Moxa AWK-4131-M12-EU-T Handleiding

Moxa Wifi-repeater AWK-4131-M12-EU-T

Lees hieronder de 📖 handleiding in het Nederlandse voor Moxa AWK-4131-M12-EU-T (14 pagina's) in de categorie Wifi-repeater. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/14

 . A2010 Moxa Inc ll rights reserved.

Reproduction without permission is prohibited.

P/N: 1802041310010

AWK-4131 Hardware

Installation Guide

Moxa AirWorks

First Edition, March 2011

- - 2

Notes for the Reader

WARNING

Indicates that death or personal injury may occur if proper

precautions are not taken.

ATTENTION

Indicates that possible damage to this product or your property

may result if proper precautions are not taken.

NOTE

H ighlights important information related to this product.

Package Checklist

Moxa’s AWK- 4131 is shipped with the following items. If any of these

items is missing or damaged, please contact your customer service

representative for assistance.

• AWK- 4131

• 2 omni- - directional antennas (5/2 dBi, N type male, 2.4/5 GHz)

• Wall mounting kit

• Field- installable power plug

• Field- - installable M12 8 pin male plug for Ethernet

• Metal cap to cover M12 male DI/O connector

• Metal cap to cover RJ45 connector

• Meta cap to cover M30 SFP connector

• Documentation and software CD

• Quick installation guide (printed)

• Warranty card

Recommended SFP Accessories

SFP-1G series

• SFP- 1GSXLC:

Small form factor pluggable transceiver with 1000BaseSX, LC, 0.5 km,

0 to 60°C

• SFP- - 1GSXLC T:

Small form factor pluggable transceiver with 1000BaseSX, LC, 0.5 km,

- 20 to 75°C

• SFP- 1GLSXLC:

Small form factor pluggable transceiver with 1000BaseLSX, LC, 2 km,

0 to 60°C

• SFP- - 1GLSXLC T:

Small form factor pluggable transceiver with 1000BaseLSX, LC, 2 km,

- 40 to 85°C

• SFP- 1GLXLC:

Small form factor pluggable transceiver with 1000BaseLX, LC, 10 km,

0 to 60°C

- - 3

• SFP- - 1GLXLC T:

Small form factor pluggable transceiver with 1000BaseLX, LC, 10 km,

- 40 to 85°C

• SFP- 1GLHLC:

Small form factor pluggable transceiver with 1000BaseLH, LC, 30 km,

0 to 60°C

• SFP- - 1GLHLC T:

Small form factor pluggable transceiver with 1000BaseLH, LC, 30 km,

- 40 to 85°C

• SFP- 1GLHXLC:

Small form factor pluggable transceiver with 1000BaseLHX, LC, 40

km, 0 to 60°C

• SFP- - 1GLHXLC T:

Small form factor pluggable transceiver with 1000BaseLHX, LC, 40

km, - 40 to 85°C

• SFP- 1GZXLC:

Small form factor pluggable transceiver with 1000BaseZX, LC, 80 km,

0 to 60°C

• SFP- - 1GZXLC T:

Small form factor pluggable transceiver with 1000BaseZX, LC, 80 km,

- 40 to 85°C

• SFP- 1GEZXLC:

Small form factor pluggable transceiver with 1000BaseEZX, LC, 110

km, 0 to 60°C

• SFP- - 1GEZXLC 120:

Small form factor pluggable transceiver with 1000BaseEZX, LC, 120

km, 0 to 60°C

NOTE

The above items come with the AWK- 4131

standard version. The

package contents for customized versions may different.be

Installation

Before installing the AWK-4131, make sure that all items in the Package

Checklist are in the box. In addition, you will need access to a notebook

computer or PC equipped with an Ethernet port. The AWK- 4131 has a

default IP address, user name and password that you must use when

resetting or connecting to your AWK- 4131 device.

Default IP address: 192.168.127.253

User name: admin

Password: root

Please read “Chapter2 Getting Started” in AWK- 4131 User’s Manual for

more details about installation and configuration.

ATTENTION

For security reasons, we strongly recommend changing the

password. To do so, go to Maintenance





Password

, and then

follow the on- screen instructions.

- - 4

NOTE

To make the change effective, you must save the change and

then click Restart





Save and Restart button to apply all

changes.

