Pioneer deh-1600r Handleiding

Pioneer Autoradio deh-1600r

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer deh-1600r (6 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

Nota:

• Antes de finalmente instalar la unidad, conecte el

cableado temporalmente y asegúrese de que todo

esté conectado correctamente y que la unidad y

el sistema funcionan debidamente.

• Utilice sólo las piezas que se incluyen con esta

unidad para asegurar la instalación adecuada. El

uso de piezas no autorizadas podría causar fallos

de funcionamiento.

• Consulte con su distribuidor si la instalación

requiere del taladro de orificios u otras modifica-

ciones del vehículo.

• Instale la unidad donde no alcance el espacio del

conductor, y donde no pueda dañar a los

pasajeros si sucediera un paro repentino, como

una detención de emergencia.

• El semiconductor láser se dañará si se sobre-

calienta, por eso no instale la unidad en un lugar

caliente – por ejemplo, cerca de la salida de un

calefactor.

• Si el ángulo de la instalación excede los 60° del

lado horizontal, la unidad podría no brindar su

óptimo funcionamiento. (Fig. 1)

Instalación con tope de goma

(Fig. 2)

1. Tablero de instrumentos

2. Soporte

Después de insertar el soporte en la tabla de

mandos, luego seleccione las orejetas apropiadas

según el grosor del material de la tabla de man-

dos y dóblelos.

(Instale lo más firme posible usando las lengüe-

tas superior e inferior. Para fijar, doble las

lengüetas 90 grados.)

3. Tope de goma

4. Tornillo

Quitado de la unidad (Fig. 3)

5. Inserte las herramientas de extracci n suminis-ó

tradas en la unidad, como se indica en la figura,

hasta que se enganchen en su positión.

Tire de la unidad mientras mantiene las her-

ramientas presionadas contra los lados de la

unidad.

Sobre los tornillos de fijación del

panel delantero (Fig. 4)

6. Tornillos de fijación

Si no desea utilizar la función de extracción y

colocación del panel delantero, utilice los tornil-

los de fijación suministrados y fije el panel

delantero a esta unidad.

Instalación <ESPAÑOL>

Note:

•Before finally installing the unit, connect the

wiring temporarily, making sure it is all connect-

ed up properly, and the unit and the system work

properly.

•Use only the parts included with the unit to

ensure proper installation. The use of unautho-

rized parts can cause malfunctions.

•Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

tions of the vehicle.

•Install the unit where it does not get in the dri-

ver’s way and cannot injure the passenger if there

is a sudden stop, like an emergency stop.

•The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot

— for instance, near a heater outlet.

• ° If installation angle exceeds 60 from horizontal,

the unit might not give its optimum performance.

(Fig. 1)

Installation with the rubber bush

(Fig. 2)

1. Dashboard

2. Holder

After inserting the holder into the dashboard,

then select the appropriate tabs according to the

thickness of the dashboard material and bend

them.

(Install as firmly as possible using the top and

bottom tabs. To secure, bend the tabs 90

degrees.)

3. Rubber bush

4. Screw

Removing the Unit (Fig. 3)

5. Insert the supplied extraction keys into the unit,

as shown in the figure, until they click into place.

Keeping the keys pressed against the sides of the

unit, pull the unit out.

About the fixing screws for the

front panel (Fig. 4)

6. Fixing screw

If you do not operate the Removing and

Attaching the Front Panel Function, use the sup-

plied fixing screws and fix the front panel to this

unit.

Installation <ENGLISH>

INSTALLATION MANUAL

MANUEL D’INSTALLATION

60°

Fig. 1

Abb. 1

Afb. 1

Fig. 2

Abb. 2

Afb. 2

DEH-1630R

DEH-1600R

DEH-1600RB

Printed in China

Imprimé en Chine

<YRD5006-A/U> EW

This product conforms to new cord colors.

Los colores de los cables de este producto se confor-

man con un nuevo código de colores.

Dieses Produkt entspricht den neuen Kabelfarben.

Le code de couleur des câbles utilisé pour ce produit

est nouveau.

Questo prodotto è conforme ai nuovi codici colori.

De kleuren van de snoeren van dit toestel zijn gewijzigd.

