Muse M-092 MR Handleiding

Muse Autoradio M-092 MR

Lees hieronder de 📖 handleiding in het Nederlandse voor Muse M-092 MR (2 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Detach the Front Panel

Press button in the upper left corner, and then the front panel will be folded down.

When the front panel was turned down to the angle of 45°, hold and push the front

panel to left, and then pull it out.

POWER button

(release button)

SEL/VOL knob (Audio/ volume)

SD/SDHC/MMC card slot

LCD display

TA button (Trafc Announcement)

AF button (Alternative Frequency)

Reset button

USB port with lid

AUX in jack

0/DSP button (Display time)

PTY button (Program type selection)

6/DIR+ button (Directory up)

Do not attempt to modify the unit, modifying the unit may cause an accident.

Installation or servicing of the unit by persons without training and experience in

electronic equipment and automotive accessories may be dangerous and could

expose you to the risk of electric shock or other hazards.

Stop the vehicle before carrying out any operation that could interfere with your

driving.

Keep the volume at a level which you could hear sounds from outside the vehicle.

Do not work in extremely high or low temperature. Be sure the temperature inside

the vehicle is between +60°C and -10°C before turning on your unit.

When replacing the fuse(s), the replacement must be of the same amperage as

shown on the fuse holder.

Do not block vents or radiator panels. Blocking them will cause heat to build up

inside and may result in re.

Using this unit without running the engine can result in battery drainage

Use only in cars with a 12 volt negative ground.

After completing the installation or replacing the car battery you need to RESET the

unit before using it. Remove the front panel and press RESET button on the base

with pointed object (such as ball-point pen) to reset the unit to its initial settings.

10.

GB - 1

M-092 MR

User Manual

CAR RADIO WITH USB & SD

Please read the instructions carefully before

operating the unit.

PRECAUTIONS

English GB - 2 GB - 3

CONNECTION

1. Antenna socket

2. Line out (Right-Red)

3. Line out (Left -White)

4. Output plug (male)

5. Output plug (female)

6. Fuse holder (5A)

Caution!

- Make sure to connect the colour coded leads according to the diagram. Incorrect

connections may cause the unit to malfunction or damage the vehicle’s electrical sys-

tem.

- Make sure to connect the speaker (-) leads to the speaker (-) terminal. Never con-

nect the left and right channel speaker cables each other or to the vehicle body.

- Make sure all the connections are completely correct before turning on your unit.

GB - 5

Install the front panel

Put notch A (Shown as picture) onto shaft B. And then slightly press into the right side.

Note: Never put any objects into the front panel.

Detach the Unit

1. Detach the front panel. (Please refer to upper part)

2. Take out the outer trim frame.

LOCATION OF CONTROLS

Front panel

GB - 7

- Method 2 DIN Rear-mount (For Japanese car)

1. Remove the outer trim frame

UNPACK YOUR UNIT

When you unpack your new car radio, make sure that you have removed all the acces-

sories and information papers:

Main unit with connector

User manual

Accessories:

Install the unit

- Method 1: DIN Front-Mount

INSTALL AND REMOVE THE UNIT 2. Select a position where the screw holes of the mounting bracket supplied with the

car and the screw holes of the main unit become aligned (are tted).

Base

5/DIR- button (Directory down)

4/RDM button (Random)

3/RPT button (Repeat)

2/INT button (Intro)

1/PAU button (Pause)

BAND/LOUD button

AMS/SCH button (Automatic scan and

memorising)

7/MODE button

EQ button (equalizer)

8/ button (skip backward)

9/ button (Skip forward)

3. Tighten the screws. And then fasten them to the car.

3. Insert the keys supplied on the both sides of the unit (shown as illustrated) until

they click. Pulling the keys and makes them to remove the unit from the dashboard.

10.

11.

12.

13.

GB - 4

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

23 24

Do not connect the ignition wire (red) and the battery wire (yellow), it may cause

a short circuit, even result in re.

