Mitsubishi fl6900u Handleiding
Mitsubishi
Beamer
fl6900u
Lees hieronder de 📖 handleiding in het Nederlandse voor Mitsubishi fl6900u (48 pagina's) in de categorie Beamer. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/48

FL6900
LCD PROJECTOR
MODEL
FL6900U
User Manual
This User Manual is important to you.
Please read it before using your projector.

EN-2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning fl ash with arrowhead symbol within an equilateral triangle is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of suffi cient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE
EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specifi ed power supply cord. If
you use another power supply cord, it may cause
interference with radio and television reception.
Use the attached RGB cable and RS-232C cable and
the shielded LAN cable with this equipment so as to
keep interference within the limits of a FCC Class B
device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS WHEN
THE PROJECTOR IS IN THE POWER ON MODE.
CAUTION
Not for use in a computer room as defi ned in the
Standard for the Protection of Electronic Computer/
Data Processing Equipment, ANSI/NFPA 75.
When using the projector in Europe:
COMPLIANCE NOTICE
This projector complies with the requirements of
the EC Directive 2004/108/EC “EMC Directive” and
2006/95/EC “Low Voltage Directive”.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside of
the buildings. All places of operation are characterised
by their connection to the public low voltage power
supply system.
WARNING
Use the attached RGB cable and RS-232C cable and
the shielded LAN cable with this equipment so as to
keep interference within the limits of an EN55022 Class
B device.
Please follow WARNING instructions.

EN-3
Contents
Important safeguards ........................................................................................................................4
Preparing your projector ....................................................................................................................6
Using the remote control ...................................................................................................................9
Setting up your projector .................................................................................................................10
Viewing computer images ...............................................................................................................13
Viewing video images ......................................................................................................................17
Menu operation ...............................................................................................................................22
Adjusting projected images .............................................................................................................28
Advanced features ..........................................................................................................................32
Indicators .........................................................................................................................................37
Terminal cover (with anti-theft alarm device) ...................................................................................38
Replacing the lamp .........................................................................................................................39
Maintenance ....................................................................................................................................41
Troubleshooting ...............................................................................................................................42
Specifi cations ..................................................................................................................................45
Trademark, Registered trademark
• The trademark of PJLink is trademark applied for registration or registered trademark in Japan, the United States,
and other countries and areas.
• Other brand or product names are trademarks or registered trademarks of their respective holders.
Note: This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/EC Article 10 Information
for users and Annex IV, and/or to the directive 2006/66/EC Article 20 Information
for end-users and Annex II.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components
which can be recycled and/or reused.
This symbol means that electrical and electronic equipment, batteries and accumulators, at their end-of-life, should
be disposed of separately from your household waste.
If a chemical symbol is printed beneath the symbol shown above, this chemical symbol means that the battery or
accumulator contains a heavy metal at a certain concentration. This will be indicated as follows:
Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)
In the European Union there are separate collection systems for used electrical and electronic products, batteries and
accumulators.
Please, dispose of this equipment, batteries and accumulators correctly at your local community waste collection/
recycling centre.
Please, help us to conserve the environment we live in!
Declaration of Conformity
Model number: FL6900U
Trade name: MITSUBISHI ELECTRIC
Responsible party: Mitsubishi Digital Electronics America, Inc.
9351 Jeronimo Road, Irvine, CA 92618 U.S.A
Telephone number: +1-(949) 465-6000
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

