Milwaukee M12 Fuel 2553-21 Handleiding
Milwaukee
Schroefmachine
M12 Fuel 2553-21
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M12 Fuel 2553-21 (16 pagina's) in de categorie Schroefmachine. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/16
Cat. No. / No de cat.
2552-20, 2553-20
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
M12 FUEL™ 1/4" IMPACT WRENCH & 1/4" HEX IMPACT DRIVER
CLÉS À CHOCS 1/4" & TOURNEVIS À PERCUSSION
HEXAGONAL 6 mm (1/4") DE M12 FUEL™
LLAVES DE IMPACTO DE 1/4" & DESTORNILLADOR
HEXAGONAL DE IMPACTO DE 6 mm (1/4") DE M12 FUEL™
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
• Do not use the power tool if the switch does not
turn it on and o. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may aect the power tool’s operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations dierent from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
3
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is dam-
aged or modied. Damaged or modied batteries
may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging
improperly or at temperatures outside the specied
range may damage the battery and increase the risk
of re.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
IMPACT WRENCH/DRIVER
• Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting
a “live” wire may make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
• Wear ear protectors when impact drilling. Expo-
sure to noise can cause hearing loss.
• Use only sockets and other accessories spe-
cically designed for use on impact wrenches
and drivers. Other sockets and accessories might
shatter or break causing injury.
•
WARNING
To reduce the risk of injury, when
working in dusty situations, wear
appropriate respiratory protection or use an
OSHA compliant dust extraction solution.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
Impacts per Minute Under Load (IPM)
C US
UL Listing for Canada and U.S.
SPECIFICATIONS
Volts 12 DC..............................................................
Battery Type .................................................M12™
Charger Type M12™ ................................................
Recommended Ambient
Operating Temperature .................... 0°F to 125°F
Cat. No. 2552-20 .....................................................
RPM ........................................................... 0 - 3200
IPM ............................................................ 0 - 4300
Cat. No. 2553-20 .....................................................
RPM ........................................................... 0 - 3300
IPM ............................................................ 0 - 4000
FUNCTIONAL DESCRIPTION
5
1. Belt clip
2. Control switch
3. Handle
4. Trigger
5. LED
6. Hex square drive shank (2552-20)
7. 4-Mode drive control
8. Hex drive chuck (2553-20)
1
2
4
3
7
6
8
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Schroefmachine |
| Model: | M12 Fuel 2553-21 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee M12 Fuel 2553-21 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schroefmachine Milwaukee
20 November 2024
16 November 2024
16 November 2024
4 September 2024
23 Juni 2024
10 Juni 2024
5 Mei 2024
10 April 2024
10 April 2024
10 April 2024
Handleiding Schroefmachine
- Schroefmachine Bosch
- Schroefmachine Panasonic
- Schroefmachine AEG
- Schroefmachine DeWalt
- Schroefmachine Basetech
- Schroefmachine Batavia
- Schroefmachine Bavaria
- Schroefmachine Bruder Mannesmann
- Schroefmachine Dremel
- Schroefmachine Easymaxx
- Schroefmachine Einhell
- Schroefmachine Elu
- Schroefmachine Fein
- Schroefmachine Ferm
- Schroefmachine Festool
- Schroefmachine Goon
- Schroefmachine Greenworks
- Schroefmachine Gude
- Schroefmachine Hikoki
- Schroefmachine Hitachi
- Schroefmachine Ingersoll Rand
- Schroefmachine Kawasaki
- Schroefmachine Kress
- