Pelco Sarix Professional IBP521-1I Handleiding

Pelco Bewakingscamera Sarix Professional IBP521-1I

Lees hieronder de 📖 handleiding in het Nederlandse voor Pelco Sarix Professional IBP521-1I (69 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/69

C2296M-B-EN (12/ ) 16

Sarix® Professional IBP

Series Environmental IR

Bullet & Indoor Bullet

Camera

User Manual

IBP122- 1I

IBP2 - 22 1I

IBP3 - 22 1I

IBP - 124 1I

IBP - 224 1I

IBP - 324 1I

IBP121- 1I

IBP221- 1I

IBP - 321 1I

IBP - 521 1I

IBP122-1R

IBP2 -1R 22

IBP3 -1R 22

IBP -1R 124

IBP224-1R

IBP324-1R

IBP121-1R

IBP221-1R

IBP -1R 321

IBP -1R 521

Contents

Important Notices Statement ........................................................................................................................................................ 4

Regulatory Notices 4..............................................................................................................................................................

Radio and Television Interference ....................................................................................................................................... 4

Korean Class A EMC 4..................................................................................................................................................

Warranty Statement ..................................................................................................................................................................... 4

UL Safety Notices ................................................................................................................................................................ 4

Preface ......................................................................................................................................................................................... 5

1. Product Overview .............................................................................................................................................................. 6

1.1 Dimensions .................................................................................................................................................................... 6

1.2 Models Introduction 8.......................................................................................................................................................

1.3 Physical Characteristics ................................................................................................................................................. 9

2. Installation and Connection ........................................................................................................................................ 11

2.1 Unpacking Everything .................................................................................................................................................. 11

2.2 Optional Accessories ................................................................................................................................................... 11

2.3 Installation .................................................................................................................................................................... 11

2.3.1 Checking Appearance ...................................................................................................................................... 11

2.3.2 Mounting & Wiring ............................................................................................................................................ 12

2.3.3 Applying Rubber Seal Plug ............................................................................................................................... 16

2.3.4 Safety Wire Preparation ................................................................................................................................... 16

2.3.5 Adjusting the Camera Position ......................................................................................................................... 17

2.3.6 Adjusting the Focus .......................................................................................................................................... 18

2.3.7 Adjusting the Protection Shield Hood ............................................................................................................... 18

2.3.8 Network Topology ............................................................................................................................................19

2.3.9 System Requirements ...................................................................................................................................... 20

2.4 Connection ................................................................................................................................................................... 21

2.4.1 Default IP address ............................................................................................................................................ 21

2.4.2 Connecting From a Computer & Viewing Preparation ...................................................................................... 21

3. Administration and Configuration .............................................................................................................................. 23

3.1 Live .............................................................................................................................................................................. 23

3.1.1 Zoom and Focus Controls ................................................................................................................................ 24

3.2 Settings ........................................................................................................................................................................ 24

3.2.1 System ............................................................................................................................................................. 25

3.2.2 Network ............................................................................................................................................................ 28

3.2.3 Imaging ............................................................................................................................................................. 40

3.2.4 A/V Streams ..................................................................................................................................................... 48

3.2.5 Users ................................................................................................................................................................ 54

3.2.6 Events .............................................................................................................................................................. 57

Pelco Troubleshooting Contact Information ...............................................................................................................................68

Preface

This user manual is to be used as a reference for the installation and manipulation of the camera unit including features,

functions, and a detailed explanation of the menu tree.

This manual provides t following information: he

 The main functions and system requirements of the unit, Product Overview:

 Instructions on unit installation and wire connections. Installation and Connection:

 The main menu navigation and controls explanations.Administration and Configuration:

1. Product Overview

1.1 Dimensions

The dimensions of the Sarix Professional 2 Series Environmental IR bullet camera and Indoor bullet camera are depicted

within the Figure 1-1 below.

VALUES PARENTHE ARE INCHES; ALL HERS ARE IN SES OT

CENTIMETERS.

E B E B 9- / 3-10.5 / 3.6- NVIRONMENTAL IR ULLET NVIRONMENTAL IR ULLET – 22MM MM 10MM

E B - NVIRONMENTAL IR ULLET – 12 40MM

1.2 Models Introduction

The physical appearances and installation methods for the models indicated within the list below are similar. Therefore, please

use this manual where we use the example from IBP521-1RS as a reference to apply to all the varied models.

Model

Description

IBP122- 1I

SRX PRO2 IND BULLET POE24V12V 1MP 9-22MM D/N LENS

IBP222- 1I

SRX PRO2 IND BULLET POE24V12V 2MP 9-22MM D/N LENS

IBP322- 1I

SRX PRO2 IND BULLET POE24V12V 3MP 9-22MM D/N LENS

IBP124- 1I

SRX PRO2 IND BULLET POE24V12V 1MP 12-40MM D/N LENS

IBP224- 1I

SRX PRO2 IND BULLET POE24V12V 2MP 12-40MM D/N LENS

IBP324- 1I

SRX PRO2 IND BULLET POE24V12V 3MP 12-40MM D/N LENS

IBP121- 1I

SRX PRO2 IND BULLET POE24V12V 1MP 3-10MM D/N LENS

IBP221- 1I

SRX PRO2 IND BULLET POE24V12V 2MP 3-10MM D/N LENS

IBP321- 1I

SRX PRO2 IND BULLET POE24V12V 3MP 3-10MM D/N LENS

IBP521- 1I

SRX PRO2 IND BULLET POE24V12 5MP 3-10MM D/N LENS V

IBP122- 1R

SRX PRO2 ENV BULLET POE24V12V 1MP 9-22MM D/N LENS

IBP222- 1R

SRX PRO2 ENV BULLET POE24V12V 2MP 9-22MM D/N LENS

IBP322- 1R

SRX PRO2 ENV BULLET POE24V12V 3MP 9-22MM D/N LENS

IBP124- 1R

SRX PRO2 ENV BULLET POE24V12V 1MP 12- M D/N LENS 40M

IBP224- 1R

SRX PRO2 ENV BULLET POE24V12V 2MP 12-40MM D/N LENS

IBP324- 1R

SRX PRO2 ENV BULLET POE24V12V 3MP 12-40MM D/N LENS

IBP121- 1R

SRX PRO2 ENV BULLET POE24V12V 1MP 3-10MM D/N LENS

IBP221- 1R

SRX PRO2 ENV BULLET POE24V12V 2MP 3-10MM D/N LENS

IBP321- 1R

SRX PRO2 ENV BULLET POE24V12V 3MP 3-10MM D/N LENS

IBP521- 1R

SRX PRO2 ENV BULLET POE24V12V 5MP 3-10MM D/N LENS

T 1-1: M LABLE ODELS IST

F 1-3: C C F 2 IGURE AMERA ONNECTIONS AND EATURES /2

1. Insert a micro SD card to the slot for recording and storage.Micro SD Card Slot (Micro SD):

2. Reset Button (R): Using a small tool, such as a paper clip, hold down the reset button within 5 seconds and release

to restart the camera.

3. Default (DEFAULT): Using a small tool, such as a paper clip, hold down the reset button longer than 5 seconds to

reset the camera to factory defaults.

4. ot a The port in the middle has already connected to a POE cable. The Ethernet/PoE: her end of the cable is RJ-45

Network Port . Connects the camera to the IP network and the LED indicators will light on.

5. Action (ACT) & Link (LINK): LED indicators The LED indicators show the status as the list below:.

Color

Status

Indication

Green

Network connection is established.

Off

No network connection.

Orange

Blinking

Networking is active

Collision occurs

Off

Networking is inactive

2. Installation and Connection

2.1 Unpacking Everything

Check all items in the product box inst the order form and the packing slip. In addition to this manual, the items below are aga

included in the product x: bo

 Environmental IR Bullet camera / Indoor Bullet camera * 1

 Plastic Anchor 4 *

 Flat Head Screw (Tapping Type) 4 *

 Rubber Seal Plug * 1

 T20 Security Torx Wrench * 1

 T Security Torx Wrench * 1 10

 Mounting Template 1 *

 Important Notices Declaration * 1

 Printed Quick Start Guide * 1

 Supplemental Resources Sheet * 1

 Important Safety Instruction * 1

 ROHS Statement Slip * 1

Please contact your dealer if any items are missing.