EN-5
WARNING:
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fi re or electric shock.
In this case, unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock. Except
as specifi cally explained in the User Manual do not attempt
to service this product by yourself. Please contact your
dealer when you want to fi x, adjust or inspect the projector.
Do not modify this equipment.
It can lead to fi re or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged,
unplug the projector and contact your dealer for
inspection. It may lead to fi re if you keep using the
damaged projector.
Do not face the projector lens to the sun.
It can lead to fi re.
Use correct voltage.
If you use incorrect voltage, it can lead to fi re.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface only.
Please do not place equipment on unstable surfaces.
Do not look into the lens when it is operating.
It may hurt your eyes. Never let children look into the
lens when it is on.
Do not turn off the main power abruptly or
unplug the projector during operation.
It can lead to lamp breakage, fi re, electric shock or
other trouble. It is best to wait for the fan to turn off
before turning the main power off.
Do not touch the air outlet grille and bottom
plate, which become hot.
Do not touch them or put other equipment in front
of the air outlet grille. The air outlet grille and bottom
plate, when heated, may cause injury or damage to
other equipment. Also, do not set the projector on the
desk which is easily affected by heat.
Clean the air-fi lter once a month.
Clean the air-fi lter frequently. If the fi lter or ventilation
slots become clogged with dirt or dust, the
temperature inside of the projector may rise and cause
some troubles, such as damage of inside parts, and
shortening the life of panel.
Do not look into the air outlet grille when
projector is operating.
Heat, dust, etc. may blow out of it and hurt your eyes.
Do not insert your fi ngers in the space
between the lens and the cabinet.
The lens may shift causing injury or damage to the
projector.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality
and fi re.
Do not use fl ammable solvents (benzene,
thinner, etc.) and fl ammable aerosols near the
projector.
Flammable substances may ignite causing fi re or
breakdown because the temperature inside the
projector rises very high while the lamp is illuminating.
Do not use the projector with condensation on it.
It can lead to breakdown or other failure.
Place of installation
For safety’s sake, refrain from setting the projector
at any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specifi ed below.
• Operating temperature: between +41°F (+5°C) and
+104°F (+40°C)
• Operating humidity: between 30% and 90%
• Never put any heat-producing device under the
projector so that the projector does not overheat.
• Do not attach the projector to a place that is
unstable or subjected to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic fi eld. Also refrain from
installing near the projector any cable carrying a
large current.
• Place the projector on a solid, vibration free surface;
otherwise it may fall, causing serious injury to a
child or adult, and serious damage to the product.
• Do not stand the projector; it may fall, causing
serious injury and damage to the projector.
• Slanting the projector more than ±10°(right and
left) or ±15°(front and rear) may cause trouble or
explosion of the lamp.
• Do not place the projector near air-conditioning
unit, heater, or humidifi er to avoid hot or moist air to
the exhaust and ventilation hole of the projector.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
Changes or modifi cations not expressly approved by Mitsubishi could void the user’s authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
Important safeguards (continued)

EN-6
Preparing your projector
1
2
3
Checking accessories
The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in
the package.
Important:
• The attached power cords are to be used exclusively for this product. Never use them for other products.
Inserting the batteries into the remote control
1. Remove the rear lid of the remote control.
2. Check the polarity (+), (-) of the batteries, and set them
correctly, inserting their (-) side fi rst.
• If the battery is inserted from the (+) side fi rst, inserting
the (-) side is diffi cult because the coil spring end hits on
the battery side. If the battery is forced to insert in this
way, the outer label of the battery may get ripped and it
may cause a short-circuit and heating.
3. Attach the rear lid.
Important:
• Use two size-AA batteries (LR6).
• Replace the 2 batteries with new ones when the remote
control is slow to operate.
Removing the batteries from the remote control
Remove the back lid of the remote control and take out the
batteries.
Caution:
• Use of a battery of wrong type may cause explosion.
• Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
• Dispose of used batteries according to your local regulations.
• Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fi re.
• Be sure to handle the batteries according to the instructions.
• Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
• Keep batteries out of reach of children and pets.
• Remove the batteries, if the remote control is not used for a long time.
• Do not combine a new battery with an old one.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in
contact with your eyes, rinse them with water and then consult your doctor.
Cables
Remote control parts Terminal cover parts
Remote control
(290P136-40)
LR6 (size-AA)
battery (two)
Terminal cover (with anti-theft alarm device)
(750A657-10)
Safety pin (two)
(450D057-10)
Sticker for anti-theft
alarm (853C588-10)
RS-232C cable
(246C598-10)
DVI-HDMI
conversion cable
(242P033-10)
LR6 (size-AA)
battery (two)
RGB cable for PC
(246C597-10)
Audio/Video cable
(246C381-10)
Others
• Lens cap (attached
to the projector)
• Air-filter
(620D119-10)
• CD-ROM
(919C132-70)
• Safety Manual/
Quick Start up
(871D389-70)
Mini D-SUB
15-pin
Mini D-SUB
15-pin
D-SUB
9-pin
Power supply parts
Power cord (two)
(246C483-10, 246C383-20)
• Used for projector control
by computer.
D-SUB
9-pin HDMI
DVI
HDMI

EN-7
Overview
1 2
8
4 5
9 10
6 7
3
8
7
10
9
11
1
3
4
6
5
2
1 Remote control sensor (Front)
2 Lens
3 Control area
4 Easy-carry handle
5 Air inlet grille
6 Terminal board
7 Air outlet grille
Control area
1 POWER button
2 AUTO POSITION/S button
3 COMPUTER/W button
4 VOLUME/T button
5 MENU button
6 ZOOM/FOCUS button
7 STATUS indicator
8 POWER indicator
9 VIDEO/X button
10 ENTER/KEYSTONE button
11 LENS SHIFT button
1 2
7
8
9 111210 13 14 15
3 4 5 6 1 REMOTE IN and OUT terminals
2 LAN terminal
3 SERIAL terminal (D-SUB 9-pin)
4 USB (COMPUTER) terminal
5 COMPUTER/COMPONENT VIDEO DVI-D (HDCP) termi-
nal (DVI-D 24-pin)
6 COMPUTER/COMPONENT VIDEO IN 1 terminals (R/PR,
G/Y, B/P , H/HV, V) (BNC)B
7 AUDIO IN 1 terminal (Mini jack)
• The AUDIO IN 1 terminal is used for both COMPUTER 1
and DVI input.
8 AUDIO IN 2 terminal (Mini jack)
9 Main power switch
O : OFF I : ON
10 Power jack
11 COMPUTER/COMPONENT VIDEO IN 2 terminal (Mini
D-SUB 15-pin)
12 MONITOR OUT terminal (Mini D-SUB 15-pin)
13 AUDIO OUT terminal (Mini jack)
14 VIDEO IN and audio input terminals
15 S-VIDEO IN and audio input terminals
Terminal board
Preparating your projector (continued)
8 Speaker
9 Remote control sensor (Rear)
10 Kensington Security Lock Standard connector

