For optimum effect, install the rear speakers slightly above ear
level.
β’ Install the center speaker above or below the TV so that the
sound of the center channel is localized at the TV screen.
Precautions:
β’ When installing the center speaker on top of the TV, be sure
to secure it with tape or some other suitable means. Otherwise,
the speaker may fall from the TV due to external shocks such as
earthquakes, endangering those nearby or damaging the speaker.
β’ Do not connect the supplied speakers with any other
amplifier. This may result in malfunction or fire.
β’ The front, center and surround speakers supplied with this
system are magnetically shielded. However, depending on the
installation location, color distortion may occur if the speaker is
installed extremely close to the screen of a television set. If this
happens case, turn the power switch of the television set OFF,
and turn it ON after 15 to 30 minutes. If the problem persists,
place the speaker system away from the television set.
β’ The subwoofer is not
magnetically shielded
and so should not
be placed near a TV or monitor.
Since it is not magnetically
shielded, do not place any magnetic storage media (such as floppy
disks and tape or
video cassettes) close to the subwoofer.
β’ Do not fix the front, center speakers and subwoofer to the
wall or ceiling; they could cause injury if they fell.
Connect the other end to the video output of the DVD/CD receiver.
This player is equipped with copy protection technology. Do not connect this
player to your TV via a VCR using AV cables, as the picture from this player will not
appear properly on your TV.
ST+
TUNE+
ENTER
TUNEβ
MASTER
VOLUME
STβ
STANDB Y/ON
CD FM/AM
OPEN CLOSE
DVD TUNER TV L INE
L1/L2
1
4
4
Β‘
8
3
7
0
DVD MENU
RETURN
B ASS
MODE
TV CONTROL
CH VOL
INPUT
OPEN
MUTE
Color-coded wire
(Connect to speaker)
Color-coded connector
(Connect to rear panel)
FRONT
S URR OUND
Connect the other end to the color-
coded speaker terminals on the
rear of the DVD/CD receiver (as
shown at left). Make sure to insert
completely.
The small lug at the wire-end of the
speaker plug should face up or
down depending on whether it's
being plugged into one of the
upper or lower three speaker
terminals. Please make sure to
connect correctly.
Upper three terminals
Lower three terminals
* Illustration shows
the Taiwan model
ANTENNA
3
1
2
4
6
fig. A fig. B fig. C
FM
UNBAL 7 5β¦
AM
LOOP ANTEN NA
6 6
6 6
6
6
OUTIN
FRONT CENTER
MCACC
MIC
SURROUND
SUB
WOOFER
R
L
RR
LL
LINE 1
AUDIO
SPEAKERS
TV
IN
6 6
6 6
6
6
FM
UNBAL 75β¦
AM
LOOP ANTENNA
OPTICAL IN
OUT
VIDEO
OUT
IN
FRONT CENTER
MCACC
MIC
SURROUND
S UB
WOOFER
R
L
RR
LL
LINE 1
LINE 2
AC IN
AUDIO
ANTENNASPEAKERS
IN
TV
AUDIO
IN
CONTROL
S-VIDEO
OUT
COMPONENT
VIDEO OUT
PR
PB
Y
VIDEO
VIDEO
OUT
VIDEO
VIDEO IN
To AC outlet
AC IN
Listening position
Subwoofer (Purple)
Front right
(Red)
Front left
(White)
Surround left
(Blue)
Surround right
(Grey)
Center (Green)
* Illustration shows the Taiwan model
* Illustration shows the Taiwan model
Power cord
*
Speaker Setup Guide
What's in the box
β’ Front speakers x 2
β’ Center speaker x 1
β’ Surround speakers x 2
β’ Subwoofer x 1
β’ Speaker cords:
Red/White (Front speakers)
4 m x 2
Green (Center speaker) 4 m x 1
Blue/Grey (Surround speakers)
10m x 2
Purple (Subwoofer) 4 m x 1
β’ Non-skid pads (small) x 4
β’ Non-skid pads (large)
Taiwan model x 4
All other models x 6
β’ Front speaker stand bases
x 2
β’ Screws (for bases) x 6
β’ Brackets x 2
β’ Screws (for brackets) x 4
β’ Mounting brackets x 2
*
β’ Screws
(for mounting brackets) x 2
*
2
4
Connect the speaker system.
1
Center speaker
1
Center speaker
52 3
ExtPowerFrtMovie FrtMusic /
Attach the large non-skid pads to the base of the subwoofer.
Use the supplied adhesive to attach 6 pads to the base of subwoofer.
Placing the Subwoofer (Taiwan model only)
Choose your subwoofer placement
The subwoofer supplied with this
system can be placed upright or
on its side (flat). Choose the
position that works best for your
room, then attach the large non-
skid pads as shown at right.
Upright position Flat position
Attach the non-skid pads to the Subwoofer
: Non-skid pads
(
Singapore/Indonesia/Hong Kong/Phillipines/Malaysia models
)
* Illustration shows the Taiwan model
* Illustration shows the Taiwan model
Attach the speaker stand bases to the stems using the screws provided.
Before securing the base to the stand, thread the speaker wire through the holes provided on the
base as shown below. Then, o
nce you have aligned the stem and base, secure with the small
screws at the points shown at right.
Connect the speaker system.
Refer to the (the other part of this Setting up your DVD/CD Receiver
setup guide)
to connect the speakers properly. Place them as
shown in the diagram at far left optimal surround sound.