2.2 Optional Accessories

 IBP2BBAP-ES: Sarix Environmental Surface mount for Bullet a

 IBP2BBAP- : a Sarix Environmental In-Ceiling Mount for Bullet EI

2.3 Installation

Following tools might help you complete the installation:

 A drill

 Screwdrivers

 Wire cutters

2.3.1 Checking Appearance

Although the protective materials used for the packaging should be able to protect the unit from most accidents during

transportation, check the unit and its accessories for any visible damage. Remove the protective film to check items in

accordance with the list . in 2.1 Unpacking Everything

2.3.2 Mounting & Wiring

2.3.3 Surface Installation - Ceiling or Wall .1

Step 1. Mounting Preparation

1. Place the supplied mounting template on a mounting surface. Drill 6 mm (0.25 outer holes at the T1 or T2 template ”)

positions on the mounting surface. Then insert 4 or 2 supplied plastic anchors into the holes. (T1: for double-gang socket,

T2: for single-gang socket, if applicable on mounting surface)

2. Please then hammer the corresponding plastic anchors (4 or 2) into the drilled holes on the mounting surface.

F 2 - 1: M T IGURE OUNTING EMPLATE

Step 2. Mounting the Camera

1. Position the camera to match the drilled holes embedded with the plastic anchors on the surface.

2. Secure the corresponding tapping screws (4 or 2) to fasten the camera with the mounting surface tightly.

F 2 - 2: M C IGURE OUNTING THE AMERA

This section is the preserved

area for cable entry space.

Tapping Screws

Plastic Anchors

With IBP2BBAP- ES

Also, you can mount the camera to the wall with for Bullet. Refer to IBP2BBAP-ES, a Sarix Environmental Surface Mount

the figure below for surface installation with IBP2BB- ES.

1. Fix the IBP2BB -ES back box (#1) to the desirable surface by drilling three holes and fastening it with screws. AP

2. Pass all the signal cables through the hole of rubber (#5), and then insert the rubber into the center hole of metal plate.

NOTE: Please identify both sides of the rubber. The side of the rubber with the inclined angle must be towards the

terminals of the cables and metal plate to avoid water leakage.

3. Install the adaptor plate(#2) in the back box and tighten the screws

4. Insert screws (#4) through the bracket’s screw holes and tighten screws into the corresponding hole (#3) of the adaptor

metal.

5. Complete surface installation with IBP2BB - AP ES.

F 2-5: S M IBP2BB - IGURE URFACE OUNT WITH AP ES

2.3.3.2 -Ceiling Installation In

The is mounting the camera into the ceiling with , a In-Ceiling Installation IBP2BB -AP EI Sarix Environmental In-Ceiling

Mount -ceiling installation IBP2BB - for Bullet. Refer to the figure below for in with AP EI.

1. Make a round hole for IBP2BB -EI back box to fit in. AP

2. Pass all the signal cables through the hole of rubber (#5), and then insert the rubber into the center hole of metal

plate.

NOTE: Please identify both sides of the rubber. The side of the rubber with the inclined angle must be towards

the terminals of the cables and metal plate to avoid water leakage.

3. Install the adaptor plate(#2) in the back box and tighten the screws

4. Insert screws (#4) through the bracket’s screw holes and tighten screws into the corresponding hole (#3) of the

adaptor metal.

5. Complete in-ceiling installation with IBP2BB -EI. AP

F 2- I -C I IBP2BBAP-IGURE 6: N EILING NSTALLATION WITH EI

2.3.3 Applying Rubber Seal Plug

For the scenario of cable thread through mounting hole, it is required to properly secure the rubber seal plug into the side hold

of bracket. The rubber seal plug, with anti-ingress functionality, is able to prevent liquid, e.g., rain, from invading into the

camera and thereby securely assures the stable operation of camera.

F 2 - 7: R S P A IGURE UBBER EAL LUG PPLYING

NOTE: While installing, tuck the rubber seal plug into the side hole from the rear side of the bracket as the image shown

above, so that the complete anti-ingress functionality can be positively guaranteed.

2.3.4 Safety Wire Preparation

If you possess a safety wire (fall prevention wire, not supplied) onnect the safety wire with one end to the mounting surface , c

and the other end to the safety-cord screw of the camera.

F 2 - 7: S C I IGURE AFETY ORD NDICATION

NOTE: Depending on the material of mounting surface, different screws and anchors than those supplied may be required. To

prevent the camera from falling off, ensure that it is mounted to a firm place using a safety wire strong enough to withstand the

total weight of the camera. (Pay also attention to the finishing at the ends of the wire.)

Safety Wire

Safety Cord Screw

Rubber Seal Plug

Side Hold of Bracket

2.3.5 Adjusting the Camera Position

 Retaining Ring for Pan Adjustment (A)

Loosen the locking screw by T20 torx wrench and rotate the retaining ring (A) to adjust the camera horizontally for

applying to a variety of applications.

 Bracket Axis for Tilt Adjustment (B)

Loosen the locking screw by T20 torx wrench and tilt the bracket axis (B) to adjust the camera vertically for applying to

varied applications.

 Adjustable Ring for 360 Rotation (C) °

Loosen the locking screw by T20 torx wrench and rotate the camera body (C) to adjust the camera for applying to varied

applications.

F 2 - 8: A C P IGURE DJUSTING THE AMERA OSITION

NOTE: After adjustments, make sure to tighten each part to prevent camera from moving.

NOTE: Limitation for 3 axes position: Pan range: 360 , Tilt range 0 , Rotation range: . ± ° : °～ 90° ±360°

2.3.6 Adjusting the Focus

1. page View the camera image using the browser (refer to 2.4 Connection 21).

2. e the settings in the Web interface (refer to on page ) to adjust the zoom and focus of the lens to the Us 3.2.3.4 Focus 45

desired field of view.

3. Also the focus can be adjusted by moving the zoom slider and using the Focus options in the live webpage.

NOTE: Focus adjustment is done exclusively with Web UI.

2.3.7 Adjusting the Protection Shield Hood

Environmental IR Series Exclusive Only

The environmental IR series are designed with capability to operate under rugged environments and therefore may subject be

to influences from sunlight or rain. Protection shield hood is therefore coated on the camera prevent damage from those to

outside effects. To adjust the protection shield hood, Move the hood forward backward to adjust till the desired position or

based on your different applications.

F 2 - 9: A P S H IGURE DJUSTING THE ROTECTION HIELD OOD

NOTE: Be sure to adjust the protection shield hood in accordance with the lens coverage in case of shadow problems

occurring. To avoid housing damage, DO NOT adjust the protection shield hood position excessively.

2.3.9 System Requirements

The table below lists the minimum requirement to implement and operate a unit. Network and processor bandwidth limitations

might cause the video stream to pause or appear pixilated when additional Web-interface users connect to the camera.

Decrease the images per second (ips), resolution, compression, or bit rate settings of the Web interface video streams to

compensate for network/processor limitations.

T 2- S R ABLE 1: YSTEM EQUIREMENTS

System Hardware

CPU

Intel® Pentium® 4 microprocessor, 2.4GHz or equivalent

RAM

1 GB or above

Monitor

Minimum of 1024 x 768 resolution, 16- or 32-bit pixel color resolution

System Software

Operating System

Microsoft Windows XP, Vista 32 and 64 bit, Win7 32 and 64 bit

Browser

Microsoft IE 9.0 and later

M Player edia

Pelco Media Player or QuickTime® 7.6.5 for Windows XP, Windows Vista, and Windows 7; or

QuickTime 7.6.4 for Mac OS X 10.4 (or later)

Unit

Power Supply

PoE / AC 24V / DC 12V

Note

1. All the installation and operations should comply with your local electricity safety rules.

2. Pelco Media Player is recommended for control, smoothness, and reduced latency as compared to

QuickTime. The PMP is downloadable from Pelco web site www.pelco.com/mediaplayer. :

3. This product is not compatible with QuickTime version 7.6.4 for Windows XP or Windows Vista. If

you have this version installed on your PC, you will need to upgrade to QuickTime version 7.6.5.