Panel Layout of the AWK- 4131

1. Main antenna A.

2. Main antenna B.

3. LEDs for PWR, FAULT,

STATE, WLAN and LAN.

4. M12 A-coding connector

for PWR1 and PWR2.

5. M12 8- pin male

connector

for DI/DO

6. M12 8-pin female

connector for Ethernet

port

7. SFP Port

8. RS- . 232 console port

9. Reset button

10. Screw holes for wall

mounting

11. Waterproof vent

12. Grounding screw

13. rail Screw holes for -DIN

mounting

ATTENTION

Please DO NOT open or remove the vent 11

. The warranty will be

invalid if the seal is removed.

All exposed connectors, including 1, 2, 4 - 9, should be tightly

covered by suitable caps when they are not in use.

- - 5

Dimensions (unit = mm)

Attaching Antennas

The AWK directional antenna by - - -4131 inclues two dual band omni

default. Attach the antennas as illustrated below.

Step 1: -Use your fingers and hold the antenna metal N type connector.

Step 2: Screw the antenna N- -type connector (male) onto the AWK 4131

device’s N-type connector (female)

Caution

Do not hold the rubber plate to screw the antenna on to the

AWK- 4131 device.

ATTENTION

Use the antennas correctly: Use 2.4GHz antennas if the

AWK /n- 4131 operates in IEEE 802.11b/g . Use the 5GHz

antennas for operations in IEEE802.11a.

Make sure your antenna

instal

lation is within a safe area covered by a lightning protection

or surge arrest system.

Wall Mounting

In most applications, wall mount provides an easier installation. You will

find it quite easy to mount AWK- 4131 on the wall, as illustrated below.

Antenna Metal N- type

Rubber plate

- - 6

STEP 1:

Attach the wall-mounting kit

with M4 screws, as shown in

the diagram below.

STEP 2:

Mounting the AWK- 4131 on the wall

requires 4 screws. Use the AWK- 4131

device, with wall-mounting kit

attached, as a guide to mark the correct

locations of the 4 screws. The heads of

the screws are recommended to be

between 5.5mm and 8.5 mm in

diameter, and the shafts should not

more than 5.0 mm

in diameter, as

shown in the figure.

Do not screw the screws all the way in to the wall leave a space of about —

2 mm to allow room for sliding the wall-mounting kit between the wall and

the screws.

ATTENTION

You can test the screw head and shank

size by inserting the screw

into one of the keyhole shaped apertures of the wall mounting

plates before it is screwed into the wall.

STEP 3:

Once the screws are fixed into the wall, insert the four screw heads

through the large opening of the shaped apertures, and then keyhole-

slide the AWK-4131 downwards, as indicated to the right. Tighten the

four screws for added stability.

ATTENTION

To avoid environmental vibration or shock, you can consider a

robust installation with four bigger screws, which the shafts are

between 7.0 mm and 8.5 mm in diameter, and fix the AWK-4131

onto wall directly and tightly.

- - 7

DIN- Rail Mounting (Optional)

The DK- -DC50131 die cast metal kit can be

bought separately, and enable easy and

robust installation for the AWK- . 4131

A pair

of DK- -DC50131s is needed for DIN Rail

mounting. To install the DIN-Rail mounting

kits, tightly attach the two DIN-Rail

mounting kits on the rear panel of AWK-4131

with 12 screws. (6 screws for each kit)

To Install

STEP 1:

Use the recessed button

on the spring-loaded

bracket to lock it into

position.

STEP 2:

Insert the top of the DIN-Rail into the slot

just below the upper hook of the DIN-Rail

mounting kit. Push the AWK- 4131 toward

the DIN-Rail until -the DIN Rail attachment

bracket snaps into place.

To Release

STEP 1:

Pull out the two spring-loaded

brackets from the bottom until

they are fixed in the “release”

position.

STEP 2:

Pull the AWK-4131 out and upward.

- - 8

Wiring Requirements

WARNING Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa AWK- . 4131

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size. If the current goes

above the maximum ratings, the wiring could overheat, causing

serious damage to your equipment.

You should also pay attention to the following items:

• Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

• You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

• Keep input wiring and output wiring separate.

• It is strongly advised that you label wiring to all devices in the system

when necessary.

Grounding Moxa AWK- 4131

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface, such as a metal panel. There must be no

potential difference between two ground potentials, otherwise

there is a risk that the device could be destroyed.

Wiring the Redundant Power Inputs

The AWK over- -4131 must be connected to a power -Ethernet (PoE) IEEE

802.3af compliant power source or an IEC60950 compliant limited power

source. When AWK- 4131 is powered via DC power, the M12 A-coding

connector on the bottom panel is used for the AWK ’s two redundant -4131

inputs. The pin assignment is shown below:

Pin Power Input

1 V1+

2 V2+

3 - V1

4 - V2

5 GND

- - 9

ATTENTION

This product is intended to be supplied by a Listed Power Unit

marked “Class 2” or “LPS” and rated O/P: 12 to 48 VDC, minimum

6 W (12 V/0.494 A to 48V/0.121 A, 25°C).

Make sure External Power Adaptor (includes power cords and

plug assemblies) provided with the unit is certified and suitable

for use in your country.

Before connecting the AWK-

4131 to the DC power inputs, make

sure the DC power source voltage is stable.

ATTENTION

Do not use the an PoE Injector. Instead, please use

IEEE802.3af

or IEEE802.3at compliant PSE (Power Sourcing Equipment) for

PoE (Power over Ethernet) . device

Wiring the Digital Inputs and Relay Contact

(Digital Output)

The AWK DI1 and DI2. Each DI - —4131 has two sets of digital input

comprises two contacts of the 8-pin M12 connector on the AWK-4131’s

bottom panel. These two digital inputs can be connected to

digital- - - output enabled sensors for on site status monitoring.

The AWK also has one relay output, which consists of the two - 4131

contacts. These relay contacts are used to detect user configured events. -

The two wires attached to the Relay contacts form an open circuit when a

user- -configured event is triggered. If a user configured event does not

occur, the Relay circuit will be closed.

A field installable plug, - M12A 8P- F- 7IP6 , is recommended for

connecting the AWK-4131’s DIs and relay.

Pin Signal

1 Relay

3 DI1 I1

4 DI1 COM_1

5 DI2 I2

6 DI2 COM_2

7 Reserved

- - 10

Communication Connections

Connecting the Data Lines

10/100/1000BaseT(X) Ethernet Port Connection

AWK- 4131 has 10/100/1000BaseT(X) Ethernet ports (8-pin shielded M12

connector with A coding). The 10/100/1000BaseT(X) ports located on the

AWK- 3 -41 1’s bottom panel are used to connect to Ethernet enabled

devices. Below we show pinouts for both MDI (NIC- -type) ports and MDI X

(HUB/Switch- type) ports.

Pinouts for the 10/100/1000BaseT(X) M12 (8- pin) Port

ATTENTION

To ensure the IP6 rated connectivity, you must use a 8-

waterproof housing during any communication activities. An

IP68- -rated field installable plug, which is attached in AWK 4131

’s

accessory pack, may be needed in this case. The installation

guide is shown below:

Ethernet M12 Plug

Dimensions (unit: mm)

Product specificaties

Merk:	Moxa
Categorie:	Wifi-repeater
Model:	AWK-4131-M12-EU-T
Gewicht:	1800 g
Stroomvoorziening:	24 VDC
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Draadloos
Frequentieband:	2.412 - 2.472, 5.18 - 5.24 GHz
Aansluiting voor netstroomadapter:	Ja
Modulatie:	16-QAM, 64-QAM, BPSK, CCK, DBPSK, DQPSK, DSSS, OFDM, QPSK
Netwerkstandaard:	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Ondersteunde beveiligingsalgoritmen:	WEP, WPA, WPA2
Temperatuur bij opslag:	-40 - 85 °C
Power LED:	Ja
MAC adres filtering:	Ja
DHCP server:	Ja
Veiligheid:	UL 60950-1, EN 60950-1
Bedrijfstemperatuur, bereik:	-40 - 167 °F
Aansluiting antenne:	N-type
Mean time between failures (MTBF):	367406 uur
Maximale overdrachtssnelheid van gegevens:	300 Mbit/s
DHCP client:	Ja
Power over Ethernet (PoE):	Ja
Ondersteunde protocollen:	Proxy ARP, DNS, HTTP, HTTPS, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, PPPoE, DHCP
Afmetingen (B x D x H):	224 x 147.7 x 64.5 mm
Full duplex:	Ja
Bedrijfstemperatuur (T-T):	-40 - 75 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 100 procent
Connectivity LEDs:	Ja