EN-8
1
2
3
Preparating your projector (continued)
Bottom side
1 Adjustment feet
2 Air inlet grille/Filter cover
3 Lamp cover
Caution:
Do not replace the lamp immediately after using the
projector because the lamp would be extremely hot
and it may cause burns.
Remote control 1 Laser aperture
2 Transmission window
3 Wired remote control jack
4 Indicator
5 POWER button
6 VIDEO button
7 DVI-D(HDCP) button
8 HOME button
9 END button
10 Page Up and Page Down buttons
11 Mouse pointer
12 LENS SHIFT button
13 MENU button
14 ZOOM/FOCUS button
15 + , - (VOLUME) buttons
16 COLOR ENHANCER (CE) button
17 COMPUTER 1, 2 buttons
18 S-VIDEO button
19 AUTO POSITION button
20 LASER button
21 buttonsS T W X, , ,
22 R-CLICK button
23 ENTER button
24 KEYSTONE button
25 ASPECT button
26 SPLIT button
27 FREEZE button
28 AV MUTE button
29 Left click button
• Pressing the LASER button emits a laser beam.
Even when you keep holding down the LASER but-
ton, it is emitted only one minute. To keep emitting
it longer, press the LASER button again.
• You can disable the LASER button to prevent laser
radiation due to misuse of the button.
How to disable the LASER button
While holding the LASER button down, press the T
button 3 times.
How to enable the LASER button
While holding the LASER button down, press the S
button 3 times.
• Whenever the batteries are replaced, the LASER
button is enabled.
About the laser beam
This remote control is a Class 2 laser product. (Max. output: 1 mW, Wavelength: 620-640 nm)
Beam Divergence: 6 m distance about 10.0 mm x 10.0 mm (±6.0 mm)
Caution:
• Pressing the LASER button on the remote control emits a laser beam. Do not look into the laser beam directly. Do
not point the laser beam at anyone. Looking at the laser beam directly may damage eyesight.
• Use of controls or adjustments or procedures other than those specifi ed herein may result in hazardous radiation exposure.
• This remote controller cannot be repaired.
29
COMPUTER
VIDEO S-VIDEO
DVI-D(HDCP)
HOME Page Up
END Page Down
AUTO POSITION
KEYST ONE
ASPECT
SPLIT
FREEZEAV MUTE
LENS SHIFTZO OM / FOCUS
1 2
VOLUME
17
18
19
21
22
23
24
25
27
28
20
26
CE
MENU ENT ER
LASER
R-CLICK
1
3
4
5
6
7
8
9
11
12
13
14
15
10
16
2
There are 2 types of labels placed on the back of the
remote control and either of them is placed on it.
or

EN-9
Using the remote control
30°30° 30°30°
20°
10°
20°
10°
20°
20°
Operational range of the remote control
• Keep the remote control photo-sensor out of direct
sunlight or fl uorescent lamp light.
• Keep the remote control photo-sensor at least 2 m (6
feet) away from fl uorescent lamps. Otherwise, the
remote control may malfunction.
• If there is an inverter-operated fl uorescent lamp
near the remote control, the remote control opera-
tion may become unstable.
• When you use the remote control too close to the
remote control sensor, the remote control may not
work correctly.
Reception angle
Vertical directions
Vertical directions (ceiling mount)
Front of projector Rear of projector
Operate the remote control
within a distance of 10 m
(30 feet) from the projector,
pointing the light beam at
the remote control photo-
sensor (front or rear) of the
projector.
When operating the remote control, keep the distance
from the remote control to the projector via the
screen within about 5 m (15 feet). The operable range
of the remote control, however, depends on the
characteristics of the screen.
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired
remote control is useful for operating in a distance or outside of the operating area.
• For connection, use the pin-pin cable of ø3.5 stereo
type, which is commercially available. However,
some cable may not work correctly.
• When REMOTE OUT terminal on this projector is
connected to the REMOTE IN terminal on the other
projector, the two projectors can be controlled
together by using the remote control. (Up to two
projectors can be controlled.)
• When the remote control is connected with remote
control cable, it does not work as a wireless remote
control.
• When using the wired remote control, the laser
beam may be darker. It is normal.
REMOTE IN
REMOTE OUT
REMOTE IN