Steel Bar X1

1 2 3 4

5 6 7 8

9 10 11 12

Output plug

(female)

Line out

(Left-White)

Line out

(Right-Red)

Fuse holder (5A)

Output plug (male)

GB - 6

1 2 3 5 6 7 9

1112131415161718192021

2324

AR-3111 IB MUSE 001 REV0 -GB.ind1 1 7/7/2011 5:03:27 PM

To reduce the risk of re or electric shock, do not expose this appliance to rain or mois-

ture.

If at any time in the future you should need to dispose of this product please

note that Waste electrical products should not be disposed of with house-hold

waste. Please recycle where facilities exist. Check with your Local Au-thority

or retailer for recycling advice.(Waste Electrical and Electronic Equipment

Directive).

ATTENTION : To reduce the risk of electric shock, do not remove

the cover. There are no user serviceable parts inside the unit. Re-

fer all servicing to qualied personnel.

GB - 15

WARNINGS

GB - 14GB - 13GB - 12

GB - 11GB - 10GB - 9GB - 8

The exclamation point within the triangle is a warning sign alerting the user of

important instructions accompanying the product.

The lightening ash with arrowhead symbol within the triangle is a warning

sign alerting the user of “dangerous voltage” inside the unit.

LISTENING TO AUXILIARY SOURCE TROUBLE SHOOTING GUIDE

SPECIFICATIONS

Symptom Cause Solution

LISTENING TO USB DEVICE OR SD/SDHC/MMC CARD

Scanning and memorizing stations

Automatic memory storing

In tuner mode, press and hold (20) button for 3 seconds to start automatic AMS/SCH

scanning and station store on numeric buttons 1-6.

- Preset scan

Press (20) button shortly to start preset stations scan. All preset stations are AMS/SCH

scrolled during few seconds. To remain on a station, press again the (20) AMS/SCH

button.

- Preset buttons (13-18)1- 6

1. Tune to a station with or (23/24).

2. Press and hold one of the preset buttons (13-18) for 2 seconds until LCD shows 1- 6

the corresponding number, which indicates that station is stored on this number.

3. In radio mode, press preset buttons (13-18) to listen to stored stations.1- 6

Note: The unit can be stored up to 6 stations for each band.

-LOC ON/ OFF: SEL/VOLRepeatedly press knob (3) to select “LOC” mode. When

ON, the strong signal local stations can be received, when OFF, the week signal out-of-

town stations may be received.

-STEREO / MONO: SEL/VOL Repeatedly press knob (3) to select “STEREO/ MONO”

mode. FM listening is generally done in Stereo mode. However, if the signal is weak or

reception is not as good as you would like, switching to Mono mode usually improves

the overall sound quality.

RDS (Radio Data System)

This unit has a built-in RDS decoder system that supports broadcast stations trans-

mitting RDS data. This system can display the name of the broadcast station being

received (PS) and can automatically switch to the broadcast station with the best re-

ception as you move on long distances (AF switching). Also, if a trafc announcement

(TA) or programme type (PTY) is broadcast from a RDS station, no matter what mode

you are in, this broadcast is received. Additionally, if EON information is received, this

information enables automatic switching of other preset stations on the same network

and interruption of the station being received with trafc information from other stations.

This function is not available in some areas.

- Alternative frequency selecting (AF)

The AF function switches automatically to a different frequency on the same network in

order to maintain optimum reception. Press button (7) to select AF function. If the AF

reception of the current broadcast station deteriorates, “AF” appears in the display and

the radio searches for the same program on another frequency. Press AF button (7)

again to cancel this function.

When reception is bad, the “AF” icon blinks.

Press and hold button (7) for 5 seconds to switch between “REG ON” and “REG AF

OFF” mode:

REG ON: should be selected to listen to the REGIONAL broadcast of the current sta-

tion, even if there is a national broadcast of this station.

REG OFF: should be selected to listen to the national broadcast of the current station.

- Trafc announcement (TA)

In the TA standby mode, when a trafc announcement broadcast starts, this one is re-

ceived with top priority that you can listen to it, regardless of the current function mode.

