Octane Fitness XR6000S Handleiding
Octane Fitness
Hometrainer
XR6000S
Lees hieronder de 📖 handleiding in het Nederlandse voor Octane Fitness XR6000S (2 pagina's) in de categorie Hometrainer. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
B-6 (2)
103743-001
Box Contents
Install Seat
A
Hardware Pack
Latin America/Asian Pacific
001-763-757-2662
Europe/Middle East/Africa
31-10-2662412
Questions?
octanefitness.com
113201-001 REV E Page 1/2
USA & Canada
888-OCTANE4
©2020 Octane Fitness. All rights reserved.
Base
(xR6000 shown)
Tools Required:
#2 Phillips screwdriver
17mm wrench
Moving Handlebars
(Right and Left)
112508-001
112509-001
Information Packet
113201-001 Assembly
107786-001 Safety Instructions
B-1 (1)
B-2 (1)
B-9 (4)
B-4 (2)
B-5 (4)
105717-001
8022048
B
Install
Mast
C
Install Console
Separate console back from console front; set console back aside (not shown).
Connect the C-SAFE cable from the mast cover to the console (cable not
shown). Note: If you are installing a 900 MHz accessory, remove and
discard the C-SAFE cable.
Connect heart rate cable attached to heart rate board on console back
to heart rate cable from mast (black, 6-pin connector).
Make additional cable connections from mast to back of console:
Standard Console:
power,
handlebars,
base,
LAN,
ground
Smart Console:
power,
handlebars,
base,
LAN
(leave ground unconnected)
Routing loose cables to user front side of mast brackets, attach console front to
top of mast with C-1 (quantity 4); tighten using Phillips #2 screwdriver. Remove
screw securing mast cover to mast; retain screw. (If C-SAFE cable is in use,
let mast cover hang from cable.)
For Smart console only: Install power switch; connect cable and power.
a. Remove rubber plug from mast cover (not shown).
b. Route two-connector end of switch cable (pre-connected to console) through the
opening where plug was removed. Attach connectors to tabs on switch
(either connector can go on either tab).
c. Press switch fully into opening of mast cover; let mast cover hang
from cables.
d. Connect power cord and power supply. Plug into base of unit
and wall socket to verify power to console. Unplug from wall socket before
continuing to step D.
Standard Console Box Contents
5mm hex wrench (provided)
Tools Required:
#2 Phillips Screwdriver
Information Packet (attached to console)
110601-001 Notice to Installers
111289-001 xR6000 Console Guide & Setup
Instructions–Standard Console
104198-001 Warranty
101315-001 Registration Card
Standard Console
(Front and Back)
8020168
Tools Required:
#2 Phillips Screwdriver
110601-001 Notice to Installers
111768-001 Console Guide & Set-up Instructions–
Smart Console
104198-001 Warranty
101315-001 Registration Card
Information Packet (attached to console)
Smart Console
(Front and Back)
8019479
Standard
Console
Smart
Console
Console to Base
(white, 14-pin)
Handlebar Control
(white, 7-pin) Console Ground
(metal; green wire from mast)
Reserved
(unused)
Audio for
Accessories
(unused)
Power
(white, 4-pin)
Power for
Accessories
(unused)
Reserved for
Software Field Update
(black)
LAN
(RS-232)
C-SAFE
(Connect from mast
cover in Step
)
Standard Console
Power Switch
111032-001
Power Supply
112584-001
#2 Phillips
C-1 (10)
100780-001
Hardware Pack
110622-001
#2 Phillips
C-1 (10)
100780-001
Hardware Pack
110622-001
F-2
(may be boxed separately)
Power Cord
107658-001
(may be boxed separately)
Smart Console
Handlebar Control
(white, 7-pin)
Console to Base
(white, 14-pin)
Power
(white, 4-pin)
LAN
(RS-232)
(on Android board
underneath)
Power for
Accessories
(unused)
(unused)
(unused)
(unused)
(unused)
(unused)
(unused)
C-SAFE
(Connect from mast
cover in Step )
Arm Pivot Cover–Large
(Right and Left)
113185-001
Hardware Pack
112844-001
6mm
5mm
B-6 (2)
112734-001
B-11 (4)
112223-001
B-13 (2)
B-12 (2)
B-10 (2)
101277-001
Console Mast
112738-001
Foot Rest/Accessory Tray
112824-001
Foot Pedals
(Right and Left)
116661-001
111660-001
Seat Back
Enter
PAUSE
CLEAR
Time Calories Distance Speed
HR% HR Level
Challenging intervals isolating legs for power and toning
Higher resistance intervals isolating arms, shoulders and chest
A built-in personal trainer to motivate you with intense intervals
HIIT BOOSTERS
Program
Workout
Narrow Grip Wide Grip
Reverse
Legs Only Resistance
+
Push Arms Pull Arms
Fast
PRESS TO ACTIVATE
Quick Start
Level
OCTANE
FAVORITES
MMA
30:30
(Install back cover
and mast cover, C-SAFE
cable not shown)
6mm hex wrench (provided)
6-c
F-2
(Install back cover
and mast cover, C-SAFE
cable and power switch
cable not shown)
F-2
F-2
6-d
Flat head screwdriver
Assembly Instructions
(not shown)
112832-001
113183-001
Arm Pivot Cover–Small
(Right and Left)
113182-001 113184-001
Smart Console Box Contents
Use 6mm hex wrench to remove bolt and
washer from right side of seat back axle;
slide axle out user left side.