EN-10
Setting up your projector
Setting up the screen
Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the
projection angle of the projector. (See page 11.)
• Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of
the screen center.
• Do not install the screen where it is exposed to direct sunlight or lighting. Light directly refl ecting on the screen
makes the projected images whitish and hard to view.
Screen size and projection distance
Refer to the following table to determine the screen size and projection distance.
W1
H1 H2H
L
W1
W
L
W1
H1H2 H
L
W1
W
L
• You are recommended to install the projector as close to the screen as possible within the specified projection
distance range for your screen size.
• Depending on the installation conditions, warm air that is emitted from the exhaust vents may fl ow into the intake
vent, causing the projector to display “TEMPERATURE!!” and then stop projecting images.
When the aspect ratio of the screen is 16:9
Screen size Projection distance (L) Lens movable range
Diagonal size Height (H) Width (W)
Shortest (Wide)
Longest (Tele)
H1 H2 W1
inch cm inch cm inch cm inch m inch m inch cm inch cm inch cm
60 152 29 75 52 133 104 2.6 133 3.4 15 38 4 10 3 7
80 203 39 100 70 177 140 3.5 178 4.5 20 51 5 13 4 9
100 254 49 125 87 221 175 4.5 223 5.7 25 63 7 17 4 11
150 381 74 187 131 332 264 6.7 336 8.5 37 94 10 25 7 17
200 508 98 249 174 443 354 9.0 449 11.4 49 125 13 34 9 22
250 635 123 311 218 553 443 11.2 - - 62 156 17 42 11 28
The above fi gures are approximate and may be slightly different from the actual measurements.•
When the aspect ratio of the screen is 4:3
When the aspect ratio of the screen is 4:3, the positional relation
between the projected image and the screen is as shown on the right.
Refer to the following table for installation.
When the aspect ratio of the image is 16:9
Screen size (4:3)
Size of the projected image (16:9)
Black
space (B)
Projection distance (L) Lens movable range
Diagonal size Height (SH) Width (W) Height (H) Width (W)
Shortest (Wide)
Longest (Tele)
H1 H2 W1
inch cm inch cm inch cm inch cm inch cm inch cm inch m inch m inch cm inch cm inch cm
60 152 36 91 48 122 27 69 48 122 5 11 95 2.4 121 3.1 14 35 4 9 2 6
80 203 48 122 64 163 36 91 64 163 6 15 128 3.2 163 4.1 18 46 5 12 3 8
100 254 60 152 80 203 45 114 80 203 8 19 161 4.1 204 5.2 23 58 6 15 4 10
150 381 90 229 120 305 68 171 120 305 11 29 243 6.2 308 7.8 34 86 9 23 6 15
200 508 120 305 160 406 90 229 160 406 15 38 324 8.2 412 10.5 45 115 12 31 8 20
250 635 150 381 200 508 113 286 200 508 19 48 406 10.3 - - 57 144 15 39 10 26
The above fi gures are approximate and may be slightly different from the actual measurements.•
B BH
SH
W
Front projection Front projection, ceiling mounting

EN-13
Viewing computer images
2
1
AUDIO OUT
AUDIO IN 1/2
2
1
2
1
A. Connecting the projector to a computer
Preparation:
• Make sure that the power of the projector and that of the computer are turned off.
• When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor.
For analog connection:
(For using the COMPUTER/COMPONENT VIDEO IN 2
terminal.)
1. Connect one end of the supplied RGB cable to the
COMPUTER/COMPONENT VIDEO IN 2 terminal of the
projector.
2. Connect the other end of the RGB cable to the monitor
port of the computer.
• When viewing images supplied from an analog-connected
computer, press the COMPUTER 2 button on the remote
control.
For analog connection:
(For using the COMPUTER/COMPONENT VIDEO IN 1
terminal.)
1. Connect one end of a commercially available BNC cable to
the COMPUTER/COMPONENT VIDEO IN 1 terminal of the
projector.
2. Connect the other end of the BNC cable to the 5 BNC
terminals of the monitor port of the computer.
• When viewing images supplied from an analog-connected
computer, press the COMPUTER 1 button on the remote
control.
For digital connection:
1. Connect one end of a commercially available DVI cable
to the COMPUTER/COMPONENT VIDEO DVI-D(HDCP)
terminal of the projector.
2. Connect the other end of the DVI cable to the DVI terminal
of the computer.
• When viewing images supplied from a digital-connected
computer, press the DVI-D(HDCP) button on the remote
control.
• Turn on the main power switch of the projector before
starting the computer.
For audio connection:
1. Connect one end of a commercially available PC audio
cable to the AUDIO IN 1/2 terminal of the projector.
2. Connect the other end of the PC audio cable to the audio
output terminal of the computer.
• This projector uses stereo pin jack for its audio input. Check
the type of the audio output terminal of the connected
computer and prepare a proper cable for connection. Some
computers don’t have the audio output terminal.
• Speaker output is mono.
COMPUTER/
COMPONENT
VIDEO IN 2
COMPUTER/
COMPONENT
VIDEO DVI-D(HDCP)
To monitor port
RGB cable
DVI cable (option)
To DVI
Computer
PC audio cable (option) To audio output
terminal
2
1
R/PR BG/Y B/P H/HV V
V H/HV B/PB RG/Y R/P
COMPUTER/
COMPONENT
VIDEO IN 1
• Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending
on the type of the computer to be connected.
• Use of a long cable may decrease the quality of projected images.
• Images may not be projected correctly, depending on the type of the connected computer.
• When DVI-D signal is input, some signal setting menus are unavailable.
• Also read the instruction manual of the equipment to be connected.
• Contact your dealer for details of connection.
T
o monitor
port (5 BNC)
Computer
Computer
Computer
BNC cable (option)

