Olympus Camedia E-20N Handleiding

Olympus Fotocamera Camedia E-20N

Lees hieronder de 📖 handleiding in het Nederlandse voor Olympus Camedia E-20N (2 pagina's) in de categorie Fotocamera. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

PProgram mode Camera selects the correct aperture and shutter

speed automatically.

AAperture priority mode Camera sets the correct shutter speed for the

aperture that you select by moving the sub dial

left or right.

SShutter priority mode Camera sets the correct aperture for the shutter

speed that you select by moving the sub dial left or

right.

MManual mode You select the aperture with the main dial and the

shutter speed with the sub dial.

3 Adjust the viewfinder for your eyes. If you wear eyeglasses, you may need to

sharpen the viewfinder display.

• If the AF target mark in the center of the viewfinder is not sharp, turn the diopter adjustment

ring around the viewfinder left or right until the AF target mark is sharp.

4 Select the memory card.

• If only one memory card is installed in the camera, the card is selected automatically for

storing pictures that you take. If both cards are installed, the control panel display will tell

you which card is currently selected for storing pictures.

SmartMedia memory card selected.

CompactFlash/Microdrive memory card selected.

• If you want to switch the selection, press and hold the SM/CF memory card button (K), then

turn the main dial until it clicks. In the control panel you should see or displayed.

Go!

1 Make sure that the lens cover has been removed.

2 Take a picture.

• Point the camera at the subject that you want to take a picture, and look through the

viewfinder to compose the picture.

• Turn the zoom ring to enlarge or reduce the size of the subject in the viewfinder.

• With the picture composed in the viewfinder, use the flat of your index finger to half-press

the shutter button ( ) and wait for the AF correct mark light in the lower left corner of thec

viewfinder to light. When you see the AF correct mark light, the picture is correctly focused

and exposure is calculated.

• Fully-press the shutter button to take the picture. After the shutter releases, the monitor on

the back of the camera briefly displays the image of the picture you have just taken and

then goes off.

• If you see the mark blinking in the viewfinder, this means that you should use the flash.

• On the left side of the camera, near the top, press the flash button to raise the built-in flash

unit. The flash will fire automatically to ensure correct exposure of the picture.

3 Repeat from Step 2 to take a few more pictures.

4 View the pictures that you have just taken.

• Set the mode dial to playback . The monitor on the back of the camera switches on and

you will see the the last picture taken.

• On the arrow pad, press or to display the other shots one by one.

• If you want to display several images at once so you can quickly locate a picture, turn the

main dial to the left. Every time you move the dial left you will see 4, 9, then 16 frames in

the monitor. This is called the index display where each set of 4, 9, or 16 frames are

displayed as an index.

• Press or to display the next index. On the arrow pad, press or to move the

green highlight within the displayed index to select the picture that you want to display.

• If you want to enlarge the display so you can check the focus of the picture, turn the main

dial clockwise to enlarge the display in steps. As you enlarge the display, the view becomes

smaller. Press on the arrow pad to scroll around the enlarged image. Turn the

main dial counterclockwise until the original display is restored.

5 Delete a picture.

• With the frame that you want to delete displayed in the monitor, press the erase button

on the back of the camera near the bottom edge. If you are using the index display, use

on the arrow pad to select the picture that you want to erase, and press the

erase button.

• To switch off playback, set the mode dial to P A S, , , or M.

]

[

Important Parts and Names

Digital Camera

Quick Start Guide

Follow these simple instructions to start using your camera in minutes. Read the other

instructions provided with the camera for detailed descriptions of all the exciting features that the

Olympus E-20 packs into its compact design.

Ready!

You have to complete several important tasks before you can use the camera.

1 Attach the strap.

• Thread the ends of the strap through the eyelets on both sides of the camera. Slide the

ends of the straps through the sleeve and frame, and then pull them tight. Slide the sleeve

up the eyelets on both sides.

2 Load the lithium battery packs provided with the camera.

• On the bottom of the camera, turn the battery compartment knob to the open position ,

open the compartment, and then remove the battery case.

• With the +/ polarities aligned correctly, insert the battery packs into the battery, taking care−

not to reverse the +/ polarity.−

• Load the case in the camera. Push down lightly on the compartment case, and then move

the battery compartment knob to the close position .

Note:

Your camera can also use the following types of batteries: AA (R6) Ni-MH ( 4), AA (R6) Ni-Cd×

(×4), B-12LPB/B-10LPB (included in the optional B-32LPS/B-30LPS lithium polymer battery

sets), and AA (R6) Alkaline (×4).

Caution:

Never use AA (R6) zinc-carbon (manganese) or AA (R6) lithium batteries with this camera.

These batteries could overheat and seriously damage the camera.