Trafc programme (TP) automatic tuning is also possible.

Press TA button (6), when LCD shows “TA”, traffic program will be automatically

searched and saved. When LCD shows “TP”, this means that the RDS broadcast sta-

tion being received has trafc announcement programmes.

If you press TA button (6) while a trafc announcement broadcast is being received,

the trafc announcement broadcast reception is cancelled and the unit goes into the TA

standby mode.

If a TP station is not found, the unit continues searching, “TA SEEK” is displayed.

Press TA button (6) again to stop searching, “TA” goes off.

ALARM

“ALARM” is displayed when an emergency broadcasting is received and the sound

level is set to the preset output level (TA Volume) automatically.

EON: (Enhanced Other Networks Information)

Press and rotating SEL/VOL (3) to select EON mode, EON ON. When receive the

EON information, the EON indication is on. With EON facility, it offers the ability for

local stations to ”break into” a national station’s broadcast for the duration of a Trafc

Announcement.

Program type (PTY) selection

When is selected (12), the radio starts to search for corresponding PTY informa-PTY

tion and stops when a corresponding station is found.

If corresponding PTY information is not found, the PTY search mode is automatically

stopped.

Press repeatedly PTY button (12) to set as follows:

Within above 2 groups, press repeatedly a preset number knob to select a program

type as follows:

To insert a SD, SDHC or MMC card (not included)

Press button (2) to fold down the front panel rst, take out the front panel, and In

sert your SD, SDHC or MMC card in the card slot (4). Install and close the front panel,

playback will start automatically. If a card has already been inserted, press but- MODE

ton (21) to switch to card mode.

Basic player functions

Play/Pause: 1/PAU press (18) to suspend momentarily the track playback. Press (18)

again to resume playback.

Skip/Fast search: press button (24) to skip forward to next track and (23) to

skip backward to previous track. Press and hold or (23/24) to search quickly

within a track.

Intro scan: 2/INT press button (17), “INT ON” is displayed, the set will play the rst

10 seconds of each track of the USB device or SD/SDHC/MMC card. Press it again to

cancel this function and keep on playing the current track. “INT OFF” is displayed.

Repeat: RPTPress button (16) once to repeat the current track. Press it twice to re-

peat the current directory. Press three times to repeat all.

Random playback: RDM Press button (15), “RDM ON” is displayed, all tracks will be

played randomly. Press it again to cancel this function, “RDM OFF” is displayed.

SELECTING A DIRECTORY: DIR DIR Press - button (14) or + button (13) to select di-

rectory downward or upward. If the MP3 contents does not have any directory, - (14) DIR

and + buttons (13) are inactive.DIR

Searching a track in MP3-USB/SD

1. Press button (20) once, AMS/SCH

2. Use the numeric keys to enter the track number,

3. Press knob (3) to start playing.SEL/VOL

Exit USB/SD card mode

To exit USB or card mode, disconnect your USB device or your card from the unit, the

set will switch to tuner mode automatically.

Note

* There are many USB devices or SD/SDHC/MMC card in the market. We cannot

guarantee to support all different models. Please try another USB device or SD/SDHC/

MMC card if yours is not supported.

* The unit might not support all the multimedia les stored in SD/SDHC/MMC card or

USB because it includes some special playback procedure which might not be compat-

ible with the procedure of this unit.

1. Connect your auxiliary source (e.g. MP3 player) to the AUX IN jack (10)

2. Press (1) button to turn the unit on.POWER

3. Press (21) to select AUX mode.MODE

4. Start playback from your auxiliary source.

5. Adjust the volume (3) to desired level.

6. To stop, disconnect your auxiliary source from the Aux in jack (10), press but-MODE

ton (7) to select other source.

To insert a USB device (not included)

Open the plastic lid, connect your USB device to the USB port (9), the set will switch to

“USB” mode automatically. If USB has already been inserted, press button (21) MODE

to switch to USB mode.