Position seat back; insert axle from left side through seat back
bracket, aligning flat sides of axle and hole. Align washer and
bolt with axle; tighten with 6mm hex wrench to 19 ft-lb.
Insert spacer B-2 (quantity 1) through hole in damper. Tilt seat
and align damper/spacer in seat bracket. Insert screw B-1
(quantity 1) through bracket and damper/spacer;
tighten with 5mm hex wrench to 7 ft-lb.
Test seat height and tilt adjustments to verify function of locking
mechanisms (not shown). (On xR6000s, also test swivel mechanism.)
Remove all loose parts from packaging; use handle to
lift rear of base and gently roll unit off
shipping pallet.
112736-001 113194-001
109989-001 104757-001 103743-001
8008949
6mm Hex (1)
103083-001
5mm Hex (1)
Use #2 Phillips screwdriver to remove two screws
securing front and rear top shrouds and mast boot. Set
screws, shrouds, and mast boot aside (not shown).
Remove twist tie securing cable bundle; tip mast
upside down and route cables through hole in
bottom of mast to top of mast.
Slide mast over screws on base; insert screw B-3
(quantity 2) into holes in front of mast plate, tighten
with 6mm hex wrench.
Insert screw B-3 (quantity 2) into holes in top of
mast plate. Use 6mm hex wrench to tighten
all 6 screws to 30 ft-lb.
Align bottom of front top shroud with base, then tip up
into position. Position rear top shroud and mast boot,
then secure both top shroud pieces using #2 Phillips
screwdriver and two screws removed in step 1.
B-3 (4)
101295-001
6mm
100780-001
#2 Phillips
B-8(4)
13mm
13mm
6mm
Rubber mallet
(optional)
Side Step (2)
113208-001
(xR6000s only)
cables
through
here
13mm wrench
Read and understand the “Product Safety Information” manual
before assembly.
B-7 (2)
103393-001
Complete Console Setup according to instructions found in
the Console Guide
and Setup Instructions (Part Number 111289-001 – Standard Console or
Part Number 111768-001 – Smart Console).
Use a #2 Phillips screwdriver to attach back cover to console with C-1
(quantity 6); tighten. Reattach mast cover to mast with screw removed in
step C-5, taking care to tuck cables out of the way before securing to mast.
(Shown in Section C illustration).
Level machine; adjust and lock levelers using 17mm wrench.
Make sure nut is tight.
F
Complete Setup &
Level Machine
If you have the optional Personal Viewing System (PVS) accessory, refer to Personal Viewing System (PVS) Assembly Instructions
located in the box with your PVS accessory, then return to these instructions to complete final assembly.
If you have the optional 900 MHz accessory, refer to 900 MHz Assembly Instructions located in the box with your 900 MHz accessory,
then return to these instructions to complete final assembly.
STOP
D
Connect Battery & Attach Moving Handlebars
With upper pedal links positioned on front side of mast post, attach foot rest bracket to
mast with screw B-9 (quantity 4); tighten all 4 screws with 5mm hex wrench until tight.
To install foot pedal:
Place wave washer B-10 (quantity 1) on pedal crank axle, then press lower end of foot pedal
onto pedal crank axle. (Use a rubber mallet to assist if needed.)
Place washer B-5 onto screw B-11 (quantity 1 each). Insert B-11/B-5 assembly into lower
hub and into pedal crank axle; tighten with 6mm hex wrench to 19 ft-lb.