Attach the smaller non-skid pads to the
base of the center speaker.
Use the supplied adhesive to attach 4 pads to the
base of center speaker.
This is a standard multichannel surround sound speaker
setup for optimal 5.1 channel home theatre sound.
Standard surround 5-spot setup
Attach the smaller non-
skid pads to the base of
the center speaker.
Use the supplied adhesive to
attach 4 pads to the base of
center speaker.
Place the surround speakers on top of the front
speakers, turn the surround speakers towards
the closest wall, lining the arrows up for
optimal Front Surround.
Turn each surround speaker so that the arrow at the base ξ
is lined up with the arrow on the front ξ FRONT SURROUND
speaker.
This is only necessary with the or FrtMovie
FrtMusic ExtPower modes. With (Extra Power), the
surround speakers should be in the same direction as the
front speakers (as shown below). See the operating
instructions for more on the Front Surround modes.
Secure in position with the brackets provided.
Line up the holes in the bracket with the holes in the speakers
, then secure
with two screws at the points shown below. Make sure you've matched the
right and left brackets with the speakers (as shown).
This setup is ideal when rear surround speaker placement
isn t possible or you want to avoid running long speaker β
cables in your listening area.
Front surround
3-spot setup
When assembling the speakers, lay
them down flat on their side to avoid
accidents or injury. Make sure to use
a stable surface when assembling,
setting up, and placing the speakers.
Assembling the speaker stands and securing your front speakers
Secure the speaker wire.
When you're finished, t
hread
the surround speaker cords
through the outlet on the
back of the speaker stand and
through the base of the
brackets as shown below.
Refer to the (the other part of this setup guide)Setting up your DVD/CD Receiver
to
connect the speakers properly.
Safety precautions
when setting
Front
left
Subwoofer
Front
right
Surround
left
Surround
right
Center
Listening position
Front
left
Subwoofer
Front
right
Surround
left
Surround
right
Center
Listening position
ExtPower
FrtMovie FrtMusic /
Caution
β’ Please don't use the any attachments with the
front speakers other than the brackets provided.
Caution
β’ Please don't use the any attachments with the front speakers
other than the brackets provided.
* Please refer to Wall-mounting
the front and surround speaker
system in the operating
instructions for installation.
Downloaded from manuals search enginewww.Manualslib.com
Downloaded from manuals search enginewww.Manualslib.com
Product specificaties
| Merk: | Pioneer |
| Categorie: | Home cinema set |
| Model: | HTZ-434DVD |
Heb je hulp nodig?
Als je hulp nodig hebt met Pioneer HTZ-434DVD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Home cinema set Pioneer
19 Mei 2023
7 Mei 2023
7 Mei 2023
2 Mei 2023
30 April 2023
20 April 2023
16 April 2023
13 April 2023
29 Maart 2023
26 Maart 2023
Handleiding Home cinema set
- Home cinema set Philips
- Home cinema set Sony
- Home cinema set Samsung
- Home cinema set Panasonic
- Home cinema set LG
- Home cinema set AEG
- Home cinema set Daewoo
- Home cinema set Grundig
- Home cinema set JVC
- Home cinema set JBL
- Home cinema set Kenwood
- Home cinema set Medion
- Home cinema set Onkyo
- Home cinema set Yamaha
- Home cinema set Adler
- Home cinema set Aiwa
- Home cinema set Akai
- Home cinema set Blaupunkt
- Home cinema set Bose
- Home cinema set Dali
- Home cinema set Definitive Technology
- Home cinema set Dell
- Home cinema set Denon
- Home cinema set Eltax
- Home cinema set Fenton
- Home cinema set Focal
- Home cinema set Funai
- Home cinema set GPX
- Home cinema set Harman Kardon
- Home cinema set Hyundai
- Home cinema set ILive
- Home cinema set Iluv
- Home cinema set KEF
- Home cinema set Klipsch
- Home cinema set Konig
- Home cinema set Lenco
- Home cinema set Magnat
- Home cinema set Magnavox
- Home cinema set Marantz
- Home cinema set Meridian
- Home cinema set NAD
- Home cinema set Polk
- Home cinema set Pure Acoustics
- Home cinema set Pyle
- Home cinema set RCA
- Home cinema set Rotel
- Home cinema set Sanyo
- Home cinema set Schneider
- Home cinema set Sharp
- Home cinema set Sherwood
- Home cinema set Sylvania
- Home cinema set Technics
- Home cinema set Teufel
- Home cinema set Thomson
- Home cinema set Wharfedale
- Home cinema set Wolfgang
- Home cinema set Jamo
- Home cinema set Anthem
- Home cinema set Bowers And Wilkins
- Home cinema set Creative
- Home cinema set Edifier
- Home cinema set Nevir
- Home cinema set Majestic
- Home cinema set Canton
- Home cinema set Integra
- Home cinema set Coby
- Home cinema set Audiocore
- Home cinema set Dynaudio
- Home cinema set SVS
- Home cinema set Mitsai
- Home cinema set Fluance
- Home cinema set Amphion
- Home cinema set BBK
- Home cinema set SLS
Nieuwste handleidingen voor Home cinema set
23 November 2024
22 November 2024
22 November 2024
22 November 2024
22 November 2024
22 November 2024
22 November 2024
22 November 2024
22 November 2024
22 November 2024