4. Network and processor bandwidth limitations might cause the video stream to pause or appear

pixelated when additional Web-interface users connect to the camera. Decrease the images per

second (ips), resolution, compression, or bit rate settings of the Web interface video streams to

compensate for network or processor limitations.

2.4 Connecti on

2.4.1 Default IP address

The default IP address is and sub mask is . When setting default IP address of 192.168.0.20 unit’s 192.168.0.20 255.255.255.0

the camera will check to see if that address is already in use and will bump the last octet of the address by 1 if it is. The bump

last octet of IP Address by 1 will continue until an unused IP address is found.

However, if you have a DHCP server in your network, the unit would obtain an IP address automatically from the DHCP server

so that y . The factory default is DHCP 192.168.0.20 assignment only ou don’t need to change the camera’s IP address On and

occurs when camera is set for DHCP but a DHCP server does not respond to request for an IP address.

2.4.2 Connecting From a Computer & Viewing Preparation

2.4.2.1 ing Pelco Device Utility Software to Get Camera s IP Address Us ’

Pelco Device Utility software is a utility program that helps users t manage and configure the camera. Use the utility to find o

the IP address since the default option is to obtain an IP address via DHCP and therefore the IP address will NOT be known.

Steps to get the utility program running are listed below.

1. Finish installing the Device Utility to the computer according to the installation instructions.

2. Log in to the Device Utility by entering the camera s User name and Password. In the window, enter the default user ’

name: and password: , then click button to log in. admin admin Enter

3. In the Manage Devices page, you can click Refresh Device List or Add New Device to search for the devices.

4. From the Device List, you can get series information about camera, IP Address included.

For more information about using the Device Utility, click this green icon " " on the upper-right corner of the Device Utility

page.

2.4.2.2 Connecting from a computer

1. Check if there is networking available between the unit and the computer by executing ping the default IP address Start .

a co and prompt (Windows: from the Start Menu, select Program. Select Accessories and choose Co and mm mm

Prompt.), and t 2 available. ype “Ping 192.168.0. 0”. If the message “Reply from…” appears, it means the connection is

2. Start Internet Explorer and enter IP address: . A login window should pop up In the window, enter the 192.168.0.20 .

default user name: and password: to log in. admin admin

NOTE: If you do not know the camera’s IP address, you can locate it using the Pelco Device Utility software (refer to 2.4.2.1

Using Pelco Device Utility Software to Get Camera’s IP Address).

Further administration on the unit can be found in Administration and Configuration “3. ".

F 2- : L WIGURE 11 OGIN INDOW

2.4.2.3 Viewing Preparation

Images of the unit can be viewed through Microsoft Internet Explorer 9 or later. Before viewing, follow these steps to enable

the display.

1. Enable Cookies On the tab, move the settings slider to or . Privacy Low Accept All Cookies

2. Change Security in and click to open the Internet options Custom Level Security Settings Internet Zone – screen.

NOTE: Intranet If the camera operates inside the intranet, click the of icon. If the camera operates outside of the intranet,

click the icon. Internet

3. Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:



 【

【

【【】

】

】】Download signed ActiveX controls  Prompt (recommended)



 【

【

【【】

】

】】Download unsigned ActiveX controls  Prompt



 【

【

【【】

】

】】Automatic prompting for ActiveX controls 



 Enable



 【

【

【【】

】

】】Run ActiveX controls and plug-ins  Enable



 【

【

【【】

】

】】Script ActiveX controls marked safe for scripting*  Enable

4. Press to save the settings. OK

5. Close all Microsoft Internet Explorer Windows and restart a new window. This will allow the new settings taking effect.

6. Type your setting IP address into the browser.

7. en. Then you should be able to see the camera image scre

3.1.1 Zoom and Focus Controls

Zoom

 Zoom In: Click and drag the slider rightward to zoom the lens in.

 Zoom Out: Click and drag the slider leftward to zoom the lens out.

Focus

 Full Range Auto-Focus: Click the button for the camera to start a full-range search to find the optimal focal point for

the scene.

 Quick Auto-Focus: Click the button for the camera to start a quick search to find the optimal focal point for the scene

NOTE: The zoom and focus controls, if available on your model, are viewable only after you have logged on to the device.

3.2 Settings

Click on , a window will pop for configuring Settings up “ ”, “ ”System Network , “ ”Imaging , “ ”A/V Streams , “ ”Users , and

“ ”Events .

F 3-2: S S IGURE YSTEM ETTINGS

3.2.1 System

Use the System tab to change the device name, configure the time settings, set up the text overlay for the live view, get

backup, display system information and update firmware version. You can also use the System tab to generate a system log,

reboot the camera, or to restore the camera's factory default settings.

F 3-3: S S IGURE YSTEM ETTINGS

Generate System L og

1. Click the System tab.

2. Click the Generate System Log button to create a system log that can be used by Pelco Product Support for

troubleshooting.

Contact Pelco Product Support at 1- -289-9100 (USA and Canada) or +1-559- -1981 (international). 800 292

Reboot Camera

1. Click the System tab.

2. Click the Reboot Camera button to restart the camera. Rebooting the camera does not change the configured

camera settings.

Restore All Camera Defaults

This process cannot be undone; all user and custom settings will be lost.

1. Click the System tab.

2. Click the Restore All Camera Defaults button to restore the camera’s factory default settings.

NOTE: If the camera is not connected to a Dynamic Host Configuration Protocol (DHCP) network, the IP address

settings for the camera will be lost and the server will not recognize the camera. DHCP On is the default setting for the

camera IP address.

3. Select the format in which the date and time will appear from the Display Format drop-down field if you have opted

to show the Date/Time Overlay.

4. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

Text Overlay

1. Configure the text overlay settings:

 Set the background color for the text overlay as black or transparent. Text color for the Background:

transparent background can be also customized from the drop-down menu when the transparent background

option is selected.

 Four ntent options can be selected to display from the drop-down menu: Date/Time, Camera Content: co

Name, Camera Name + Date/Time, and Custom Text. The blank text field, which is for inputting desired text

by users, shows only when Custom Text option is selected.

NOTE: Multiple content options can display simultaneously.

 Four positions can be selected to display content overlays: Top Left, Top Right, Bottom Content Position:

Left, and Bottom Right. For Bottom Right position, a note that informs that a maximum of five lines with

commas to switch between them would appear under the text field once Custom Text option is selected.

NOTE: A maximum of 3 content positions can be displayed simultaneously.

2. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

3.2.1.2 Backup & Restore

F 3-5: B R S IGURE ACKUP AND ESTORE ETTINGS

Backup

Once the camera settings have been configured for optimal scene display, use the backup feature to save the camera

settings.

Restore

If the camera settings are changed and inadvertently result in a less desirable image, use the restore setting to restore the

camera to the previously saved settings.

NOTE: This feature is not intended for the configuration of multiple units or for firmware upgrades.

3.2.2.1 General

Set the General Network Settings for network communication settings.

F 3-9: G N S IGURE ENERAL ETWORK ETTINGS

System Settings

Settings under the System Settings are Hostname, HTTP Port, HTTPS Port, and RTSP Port. Contact your network

administrator before changing port settings to ensure that your port settings do not conflict with your network infrastructure.

 Hostname

1. Click in the box and highlight the text.Hostname

2. Type a user-friendly name into the Hostname box (1 to 21 characters) using any combination of alphanumeric

characters. A user-friendly name makes it easier to recognize the device on the network.

3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

 HTTP Port

NOTE: The HTTP port number must remain at the default setting (80) when connecting to a Pelco video management

system (VMS) platform. If connecting to a Pelco VMS, do not change the HTTP port setting.

1. Click in the box and highlight the text. HTTP Port

2. Type the new port number in the field. The default port for HTTP communications is . HTTP Port 80

3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

 HTTPS Port

NOTE: The HTTPS port is not configurable unless you have set SSL Mode to Optional or Required and installed a

security certificate.

1. Click in the box and highlight the text. HTTPS Port

2. Type the new port number in the field. The default port for HTTPS communications is . HTTPS Port 443

3. Click Save. If you have changed the setting in error, you can click reset to revert to the previously saved setting.

 RTSP Port

1. Click in the box and highlight the text. RTSP Port

2. Type the new port number in the field. The default port for RTSP communications is . RTSP Port 554

3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

IPv4 Settings

Enable or disable the server. DHCP automatically assigns an IP address to Dynamic Host Configuration Protocol (DHCP)

the device if there is a DHCP server on the networ k.

 the IP address, subnet mask, gateway, and DNS server settings are read-only text. If DHCP is set to On,

 these settings must be manually changed. If DHCP is set to Off,

Change the following network settings as required:

1. The address of the camera connected to the network. IP Address:

2. The address that determines the IP network that the camera is connected to (relative to its Subnet Mask:

address).

3. The router that accesses other networks. Gateway:

4. The addresses of the dedicated servers that translate the names for Web sites and hostnames into DNS Servers:

numeric IP addresses.

5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

Configuring IPv6 Settings

Your Sarix device supports IPv6 in conjunction with IPv4 configurations; the device does not support IPv6-only network

deployments. The device will accept up to sixteen IPv6 addresses, three IPv6 DNS servers, and three IPv6 gateways.

There are two configuration modes for IPv6 address assignments:

Auto: Enables automatic configuration using router advertisement. Additional configuration can be provided over DHCPv6 (if

available on your network). Selecting Auto mode still allows you to manually configure additional IPv6 addresses, DNS servers,

and gateways.

Manual Only: Provides a link-local IPv6 address for the device and allows you to assign up to 16 static IPv6 addresses to the

device.

1. Place your mouse pointer over the Network tab.

2. Select General from the drop-down menu.

3. Select On for IPv6.

4. Select a Configuration Mode from the drop-down box. Selecting Auto allows the device to configure the remaining IPv6

settings automatically, rendering the remaining steps optional.

5. (Optional) Provide static, unicast addresses in the Manual IP Addresses box. Each address requires a prefix, and it must be

input using the format prefix/IPv6Address. Manual IP addresses without prefix information will be rejected.

6. (Optional) Provide the addresses of DNS servers that are not configured automatically in the Manual DNS Servers box.

7. (Optional) Provide the addresses of gateways that are not configured automatically in the Manual Gateways box.

NOTES:

• The device will not accept multicast, localhost, or undefined IPv6 addresses.

• Link-local addresses are not supported for DNS.

• Manually specified DNS servers supersede automatically discovered DNS servers.

• Manually specified DNS servers are not validated by the device; verify any manually specified DNS servers before saving

IPv6 settings.

• Manually specified gateways must be on the same network as the devices’s IPv6 addresses. Behavior for a gateway that is

not on the same network as the device’s IPv6 addresses is undefined.

• Some video management systems (VMS), including Pelco VMS systems, do not support connections to cameras and

encoders over IPv6.

3.2.2.2 SSL

To ensure security on the Internet, all Web browsers provide several security levels that can be adjusted for sites that use SSL

technology to transmit data. encrypts communications, making it difficult for unauthorized users to intercept and view user SSL

names and passwords.

SSL requires signed certificates to determine if the Web browser accessing the camera has the required authentication. The

camera can generate a certificate signing request (CSR) that can be sent to a certificate authority for a signature (for example,

VeriSign® ), or it can generate a self-signed certificate using the option. Generate Self-Signed Certificate

F 3- : C IGURE 10 SSL ONFIGURATION

SSL Configuration

Select one of the following modes:

 A signed Secure Sockets Layer (SSL) certificate must be installed, and a secure URL that begins with the Required:

protocol name “https:” must be used to access the camera. Sensitive data is always encrypted during transmission. A

URL that begins with the “http:” protocol rather than the “https:” protocol will be redirected to the secure URL

automatically.

NOTE: Beginning with firmware version 1.8.2, this field cannot be modified in the Web browser. To select or clear the

Required mode, you must use the ONVIF or Pelco API call. Doing so avoids placing the camera into a mode in which it

would no longer work with a connected VMS system.

 A signed SSL certificate must be installed, but a secure URL that begins witOptional: h the protocol name “https:” is

optional when accessing the camera. You can also access the camera using a standard URL with the “http:” protocol, but

sensitive data is not encrypted during transmission. To ensure that sensitive data is encrypted, you must use a secure

URL with the “https:” protocol.

 Turns off access to the Web client through SSL. Sensitive data will not be encrypted during Disabled (default):

transmission.

NOTE: If the SSL mode is set to disabled, you cannot access the camera using a URL that begins with an “https:”

protocol. Your Web browser displays an error message if you do not type the camera URL correctly.

Refer to the following sections for more information:

• Generating Self-Signed Certificate

• Generating Certificate Request

Certificate

 Generating Self-Signed Certificate

1. Click the button located at the bottom of the Configuration page. The Select Install New Certificate SSL

Certificate Install Method option buttons appear on the page.

F 3-11: S C I M IGURE ELECT ERTIFICATE NSTALL ETHOD OPTION

 Upload Certificate

1. Click the button located at the bottom of the SSL Configuration page. The Select Certificate Install New Certificate

Install Method option buttons appear on the page.

2. Select , and then click Upload Certificate Next Certificate. The “ ” opens.

F 3-14: U C IGURE PLOAD ERTIFICATE

3. Choose the Certificate you want to upload and then click button. The following progress message appears Upload

on the page: “ …” Loading data

4. ter the certificate is uploaded, select the desired mode. Af

5. Click Save.

 Delete Certificate

1. Once you successfully upload a certificate, button will appear at the bottom of the SSL Delete Certificate

Configuration page.

2. If you want to delete the certificate, click the the following progress message appears on the Delete Certificate,

page: “ …” Deleting certificate file

3. Click Save.

3.2.2.3 SSH

SSH is a user-enabled protocol that allows Pelco Product Support to log on to and service the camera for advanced

troubleshooting purposes.

From this page, users with the appropriate permissions can enable or disable SSH access to the camera.

F 3- : E S S IGURE 15 NABLING ECURE HELL

SSH Settings

1. Select the check box. Enabled

2. Click in the box and type a password (4 to 16 alphanumeric characters). Passwords are case-sensitive. Password

NOTE: The default username is “root” and cannot be changed. The username and password are required when

accessing the camera through a third-party SSH client.

3. nd retype your password. Click in the “ ” box aRe-type Password

4. Click the Save button to save the password and enable SSH, or click the Reset button to clear all of the information

you entered without saving it.

SNMP Configuration

WARNING: The Simple Network Management Protocol (SNMP) settings are advanced controls. Consult your network

administrator to obtain the required information to configure SNMP settings.

 No SNMP Server

None sables the SNMP configuration and is the default setting.di

 CONFIGURING SNMP V2C

1. Select as the SNMP Version. V2c

2. Type the community name in both the Read and Write Community String box. The default name for each is “public”

and private respectively. “ ”

3. Configure the Trap Configuration settings.

 Type the host name or IP address of the recipient of the trap message. Address:

 Type the name of the community that should receive the trap message. Community String:

4. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

 CONFIGURING SNMP V3

1. Select as the SNMP Version. V3

2. Enter the SNMP user name in the field. SNMP User

3. Select the encryption algorithm for authentication from the drop-down menu: None, MD5, or SHA. Authentication

If you use authentication method MD5 or SHA, type a password in the text box to the right of the selected

Authentication encryption.

4. Select the privacy encryption algorithm setting from the drop-down menu: None, DES, or AES. If you use Privacy

privacy method DES or AES, type a password in the text box to the right of the selected Privacy encryption.

5. Configure the address for the . The Address is the host name or IP address of the recipient of Trap Configuration

the trap message.

6. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

NOTE: SNMP V2c and SNMP V3 configuration settings are independent of each other, but only one SNMP version can

be active at a time.