Press cap B-12 into place in lower foot pedal hub.
Place cap B-13 onto screw B-11 (quantity 1 each). Insert B-11/B-13 assembly through upper
pedal link into upper foot pedal hub; tighten with 6mm hex wrench to 19 ft-lb.
Repeat steps 2-4 for second foot pedal.
For xR6000s Only: Place side step next to one side of the unit with back of side step aligned
with back of foot platform. Carefully tip unit away from you and push side step under rail of
unit. Lower unit onto side step channel. Repeat for second side step.
Assembly Instructions
Latin America/Asian Pacific
001-763-757-2662
Europe/Middle East/Africa
31-10-2662412
Questions?
octanefitness.com
113201-001 REV E Page 2/2
USA & Canada
888-OCTANE4
©2020 Octane Fitness. All rights reserved.
E
Attach Foot
Pedals & Foot Rest
Use #2 Phillips screwdriver to remove 4 screws securing battery access panel.
Use flat screwdriver at the side corner seams to gently unsnap bottom of panel;
remove from unit and set aside with screws.
Use #2 Phillips screwdriver to remove 1 screw securing each crank arm cover; turn
each cover counter-clockwise to remove and set aside with screws.
Connect cable on battery to cable in base (if you have not already done so during
installation of PVS or 900MHz accessory). Connect power cord to wall socket.
To install moving handlebar:
Place washer B-5 on bolt B-4 (quantity 1 each); attach moving handlebar
at hub with B-4/B-5 assembly and tighten with 13mm wrench to 19 ft-lb.
Position pedal crank axle at top-most position. Insert arm link of moving handlebar
into arm link bracket, aligned with hole #1 on bracket. From the outside toward the
center of the unit, insert screw B-6 (quantity 1) into arm link bracket and through arm
link and nut B-7; tighten with 13mm wrench to 17 ft-lb. For a longer reach, use hole #2 in
the arm link bracket. You must use the same hole (#1 or #2) on both handlebars.
Position large arm pivot cover around handlebar shaft and slide down to hub,
inserting posts on pivot cover into square holes in hub. Use #2 Phillips screwdriver
to secure large arm pivot cover to hub with B-8 (quantity 1). Press tabs of small arm
pivot cover into slots in large arm pivot cover. Use #2 Phillips screwdriver to secure
small arm pivot cover with B-8 (quantity 1).
Complete steps 4-6 for second moving handlebar.
Verify that you have properly connected the battery (per step 1). Then, move
handlebars back and forth to check console power (not shown).
For standard console: Verify console powers up and stays lit for more than 5
seconds. For smart console: Press power switch to start console and verify
xR6000 landing screen displays.
Position each crank arm cover, turning it clockwise to lock into place, then secure
using #2 Phillips screwdriver and screws removed in step 2.
Position bottom of battery access panel and snap into place, then press top
of panel into place. Use #2 Phillips screwdriver and secure with
4 screws removed in step 1.
cables
not
shown
Install Side Steps
(xR6000s only)
(Console and mast
not shown)
snap
apart
here
Product specificaties
| Merk: | Octane Fitness |
| Categorie: | Hometrainer |
| Model: | XR6000S |
Heb je hulp nodig?