3 Insert the memory cards.

• The camera can hold one SmartMedia® and one CompactFlash®/Microdrive* (CF Type II

standard) memory card. Either card can be installed alone or both can be installed together,

but at least one memory card of either type must be installed in the camera before you take

pictures.

* Use of the Microdrive card requires the B-32LPS/B-30LPS lithium polymer battery set due

to the power requirements of the Microdrive.

• Hold the camera with the lens facing away from you. Lift up the card cover lock ( ) up whileJ

pressing the round release button under it to open the card cover.

• To install a SmartMedia card, hold it with its notched corner down, and insert it into the

thinner slot closest to the back of the camera. Gently push the card completely into the slot.

(Insert the SmartMedia card until you can see about 2 mm of the card above the edge of

the slot.)

• To remove the SmartMedia card, push it in gently to release and then pull it out of the slot.

• To install the CompactFlash/Microdrive card, hold the card so that the arrow on the card can

be seen and points into the slot, then insert it straight into the wider slot. Gently push in the

card until it stops.

• To remove the CompactFlash/Microdrive card, gently press the eject button below the slot.

Caution:

Careful! If you press the eject button too hard, the CompactFlash/Microdrive card could pop

out of the slot.

4 Switch the camera on.

• The power switch (O P) is underneath the mode dial ( ). Move the power switch toward you

to the ON position. The control panel on top of the camera comes on.

• The batttery check mark in the control panel on top of the camera tells you that the batteries

are fully charged. When this mark begins to blink, the batteries are low and you should

replace them as soon as possible. If this mark goes off, the batteries are dead and the

camera cannot be used unless you replace the batteries.

• The large number to the right of the battery check tells you the approximate capacity of the

selected card. As each picture is taken, this number will decrease until it reaches 0 and the

card is full.

• To switch the camera off, move the power switch forward to the OFF position.

5 Set the date and time.

• On the top right corner of the camera, set the mode dial to the setup/connection mode mark

• Press the menu button ). The menu appears in the monitor.(a

• On the arrow pad, press once to move the green highlight to the time setting mark .

• With the time setting mark highlighted, press once to move the green highlight to the

mark. Below the date, the date format, Y-M-D for example, where Y, M, D stand for the Year,

Month, Day, is displayed.

• Press or to select the date format (Y-M-D, M-D-Y, etc.), and then press . Two

pointers appear above and below the first setting.

• Now you can set the date. On the arrow pad, press or to increase or decrease the 2-

digit number. With the desired number displayed (12 for example) press to move the

pointers to the next position. (To return to the previous position, press .) Repeat this until

you finish setting the date and time. Note that the 24-hour system is used for the hours.

• When you finish the settings, press the button. The green highlight returns to the time

setting mark . Press the button again to close the menu.

Get Set!

1 If the lens cover is on the lens, remove it.

2 Select the shooting mode.

• Move the mode dial to the (Program mode) setting. With the mode dial set to , theP P

camera automatically selects the correct aperture and shutter speed for the best exposure.

This is the best setting if you are just getting started.

Four shooting modes are available. For details, refer to the Reference Manual.

1Metering mode button

2Drive button

3Remote cable jack

4Built-in flash

5Flash button

6Manual focus ring

7Zoom ring

8Exposure compensation button

9Macro button

0Flash synchro socket

AFocus mode switch

BStrap eyelet

CDC IN jack cap

DMonitor

EEyepiece shutter lever

FDiopter adjustment ring

GViewfinder

HMain dial

ICard cover

JCard cover lock

KSM/CF memory card button

LCard access lamp

MLight button

NAE lock button

OPower switch

PMode dial

QWhite balance mode button

RSub dial

SControl panel

TRecord mode button

UFlash mode button

VHot shoe

WVideo OUT jack

XUSB connector

YMonitor lock/release button

ZINFO button

[Protect button

\Erase button

]Arrow pad

^OK button

aMenu button

bMonitor button

cShutter button

dRemote control receiver/self-timer lamp

eStrap eyelet

fBattery compartment

gTripod socket

hLens

iQuick reference (one touch) white

balance button

jAF port

kSpeaker

More...

Important Points to Remember

•If the camera is left with the power on and not used for a specified amount of time (1 minute

unless you have changed this setting), it will enter the sleep mode and automatically switch

off the control panel and other displays to conserve battery power. To restore the camera to

normal operation, half-press the shutter button, or turn the zoom ring one position left or

right and then back to its original position.

•If the camera remains idle in the sleep mode for 1 hour, it will switch itself off automatically.

To restsore full operation, you must move the power switch to the OFF position and then

back to the ON position.

