Milwaukee M18 Fuel 2653-22 Handleiding

Milwaukee Schroefmachine M18 Fuel 2653-22

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 Fuel 2653-22 (11 pagina's) in de categorie Schroefmachine. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/11

Cat. No.

No de cat.

2653-20

2654-20

2655-20

2655B-20

M18™ FUEL™ 1/4" HEX IMPACT DRIVER, 1/2" IMPACT WRENCHES &

3/8" IMPACT WRENCH

TOURNEVIS À PERCUSSION HEXAGONAL 6 mm (1/4"), CLÉS À CHOCS

DE 1/2" & CLÉS À CHOCS DE 3/8" DE M18™ FUEL™

DESTORNILLADOR HEXAGONAL DE IMPACTO DE 6 mm (1/4"), LLAVES

DE IMPACTO DE 1/2" & LLAVES DE IMPACTO DE 3/8" DE M18™ FUEL™

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive at-

mospheres, such as in the presence of ﬂ am-

mable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or

serious injury. Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and o. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc., in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations dierent from those intended could

result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inﬂ

uence of drugs, alcohol or medication.

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

• Recharge only with the charger speciﬁ ed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of ﬁ re

when used with another battery pack.

• Use power tools only with speciﬁ cally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁ re.

BATTERY TOOL USE AND CARE

SPECIFIC SAFETY RULES

• When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small metal

objects that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a ﬁ re.

• Under abusive conditions, liquid may be eject-

ed from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

• Hold power tool by insulated gripping surfaces,

when performing an operation where the fas-

tener may contact hidden wiring. Fasteners

contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the

operator an electric shock.

• Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

• Use only sockets and other accessories spe-

ciﬁ cally designed for use on impact wrenches

and drivers. Other sockets and accessories might

shatter or break causing injury.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

Cat. No.

Volts

RPM IPM

Mode Speed Mode Impacts

2653-20

2654-20

2655-20

2655B-20

0-850

0-2100

0-2900

0-900

0-1600

0-2400

0-1700

0-2000

0-2400

0-1700

0-2000

0-2400

1750

2850

3600

1100

2400

3100

2500

3000

3100

2500

3000

3100

FUNCTIONAL DESCRIPTION

SPECIFICATIONS

1. Hex drive chuck

(2653-20)

2. LED

3. Control switch

4. Trigger

5. 3-Mode drive control

6. Belt clip

7. 3/8" Square drive anvil (2654-20)

8. 1/2" Square drive anvil with pin detent (2655-20)

9. 1/2" Square drive anvil with ball detent (2655B-20)

Attaching and Removing Accessories

1/2" Impact Wrench with Pin Detent

(Cat. No. 2655-20)

1. Use only the appropriate size Square Drive

Sockets.

2. To attach a socket, align the hole in the acces-

sory with the detent pin on the anvil. Hold the

detent pin in while pushing the socket onto the

anvil. The detent pin will snap into place in the

hole to secure the socket.

3. To remove the socket, insert a nail or other thin

object into the hole in the accessory and press

in the detent pin. Pull the accessory off the anvil.

ASSEMBLY

WARNING Recharge only with the

charger speciﬁ ed for the battery. For speciﬁ c

charging instructions, read the operator’s

manual supplied with your charger and battery.

Inserting/Removing the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

To insert the battery, slide the pack into the body of

the tool. Make sure it latches securely into place.

WARNING Use only sockets and other

accessories speciﬁ cally designed for use on

impact wrenches and drivers. Other sockets

and accessories might shatter or break caus-

ing injury.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

1/2" Impact Wrench with Ball Detent

(Cat. No. 2655B-20)

1. Use only the appropriate size Square Drive

Sockets.

2. To attach a socket, align the hole in the acces-

sory with the detent ball on the anvil. Push the

socket onto the anvil. The detent ball will snap

into place in the hole to secure the socket.

3. To remove the accessory, pull the accessory

o the anvil.

3/8" Impact Wrench (Cat. No. 2654-20)

1. Use only the appropriate size Square Drive

Sockets.

2. To attach a socket, align the accessory with the

anvil and push it ﬁ rmly over the retaining ring.

3. To remove the accessory, pull the accessory

o the anvil.

1/4" Hex Impact Driver (Cat. No. 2653-20)

This impact driver is intended for use with drill and

driver bits.

1. To attach an accessory, press the shank into the

hex drive chuck.

