Milwaukee M18 Fuel 2881-22 Handleiding
Milwaukee
Slijpmachine
M18 Fuel 2881-22
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 Fuel 2881-22 (28 pagina's) in de categorie Slijpmachine. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/28
Cat. No. / No de cat.
2880-20, 2881-20
M18 FUELâ„¢ 4-1/2" / 5" BRAKING GRINDER
MEULEUSE À FREIN DE 115 mm mm / 125 (4-1/2" / 5") M18 FUEL™
ESMERILADORA CON FRENO DE 115 mm mm / 125 (4-1/2" / 5")
M18 FUELâ„¢
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and speciîš¿ca-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, îš¿re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiîš¿ed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of an GFCI
reduces the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o󰀨-position before connecting to power
source and/or battery pack, picking up or carry-
ing the tool. Carrying power tools with your îš¿nger
on the switch or energizing power tools that have
the switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
• Do not use the power tool if the switch does not
turn it on and o󰀨. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
• Maintain power tools and accessories. Check for
misalignment or binding of moving parts, break-
age of parts and any other condition that may
a󰀨ect the power tool’s operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and the
work to be performed. Use of the power tool for
operations di󰀨erent from those intended could result
in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of îš¿re when used
with another battery pack.
• Use power tools only with specically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and îš¿re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
3
to another. Shorting the battery terminals together
may cause burns or a îš¿re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, ush with water. If liquid con-
tacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is dam-
aged or modiîš¿ed. Damaged or modiîš¿ed batteries
may exhibit unpredictable behavior resulting in îš¿re,
explosion or risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to îš¿re or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range speciîš¿ed in the instructions.
Charging improperly or at temperatures outside
the speciîš¿ed range may damage the battery and
increase the risk of îš¿re.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
GRINDERS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing or Cutting-O󰀨 Operations:
• This power tool is intended to function as a
grinder, sander, wire brush, hole cutter or cut-
o󰀨 tool. Read all safety warnings, instructions,
illustrations and speciîš¿cations provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, îš¿re and/or
serious injury.
• Operations such as polishing are not to be
performed with this power tool. Operations for
which the power tool was not designed may create
a hazard and cause personal injury.
• Do not convert this power tool to operate in a
way which is not specîš¿cally designed and speci-
îš¿ed by the tool manufacturer. Such a conversion
may result in a loss of control and cause serious
personal injury.
• Do not use accessories which are not spe-
cifically designed and specified by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
• The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and y apart.
• The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
• The dimensions of the accessory mounting must
îš¿t the dimensions of the mounting hardware of
the power tool. Accessories that do not match the
mounting hardware of the power tool will run out of
balance, vibrate excessively and may cause loss of
control.
• Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or acces-
sory is dropped, inspect for damage or install
an undamaged accessory. After inspecting and
installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum
no-load speed for one minute. Damaged acces-
sories will normally break apart during this test time.
• Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping ying debris generated by various applica-
tions. The dust mask or respirator must be capable
of îš¿ltrating particles generated by the particular
application. Prolonged exposure to high intensity
noise may cause hearing loss.
• Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Fragments
of workpiece or of a broken accessory may y away
and cause injury beyond immediate area of opera-
tion.
• Hold the power tool by insulated gripping sur-
faces only, when performing an operation where
the cutting tool may contact hidden wiring.
Contact with a "live" wire will also make exposed
metal parts of the power tool "live" and could give
the operator an electric shock.
• Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
• Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the ac-
cessory into your body.
• Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
• Do not operate the power tool near ammable
materials. Sparks could ignite these materials.
• Do not use accessories that require liquid cool-
ants. Using water or other liquid coolants may result
in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory’s rotation at
the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel that
is entering into the pinch point can dig into the surface
of the material causing the wheel to climb out or kick
out. The wheel may either jump toward or away from
the operator, depending on direction of the wheel’s
movement at the point of pinching. Abrasive wheels
may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Slijpmachine |
| Model: | M18 Fuel 2881-22 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee M18 Fuel 2881-22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Slijpmachine Milwaukee
10 April 2024
8 April 2024
3 April 2024
3 April 2024
18 Maart 2024
18 Maart 2024
21 Februari 2024
21 Februari 2024
21 Februari 2024
21 Februari 2024
Handleiding Slijpmachine
- Slijpmachine Bosch
- Slijpmachine AEG
- Slijpmachine DeWalt
- Slijpmachine ABB
- Slijpmachine Adler
- Slijpmachine Aquapur
- Slijpmachine ATI-ZDL
- Slijpmachine Batavia
- Slijpmachine Bavaria
- Slijpmachine Black Decker
- Slijpmachine Bort
- Slijpmachine Bruder Mannesmann
- Slijpmachine Bunn
- Slijpmachine Defort
- Slijpmachine Dolmar
- Slijpmachine Dolmar(Makita)
- Slijpmachine Dremel
- Slijpmachine Duro
- Slijpmachine Duro Pro
- Slijpmachine Einhell
- Slijpmachine Ergofix
- Slijpmachine Fein
- Slijpmachine Felisatti
- Slijpmachine Ferm
- Slijpmachine Festool
- Slijpmachine Flex
- Slijpmachine Florabest
- Slijpmachine Gamma
- Slijpmachine Global
- Slijpmachine Goon
- Slijpmachine Gorenje
- Slijpmachine Gude
- Slijpmachine Gude Pro
- Slijpmachine Hikoki
- Slijpmachine Hitachi
- Slijpmachine Holzmann
- Slijpmachine Husqvarna
- Slijpmachine Hyundai
- Slijpmachine Kawasaki
- Slijpmachine Kress
- Slijpmachine Maestro
- Slijpmachine Makita
- Slijpmachine Maktec
- Slijpmachine Max
- Slijpmachine Mesko
- Slijpmachine Metabo
- Slijpmachine Parkside
- Slijpmachine Pattfield
- Slijpmachine Powerfix
- Slijpmachine Powerplus
- Slijpmachine Profitec
- Slijpmachine Ryobi
- Slijpmachine Scheppach
- Slijpmachine Silvercrest
- Slijpmachine Silverline
- Slijpmachine Skil
- Slijpmachine Solo
- Slijpmachine Stanley
- Slijpmachine Stomer
- Slijpmachine Tanaka
- Slijpmachine Toolcraft
- Slijpmachine Toolland
- Slijpmachine Trotec
- Slijpmachine United Office
- Slijpmachine Vonroc
- Slijpmachine Westfalia
- Slijpmachine Workzone
- Slijpmachine Worx
- Slijpmachine Ozito
- Slijpmachine Black And Decker
- Slijpmachine ECG
- Slijpmachine Steren
- Slijpmachine Cocraft
- Slijpmachine Meec Tools
- Slijpmachine Yamato
- Slijpmachine Genesis
- Slijpmachine Eibenstock
- Slijpmachine Hilti
- Slijpmachine Nuova Simonelli
- Slijpmachine Cotech
- Slijpmachine Power Craft
- Slijpmachine Truper
- Slijpmachine Fieldmann
- Slijpmachine Mirka
- Slijpmachine Proxxon
- Slijpmachine Malmbergs
- Slijpmachine Porter-Cable
- Slijpmachine Graphite
- Slijpmachine RIDGID
- Slijpmachine Tryton
- Slijpmachine Sthor
- Slijpmachine Craftsman
- Slijpmachine Rikon
- Slijpmachine Chicago Pneumatic
- Slijpmachine Alpha Tools
- Slijpmachine Hazet
- Slijpmachine Yato
- Slijpmachine Baumr-AG
- Slijpmachine Meister Craft
- Slijpmachine Neo
- Slijpmachine Victoria Arduino
- Slijpmachine SW-Stahl
- Slijpmachine Cleco
- Slijpmachine Einhell Bavaria
- Slijpmachine McKenzie
- Slijpmachine Proviel
- Slijpmachine Gladiator
- Slijpmachine Rodcraft
- Slijpmachine Bavaria By Einhell
- Slijpmachine Classic Power
- Slijpmachine Handwerk
Nieuwste handleidingen voor Slijpmachine
10 December 2024
5 December 2024
4 December 2024
4 December 2024
23 November 2024
22 November 2024
19 November 2024
19 November 2024
19 November 2024
19 November 2024