•To conserve battery power, we recommend that you purchase an optional Olympus

CAMEDIA-brand AC adapter and use it for long shooting sessions indoors. The camera

never enters the sleep mode while the AC adapter is connected to the camera and a power

outlet. You can power the camera with the AC adapter without removing the batteries.

•The amount of data required to store a picture depends on the subject, so you may be able to

store more or fewer images on a card. Because of this difference in size, you may not be able to

store another picture, even after you delete one image from the card with single- frame delete.

Storage capacity of a 16MB and 32MB memory card

The numbers of images per 16MB and 32MB memory are only approximate estimations.

Quality Resolution (pixels) Compression File Size Images per Card (Reference value)

(Default settings) (Default settings) (Reference value) 16 MB 32 MB

RAW* 2560 x 1920 (FULL)

1:1 (not compressed)

10 MB 1 shot 3 shots

TIFF 2560 x 1920 (FULL)

1:1 (not compressed)

15 MB 1 shot 2 shots

SHQ 2560 x 1920 (FULL)

1:2.7

3.9 MB 4 shots 8 shots

HQ 2560 x 1920 (FULL)

1:8

1.5 MB 10 shots 21 shots

SQ 1280 x 960 (SXGA)

1:8

320 KB 49 shots 99 shots

Because of the difference in memory partitions on the SmartMedia, CompactFlash, and Microdrive

cards, the number of images stored may vary due to the differences between the card formats.

When using a CompactFlash card, the actual capacity of the card will be slightly more or less

than the capacity indicated.

* To display RAW data files on a PC, CAMEDIA Master software or Adobe Photoshop is required.

(Photoshop requires the Olympus RAW data plug-in software.)

What’s on the menu?

This is a brief summary of the menus and how to use them. The menus are used to select special

settings for taking pictures. Use this summary as a quick reference. Detailed explanations about

these settings are provided in the Instructions.

Restoring the Default Settings

The default settings are the settings in effect when you purchased the camera. Some menu

settings are not released after the camera is switched off and switched on again so you may need

to do this occasionally to restore the camera to its original operating status, especially when you

are experimenting with the camera to learn how to use it.

The current settings are displayed in the control panel.

Some settings are also displayed in the viewfinder when you take a picture.

Slow

synchro

Flash off

Red-eye reduction

2nd-curtain

Record mode

Card error

Manual focus

Auto bracket

White balance

Memory gauge

Macro

Exposure compensation/

Exposure level

ISO

Image

adjustment

Battery

check

Conversion lens

Number of storable pictures

Selected memory cardSequential

shooting

Metering mode

Self-timer

Remote control

Aperture value

Shutter speed

Flash intensity control

SmartMedia

CompactFlash/Microdrive

Macro

AF correct mark

AE (Automatic Exposure) lock

White balance (Displays setting

other than AUTO)

Metering

mode

Flash warning

Aperture value

Shutter speed

Exposure compensation/

Exposure level

Playback Mode Menu

Set the mode dial to , and then press or to move the, then press the menu button

green highlight. The Playback Mode Menu has only 1 page.

Print Reserve Mode Menu

Set the mode dial to , press the menu button , and then press or to move the green

highlight. The Print Reserve Mode Menu has only 1 page.

Setup/Connection Mode Menu

Set the mode dial to , press the menu button , and then press to move the green

highlight. The Setup/Connection Mode Menu has only 2 pages.

Where to Go from Here

Read the Instructions. The Instructions provide details about all the exciting features of your

camera. Simple step-by-step instructions describe how to not only use the camera, but show you

how to download data from the memory cards to your computer for further processing with a

graphics software application, and so on. If you are new to digital photography, a detailed glossary

at the end of the Instructions explains many terms that are not explained here or in the Instructions.

Visit us on-line. You can contact us at www.olympus.com or contact your local Olympus

authorized digital camera dealer.

OLYMPUS AMERICA INC.

Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 631-844-5000

Technical Support (USA)

24/7 online automated help: http://support.olympusamerica.com/

Phone customer support: Tel. 1-888-553-4448 (Toll-free)

Our phone customer support is available from 8 am to 10 pm (Monday to Friday) ET

E-Mail: distec@olympus.com

Olympus software updates can be obtained at: http://olympus.com/digital/

OLYMPUS OPTICAL CO. (EUROPA) GMBH.

Premises/Goods delivery: Wendenstrasse 14-18, 20097 Hamburg, Germany

Tel. 040-237730

Letters: Postfach 10 49 08, 20034 Hamburg, Germany.

Hotline Numbers for customers in Europe:

Tel. 01805-67 10 83 for Germany

Tel. 00800-67 10 83 00 for Austria, Belgium, Denmark, France, Netherlands, Norway, Sweden, Switzerland,

United Kingdom

Tel. +49 180 5-67 10 83 for Finland, Italy, Luxemburg, Portugal, Spain, Czech Republic

Tel. +49 40-237 73 899 for Greece, Croatia, Hungaria and the Rest of Europe

Our Hotline is available from 9am to 6pm (Monday to Friday)

E-Mail: di.support@olympus-europa.com

Slide show (Automatic playback).