Fig. 3

Abb. 3

Afb. 3

Fig. 4

Abb. 4

Afb. 4

Opmerking:

•Voor u het apparaat definitief installeert, is het

raadzaam eerst alle aansluitingen tijdelijk te

maken om te kontroleren of alles naar behoren

funktioneert, zodat u later niet voor verrassingen

komt te staan.

•Gebruik voor het installeren uitsluitend de bij het

apparaat geleverde onderdelen. Toepassing van

andere dan de goedgekeurde onderdelen kan lei-

den tot storing in de werking van het apparaat.

•Raadpleeg uw dichtstbijzijnde dealer als het voor

het installeren van het apparaat nodig blijkt gaten

te boren, of andere wijzigingen aan te brengen

aan de auto.

•Installeer het apparaat op een plaats waar het de

bestuurder niet in de weg kan zitten en waar het

ook bij een noodstop e.d. geen gevaar voor de

inzittenden kan opleveren.

•De halfgeleider-laser in het apparaat is gevoelig

voor beschadiging door oververhitting, dus

installeer het apparaat niet te dicht in de buurt

van de autoverwarming of de warme luchtsroom

daarvan.

•Als u het apparaat onder een al te steile hoek

installeert, d.w.z. meer dan 60 uit het horizon-°

tale vlak, zal het niet naar behoren kunnen

werken. (Afb. 1)

Installatie met de rubber mof

(Afb. 2)

1. Dashboard

2. Houder

Nadat u de houder in het dashboard hebt

geplaatst, kiest u de juiste lipjes voor de dikte

van het dashboard-materiaal en buigt u deze om.

(Plaats zo stevig als mogelijk met gebruik van de

boven- en onderlipjes. Buig de lipjes 90 graden

om te vergrendelen.)

3. Rubber mof

4. Schroef

Verwijderen van het apparaat

(Afb. 3)

5. Steek de bijgeleverde verwijdersleutels in het

apparaat, zoals in de afbeelding aangegeven, tot

ze op hun plaats vastklikken. Houd de sleutels

tegen de zijkanten van het apparaat aangedrukt

en trek het apparaat naar buiten.

Meer over de bevestigingsschroeven

voor het voorpaneel (Afb. 4)

6. Bevestigingsschroef

Indien u de functie voor Los maken en bevesti-

gen van het voorpaneel niet gebruikt, moet u met

de bijgeleverde bevestigingsschroeven het voor-

paneel aan dit apparaat vastzetten.

Installeren <NEDERLANDS>

Nota:

•Prima di installare definitivamente l’apparecchio,

collegare i fili temporaneamente e accertarsi che

tutti i collegamenti siano corretti e che l’apparec-

chio e il sistema funzionino correttamente.

• ’Per un installazione appropriata, usare soltanto i

pezzi in dotazione all’apparecchio. L’uso di pezzi

non autorizzati può causare problemi di funzion-

amento.

•Rivolgersi al più vicino rivenditore se l’instal-

lazione richiede la trapanatura di fori o altre

modifiche del veicolo.

• ’Installare l apparecchio in un punto in cui esso

non intralci le manovre del conducente e in cui

non possa provocare lesioni ai passeggeri nel

caso dell’arresto improvviso del veicolo, come

nel caso di una frenata d’emergenza.

•Il laser a semiconduttore subisce danni se si sur-

riscalda; pertanto, non installare l’apparecchio in

luoghi esposti al calore, come per esempio nei

pressi della bocca di efflusso dell impianto di’

riscaldamento.

• ’ ° Se l angolo di installazione supera i 60 rispetto

alla posizione orizzontale, l’apparecchio potrebbe

non fornire prestazioni ottimali. (Fig. 1)

Installazione con la boccola di

gomma (Fig. 2)

1. Cruscotto

2. Supporto

Dopo aver inserito il supporto nel cruscotto,

selezionare le linguette appropriate a seconda

dello spessore del materiale del cruscotto e pie-

garle.

(Installare quanto pi saldamente possibile ser-ù

vendosi delle linguette superiore e inferiore. Per

fissare, piegare le linguette a 90 gradi.)

3. Boccola di gomma

4. Vite

Estrazione dell (Fig. 3)’unità

5. Inserire le chiavette di estrazione in dotazione

nell’apparecchio, come mostrato nella figura,

finché non scattano in posizione. Tenendo le chi-

avette premute contro i lati dell’apparecchio,

estrarre l’apparecchio.

