Pantum P3305DN Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Pantum P3305DN (110 pagina's) in de categorie Printer. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/110

Pantum P3010/P3060 Series
Pantum P3300/L2300/L2350/M118/M15 Series
Monochrome Laser printer
It is recommended that you read this Guide carefully before using the printer

II
Safety Precautions
Disconnect the power supply
The product should be placed close to or easily accessible to power sockets, so as to allow easy
disconnection of power supply!
Laser Safety
The laser radiation is harmful to the human body. Since laser components are completely sealed in
the printer, laser radiation will not leak. To avoid laser radiation, please do not randomly
disassemble the printer!
The printer follows the provisions of Class 1 laser products under CFR standard.
The printer has a Class III b laser diode, which has no laser radiation leakage among laser
components.
The laser components shall complies with the requirements of: U.S. Code of Federal Regulations,
21 CFR 1040, IEC 60825- 1.
The following label is attached to the laser components inside the printer:

III
Safety Warning
Please note the following safety warnings before using the printer:
Warning
There is high-voltage electrode inside the printer.
Before cleaning the printer, make sure the power is
turned o!
Plugging and unplugging the power cord plug with
a wet hand can result in an electric shock.
The fuser unit is hot when and after printing.
Touching the fuser unit (the shaded area as
shown) may cause burns!
The fuser unit is attached with a high temperature
warning label. Please do not remove or damage
this label.

IV
Precautions
Precautions before Using the Printer:
1. Read and understand all instructions;
2. Familiarize yourself with the basic principles associated with operating electrical appliances;
3. Comply with all warnings and instructions marked on the equipment or specified in the manual
supplied with the equipment;
4. If the operating instructions conict with the safety information, please refer back to the safety
information, as you may have misunderstood the operating instructions. If you cannot resolve the
conicts, please call the Customer Service Hotline or contact a service representative for help;
5. Before cleaning the equipment, remove the power cord from the AC power supply outlet. Do not
use liquid or aerosol cleaners;
6. Please make sure that the equipment is put on a stable desktop surface to avoid serious damage
caused by the falling of the equipment;
7. Do not put the equipment near a radiator, an air conditioner, or a ventilation pipe;
8. Do not put any articles on the power cord. Do not put the equipment at the place where its power
cord could be stepped on by people;
9. Outlets and extension cords must not be overloaded. This may reduce performance and could
result in re or electric shock;
10. Do not allow pets to chew on the AC power cord or the computer interface cable;
11. Do not allow sharp objects piercing equipment slot, so as to avoid contact with the high-voltage
device, which otherwise may result in re or electric shock. Take care not to spill liquids onto the
equipment;
12. Do not disassemble the equipment so as to avoid the risk of electric shock. Necessary repairs
may only be carried out by professional maintenance personnel. Opening or removing the cover
could result in an electric shock or other potential hazards. Incorrect disassembly and assembly
could also result in an electric shock during future use;
13. If any one of the following occurs, disconnect the equipment from the computer and pull out the
power cord from the AC wall socket and contact a qualied member of the service personnel for
maintenance:
• Liquid has been spilled into the equipment.
• The equipment has been exposed to rain or water.
• The equipment falls, or the cover is damaged.
• Significant changes in the equipment’s performance.
14. Only adjust the control mentioned in the instructions. Incorrect adjustment of other controls may
result in damage and mean that professional maintenance personnel need to spend more time
xing it;
15. Do not use the equipment in a thunderstorm so as to avoid the risk of an electric shock. If
possible, pull out the AC power cord during a thunderstorm;
16. If you continuously print multiple pages, the surface of the tray will become very hot. Take care
not to touch this surface, and keep children away from this surface;
17. The signal wire of the device connected with the printer can not be connected to the outdoors;
18. Please ensure timely ventilation in case of a prolonged use or printing huge amounts of
documents in a poorly ventilated room;

V
19. In standby status, the product will automatically enter into the power saving (sleep) mode if it
does not receive any job order for a while (such as 1 minute); and it can realize zero power
consumption only if it has not been connected with any external input power supply;
20. As the Class I equipment, the product must be connected to the power supply outlet with
protective grounding line when using;
21. This product should be placed according to the shipping marks on the product package box
during delivery;
22. This product is a kind of low-voltage equipment. When using this product below the specied
voltage range,please refer to the product precautions or call Pantum Aftersales Service Centre, if
the toner comes o the printed contents, or the equipment starts slowly;
23. This product is sold as a complete machine. The consumers can go to Pantum Aftersales
Service Centre to purchase parts they need. If the product sold is inconsistent with the package list,
please go to the specied Aftersales Service Centre to solve the problem;
24. Install this product in a place with the temperature between 10 and 35 and the relative ℃ ℃
humidity between 20% and 80%;
25. This device contains Part 15 of the FCC Rules and licence-exempt transmitter(s)/receiver(s)
that comply with Innovation,Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
26. Radiation Exposure Statement:
This equipment complies with Canada and FCC radiation exposure limits set forth for uncontrolled
environments.
This equipment should be installed and operated with a minimum distance of 20cm between the
radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
27. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.However, there is no
guarantee that interference will not occur in a particular installatio n.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
28. Warning: Changes or modications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
29. The power consumption of the product with wireless function is 3W/without wireless function is
2W in networked standby if all wired network ports are connected and all wireless network ports

VI
are activated.
30. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.
31. This Class B digital apparatus complies with Canadian ICES-003.
32. Please keep this User Guide properly.

