Netgear GS316PP Handleiding

Netgear Schakelaar GS316PP

Lees hieronder de 📖 handleiding in het Nederlandse voor Netgear GS316PP (4 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

are trademarks of NETGEAR, Inc. Any non‑NETGEAR

trademarks are used for reference purposes only.

Installation Guide

1. Search for NETGEAR Insight and download the latest app.

2. Set up a NETGEAR account if you do not have one.

3. Tap the menu in the upper-left corner.

4. Tap REGISTER ANY NETGEAR DEVICE.

5. Enter the serial number located on the bottom of the switch, or use the

camera on your mobile device to scan the serial number bar code.

6. Tap .GO

The switch is registered and added to your account. You can now view the

switch in the NETGEAR Insight app.

Note: Because this is an unmanaged switch, you cannot congure or manage it

in NETGEAR Insight.

Connect the switch

1. Connect network devices to the ports on the switch.

2. Connect an RJ-45 port on the switch to a network.

Note: In a small ofce or home ofce network, connect the switch to the LAN

port of a router that, in turn, is connected to an Internet modem.

3. Power on the switch.

PoE considerations

The switch prioritizes the PoE+ power that it supplies in ascending port order

(from port 1 to port 16). If the aggregate power requirements of all attached

power devices (PD) exceed the power budget of the switch, the PD on the

highest-numbered port is disabled to make sure that the PDs that are connected

to the higher-priority, lower-numbered ports are supported rst.

The following tables describe the power adapter models that are compatible with

the GS316P and GS316PP switches and their PoE classes and switch allocations:

Note: The listed total power budget is the maximum power limit for the

switch. Many PDs require less than maximum power, so the aggregate power

requirements are lower than the maximum, allowing all sixteen PoE ports to be

active simultaneously.

Power adapters and total power budgets for the GS316P and GS316PP:

Power adapter model Power adapter Total power budget

EPS90W 90W 76W

EPS130W 130W 115W

EPS200W 200W 183W

PoE classes and switch allocations:

Device

class

Standard Class

description

Minimum power

allocated to the

powered device

Range of power

delivered to the

powered device

0 PoE and PoE+ Default power

(full)

0.44W 0.44W–12.95W

Device

class

Standard Class

description

Minimum power

allocated to the

powered device

Range of power

delivered to the

powered device

1 PoE and PoE+ Very low

power

4.0W 0.44W–3.84W

2 PoE and PoE+ 7.0W 3.84W–6.49WLow power

3 PoE and PoE+ Mid power 15.4W 6.49W–12.95W

4 PoE+ only High power 30.0W 12.95W–25.5W

PoE troubleshooting

Here are some tips for correcting PoE problems that might occur:

• Make sure that the PoE Max LED is off. If the PoE Max LED is solid yellow,

disconnect one or more PoE devices to prevent PoE oversubscription. Start by

disconnecting the device from the highest-numbered port.

• Make sure that the Ethernet cables are plugged in correctly. For each

powered device (PD) that is connected to the switch, the corresponding right

port LED on the switch lights solid green. If the right port LED lights solid

yellow, a PoE fault occurred and PoE halted because of one of the conditions

that are listed in the following table.

PoE Fault Condition Possible Solution

A PoE-related short circuit occurred on the

port.

The problem is most likely with the attached

PD. Check the condition of the PD or restart the

PD by disconnecting and reconnecting the PD.

The PoE power demand of the PD exceeded

the maximum level that the switch permits,

which is 30.9W.

The PoE current on the port exceeded the

classication limit of the PD.

The PoE voltage of the port is outside the

range that the switch permits.

Restart the switch to see if the condition

resolves itself.

16-port Gigabit Ethernet Unmanaged

High-Power PoE+ Switch with FlexPoE

Models GS316P and GS316PP

Package contents

• Switch

• Power cord (varies by region)

• Power Adapter (130W for GS316P/200W for GS316PP)

• Wall installation kit

• Rubber feet

• Mounting ties (for power adapter)

• Rack-mount kit for rack installation

• Installation guide October 2019

Sample connections

PoE VoIP

Phone

Wave 2

Wireless AP

PoE+ security

camera

Router

GS316PP

Internet

Laptop

Smart

phone

Internet

PoE+

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

NETGEAR INTERNATIONAL LTD

Floor 1, Building 3

University Technology Centre

Curraheen Road, Cork,

T12EF21, Ireland

Cables and speeds

The following table describes the network cables that you can use for the switch

connections and the speeds that thesse cables can support, up to 328 feet (100

meters).

Speed Cable Type

100 Mbps Category 5 (Cat 5) or higher

1 Gbps Category 5e (Cat 5e) or higher

Attach the switch to a wall

To attach the switch to a wall, you need the wall-mount screws that are supplied

with the switch.

Check the PoE status

Power LED Left Port LEDs Right PoE LEDs

On 1000 Mbps link PoE in use

Off 100 or 10 Mbps link PoE halted (see PoE

troubleshooting)

Activity (blinking) No PoE use (off)

No link (off)

The switch can supply up to 30W PoE+ (IEEE 802.3at) to each port, with a maximum PoE power

budget of 76W total with a 90W power adapter, a 115W total with a 130W power adapter and a

183W total with a 200W power adapter across all active PoE+ ports.

The PoE Max LED indicates the status of the PoE budget on the switch:

Solid yellow. Less than 7W of PoE power is available on the switch.

Blinking yellow. The PoE Max LED was lit solid in the previous two minutes.

Sufcient (more than 7W of) PoE power is available on the switch (the LED is off).

Change the switch’s PoE budget

You can move the slider on the back of the switch to increase or decrease the

PoE budget. You can increase the PoE budget if you buy a higher wattage power

supply. You also can move the slider to a PoE budget that is lower than the power

supply wattage. This reduces your switch’s power consumption. However, we

recommend using the slider setting that matches your power supply.

1. Power down the switch and disconnect the

power cord.

2. Move the slider to the setting that

corresponds to the wattage of the new

power adapter.

3. Connect the power cord and power on the

switch.

Specications

Specication Description

Network interfaces 16 Gigabit Ethernet RJ-45 ports that support 1G, 100 M, and 10 M

16 PoE/PoE+ ports

Power adapter input Power adapter varies by region.

Power adapter output The switch supports three power adapters:

200W: 54V @ 3.7A

130W: 54V @ 2.4A

90W: 54V @ 1.66A

Max PoE budget The maximum budget for each power adapter is as follows:

200W: 183W PoE

130W: 115W PoE

90W: 76W PoE

Dimensions (W x D x H) 11.26 x 4.02 x 1.06 in. (286 x 102 x 27 mm)

Weight 1.94 lb (0.88 kg)

Operating temperature 32–104°F (0–40°C)

Operating humidity 10%–90% relative humidity, noncondensing

Compliance FCC class A, CB, CE class A, VCCI class A, RCM class A, KC, BSMI

To attach the switch to a wall:

1. Locate the two mount holes on the bottom panel of the switch.

2. Mark and drill two mounting holes in the wall where you want to mount the

switch.

The two mounting holes must be at a precise distance of 4.27 in. (108.4 mm)

from each other.

3. Insert the supplied anchors into the wall and tighten the supplied screws with

a No. 2 Phillips screwdriver.

Note: Leave about 0.125 in. (4 mm) of each screw protruding from the wall so

that you can insert the screws into the holes on the bottom panel.

Install the switch in a rack

To install the switch in a rack, you need the rack-mount brackets and screws that

are supplied with the switch.

To install the switch in a rack:

1. Attach the supplied mounting brackets to the side of the switch.

Insert the screws provided in the product package through each bracket and

into the bracket mounting holes in the switch.

2. Tighten the screws with a No. 2 Phillips screwdriver to secure each bracket.

3. Align the mounting holes in the brackets with the holes in the rack, and insert

two pan-head screws with nylon washers through each bracket and into the

rack.

4. Tighten the screws with a No. 2 Phillips screwdriver to secure mounting

brackets to the rack.

Support

Thank you for purchasing this NETGEAR product. You can visit

https://www.netgear.com/support/ to register your product, get help, access the

latest downloads and user manuals, and join our community. We recommend that

you use only ofcial NETGEAR support resources.

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en

français canadien à https://www.netgear.com/support/download/.

(If this product is sold in Canada, you can access this document in Canadian

French at https://www.netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of

Conformity, visit https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

Do not use this device outdoors. If you connect cables or devices that are

outdoors to this device, see https://kb.netgear.com/000057103 for safety and

warranty information.

Product specificaties

Merk:	Netgear
Categorie:	Schakelaar
Model:	GS316PP
Kleur van het product:	Zwart
Gewicht:	880 g
Breedte:	286 mm
Diepte:	102 mm
Hoogte:	27 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Activity, Link, PoE, Power, Speed
Stroom:	3.7 A
Vermogensverbruik (max):	195.9 W
DC voltage input:	54 V
Certificering:	CE, FCC Part A, IC A, RCM, VCCI, BSMI, KC, CB, CE LVD
Netwerkstandaard:	IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3az, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x
Temperatuur bij opslag:	-20 - 70 °C
Rack-montage:	Ja
Mean time between failures (MTBF):	2362192 uur
Hoogte, in bedrijf:	0 - 3000 m
Ophangsysteem voor aan de muur:	Ja
Quality of Service (QoS):	Ja
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Ja
Switchingcapaciteit:	32 Gbit/s
MAC-adrestabel:	4000 entries
10G support:	Nee
Datastroombeheer:	Ja
Switch type:	Unmanaged
Aantal basis-switching RJ-45 Ethernet-poorten:	16
Netstekker:	DC-in ingang
Type basis-switching RJ-45 Ethernet-poorten:	Gigabit Ethernet (10/100/1000)
Packet buffergeheugen:	1 MB
Latentie (1 Gbps):	3.7 µs
Jumbo Frames ondersteuning:	Ja
Full duplex:	Ja
Warmtedissipatie:	669.9 BTU/h
Auto-negotiation:	Ja
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Code geharmoniseerd systeem (HS):	85176990
Totaal Power over Ethernet (PoE)-budget:	183 W
Aantal Power over Ethernet plus (PoE +)-poorten:	16
Jumbo frames:	9216
Vermogen per poort Power over Ethernet (PoE):	30 W
Auto-sensing:	Ja
Algoritmen wachtrijplanning:	Weighted Round Robin (WRR)
Packet forwarding rate (1 Gbps):	1448000 pps