EN-16
Viewing computer images (continued)
Important:
• Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
• When a 4:3 image is kept displayed for a long time before displaying 16:9 image, the afterimages of the black bars
may appear on the 16:9 image screen. (See page 43.)
To stop projecting:
13. Press the POWER button.
• A confi rmation message is displayed.
• To cancel the procedure, leave the projector for a while or press any button except the POWER button.
14. Press the POWER button again.
• The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator
blinks green.
15. Wait about 2 minutes for the STATUS indicator to be turned off.
• During this period of 2 minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.
• The air outlet fans rotate faster as the temperature around the projector rises.
• Do not turn off the main power switch or unplug the power cord while the STATUS indicator is blinking. Turning
off the main power switch or unplugging the power cord immediately after use may cause a breakdown.
• Though the fans make loud sounds during cooling, such symptom is not a malfunction.
16. Turn off the main power switch.
• The POWER indicator will go out.
• If the main power switch should be turned off or the power cord should be unplugged accidentally while either
the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10
minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn’t light up im-
mediately, repeat pressing the POWER button 2 or 3 times. If it should still fail to light up, replace the lamp.
• Cover the lens with the lens cap to protect it from dust.
• For safety’s sake, unplug the power cord from the outlet.
• When you repeat turning off the main switch within 30 minutes from the lamp illumination, an error may occur
in the clock function of this product.
AV mute
The video and audio signals are temporarily muted when the AV MUTE button is pressed. To cancel muting, press the
AV MUTE button again.
• It takes several seconds before muting is completely canceled.
• If MUTE MODE in the INSTALLATION menu is set to IMAGE, the splash screen will appear when the AV MUTE
button is pressed.
• You can alter the splash screen optionally. See page 32.
• The audio from the AUDIO OUT terminal is also muted by pressing the AV MUTE button.
AUTO POSITION button
When the image supplied from the computer is displaced, carry out the following procedure.
1. Project a bright image containing as many texts and characters as possible.
2. When the screen saver has been enabled, disable it.
3. Press the AUTO POSITION button.
The projector automatically makes optimum positional settings for the input signal.
• When you press the AUTO POSITION button while a signal from a video device (or signal marked with *2 on
page 46) is being input, a window to select either of the following two adjustment modes is displayed.
- AUTO ADJUST:
Suitable for signals supplied from a computer.
- VIDEO SIGNAL:
Suitable for signals supplied from a video device such as DVD.
(When you select this mode, the adjustment using the RESOLUTION (MEMORIZE) menu (page 26) becomes
unavailable.)
Select an appropriate mode using the or button and then press the ENTER button.W X
• If the projected image is still displaced even after pressing the AUTO POSITION button several times, refer to
the procedure to adjust computer images. (See pages 30 and 31.)
• When you carry out this procedure with a dark image, the image may be displaced.
When connecting to a notebook computer:
When the projector is connected to a notebook computer, images may not be projected in some cases. In such
cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type
of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of
the computer you use.)
Setting of the resolution
If the resolution of the computer doesn’t match with that of the projector, projected images may be obscured. Ensure
that their resolutions are the same (see page 46). For the method to change the output resolution of the computer,
contact the manufacturer of the computer.