Viti di fissaggio per il pannello

anteriore (Fig. 4)

6. Vite di fissaggio

Se non si usa la funzione Rimozione e montaggio

del frontalino, usare le viti di fissaggio in

dotazione per fissare il frontalino su questo

apparecchio.

Installazione <ITALIANO>

Remarque:

•Avant de finaliser l installation de l’ ’appareil,

connecter temporairement le câ ’blage en s assur-

ant que tout est correctement connect et queé

l’appareil et le système fonctionnement correcte-

ment.

• ’Pour obtenir une bonne installation, n utiliser que

les pi ces de lè ’appareil. L’ èutilisation de pi ces

non prévues risque de causer un mauvais fonc-

tionnement.

•Consulter le concessionnaire le plus proche si

l’installation nécessite le percement de trous ou

toute autre modification du véhicule.

• ’ à ù êInstaller l appareil un endroit o il ne g ne pas

le conducteur et o il ne peut pas blesser les pas-ù

sagers en cas d t brusque, comme pendant un’arrê

arrêt d’urgence.

• éLe laser semiconducteur sera endommag en cas

de réchauffement excessif. Dans ce cas ne pas

installer l’appareil dans un endroit pr sentant uneé

temp rature é élevée, tel que sortie de chauffage.

•L’ ’ é °angle de l installation, ne doit pas d passer 60

par rapport à l’ ’ éhorizontale, faute de quoi l unit ne

fournira pas ses performances optimales. (Fig. 1)

Installation avec une bague en

caoutchouc (Fig. 2)

1. Tableau de bord

2. Support

Après avoir introduit le support dans le tableau

de bord, sé ílect onnez les languettes appropriées

en fonction de l’épaisseur du matériau du tableau

de bord et courbez-les.

(Assurez le maintien aussi solidement que possi-

ble en utilisant les languettes inférieures et

supérieures. Cela fait, courbez les languettes de

90 degrés.)

3. Bague en caoutchouc

4. Vis

Dépose de l nite (Fig. 3)’ú

5. Ins unitérer les clés d’extraction fournis dans l’ é,

comme indiqu dans la figure, jusqu ce qué ’à ’elles

s s’enclenchent en position. En maintenant ces clé

pressées contre les cô ét s de l’unité, retirer l’unité.

À propos des vis de fixation de la

face avant (Fig. 4)

6. Vis de fixation

Si vous n utilisez pas la fonction de d pose et’ é

pose de la face avant, utilisez la vis de fixation

fournie et fixez la face avant à l’appareil.

Installation <FRAN AIS>Ç

Hinweis:

• ßSchlie en Sie vor dem Einbau die Leitungen

vorübergehend an und stellen Sie sicher, das alles

richtig angeschlossen ist und das Ger t und dasä

System einwandfrei arbeiten.

•Um einwandfreien Einbau zu gewährleisten, soll-

ten nur die mit dem Gerät mitgelieferten Teile

verwendet werden. Bei Verwendung von Nicht-

Originalteilen kann es zu Funktionsstörungen

kommen.

•Wenden Sie sich an Ihren Fachhändler, wenn

zum Einbau des Ger ts L cher gebohrt oderä ö

andere Veränderungen an Ihrem Auto vorgenom-

men werden müssen.

• äBauen Sie das Ger t an einer Stelle ein, wo es

den Fahrer nicht behindert und den Beifahrer bei

plötzlichem Bremsen nicht verletzen kann.

• ÜDer Halbleiterlaser wird bei berhitzung

beschädigt, bauen Sie das Gerät daher nicht an

einer Stelle ein, wo es heiß wird, z.B. nahe einer

Heizungsauslassöffnung.

•Wenn der Einbauwinkel mehr als 60º von der

Horizontalen abweicht, kann es sein, dass das

Gerät nicht optimal arbeitet. (Abb. 1)

Einbau mit der Gummibuchse

(Abb. 2)

1. Armaturenbrett

2. Halter

Den Halter in das Armaturenbrett einsetzen, dann

die der Dicke des Armaturenbretts entsprechen-

den Zungen auswählen und diese biegen.

(Mithilfe der Ans tze, oben und unten, so festä

wie m glich einsetzen. Zur Sicherung werden dieö

Ansätze 90 Grad gebogen.)