Copy images card-to-card.

Monitor brightness.

Delete all images from card, format card.

1/3

2/3

Select or cancel all pictures for printing.

Set date or time stamping on prints.

Select or cancel all pictures for index printing.

Set year/month/day format, and set current date and time.

Monitor preview mode.

When shooting in the (manual) mode, select:M

•MANUAL to check the image to be shot with the monitor, or

•AUTO to gain the best monitor image.

Switches histogram on and off.

Pixel mapping.

Checks the image processing circuit and adjusts the CCD.

Sleep mode timer setting.

Determines whether conversion lens is selected when marcro button is pressed.

After you replace a memory card, you can restart file numbering (RESET) or

continue sequential file numbering (AUTO).

1/2

2/2

VT320301Printed in Japan

1 The flash mode button and record mode button are on top of the

camera, just above the control panel.

2 To restore the default settings, press and hold down the flash mode button

and the record mode button together.

That is all there is to it!

How to Use the Menus

Four menus are provided: Shooting Mode, Playback Mode, Print Reserve Mode, and Setup/

Connection Mode.

1 To open a menu, set the mode dial on top of the camera to the appropriate

setting, and then press the menu button in the center of the back panel of

the camera.

2 Press or to move the green highlight in the left column to select the

icon for the setting that you want to change.

•Some Shooting Mode Menu and Setup/Connection Mode Menu have more than one page.

The notation in the upper right corner of the menu display tells you which page you are on

(1/3, 2/3, and so on.)

•If you press with the highlight at the last icon, the next page of the menu is displayed.

-or-

•If you press with the highlight at the first icon, the previous page of the menu is

displayed.

3 With the desired icon selected, press or to move the green highlight

right or left to the setting that you want to select.

•If the setting requires a number selection, press or to increase or decrease the

number.

4 Click the OK button to save your selection. The green highlight returns to the

icon on the left.

5 Click the OK button to close the menu and return to normal operation.

Shooting Mode Menu

Set the mode dial to , or , press the menu button , and then press or to moveP A S, , M

the green highlight. The Shooting Mode Menu has 3 pages.

Delete all images from selected SmartMedia or CompactFlash card, and format a card.

ISO (sensitivity) setting.

Flash intensity control.

Sharpness.

Overall image contrast.

Warning sound (ON, OFF).

Bracket same subject with 3 rapid shots with different exposures.

Record mode customization (resolution, compression).

Set interval time (specify time interval between shots during automatic time lapse

photography).

Shutter sound setting (high, low, OFF).

Image display after shooting.

Select IS mode/PS mode/Noise Reduct.

1/3

2/3

3/3

Shooting Mode Menu

Playback Mode Menu

Setup/Connection Mode Menu

Print Reserve Mode Menu

P A S M, , ,

Product specificaties

Merk:	Olympus
Categorie:	Fotocamera
Model:	Camedia E-20N

Heb je hulp nodig?

Als je hulp nodig hebt met Olympus Camedia E-20N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Fotocamera Olympus

Olympus Tough TG-805 Handleiding

15 November 2024

Olympus Tough TG-1 Handleiding

18 Juni 2023

Olympus SZ-31MR Traveller Handleiding

29 Mei 2023

Olympus µ-5010 Handleiding

28 Mei 2023

Olympus PEN E‑PL8 Handleiding

24 Mei 2023

Olympus Stylus Zoom 130 Handleiding

20 Mei 2023

Olympus µ TOUGH-8000 Handleiding

17 Mei 2023

Olympus µ-5000 Handleiding

16 Mei 2023

Olympus VG-130 Smart Handleiding

13 Mei 2023

Olympus C-200 Handleiding

11 Mei 2023

Handleiding Fotocamera

Nieuwste handleidingen voor Fotocamera

Kodak Ektar H35N Handleiding

14 December 2024

Kodak Step Touch Handleiding

14 December 2024

Kodak Advantix 3600ix Handleiding

14 December 2024

Kodak EasyShare C360 Zoom Handleiding

14 December 2024

Kodak EasyShare Z8612 IS Handleiding

14 December 2024

Imou Ranger Dual 10MP Handleiding

14 December 2024

Imou Ranger Dual 8MP Handleiding

14 December 2024

Imou Ranger Dual 6MP Handleiding

14 December 2024

Fujifilm Intax Wide 300 Handleiding

14 December 2024

Fujifilm Intax Mini Hello Kitty Handleiding

14 December 2024