EN-17
Viewing video images
Connecting to a video player, etc.
1. Connect one end (yellow) of the supplied audio/video cable
to the VIDEO IN terminal of the projector.
2. Connect one end (white and red) of the supplied audio/
video cable to the audio input terminals (L/MONO, R) of the
projector.
3. Connect the other end (yellow) of the audio/video cable to
the video output terminal of the video equipment.
4. Connect the other end (white and red) of the audio/video
cable to the audio output terminals (L, R) of the video
equipment.
When the video equipment is equipped with the S-video
output terminal, make the connection as follows:
1. Connect one end of a commercially available S-video cable
to the S-VIDEO IN terminal of the projector.
2. Connect the other end of the S-video cable to the S-video
output terminal of the video equipment.
3. Connect one end (white and red) of the supplied audio/
video cable to the audio input terminals (L/MONO, R) of the
projector.
4. Connect the other end (white and red) of the audio/video
cable to the audio output terminals (L, R) of the video
equipment.
When using the BNC connector:
(For VIDEO input)
• When the video output terminal of the connected video
equipment is BNC type, use the VIDEO IN terminal (BNC
type).
• Select VIDEO as the input source.
• When using the VIDEO IN terminal (BNC type) and the
VIDEO IN terminal (RCA type) at the same time, the video
signal input to the VIDEO IN terminal (RCA type) takes
priority.
When using the BNC connector:
(For S-VIDEO input)
• When the video output terminals of the connected video
equipment are BNC (Y/C) type, connect Y and C to the
S-VIDEO IN (Y and C) terminals (BNC type) respectively.
• Select S-VIDEO as the input source.
• When using the S-VIDEO IN (Y and C) terminals (BNC type)
and the S-VIDEO IN terminal (S type) at the same time, the
video signal input to the S-VIDEO IN terminal (S type) takes
priority.
• When connecting a monophonic video device, use the white (L) terminal to connect the audio cable. (The same
audio signal is output from the channels L and R of the AUDIO OUT terminal.)
• Also read the instruction manual of the equipment to be connected.
• Contact your dealer for details of connection.
When a TV tuner or VCR is connected:
When you use this projector with a TV tuner or VCR connected, no image may appear or a message of “NO SIGNAL”
may appear on the screen when you change the channel via any channel that is not being received. In such a case,
set the channels of the TV tuner or VCR again. To avoid such symptom, use the TV tuner or VCR with its channel skip
function (that is a function not to display channels that are not being received) enabled.
A. Connecting the projector to video equipment
Preparation:
• Make sure that the power of the projector and that of the video equipment are turned off.
3
4
12
1
3
4
2
To VIDEO
IN terminal
To video
output
terminal
Video player, or the like
To S-VIDEO
IN terminal
S-video cable (option)
To S-video
output
terminal
Video player, or the like
Audio/video
cable
To audio input
terminals
To audio
output
terminals
To audio
input
terminals Audio/video
cable
To audio
output
terminals
To VIDEO
IN terminal
(BNC)
BNC cable (option)
To video
output
terminal
Video player, or the like
To S-VIDEO IN
(Y and C) terminals
(BNC)
BNC cable (option)
To S-video (Y/C)
output terminals
Video player, or the like

EN-18
Connecting to video equipment having a HDMI terminal or DVI-D terminal
You can project high-quality images by connecting the COMPUTER/COMPONENT VIDEO DVI-D (HDCP) terminal of
this projector to video equipment having a HDMI output terminal or DVI-D terminal. In addition, this projector supports
HDCP and is able to receive encrypted digital video data that are output from DVD players.
• HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital
video data for the purpose of copy protection.
• HDMI (High-Defi nition Multimedia Interface) is fully backward compatible with computers, displays and consumer
electronics devices incorporating the DVI standards.
• This projector can be linked with video devices equipped with HDMI output terminal or DVI-D output terminal.
However, with some of them, this projector may not display any image or not operate correctly.
• If this projector doesn’t display any image or not operate correctly, see the operation manual of the video device
for its connection.
• Use of a long cable may decrease the quality of projected images.
Connection (for video equipment having an HDMI terminal)
• Use the attached DVI-HDMI conversion cable.
• Use AUDIO IN 1 terminal for audio input.
HDMI
Equipment having an
HDMI terminal
To HDMI terminal
COMPUTER/COMPONENT
VIDEO DVI-D (HDCP)
To audio input
terminals
To audio output
terminals
Audio cable (option)
DVI-HDMI conversion cable
Viewing video images (continued)
CB(PB)Y CR(P ) R
B G R
AUDIO IN 1
BNC cable (option)
DVD player or HDTV decoder
BNC-RCA connector (option)
COMPUTER/COMPONENT
VIDEO IN 1
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fi tting (Y, C , C ). When connecting such DVD player with this B R
projector, use the COMPUTER/COMPONENT VIDEO IN 1 terminals.
• The terminal’s names Y, P , and P are given as examples of when a HDTV decoder is connected.B R
• The terminal’s names vary depending on the connected devices.
• Use BNC cables for connection.
• Image may not be projected correctly with some DVD players.
• If colors aren’t displayed correctly when the projector is connected to a high-defi nition video device having R, G,
and B output terminals, set COMPUTER INPUT to RGB in the SIGNAL menu.
Audio cable (option)
To audio output terminals