3.2.2.6 Firewall

Set the function. A firewall is a system or group of systems that manages access between two networks. Firewall

F 3- : F C IGURE 18 IREWALL ONFIGURATION

Firewall

1. Select or mode to enab this function. The default setting is Allow Deny le Off.

2. Check to enter IP address in the field. Up to ten addresses can be enabled for entry.Enabled Address

3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

3.2.2.7 F TP

This page will enable or disable access to this camera. In this page, users can activate a FTP Server to access the SD FTP

card for recordings. the and use this function. Enabled FTP

F 3- : F S IGURE 19 TP ETTINGS

FTP Settings

1. Select the check box to activate the FTP function, and follow the following procedures to set up related Enabled

settings.

2. Enter a if activated the FTP function. Username

3. Enter a associated with the . Password Username

4. Re-type Password to confirm it.

5. Set the number of maximum connections by entering a number in the field. Max Connections

NOTE: This is the maximum of FTP Client connections, not the maximum of IE Window’s connections.

6. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

3.2.2.8 RTP

RTP is a standard protocol for connecting a client to establish and control streaming data over web. If you want to allow 3

party devices or software to access video/audio streams from the IP camera over the network, you must configure the RTP

related settings. Please refer to below and define proper parameters based on your network applications for better efficiency.

F 3- : RTP S IGURE 20 ETTINGS

Multicast

Multicast transmits streams via the way of 1 to multiple devices as opposed to unicast which is based on 1 to 1 device method

and requires large network resources of server; in other words, multicast needs less bandwidth with resources and is more

practical for multiple devices broadcast on condition that all relevant peripheral devices like switch or router support the

multicast protocol.

 Input an RTP IP address into the field of Address and define the relative port number within the Primary Video Stream:

Port field. Also, TTL (Time to Live) can be assigned from 1 to 255 by user. Check the check box of Always Multicast this

stream to enable the function if necessary.

 Refer to the descriptions of primary video stream and set up your own settings specifically. Second Video Stream:

 Refer to the descriptions of primary video stream and set up your own settings specifically. Audio Stream:

NOTE: Click “Restore Default Multicast Settings” to restore back to the factory default settings. Also, click “Revert to

previous Multicast Settings” to discard your current changes and return to the previous settings.

TCP/IP

 Input a digit ranging from 60 through 1500 into the field manually for the designated max. Max. Transfer Unit (MTU):

transfer unit.

NOTE: Click “Restore Default TCP/IP Settings” to restore back to the factory default settings. Also, click “Revert to

previous TCP/IP Settings” to discard your current changes and return to the previous settings.

3.2.2.9 VMS Connectivity

This page relates to the standard protocol that conforms to the regulations of IP security surveillance data transmitting,

transferring and monitoring within the PRC (People Republic of China) areas.

F 3- : VMS C S IGURE 21 ONNECTIVITY ETTINGS

Endura Connectivity

In order to connect with the Pelco NVR Endura, please choose which communication method to be adopted for connectivity

from the following 2 options:

 Listen for Endura SM system availability broadcast: In general, Endura broadcasts its SM IP Address to the camera

so that a stable connection can be maintained between Endura system and the camera.

 Associate with specific Endura SM system: Under certain cases, the camera is unable to receive broadcast from

Endura system and therefore is in need of a SM IP Address assigned specifically by user for connectivity.

GB/T- Settings 28181

1. Select the check box to activate the VMS Connectivity function. Enable

2. Enter an address for and a value for ranging from 1025 65535. Server Address Port –

3. After registering the GB28181 service, enter a and an associated . Device ID Password

4. A set of alarm ID will be obtained after registering the GB28181 service. Input the provided alarm ID, which is for

alarm notice, into the field here.

5. Set an interval value for Heartbeat and Register transmit with the server individually.

3.2.3 Imaging

Use the Imaging tab to change the camera’s general image settings, adjust the camera exposure and white balance, program

the focus mechanism, or define window blanking privacy areas.

F 3-22: I S IGURE MAGING ETTINGS

3.2.3.1 General

General imaging settings include adjustments for camera orientation and digital processing.

F 3-23: G I S IGURE ENERAL MAGING ETTINGS

Orientation

Use this setting when installing the camera in an inverted position. If the orientation is not adjusted, the image will display

upside down and mirrored.

Select one of the following options:

1. Click the “ ” box to rotate the camera image 180 degrees horizontally.Flip left- -rightto

2. Click the “ ” box to rotate the camera image 180 degrees vertically.Flip top- -bottomto

Digital processing

Digital proces noise reduction, sharpness, saturation, contrast, brightness and hue. sing settings can adjust the camera’s

Move the slider to the left or right to change the following settings:

 Enable 3D Noise Reduction to improve video noise in low light scenes. Turn off 3D noise reduction 3D Noise Reduction:

if details are blurred in moving objects.

 Controls the clarity of detail in a scene. Move the slider to the right to increase the sharpness; move the Sharpness:

slider to the left to decrease the sharpness. Increasing the sharpness also increases the image noise. The range of

adjustment is 100 to 100; the default setting is 0 (zero). –

 Controls how intense or vivid the colors are in a scene. Move the slider to the right to increase the saturation Saturation:

level; move the slider to the left to decrease the saturation level. The range of adjustment is 100 to 100; the default –

setting is 0 (zero).

 Controls gradations between the darkest and lightest portions of the scene. Move the slider to the right to Contrast:

increase the contrast; move the slider to the left to decrease the contrast. The range of adjustment is 100 to 100; the –

default setting is 0 (zero).

 Controls the lighting detail in a scene. Move the slider to the right to lighten the image; move the slider to the Brightness:

left to darken the image. The range of adjustment is 100 to 100; the default setting is 0 (zero). –

 Controls the color in a scene. Move the slider to the right to achieve a cool color image; move the slider to the left to Hue:

achieve a warm color image. The range of adjustment is 100 to 100; the default setting is 0 (zero). –

Check box to lock the above Digital processing settings.Lock Settings

3.2.3.2 Exposure

Exposure is the amount of light detected by the camera sensor. A scene with correct exposure settings has adequate detail

and contrast between white and dark values. An image with too little or too much exposure eliminates detail in the scene. The

camera features Exposure and Day/ Night settings.

F 3-24: E S IGURE XPOSURE ETTINGS

Exposure

 Priority Preset

Select or as the exposure priority. The Motion setting increases exposure time to reduce motion Motion Low Noise

blurring in low light. The Low Noise setting decreases exposure time and adjusts frame rate for improved noise reduction

in low light scenes.

 Flicker Correction

Flickering by fluorescent light can be reduced by selecting “50Hz” if the power frequency is 50Hz, “60Hz”, if 60Hz.

Basic Setting

 BLC

Select an area ranging from Upper, Lower, Central 1/3rd, Central 1/6th, Left, and Right for Backlight Compensation.

Backlight Compensation is a function that sets the brightness of a selected area to an optimal level. This function is

necessary when an auto iris lens tends to close quickly due to an intense light coming from the back of object in the area

wished to view, resulting in the area being too dark and difficult to see. In this case, users may set the area

corresponding to the portion they wish to see.

 Digital WDR

Select On to enable Digital WDR. This feature is intended for prov ing clear images even under backlight where intensity id

of illumination can vary excessively, i.e. when both very bright and dark areas simultaneously come in the field of view.

Digital WDR, via software algorithm, enables capture and display of both bright and dark areas in the same frame, in

such a way that there are clear details in both areas, i.e. bright areas are not saturated and dark areas are not too dark.

Day/Night

The Day Night Auto mode setting automatically controls the IR cut filter depending on the Transition Level and Transition

Detect Time settings.

 Auto

1. Determines when the camera changes from day mode (color) to night mode (black-white). Transition Level:

Select the “ ” transition level setting if you want the camera to change modes aLighter t a high lux setting. Use the

“ ” setting for normal day/night operation. Use the “ ” transition level to change modes at a low lux Default Darker

setting.

T 3-1. L T P I L ABLE UX RANSITION OINTS FOR NCANDESCENT IGHTING

Transition Level

Setting

Day to Night

Transition Point

Lighter

10 lux

Default

2 lux

Darker

1 lux

Check box to enable IR Illumination. IR Illumination

NOTE: IR Illumination function is available in IR equipped models only.