MUSIC group

1. POP M, ROCK M

2. EASY M, LIGHT M

3. CLASSICS, OTHER M

4. JAZZ, COUNTRY

5. NATION M, OLDIES

6. FOLK M

SPEECH group

1. NEWS, AFFAIRS, INFO

2. SPORT, EDUCATE, DRAMA

3. CULTURE, SCIENCE, VARIED

4. WEATHER, FINANCE, CHILDREN

5. SOCIAL, RELIGION, PHONE IN

6. TRAVEL, LEISURE, DOCUMENT

MAINTENANCE

Precaution

- Clean the front panel with a soft cloth, or damp chamois leather. Never use solvents.

- Do not expose to rain or water;

- Do not drop or apply shock.

- Make sure that you keep your set away from water and high temperatures.

- The use of apparatus in moderate climates.

- Do not be exposed to dripping or splashing, and that no object lled with liquids, such

as vases, shall be placed on the apparatus.

- No naked ame sources such as lighted candles should be placed on the apparatus.

Cleaning the Connector

If the connector between the main unit and the front panel is dirty, it may result in ab-

normal working condition. To avoid such problems, detach the front panel and clean

the connector with an alcohol swab. Gently clean to avoid damaging the connector.

Notes:

For the sake of safety, always shut down the generator and take out the key from the

ignition before cleaning. Never keep your nger or any metal device in contact with the

connector directly.

Replacing the Fuse

Make sure the amperage matches the specied value when replacing the fuses. If the

fuse is blown, check the power connection and replace with a new one. If the same

problem occurs, it could be caused by an internal malfunction. In such cases, please

consult the nearest service dealer.

No power.

No sound.

The car ignition switch is not

on.

The fuse is blown.

If the power supply is connected

to the car accessory circuits, but

the engine is not moving, switch

the ignition key to “ACC”.

Replace the fuse.

Adjust volume to a desired level.Volume is in minimum

Wiring is not properly con-

nected. Check wiring connection.

The operation

k e y s d o n o t

work.

The built-in microcomputer is

not operating properly.

Press the RESET button.

Front panel is not properly xed

into its place.

T h e r a d i o

does not work.

The automatic

radio station

selection does

not work.

The antenna cable is not con-

nected.

Insert the antenna cable rmly.

The signals are too weak. Select a station manually.

General

Power Requirement

Load Impedance

Max. Power Output

Tone Controls

Bass at 100 Hz

Dimensions

Mounting Dimensions

Weight

FM radio

Tuning Range

IF Range

Usable Sensitivity (-30dB)

Signal-to-noise Ratio

Stereo Separation

12V DC (11-16V allowable)

4 Ω

20W x4

±10 dB

Bass at 100 Hz

Treble at 10 kHz

Approx. 188 x 134 x59 mm (d/w/h)

Approx. 169 x 182 x53 mm (d/w/h)

Approx. 0.82 kg

87.5-108 (MHz)

10.7 MHz

15 dBuV

50 dB

25 dB

USB/SD MP3 player

Signal-to-noise Ratio

Separation

Distortion

Frequency Response

60 dB

40 dB

<=1%

40-20000Hz

Note:

Due to continuous product improvement, specifications and design are subject to

change without prior notice.

CAUTION! The unit conforms to the international safety specications and to guide

lines of the European community and also complies with current standards concerning

electrical safety and electromagnetic compatibility EMC.

Volume:

To increase or decrease the sound level, rotate knob (3) clockwise or anti-SEL/VOL

clockwise.

Sound Settings

Repeatedly press knob (3) to select the desired mode in the following order: SEL/ VOL

“BAS” (Bass) -> “TRE” (Treble) -> “BAL” (Balance) -> “FAD“ (Fader) -> “TA VOL“ (TA

volume) ->”REG” (REG ON /OFF) -> “EON” (EON ON/ OFF) -> “LOC” (LOC ON/ OFF)

->STEREO/ MONO -> “VOL” (Volume). After selecting the desired mode, you can

adjust the current level by rotating the knob (3). SEL/ VOL

Note: -The unit will return to the previous mode if no adjusting happens within 3 sec

onds.