EN-24
2. INSTALLATION menu
Menu operation (continued)
ITEM SETTING FUNCTION
LAMP MODE STANDARD Select this option when you want to view images in a well-lit room.
LOW Select to moderate the intensity of the lamp. The operating sound is
reduced and the lamp lifetime becomes longer.
• When the lamp mode is switched, the projected image may fl icker.
• Frequent switching of the lamp mode may damage the lamp.
AUTO POWER ON ON / OFF When ON is chosen, the lamp is automatically lit when the power cord is
plugged in the wall outlet. Choose ON when using the projector mounted
on the ceiling.
• The projector is in the stand-by mode when the lamp is off. Use the
remote control to turn on the lamp.
AUTO POWER OFF OFF / 5-60min Use to set the time elapsed before the projector enters the stand-by
mode when there is no signal input from the source.
IMAGE CAPTURE Use to capture the screen for the splash screen. (See page 32.)
SPLASH SCREEN ON / OFF Choose ON to display the splash screen when the power is turned on.
• The splash screen can be changed. (See page 32.)
BACK COLOR BLUE / BLACK / IMAGE Use to select the background from among BLUE, BLACK and IMAGE,
which will be displayed when there is no signal input from the source.
When IMAGE is selected, the splash screen will be displayed.
MUTE MODE BLACK / IMAGE Use to choose the background, either BLACK, or IMAGE, which will be
displayed when the AV MUTE button is pressed. When IMAGE is chosen,
the splash screen will be displayed.
IMAGE REVERSE OFF Select when viewing images from the front with the projector installed on
the fl oor.
MIRROR Select when viewing images projected from the behind of the screen with
the projector installed on the fl oor.
INVERT Select when viewing images projected from the behind of the screen with
the projector installed on the ceiling.
MIRROR INVERT Select when viewing images from the front with the projector installed on
the ceiling.
LENS LOCK ZOOM/FOCUS LOCK Use to enable or cancel the FOCUS LOCK and ZOOM LOCK.
LENS SHIFT LOCK Use to enable or cancel the LENS SHIFT LOCK.
LENS SHIFT RESET Use to reset the position of the lens to the factory setting.
• Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default
whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to
LOW about 1 minute after turn-on.
• You can’t set IMAGE CAPTURE and SPLASH SCREEN when PASSWORD FUNCTION in the FEATURE menu has been set to
SPLASH ID SCREEN to enable the password lock.
• When you continue projection for a long time with BACK COLOR or MUTE MODE set to IMAGE, an afterimage may persist on
the screen. (See page 43.)
INSTALLATION
opt.
LAMP MODE
OFF
AUTO POWER
ON
STANDARD
ON SPLASH
SCREEN ON
AUTO POWER
OFF OFF
BACK COLOR BLUE
OFF
IMAGE
REVERSE
BLACKMUTE MODE
IMAGE
CAPTURE SETUP
LENS LOCK OK
Product specificaties
Merk: | Mitsubishi |
Categorie: | Beamer |
Model: | fl6900u |
Kleur van het product: | Wit |
Gewicht: | 9800 g |
Geluidsniveau: | 35 dB |
Plaatsing: | Plafond |
Connectiviteitstechnologie: | Bedraad |
Ethernet LAN: | Ja |
Ondersteunde video-modi: | 1080i, 1080p, 480i, 480p, 720p |
Meegeleverde kabels: | Serie |
Typische contrastverhouding: | 1000:1 |
Projector helderheid: | 4000 ANSI lumens |
Projectietechnologie: | LCD |
Projector native resolution: | 1080p (1920x1080) |
Geschikt voor schermmaten: | 60 - 250 " |
Projectie-afstand objectief: | - m |
Frequentiebereik horizontaal: | 15 - 100 kHz |
Frequentiebereik verticaal: | 50 - 120 Hz |
Aantal USB 2.0-poorten: | 1 |
VGA (D-Sub)poort(en): | 1 |
Soort serieële aansluiting: | RS-232 |
Audio-ingang (L, R): | 2 |
PC audio ingang: | Ja |
S-Video ingang: | 1 |
DVI-poort: | Ja |
Aantal Ethernet LAN (RJ-45)-poorten: | 1 |
Brandpuntbereik: | 51 - 64 mm |
Levensduur van de lichtbron: | 2000 uur |
Type lichtbron: | Lamp |
Ingebouwde luidsprekers: | Ja |
Gemiddeld vermogen: | 10 W |
Aantal ingebouwde luidsprekers: | 1 |
Stroomverbruik (in standby): | - W |
Formaat analoog signaal: | NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM |
Volledige HD: | Ja |
Ingang stroom: | Ja |
RS-232 port: | 1 |
3D: | Nee |
Lampvermogen: | 275 W |
Audio-ingangen: | 1 |
Audio-uitgang: | 1 |
Resolutie (maximum digitaal): | 2073600 Pixels |
Ondersteunde grafische resoluties: | 1600 x 1200 (UXGA), 1920 x 1080 (HD 1080) |
Levensduur van de lichtbron (besparingsmodus): | 4000 uur |
Power LED: | Ja |
Dot clock scanfrequentie: | 162 MHz |
Geluidsniveau (spaarzame modus): | 29 dB |
Focusbereik lens: | 1.8 - 2.1 |
Afmetingen (B x D x H): | 441.96 x 434.34 x 205.74 mm |
Afstandsbediening inbegrepen: | Ja |
Lamp sterkte (spaarzame modus): | 220 W |
Wifi: | Nee |
AC-ingangsspanning: | 100 - 240 V |
AC-ingangsfrequentie: | 50 - 60 Hz |
Stroomverbruik (typisch): | 430 W |
Batterijen inbegrepen: | Ja |
Heb je hulp nodig?
Als je hulp nodig hebt met Mitsubishi fl6900u stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Beamer Mitsubishi