2. To remove the accessory, pull out the ring and

remove the accessory. Release the ring.

Starting, Stopping and Controlling Speed

These tools may be operated at any speed from

0 to full speed.

1. To start the tool, pull the trigger.

NOTE: An LED is turned on when the trigger is

pulled.

2. To vary the driving speed, simply increase or

decrease pressure on the trigger. The further

the trigger is pulled, the greater the speed.

3. To stop the tool, release the trigger and the

electric brake stops the tool instantly.

Impacting Techniques

The longer a bolt, screw, or nut is impacted, the

tighter it will become. To help prevent damaging the

fasteners or workpieces, avoid excessive impact-

ing. Be particularly careful when impacting smaller

fasteners because they require less impacting to

reach optimum torque.

Practice with various fasteners, noting the length

of time required to reach the desired torque. Check

the tightness with a hand-torque wrench. If the

fasteners are too tight, reduce the impacting time.

If they are not tight enough, increase the impact-

ing time.

Oil, dirt, rust or other matter on the threads or

under the head of the fastener aects the degree

of tightness.

The torque required to loosen a fastener averages

75% to 80% of the tightening torque, depending on

the condition of the contacting surfaces.

On light gasket jobs, run each fastener down to a

relatively light torque and use a hand torque wrench

for ﬁ nal tightening.

Using the Drive Control

The drive control button is used to adjust the torque,

rotation speed (RPM), and impact speed (IPM) for

the application (see Speciﬁ

cations

chart for RPM

and IPM).

To select the drive control mode:

1. Pull and release the trigger to turn on the tool.

The current mode indicator is lit.

2. Press the drive control button to cycle through

the 3 modes. When the desired mode indiator

is lit, begin work.

Push for

Forward

Push for

Reverse

PUSH TO CENTER TO LOCK

OPERATION

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

1 2 3

Mode

Indicator

Drive

Control

Button

Using the Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the ON/OFF switch is not pressed. Always allow

the motor to come to a complete stop before using

the control switch.

1. For forward (clockwise) rotation, push the

control switch in the direction shown. Check the

direction of rotation before use.

2. For reverse (counterclockwise) rotation, push

the control switch in the direction shown. Check

the direction of rotation before use.

3. To lock the trigger, push the control switch to the

center position. The trigger will not work when

the control switch is in the locked position.

Always remove the battery pack before perform-

ing maintenance, changing accessories, storing

the tool and any time the tool is not in use.

SYMBOLOGY

Volts

Direct Current

Impacts per Minute Under

Load (IPM)

No Load Revolutions per

Minute (RPM)

Underwriters Laboratories, Inc.

United States and Canada

Product specificaties

Merk:	Milwaukee
Categorie:	Schroefmachine
Model:	M18 Fuel 2653-22

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee M18 Fuel 2653-22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Schroefmachine Milwaukee

Milwaukee M12 FCIWP12G3 Handleiding

20 November 2024

Milwaukee M12 BDD Handleiding

16 November 2024

Milwaukee M18 BDD Handleiding

16 November 2024

Milwaukee M18 ONEFMTIW2FC12 Handleiding

4 September 2024

Milwaukee M18 FUEL 2953-20 Handleiding

23 Juni 2024

Milwaukee M18 FUEL FSGC Handleiding

10 Juni 2024

Milwaukee M18 ONEFHIWF12 Handleiding

5 Mei 2024

Milwaukee M18 FUEL FMTIW2F38 Handleiding

10 April 2024

Milwaukee M12 FID2 Handleiding

10 April 2024

Milwaukee M12 FUEL FRAIWF12 Handleiding

10 April 2024

Handleiding Schroefmachine

Nieuwste handleidingen voor Schroefmachine

Proviel HTBS 710 Handleiding

19 November 2024

Prowork PSD 4,8 Handleiding

19 November 2024

Bavaria By Einhell BAS 4,8 L Handleiding

19 November 2024

Alpha Tools AS 12 A Handleiding

17 November 2024

Netter Vibration PKL 740 Handleiding

17 November 2024

Hazet 9022 P-2 Handleiding

15 November 2024

Hazet 9021-3 Handleiding

15 November 2024

Hazet 9012MT Handleiding

15 November 2024

Hazet 6001-3.0/3 Handleiding

12 November 2024

Hazet 6001-1.5/3 Handleiding

12 November 2024