VII
Legal Information
This symbol indicates that, at the end of your product’s life, it must not be discarded as
domestic waste. Instead, you should dispose of your used equipment at a designated
collection point for the recycling of waste electrical and electronic equipment. Ref: EU
Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). Please
contact your distributor / supplier for further information.
This product is suitable for indoor use only.
European Community (EC) directives conformity
This product complies with the protection requirements of EC directives 2014/30/EU and
2014/35/EU on the approximation and harmonization of the laws of the Member States
relating to electromagnetic compatibility and safety of electrical equipment designed for
use within certain voltage limits.
Radio Equipment directive 2014/53/EU only for models ending with sufx W “ ”.
The manufacturer of this product is: Zhuhai Pantum Electronics Co., Ltd., Building 02,06
and 08,No.888 Shengping Avenue, Pingsha Town, Zhuhai City, Guangdong Province,
519000 PR China.
A declaration of conformity to the requirements of the Directives is available upon
request from the Authorized Representative.
This product satises the Class B limits of EN 55032 / EN 55035 and safety requirements
of EN 62368-1.
This printer is fully compliant with the RoHS Directive 2011/65/EU for managing toxic and
hazardous substances.

1
1. Before Using the Printer
1.1. Product series introduction
Product series parameters
P3010D
series
P2800DW /
P3010DW
series
P3300
series
P3300DN
series
P3300DW/L2300DW
/L2350DW/M118DW/
M15DW series
Interface
type
USB
●
●
●
●
●
NET
●
●
●
Wi- Fi
●
●
Print
Language
GDI
●
●
PDL
●
●
●
Control
Panel
LED
●
LCD
●
●
●
●
Print
Speed
A4
30ppm
●
●
33ppm
●
●
●
Letter
32ppm
●
●
35ppm
●
●
●
Automatic Two-Sided Printing
●
●
●
●
NFC TAG
●
●
Mute printing
●
●
●
●
●
( : Support; Blank: Unsupport) ●
Note:
• This product series is subject to additions or changes without prior notice

5
1.4. Laser Toner Cartridge
Laser toner cartridge is composed of drum component and toner cartridge.
Service life of drum compo nent
Type
Average Print Volume
Standard drum component
About 12000 Pages(Based on ISO 19752 standard)
High volume drum component
About 25000 Pages(Based on A4/LTR size (3pages/job) )
Service life of toner cartridge
Type
Average Print Volume
Standard-volume toner cartridge
About 1500 Pages(Based on ISO 19752 standard)
High-volume toner cartridge
About 3000 Pages/6000 Pages(according to ISO 19752
standard)
Super large volume catridge
About 11000 Pages(Based on ISO 19752 standard)
Note :
• The model is subject to increase without notice.
• Consumables capacity may vary with different using types.
• The Company does not recommend using consumables other than the original
consumables provided, as any damages caused by non-original consumables are not
covered by the scope of warranty.
• Toner cartridge appearance may differ because of multiple volume and models, so the
schematic diagram is only for your reference.
• High volume drum component and super large volume catridge are only applicable to
some models, please refer to the specications of the model that you actually purchase

13
4. Raise the output tray to avoid the printed paper from slipping and falling, or immediately remove
the printed document after the printing is complete.
Note:
• It is recommended that you raise the output tray to prevent the paper from slipping and
falling after printing. If you choose not to raise the output tray, we recommend that you
immediately remove the printed paper from the printer.
• If more than 250 pages (80 g/m²) are put inside the auto feed tray at one time, paper
jam or paper feed failure will be led to.
• If carrying out single-sided printing, please make sure that the side to be printed (the
blank side) is face down.
2.3.2. Install manual feed tray
1. Raise the output tray to avoid the printed paper from slipping and falling, or immediately remove
the printed document after the printing is complete.
Product specificaties
Merk: | Pantum |
Categorie: | Printer |
Model: | P3305DN |
Kleur van het product: | Wit |
Ingebouwd display: | Ja |
Gewicht: | 6800 g |
Breedte: | 354 mm |
Diepte: | 334 mm |
Hoogte: | 232 mm |
Kleur: | Nee |
Beeldscherm: | LCD |
USB-poort: | Ja |
Ethernet LAN: | Ja |
Markt positionering: | Bedrijf |
Aantal USB 2.0-poorten: | 1 |
Stroomverbruik (in standby): | 50 W |
Intern geheugen: | 256 MB |
Ethernet LAN, data-overdrachtsnelheden: | 10, 100 Mbit/s |
Bekabelingstechnologie: | 10/100Base-T(X) |
Ondersteunt Windows: | Windows 10, Windows 11, Windows 7, Windows 8, Windows 8.1, Windows Vista, Windows XP |
Ondersteunt Mac-besturingssysteem: | Mac OS X 10.12 Sierra, Mac OS X 10.7 Lion |
Ondersteunt Linux: | Ubuntu 12.04, Ubuntu 14.04, Ubuntu 16.04, Ubuntu 18.04 LTS, Ubuntu 20.04 LTS |
Maximale resolutie: | 1200 x 600 DPI |
Printkleuren: | Zwart |
Papierlade mediatypen: | Card stock, Labels, Plain paper, Thick paper, Transparencies |
Printtechnologie: | Laser |
Modus voor dubbelzijdig afdrukken: | Auto |
Printsnelheid (zwart, standaardkwaliteit, A4/US Letter): | 33 ppm |
Duplex printen: | Ja |
Paginabeschrijving talen: | PCL 5e, PCL 6, PDF, PS3 |
Gebruiksindicatie (maximaal): | 80000 pagina's per maand |
Totale invoercapaciteit: | 250 vel |
Totale uitvoercapaciteit: | 150 vel |
Maximale ISO A-series papierformaat: | A4 |
ISO A-series afmetingen (A0...A9): | A6 |
Tijdsduur tot de eerste pagina (zwart, normaal): | 8.2 s |
Optionele connectiviteit: | Ethernet |
Gemiddeld stroomverbruik tijdens printen: | 525 W |
Geluidsdrukniveau (afdrukken): | 52 dB |
Papierlade mediagewicht: | 60 - 105 g/m² |
ISO B-series afmetingen (B0...B9): | B5 |
Aanbevolen gebruiksindicatie: | 1000 - 10000 pagina's per maand |
Multifunctionele ladecapaciteit: | 1 vel |
Multifunctionele lade: | Ja |
Ondersteunde server operating systems: | Windows Server 2003, Windows Server 2008, Windows Server 2012 |
Geluidsvermogens (stand-by): | 30 dB |
Wifi: | Nee |
AC-ingangsspanning: | 220 - 240 V |
AC-ingangsfrequentie: | 50/60 Hz |
Bedrijfstemperatuur (T-T): | 10 - 32 °C |
Relatieve vochtigheid in bedrijf (V-V): | 20 - 80 procent |
Heb je hulp nodig?
Als je hulp nodig hebt met Pantum P3305DN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Printer Pantum

20 December 2024

20 December 2024

20 December 2024

20 December 2024

20 December 2024

21 Augustus 2024

21 Augustus 2024

9 Juli 2024

25 Maart 2024

25 Maart 2024
Handleiding Printer
- Printer HP
- Printer Sony
- Printer Samsung
- Printer Xiaomi
- Printer Panasonic
- Printer Epson
- Printer LG
- Printer Huawei
- Printer Canon
- Printer Honeywell
- Printer Olympus
- Printer Toshiba
- Printer Xerox
- Printer Agfaphoto
- Printer AVM
- Printer Brother
- Printer Builder
- Printer D-Link
- Printer Dell
- Printer Digitus
- Printer Dymo
- Printer Epson 7620
- Printer Frama
- Printer Fujifilm
- Printer Fujitsu
- Printer Ibm
- Printer Intermec
- Printer Kern
- Printer Kodak
- Printer Kogan
- Printer Konica Minolta
- Printer Kyocera
- Printer Lenovo
- Printer Lexmark
- Printer Minolta
- Printer Mitsubishi
- Printer MSI
- Printer Nec
- Printer Paxar
- Printer Polaroid
- Printer Primera
- Printer Renkforce
- Printer Ricoh
- Printer Roland
- Printer Royal Sovereign
- Printer Sagem
- Printer Seiko
- Printer Sharp
- Printer Star
- Printer Thomson
- Printer Tomy
- Printer Toshiba TEC
- Printer Triumph-Adler
- Printer Velleman
- Printer Zebra
- Printer Oce
- Printer Oki
- Printer Olivetti
- Printer Olympia
- Printer CSL
- Printer Argox
- Printer DTRONIC
- Printer Metapace
- Printer Citizen
- Printer Nilox
- Printer Approx
- Printer Ultimaker
- Printer Custom
- Printer Bixolon
- Printer Brady
- Printer GoDEX
- Printer Testo
- Printer EC Line
- Printer Sawgrass
- Printer DNP
- Printer TSC
- Printer Equip
- Printer StarTech.com
- Printer Fichero
- Printer GG Image
- Printer Posiflex
- Printer ZKTeco
- Printer Star Micronics
- Printer Datamax-O'neil
- Printer Panduit
- Printer Dascom
- Printer HiTi
- Printer Vupoint Solutions
- Printer Elite Screens
- Printer Phoenix Contact
- Printer Videology
- Printer Colop
- Printer Raspberry Pi
- Printer Evolis
- Printer Unitech
- Printer Middle Atlantic
- Printer IDP
- Printer Fargo
- Printer Microboards
- Printer Mutoh
- Printer Tally Dascom
- Printer Nisca
Nieuwste handleidingen voor Printer

2 April 2025

2 April 2025

1 April 2025

1 April 2025

29 Maart 2025

29 Maart 2025

11 Maart 2025

11 Maart 2025

9 Maart 2025