20 Juni 2023

18 Juni 2023

12 Juni 2023

6 Juni 2023

29 Mei 2023

11 Mei 2023

6 Mei 2023

5 Mei 2023

5 Mei 2023

4 Mei 2023
Handleiding Beamer
- Beamer Philips
- Beamer HP
- Beamer Sony
- Beamer Samsung
- Beamer Xiaomi
- Beamer Casio
- Beamer Panasonic
- Beamer Epson
- Beamer LG
- Beamer Asus
- Beamer Canon
- Beamer JVC
- Beamer Medion
- Beamer Toshiba
- Beamer Yamaha
- Beamer Acco
- Beamer Acer
- Beamer Aiptek
- Beamer Anker
- Beamer AOpen
- Beamer ASK Proxima
- Beamer Auna
- Beamer Barco
- Beamer Bauer
- Beamer BenQ
- Beamer Blaupunkt
- Beamer D-Link
- Beamer Dell
- Beamer Easymaxx
- Beamer Eiki
- Beamer Elmo
- Beamer Emtec
- Beamer GPX
- Beamer Hama
- Beamer Hisense
- Beamer Hitachi
- Beamer Ibm
- Beamer InFocus
- Beamer Ion
- Beamer Klarstein
- Beamer Kodak
- Beamer Kogan
- Beamer La Vague
- Beamer Leica
- Beamer Lenco
- Beamer Lenovo
- Beamer Livoo
- Beamer Marantz
- Beamer Maxell
- Beamer Nebula
- Beamer Nec
- Beamer PLUS
- Beamer Polaroid
- Beamer Pyle
- Beamer RCA
- Beamer Reflecta
- Beamer Renkforce
- Beamer Ricoh
- Beamer Salora
- Beamer Sanyo
- Beamer Sharp
- Beamer Showtec
- Beamer Smart
- Beamer Smartwares
- Beamer Speaka
- Beamer Steinel
- Beamer Strong
- Beamer Technaxx
- Beamer Viewsonic
- Beamer Vivitek
- Beamer Vogels
- Beamer XGIMI
- Beamer ZTE
- Beamer Odys
- Beamer OK
- Beamer Oki
- Beamer Optoma
- Beamer Overmax
- Beamer 3M
- Beamer Krüger And Matz
- Beamer Naxa
- Beamer Steren
- Beamer Eurolite
- Beamer Prixton
- Beamer Planar
- Beamer Dukane
- Beamer Yaber
- Beamer Mimio
- Beamer Da-Lite
- Beamer Adj
- Beamer Dahua Technology
- Beamer Derksen
- Beamer Celly
- Beamer Promethean
- Beamer Stairville
- Beamer Laserworld
- Beamer Beghelli
- Beamer Cameo
- Beamer Tzumi
- Beamer EKO
- Beamer MicroVision
- Beamer Elite Screens
- Beamer Celexon
- Beamer Fun Generation
- Beamer Christie
- Beamer Futurelight
- Beamer Varytec
- Beamer Ultimea
- Beamer Dracast
- Beamer Dream Vision
- Beamer Knoll
- Beamer DTS
- Beamer Touchjet
- Beamer Boxlight
- Beamer AAXA Technologies
- Beamer Miroir
- Beamer Vankyo
- Beamer AWOL Vision
- Beamer Smart Tech
- Beamer Atlantis Land
- Beamer KickAss
- Beamer Microtek
- Beamer VAVA
- Beamer Panamorph
- Beamer Mirabella Genio
Nieuwste handleidingen voor Beamer

4 Maart 2025

4 Maart 2025

25 Februari 2025

20 Februari 2025

20 Februari 2025

20 Februari 2025

10 Februari 2025

30 Januari 2025

30 Januari 2025

30 Januari 2025