-Refer to radio section for and .EON, REG, LOC STEREO/MONO

Preset equalizer

When you are listening to popular, classic or rock music, use the EQ function to adjust

the sound quality. Press (22) to select different equalizer mode:FLAT->POP-> EQ

ROCK->CLASS -> EQ OFF.

Switching Loudness On/Off

Press and hold button (19) until “LOUD ON” shows on display to activate BAND/LOUD

LOUDNESS function. With this function, you increase the low frequency, which can im-

prove sound sensitivity. Press and hold this button again until “LOUD OFF” is displayed

to cancel LOUDNESS function.

SOUND FEATURES

LISTENING TO THE RADIO

Band selection

In tuner mode, repeatedly press button (19) to select bands: FM1->FM2BAND/ LOUD

->FM3.

Station search

- Manual Tuning

Press and hold button or (23/24) until “MANUAL” shows on display, then press

button or (23/24) continuously to select a station downward or upward. Press

and hold button or (23/24) to tune to a station with a faster speed.

Note: The unit will return to the “AUTO” scanning mode if no adjusting happens within

5 seconds.

- Automatic Tuning

Press or (23/24) once, the radio automatically searches a station downward or

upward respectively and plays when it nds a station. Press or (23/24) again to

stop scanning.

BASIC OPERATIONS

Turn on/off the unit

Press button (1) to turn on the unit. Press this button again to turn off the unit.POWER

Current time display

Press button (11) to display the current time when unit is ON. DSP

To set the time:

Press and hold DSP (11) button until clock time with ashing hour digits appears. Then

Press and button to adjust the hour value and press DSP (11) to conrm.

Then minute digits ash. Press and button to adjust the minute value and

press DSP (11) to conrm

Information display

Successive key presses on DSP (11) button.

- In case of receiving a RDS station.

The display will show: CT (Current Time) -> FREQ (Frequency) -> PTY (Program Type)

-> PS (Program Service name)

- In case of receiving a station without RDS

The display will show: CT -> FREQ -> NO PTY -> NO PS

Note: It will return to normal display mode if no key is pressed within 5 seconds.

Mode selection

Press MODE (21) button to select different sourcing mode: Radio→ USB →SD/SDHC/

MMC →AUX

Reset the unit

Operating the unit for the rst time or after replacing the car battery, you must reset the

unit. To set the unit to initial status, press button (8) located on the base with RESET

a pointed object. When some errors occur in display, you can also reset the unit, but it

will erase the clock setting and some memorized functions.

AR-3111 IB MUSE 001 REV0 -GB.ind2 2 7/7/2011 5:03:30 PM

Product specificaties

Merk:	Muse
Categorie:	Autoradio
Model:	M-092 MR
Kleur van het product:	Zwart
Ingebouwd display:	Ja
Gewicht:	360 g
Gewicht verpakking:	820 g
Breedte verpakking:	210 mm
Diepte verpakking:	78 mm
Hoogte verpakking:	180 mm
Ondersteund audioformaat:	MP3
USB-poort:	Ja
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	MicroSD (TransFlash)
Volumeregeling:	Draaiknop
Aantal USB-aansluitingen:	1
FM-radio:	Ja
USB-versie:	2.0
Uitgangsvermogen:	100 W
Display verlichting:	Ja
Kleur van de verlichting:	Wit
Audio-uitgangskanalen:	- kanalen
MP3 afspelen:	Ja
ID3 Tag weergave:	Ja
AUX ingang:	Ja
Ondersteunde frequentiebanden:	FM,PLL
Aantal voorkeurszenders:	18
Afmetingen (B x D x H):	185 x 140 x 58 mm
Inclusief RDS tuner:	Ja
CD-R afspelen:	Nee
CD-RW afspelen:	Nee
Te gebruiken met een iPod:	Nee
Type beeldscherm:	LCD
Kleur toetsenverlichting:	Blauw
Maximaal vermogen per kanaal:	25 W