3. Gummibuchse

4. Schraube

Entnahme des Ger tes (Abb. 3)ä

5. Die mitgelieferten Ausziehschlüssel wie in der

Abbildung gezeigt bis zur Einrastposition in das

Gerät einsetzen. Die Schlüssel gegen die Seiten

des Ger ts drä ücken und das Gerät herausziehen.

Befestigungsschrauben f r dieü

Frontplatte (Abb. 4)

6. Befestigungsschraube

Wenn Sie die Funktion zum Abnehmen und

Anbringen der Frontplatte nicht verwenden

wollen, so fixieren Sie die Frontplatte mit den

mitgelieferten Befestigungsschrauben an diesem

Ger t.ä

Einbau <DEUTSCH>

Note:

•This unit is for vehicles with a 12-volt battery

and negative grounding. Before installing it in a

recreational vehicle, truck, or bus, check the bat-

tery voltage.

•To avoid shorts in the electrical system, be sure

to disconnect the ≠battery cable before begin-

ning installation.

• ’Refer to the owner s manual for details on con-

necting the power amp and other units, then

make connections correctly.

•Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

•Route and secure all wiring so it cannot touch

any moving parts, such as the gear shift, hand-

brake and seat rails. Do not route wiring in

places that get hot, such as near the heater outlet.

If the insulation of the wiring melts or gets torn,

there is a danger of the wiring short-circuiting to

the vehicle body.

• ’Don t pass the yellow lead through a hole into

the engine compartment to connect to the battery.

This will damage the lead insulation and cause a

very dangerous short.

•Do not shorten any leads. If you do, the protec-

tion circuit may fail to work when it should.

•Never feed power to other equipment by cutting

the insulation of the power supply lead of the

unit and tapping into the lead. The current capac-

ity of the lead will be exceeded, causing over-

heating.

•When replacing fuse, be sure to use only fuse of

the rating prescribed on this product.

•Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded

or the left and right ≠speaker leads are com-

mon.

•Speakers connected to this unit must be high-

power types with minimum rating of 45W and

impedance of 4 to 8 ohms. Connecting speakers

with output and/or impedance values other than

those noted here may result in the speakers

catching fire, emitting smoke or becoming dam-

aged.

• ’When this product s source is switched ON, a

control signal is output through the blue/white

lead. Connect to an external power amp’s system

remote control or the car’s Auto-antenna relay

control terminal (max. 300 mA 12 V DC). If the

car features a glass antenna, connect to the anten-

na booster power supply terminal.

•When an external power amp is being used with

this system, be sure not to connect the blue/white

lead to the amp’s power terminal. Likewise, do

not connect the blue/white lead to the power ter-

minal of the auto-antenna. Such connection could

cause excessive current drain and malfunction.

•To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the

unused speaker leads without fail. There is a pos-

sibility of short-circuiting if the leads are not

insulated.

•If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition

switch, the red lead of the unit should be con-

nected to a terminal coupled with ignition switch

ON/OFF operations. If this is not done, the vehi-

cle battery may be drained when you are away

from the vehicle for several hours.

•The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

If you ground the products together and the

ground becomes detached, there is a risk of dam-

age to the products or fire.

Connecting the Units

Fig. 5

Abb. 5

Afb. 5

8. Cap (1*)

When not using this terminal,

do not remove the cap.

14. ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to

connect to both connectors.

10. Yellow (2*)

To terminal always supplied

with power regardless of

ignition switch position.

12. Red (4*)

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

9. Yellow (3*)

Back-up

(or accessory)

11.Red (5*)

Accessory

(or back-up)

7. Connect leads of the same

color to each other.

19. Blue/white

To system control terminal of

the power amp (max. 300 mA

12 V DC).

21. Blue/white (7*)

To Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

Note:

Depending on the kind of vehicle, the function

of 3* and 5* may be different. In this case, be

sure to connect 2* to 5* and 4* to 3*.

2. This Product

3. Antenna jack

15. Yellow/black

If you use a cellular telephone, connect it via the

Audio Mute lead on the cellular telephone. If not,

keep the Audio Mute lead free of any connections.

17. Connecting cords with RCA pin plugs

(sold separately)

22. Blue/white (6*)

23. The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and 7*

when Pin 5 is an antenna control type. In another

type of vehicle, never connect 6* and 7*.