2. Transition Detect Time (sec): Controls the length of time the camera is exposed to a light level before it changes

to color or black-white mode.

This setting is useful for dark scenes where a bright light is momentarily introduced in the scene (for example,

when a car with its headlights turned on passes the camera scene).

F 3-25: D S - M IGURE AY/NIGHT ETTINGS ANUAL

 Manual

1. Day: Day If mode selected, the camera is forced to stay in mode all day. Day

2. mode selected, the camera is forced to stay in mode all day. Night: If Night Night

3. mode selected, the camera is forced to stay in Night w/IR Illumination: If Night w/IR Illumination Night w/IR

Illumination IR illumination mode all day with on. A Slider for adjustment to IR Level ranging from 10 (The Lowest)

to 100 (The Highest) appears beneath when mode is selectNight w/IR Illumination ed.

NOTE: IR Illumination function is available in IR equipped models only.

3.2.3.3 White Balance

Under , choose from (auto tracing white balance), , and modes of adjustment on white White Balance ATW Auto Manual

balance for the video. enables automatic controls color temperature rang from 00°K to 00°K.ATW on ing 25 100 Auto offers

continuous adjustments camera color balance in accordance with any change in color temperature. on

F 3-26: W B S IGURE HITE ALANCE ETTINGS

Under mode, the Red and Blue Gain adjustment bars with their scale boxes on their right will appear once the mode is Manual

selected. Base color of the video will change as the bars are adjusted left or right. Adjust to the ideal balance as appear fit.

Click on to have the camera adjust to the proper gain values rapidly depending on the ambient environment of area One Push

viewed, where its light source is constant, without adjusting for any change in light source or color temperature.

F 3-27: W B S - MIGURE HITE ALANCE ETTINGS ANUAL

3.2.3.4 Focus

Focus sets the back focus to the center focal point of the scene. The camera can be configured to back focus automatically or

manually. Auto focus automatically back focuses the camera on the subject in the center of the scene. Manual focus turns off

the auto focus mechanism and locks the camera at a user-specified position. The manual focus setting is recommended only

for indoor applications that have a single, unchanging primary light source. The Focus page also includes Full Range

Auto-Focus Quick Auto- Restore Settings to Defaults, Focus, and a .

F 3-28: F S IGURE OCUS ETTINGS

Focus

 Auto Focus

1. The camera is programmed to run a quick automatic focus sequence when the Temperature Change Refocus:

internal temperature sensor of the camera detects an environmental temperature change of 41°F (5°C). This focus

sequence adjusts the center focal point of the scene to maintain optimal focus. The default setting is ; select Off On

to turn this setting. on

2. Day/Night Switch Refocus: The default setting for the Day/Night Switch Refocus is . Select Off On if the camera’s

focal length is greater than 25 mm or the night scene uses mostly IR lighting. The best method to determine if the

day/night refocus should be enabled is to test the camera with the daytime light conditions, and then test it again

with the nighttime light conditions.

When enabled this setting refocuses the camera when the camera changes from day mode (color) to night On

mode (black-white) or vice versa. For example, if the camera changes from day mode to night mode, the imager

automatically adjusts the back focus for the change in light.

3. If required, use one of the following buttons to adjust the focus:

 The camera starts a full-range search to find the optimal focal point for the scene. Full Range Auto-Focus:

 The camera searches for the optimal focal point in a limited range. Quick Auto-Focus:

 The camera resets the auto focus to the factory default setting. Restore Settings to Defaults:

NOTE: Auto Focus function is available motorized models only. in

 Manual Focus

Select Mode. Two sliders will appear, one for , the other for Manual Day Manual Focus Position Night Manual Focus

Position. Each slider will show a value that is the best focus position for the camera during the day and night.

F 3-29: M F S IGURE ANUAL OCUS ETTINGS

1. Day Manual Focus Position: Day Manual Focus If you need to fine-tune the daytime focus, slightly move the

Position slider to the left or right.

2. If you need to fine-tune the nighttime focus, slightly move the Night Manual Focus Position: Night Manual

Focus Position slider to the left or right.

3. If required, click the button to reset the focus to the factory default setting.Restore Settings to Defaults

NOTE: Manual Focus function is available motorized models only.in

Zoom

Manually move the slider to the left or right to zoom in or zoom out the image, adjust the zoom value from 1.00~3.00 to Zoom

get the desired field of view.

NOTE: Zoom function is available in motorized models only.

3.2.3.5 Window Blanking

Window blanking is used to conceal user-defined privacy areas. A blanked area appears on the screen as a solid gray window. The

camera can handle up to 8 blanked windows as long as the total blanked area does not exceed 50 percent of the field of view.

F 3- : W B S IGURE 30 INDOW LANKING ETTINGS

Window Blanking

 Window Blanking On

1. Draw a window in the Live Preview area of the page:

a Hold down the left mouse button.

b Drag the mouse diagonally across the area you want to blank.

c A color-coded box appears in the Edit Window section of the page that is the same color as the window drawn

in the Live Preview area.

F 3- : W B O IGURE 31 INDOW LANKING N

NOTE: Up to 8 blanked windows can be defined, but the blanked area cannot exceed 50 percent of the field of view.

2. To resize the window, click and drag one or more of the points until the window is the desired shape and size.

3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

 Deleting a window blanking area

1. In the Edit Window area of the page, click the Delete button next to the window blanking area you want to delete.

2. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

 Window Blanking Off

1. Select the Off option for Window Blanking.

2. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

3.2.4 A/V Streams

Use the A/V Streams tab to configure the video and audio streams for the camera. The A/V Streams tab includes a Video

Configuration page, an Audio Configuration page, a Local Recording page and a H.264 Advanced Compression page.

F 3-32: A/V S IGURE TREAMS

3.2.4.1 Custom Video Stream Configuration

The Video Configuration page allows you to customize the compression, resolution, image rate, and bit rate of the video

streams. The default names for the streams are Primary Stream and Secondary Stream. Although each stream can be

configured independently, the settings of one stream can limit the options available to the other stream, depending on the

processing power used.

NOTE: Always configure the primary stream before the secondary stream. The primary stream should always be the most

resource-intensive of the streams.

F 3-33: C V S C IGURE USTOM IDEO TREAM ONFIGURATION

Select Preset

Presets are fully-configured video configurations that offer a good balance of video performance to bandwidth. These presets

may also be used as a starting point for a custom configuration. Choose to switch the Corridor Mode On or Off. Corridor Mode

offers a vertical widened field of view in narrow spaces like hallways and tunnels. ly

NOTE: Corridor mode is not available when codec is MJPEG.

Primary Stream

Select Custom in Select Preset and configure Primary Stream.

 Compression Standard

1. A new version of MPEG-4 compression used in high-definition video players such as Blu-ray and HD-DVD. H264: ™

H.264 is the most processor-intensive, but it requires the least amount of bandwidth.

2. A commonly used video compression scheme. MJPEG has the least impact on the camera's processor, MJPEG:

but it requires the most bandwidth.

 Resolution

Refer to the following table for the resolution capabilities of your camera model.

T 3-2. C R / C / S ABLE ORRELATIONS OF ESOLUTIONS OMPRESSIONS TREAMS

Primary Stream

Secondary Stream

Service Stream

Compression

Stand d ar

Available

Resolutions

H264

MJPEG

H264

MJPEG

2592 1944* x

2592x1944

N/A

800x600

640x480

320x240

800x600

640x480

320x240

640x480

2048x1536 **

2048x1536

800x 600

640x480

320x240

800x600

640x480

320x240

640x480

1920x1080 ***

1920x1080

960x540

640x352

1920x1080 ***

1920x1080

640x352

320x180

640x352

320x180

640x352

1280x960

800x600

640x480

320x240

800x600

640x480

320x 240

640x480

1280x720

640x352

320x180

640x352

320x180

640x352

1280x960 ****

1280x960

800x600

640x480

320x240

1280x960

800x600

640x480

320x240

640x480

1280x720 ****

1280x720

640x352

320x180

1280x720

640x 352

320x180

640x352

800x600

640x480

320x240

800x600

640x480

320x240

640x480

320x240

640x480

320x240

640x480

320x240

640x480

320x180

640x352

*NOTE: supports only. 2592 x 1944 5MP Model and MJPEG

** NOTE: 5MP Model 3MP Model 2048x1536 supports and only.

*** NOTE: 5MP Model 3MP Model 2MP Model 1920x1080 supports and and only.

**** NOTE: 1MP Model These resolution combinations are available for only.

 Rate Control

The rate control setting determines the bit rate and quality of each frame in the video stream.