Als je hulp nodig hebt met Octane Fitness XR6000S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Hometrainer Octane Fitness
13 September 2023
13 September 2023
13 September 2023
13 September 2023
13 September 2023
13 September 2023
13 September 2023
13 September 2023
13 September 2023
13 September 2023
Handleiding Hometrainer
- Hometrainer Fysic
- Hometrainer Medion
- Hometrainer Ab Magic Pro
- Hometrainer Abtronic
- Hometrainer Athlett
- Hometrainer Batavus
- Hometrainer Beny Sports
- Hometrainer BH Fitness
- Hometrainer Blumill
- Hometrainer Body Action
- Hometrainer Body Action - Tommyteleshopping
- Hometrainer Body Sculpture
- Hometrainer Body Solid
- Hometrainer BodyCraft
- Hometrainer BodySculpture
- Hometrainer Bodystrong
- Hometrainer Bowflex
- Hometrainer Bremshey
- Hometrainer Bremshey Sport
- Hometrainer DKN
- Hometrainer Domyos
- Hometrainer Dr.Kern
- Hometrainer DS Produkte
- Hometrainer Dunlop
- Hometrainer Elite
- Hometrainer Elite Fitness
- Hometrainer Emotion Fitness
- Hometrainer Energetics
- Hometrainer Ergo-fit
- Hometrainer Everfit
- Hometrainer Finnlo
- Hometrainer First Degree
- Hometrainer Fit Bike
- Hometrainer Fitmaxx
- Hometrainer Flow Fitness
- Hometrainer Focus Fitness
- Hometrainer Fuel Fitness
- Hometrainer Gymform
- Hometrainer Hammer
- Hometrainer Hastings
- Hometrainer HMM
- Hometrainer Hollandia
- Hometrainer Horizon
- Hometrainer Horizon Fitness
- Hometrainer Icon
- Hometrainer Icon Sport
- Hometrainer Impec
- Hometrainer Infiniti
- Hometrainer Inspire
- Hometrainer Keiser
- Hometrainer Kettler
- Hometrainer Klarfit
- Hometrainer Kroon
- Hometrainer Lanaform
- Hometrainer LEG MAGIC
- Hometrainer Life Fitness
- Hometrainer LifeGear
- Hometrainer Lifespan
- Hometrainer Marcy
- Hometrainer Matrix
- Hometrainer Maxxus
- Hometrainer Media Shop
- Hometrainer Medisana
- Hometrainer Motion
- Hometrainer MP Products
- Hometrainer MPF
- Hometrainer MX Select
- Hometrainer Nautilus
- Hometrainer NordicTrack
- Hometrainer Perfectum Fitness
- Hometrainer Powerpeak
- Hometrainer Precor
- Hometrainer Pro-form
- Hometrainer Proteus
- Hometrainer Quality Sports
- Hometrainer Rambler
- Hometrainer RB Sports
- Hometrainer Reebok
- Hometrainer Rossler
- Hometrainer S Sports
- Hometrainer Schwinn
- Hometrainer Senz Sports
- Hometrainer Skandika
- Hometrainer Slazenger
- Hometrainer Sole Fitness
- Hometrainer Spirit
- Hometrainer Sportop
- Hometrainer Sportplus
- Hometrainer SportsArt
- Hometrainer Sportstech
- Hometrainer Sporttronic
- Hometrainer Stairmaster
- Hometrainer Stamina
- Hometrainer Stamm
- Hometrainer Star Uno
- Hometrainer StarTrac
- Hometrainer StrengthMaster
- Hometrainer Tacx
- Hometrainer Taurus
- Hometrainer Technogym
- Hometrainer Tel Sell
- Hometrainer Thane
- Hometrainer Tommy Teleshopping
- Hometrainer Toorx
- Hometrainer Tunturi
- Hometrainer U.N.O.
- Hometrainer Van Speijk
- Hometrainer Vasa
- Hometrainer Vermeiren
- Hometrainer Vibrafit
- Hometrainer Vibrofit
- Hometrainer Vibroplate
- Hometrainer VirtuFit
- Hometrainer Vision Fitness
- Hometrainer Vitalmaxx
- Hometrainer Wahoo
- Hometrainer Waterrower
- Hometrainer Weider
- Hometrainer Weslo
- Hometrainer Wonder Core
- Hometrainer Xelus
- Hometrainer Xterra
- Hometrainer Yellow Sport
- Hometrainer Jetstream
- Hometrainer Jocca
- Hometrainer Joy Sport
- Hometrainer Omni
- Hometrainer Christopeit
- Hometrainer Concept2
- Hometrainer Crivit
- Hometrainer DC Athletics
- Hometrainer Striale
- Hometrainer York Fitness
- Hometrainer Kayoba
- Hometrainer Biltema
- Hometrainer Spokey
- Hometrainer Crane
- Hometrainer Capital Sports
- Hometrainer Body Bike
- Hometrainer Cardiostrong
- Hometrainer Darwin
- Hometrainer Magene
- Hometrainer Life Gear
- Hometrainer ProForm
- Hometrainer Delta Sport - Lidl
- Hometrainer Eco Run
- Hometrainer Gymrex
- Hometrainer Kendox
- Hometrainer Rebblo
- Hometrainer Viking Choice
- Hometrainer Assault Bike
- Hometrainer Motive Fitness
- Hometrainer Assault Fitness
Nieuwste handleidingen voor Hometrainer
17 December 2024
7 September 2024
20 November 2024
15 November 2024
2 November 2024
2 November 2024
16 Oktober 2024
7 Oktober 2024
7 Oktober 2024
30 September 2024