1. Rear output

13. Black (ground)

To vehicle (metal) body.

27.

24. Left 25. Right

26. Rear Speaker 26. Rear Speaker

18. Power amp

(sold separately)

20. System remote control

Perform these connections when using

the optional amplifier.

5. Jack for the Wired Remote Control

Please see the Instruction Manual for

the Wired Remote Control

(sold separately).

4. Fuse

16. Speaker leads

White: Front left +

White/black: Front left ≠

Gray: Front right +

Gray/black: Front right ≠

Green: Rear left +

Green/black: Rear left ≠

Violet: Rear right +

Violet/black: Rear right ≠

•Cords for this product and those for other prod-

ucts may be different colors even if they have

the same function. When connecting this prod-

uct to another product, refer to the supplied

manuals of both products and connect cords that

have the same function.

Connecting the Units <ENGLISH>

Connection Diagram (Fig. 5)

1. Rear output

2. This product

3. Antenna jack

4. Fuse

5. Jack for the Wired Remote Control

Please see the Instruction Manual for the Wired

Remote Control (sold sepatately).

6. Note:

Depending on the kind of vehicle, the function of

3* and 5* may be different. In this case, be sure

to connect 2* to 5* and 4* to 3*.

7. Connect leads of the same color to each other.

8. Cap (1*)

When not using this terminal, do not remove the

cap.

9. Yellow (3*)

Back-up (or accessory)

10. Yellow (2*)

To terminal always supplied with power regard-

less of ignition switch position.

11. Red (5*)

Accessory (or back-up)

12. Red (4*)

To electric terminal controlled by ignition switch

(12 V DC) ON/OFF.

13. Black (ground)

To vehicle (metal) body.

14. ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to connect

to both connectors.

15. Yellow/black

If you use a cellular telephone, connect it via the

Audio Mute lead on the cellular telephone. If not,

keep the Audio Mute lead free of any connec-

tions.

16. Speaker leads

White : Front left +

White/black : Front left ≠

Gray : Front right +

Gray/black : Front right ≠

Green : Rear left +

Green/black : Rear left ≠

Violet : Rear right +

Violet/black : Rear right ≠

17. Connecting cords with RCA pin plugs (sold

separately)

18. Power amp (sold separately)

19. Blue/white

To system control terminal of the power amp

(max. 300 mA 12 V DC).

20. System remote control

21. Blue/white (7*)

To Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

22. Blue/white (6*)

23.The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and

7* when Pin 5 is an antenna control type. In

another type of vehicle, never connect 6* and 7*.

24. Left

25. Right

26. Rear Speaker

27. Perform these connections when using the

optional amplifier.

ACC position

No ACC position

Product specificaties

Merk:	Pioneer
Categorie:	Autoradio
Model:	deh-1600r

Heb je hulp nodig?

Als je hulp nodig hebt met Pioneer deh-1600r stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Autoradio Pioneer

Pioneer MVH-S23BT Handleiding

5 November 2024

Pioneer SPH-PF97BT Handleiding

1 November 2024

Pioneer DEH-X6900BT Handleiding

30 September 2024

Pioneer AVH-120BT Handleiding

29 September 2024

Pioneer DEH-S1000UB Handleiding

29 September 2024

Pioneer DEH-S4100BT Handleiding

29 September 2024

Pioneer AVH-1330NEX Handleiding

29 September 2024

Pioneer AVH-1300NEX Handleiding

29 September 2024

Pioneer DMH-160BT II Handleiding

29 September 2024

Pioneer MVH-S21BT Handleiding

29 September 2024

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio

Boss BCPA12 Handleiding

30 November 2024

Alpine mrp m 200 Handleiding

16 November 2024

Panasonic CQ-5250T Handleiding

23 November 2024

Deaf Bonce Machete MFA-1.1500 Handleiding

20 November 2024

Xblitz RF100 Handleiding

15 November 2024

Xblitz RF300 Handleiding

15 November 2024

Xblitz RF500 CAM Handleiding

15 November 2024

Xblitz RF350 CAM Handleiding

15 November 2024

Blaupunkt Alicante CD30 Handleiding

15 November 2024

JBL Grand Touring GTR-102 Handleiding

15 November 2024