 The constant bit rate (CBR) streams video at a fixed number of bits per second. CBR uses the full capacity of CBR:

the bit rate setting for scenes with or without motion. Video is always streamed at the user bit rate setting.

Adjust the CBR Bit Rate slider that appears when CBR is selected to the optimal fixed number of bits per second.

 The constrained variable bit rate (CVBR) provides high-quality video and long recording time of variable bit CVBR:

rate while limiting variations in recording capacity consumption. Adjust the Maximum Bit Rate slider that appears

when CVBR is selected to the optimal bit rate for your configuration.

 Image Rate

The image rate is the number of images per second (ips) available for the video stream configuration. Available image

rates are 30, 25, 20, 16.67, 15, 12.5, 12, 10, 7.5, 5, 3, 2, and 1.

NOTE: The maximum image rate setting might not be obtainable due to the programmed compression standard and the

resolution of the stream.

 GOP Length

Select the GOP Length from 1 to . The upper limit depends on the selected image rate. Recovery of the lost frames will 60

be more difficult as the value gets bigger. Smaller values will increase the bit rate and network bandwidth demands. This

setting is only available with H264.

 QoS (DSCP) Codepoint

Quality of Service (QoS) for Differentiated Services Code Point (DSCP) is a code that allows the network to prioritize the

transmission of different types of data. This setting is only available with H264.

NOTES:

1. If you are not familiar with DSCP, contact your network administrator before changing this setting.

2. Your network must be configured to use QoS. If you are unsure if your network is QoS-aware, contact your network

administrator.

 Endura Signing

Enabling the Endura Signing feature allows an Endura® system to authenticate video from an Endura recorded stream.

This setting is only available with H264.

 Profile

The profile defines the subset of bit stream features in an H.264 stream, including color reproduction and additional video

compression. It is important that the selected profile is compatible with the recording device so that a stream can be

decoded and viewed.

1. A complex profile with a high compression ratio. This is the primary profile for high-definition television High:

applications; for example this is the profile adopted for Blu-ray and HD-DVD. The high profile supports I-frames,

P-frames, and B-frames.

2. An intermediate profile with a medium compression ratio. Main is the default profile setting. This profile is Main:

compatible with most recorders and uses fewer bits to compress video than the baseline profile; however, it uses

more bits than the high profile. The main profile supports I-frames, P-frames, and B-frames.

3. A fairly basic profile that is almost compatible with an array of applications. Baseline:

Secondary Stream

Select Custom in Select Preset and configure Secondary Stream. Repeat Primary Stream setting steps for the Secondary

Stream settings.

3.2.4.2 Audio Configuration

The Audio Configuration page allows you to setup the audio device. The default setting for Audio is disabled, which means

that no audio is transmitted from the camera. When enabled, audio is transmitted from the camera to the PC. Based on your

system configuration, images and audio may not be synchronized.

NOTE: Improper use of audio/visual recording equipment may subject you to civil and criminal penalties. Applicable laws

regarding the use of such capabilities vary between jurisdictions and may require, among other things, express written consent

from the recorded subjects. You are solely responsible for insuring strict compliance with such laws and for strict adherence to

any/all rights of privacy and personality.

F 3-34: A C IGURE UDIO ONFIGURATION

Audio In

 Enabled

Set to when receiving audio from a microphone plugged into the unit.Enabled

 Disabled

Set to to close . Disabled Audio In

Encoding

Two audio codecs can be chosen from. G711-Alaw/G711-Ulaw

Level

The selectable sound levels are High, Mid, and Low.

NOTE: Changes to these settings cause video to restart.

3.2.4.3 Local Recording

Local Recording enables users to record and save video files locally on the SD card inserted, instead of recording and saving

them over the network that will occupy a huge portion of memory and bandwidth. Check to enable this type of recording. Note

that once the card is full, the oldest and previously-recorded video files on the card will be overwritten when the option “Enable

Continuous Recording” is checked.

F 3-35: L R IGURE OCAL ECORDING

3.2.4.4 H.264 Advanced Compression

The H.264 Advanced Compression features the brilliantly efficient stream compression technology to not only economically

exert leverage between different regions and compression levels, but also effectively reduce the average bit rate to level down

the overall bandwidth exploitation. Refer to the following section for elaborate descriptions.

F 3-36: H.264 AIGURE DVANCED OMPRESSIONC

Smart Compression Level

Smart Compression swiftly identifies dynamic motions occurred within a scene and retains its details with clear quality,

whereas the rest areas, e.g. static background, will be imposed on higher compression level, thus economically decreasing

bandwidth wielding on less important things and still keeping the dynamic motions details for future forensic purpose. The

intensity for Smart Compression can be defined by the different levels options. Select Off will simply disable this function.

Advanced Settings

Enable Dynamic GOP Length: By enabling the Dynamic GOP Length function, the overall bitrate, i.e. bandwidth utilization,

will be reduced progressively. When less motion happens within a scene, e.g. storeroom, I-frame number, which is needed

when motions are in scene, will be cut down largely by Dynamic GOP Length. Note that prior to enabling Dynamic GOP

Length, it is required to make sure if your VMS is compatible with this function; otherwise, unexpected result or failure may

occur when incompatibility happens between Dynamic GOP Length and VMS.

3.2.5 Users

Use the Users tab to create and manage user accounts and to change the way the camera manages the user settings.

F 3-37: U C IGURE SERS ONFIGURATION

3.2.5.1 General Settings

Use the General Settings page to set the public user access level. This access level is a predefined set of user permissions

that allows the camera to be accessed without logging on. Available permission levels depend upon the model of the device

that you are using.

The General Settings page also allows you to change the way the camera manages users and groups settings. These settings

can be managed on a camera- -camera basis or by using a centralized server to apply changes to multiple cameras. to

F 3-38: U G S IGURE SERS ENERAL ETTINGS

Authentication Mode

 Open Authentication

Allows users to view video and use the camera API without validating user credentials. With Open Authentication

selected, you can check “Require password for ” or “Require Password for Live View” or both to limit Stream Selection

privileges to authenticated users.

 Closed Authentication

Requires users to possess valid credentials to view video and access the camera API. Before selecting Closed

Authentication, ensure that your video management system supports Closed Authentication mode.

User and Group Management

Sarix cameras support two methods for managing the permissions of users and groups.

 Local Mode

The camera manages users and groups locally. This is the default setting.

 Remote Mode

The camera authenticates and manages users through an LDAP server supported by Microsoft® Active Directory® . This

allows administrators to tie cameras and group permissions into existing single sign-on services (SSO). Selecting

Remote Mode disables local user management settings.

Enabling Remote Mode

F 3-39: E R M IGURE NABLING EMOTE ODE

Select Remote Mode under User and Group Management.

1. Server settings for remote server

a Type the IP address or hostname of the LDAP server in the box. LDAP Server

b Type the port over which the camera will communicate with the LDAP server in the box. The default AP Port

port for AP Communications is 389.

c Type the distinguished name (DN) that is the basis for LDAP searches in the box. Base DN

d Provide the template to format the username (provided when the user logs on to the camera) for searches in

the LDAP directory in the box. Bind DN Template

e Provide the LDAP search query for users found in the base DN in the box. The search Search Template

must match an entry in the LDAP user record to the bind name (username).

2. Group Mappings for remote server

Input Group Mappings for each of the camera’s four user groups:

a Input the common name (CN) and DN for the group of users to whom you want to grant admin access in the

Admins box.

b Input the CN and DN for the group of users to whom you want to grant manager access in the box.Managers

c Input the CN and DN for the group of users to whom you want to grant operator access in the box.Operators

d Input the CN and DN for the group of users to whom you want to grant viewer access in the box.Viewers

3. A user must be authenticated by the remote server prior to entering remote mode.

In the and boxes, input the credentials of a user who can be authenticated through the LDAP User Password

server.

NOTE: Remote Mode (LDAP authentication) will not be enabled if you leave these fields blank or do not provide valid

credentials; this ensures that you cannot lock yourself out of the camera with invalid or incorrect LDAP settings.

4. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

3.2.5.2 Users

User accounts are created to limit the permissions of individuals who are logged onto the camera. The Users page also

includes four predefined access level settings that include Administrator, Manager, Operator, and Viewer permissions.

F 3- : N U IGURE 40 EW SERS

Creating a New User

Click button below the left box and Select the Access Level for the new user. New User

 Access Level

1. Select the Access Level for the user.

 This is the only defined group that cannot be deleted. This group has access to all permissions. Admins:

 This defined group can be modified or deleted. This group has access to all permissions except Managers:

the permissions of access to Users page and the restore factory defaults.

 This defined group can be modified or deleted. The default permissions for this group are video Operators:

stream view, PTZ manipulation as well as the use of API.

NOTE: PTZ manipulation permission varies by applicable models.

 This defined group can be modified or deleted. The default permissions for this group are limited Viewers:

within video stream view and the use of API.

2. Click the Save button to save the settings and create a new user. The new user profile appears in the box on the

left side of the page. Click the Reset button to clear all of the information you entered without saving it.

 Username

Click in the Username box and type a user name (2 to 23 alphanumeric characters). User names are case-sensitive.

 Password

Click in the Password box and type a password (4 to 16 alphanumeric characters). Passwords are case-sensitive.

 Re-type Password

Click in the Retype Password box and retype your password.

Click the Save button to save the settings and create a new user (the new user profile appears in the box on the left side of the

page), or click the Reset button to clear all of the information you entered without saving it.

Deleting a User

1. Click the user profile that you want to delete from the defined users section located in the box on the left side of the

page.

2. Click the Delete User button. A dialog box appears with the message “Are you sure you want to delete this user?”

3. Click OK. The user profile is deleted from the defined user profiles section.

NOTE: adminThe default “ ” user cannot be deleted.

3.2.6 Events

Use the Events tab to configure camera events detections and the following handlers. Events detections are activated by

user-defined event sources that tell the device how to react when a specific event occurs. Event handlers are the actions that

the device takes when an event occurs. For example, an event source can be configured to alarm an operator via sending

email notification if . a motion occurs within the predefined camera’s coverage

F 3- : E S IGURE 41 VENTS ETTINGS

3.2.6.1 Alarm Source

This page allows user to configure the settings of t connected alarm input source, which is the external alarm signaling he

device, such as a door contact or motion detector. Both normally open and normally closed devices are supported.

F 3- : A SIGURE 42 LARM OURCE

Alarm Input Settings

1. Check button to enable . Enabled Alarm Input

2. Select either or Normally Open Normally Closed from the Polarity drop-down menu.

 An alarm will be triggered when the external contact closes.Normally Open:

 An alarm will be triggered when the external contact opens.Normally Closed:

Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

3.2.6.2 Motion Detection

This page is designed to define multiple groups of motion detection zones with specific own thresholds for triggering.

F 3-43: M Z A S IGURE OTION ONE REA ETTING

Motion Zone Area Setting

1. Check button to enable for any or all of Zones 1 to 4. Enabled Motion

NOTE: Click on the button “ ” to expand section of each zone setting, and click the button “ ” to collapse each section.

2. Choose different levels of sensitivity from , and .Sensitivity: High, Medium Low

 Motion is activ ed with slight changes in brightness or motion. High: at

 Motion is activated with big changes in brightness or motion. Low:

 The threshold of sensitivity is in the middle between High and Low. Medium:

3. can be defined from the range 1 to 100 for detection on wanted objects. Object Size

4. Set the desired area to trigger motion detection. The red frame of motion setup will appear for defining the

detection area by dragging the mouse.

3.2.6.4 Audio Detection

This function is designed to define the detailed settings for triggering surrounding audio detection. Check to have function this

enabled nder , adjust the threshold bar or input a number in the box right under it for the desired . U Sound Intensity Threshold

threshold level. A horizontal line, which indicates the exact threshold, in the box underneath will move up or down accordingly.

F 3-46: A DIGURE UDIO ETECTION

3.2.6.5 FTP Upload Handler

Under this page, camera can record and send snapshot files via properly predefined FTP settings for different events

composed of Alarm, Motion, Sabotage, Schedule as well as Audio Detection.

F 3-47: P U H IGURE FT PLOAD ANDLER

FTP Upload Handler

You can record and send event image files based on the condition you have set previously.

1. Check to enable for as well FTP Upload Handler Alarm, Motions 1 through 4, Sabotage Detection, Schedule,

as Audio Detection.

2. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

Remote Server

Remote Server is used as a service component to transfer files by simply entering the IP address or hostname with the Login

ID password. and

1. Input a server name or address. IP Address:

2. Port : Set “21” as default or change to dedicated number.

3. Input a user name with privilege to access the server. Username:

4. Input the password associated with Username.Password:

NOTE: Username Password guest 1234 e default Th and are “ ” and “ ”.

Settings

1. and Set Pre-event Snapshots, Post-event Snapshots, Pre-event Snapshot Interval, Post-event Snapshot

Interval Alarm, Motions 1 through 4 Sabotage Detection Schedule Audio Detection for , , , and selected.

2. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered

without saving it.

Snapshot Naming

By setting and for , andFile Name Prefix Server Path Alarm, Motions 1 through 4, Sabotage Detection, Schedule Audio

Detection selected, you will be able to save an image to a defined FTP server when any of your selected events is activated.

Set the where the data is to be stored on the server.Server Path

F 3-48: S N IGURE NAPSHOT AMING

You can also set time and determine the recording condition: , or from Trigger Interval OFF, All Day, Schedule 1 Schedule 2

scheduled table during 24/7 f The trigger interval can be adjusted on a scale bar with its corresponding seconds or Schedule.

shown in the box underneath.

F 3-49: U H S S IGURE FTP PLOAD ANDLER CHEDULED ETTINGS

Product specificaties

Merk:	Pelco
Categorie:	Bewakingscamera
Model:	Sarix Professional IBP521-1I

Heb je hulp nodig?

Als je hulp nodig hebt met Pelco Sarix Professional IBP521-1I stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera Pelco

Pelco Sarix Professional IMP521-1RS Handleiding

8 Juli 2023

Pelco GFC IMP IMP831-1RS Handleiding

8 Juli 2023

Pelco GFC Professional Multi IMD2007-1ES Handleiding

8 Juli 2023

Pelco Sarix Professional IXP33 Handleiding

7 Juli 2023

Pelco Esprit Enhanced ES6230-15 Handleiding

7 Juli 2023

Pelco Esprit Enhanced ES6230-12 Handleiding

7 Juli 2023

Pelco VideoXpert Enterprise VXS2-T144-N12 Handleiding

7 Juli 2023

Pelco EnduraXpress EE564-24B Handleiding

7 Juli 2023

Pelco Digital Sentry DSSRV2-040 Handleiding

7 Juli 2023

Pelco Sarix Professional IBP531-1ER Handleiding

6 Juli 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

HiLook THC-T150-M Handleiding

27 Maart 2025

YoloLiv VertiCam 1080p PTZ Handleiding

26 Maart 2025

Hanwha XNV-C6083R Handleiding

20 Maart 2025

Airlive AirCam PTZB-630MAI Handleiding

12 Maart 2025

Airlive AirCam BU-240M Handleiding

12 Maart 2025

Airlive AirCam PTZD-630MAI Handleiding

12 Maart 2025

Airlive AirCam BU-225S Handleiding

12 Maart 2025

Airlive AirCam VD-240M Handleiding

12 Maart 2025

Airlive AirCam VD-640MAI Handleiding

12 Maart 2025

Swann SWNVK-500KH4 Handleiding

11 Maart 2025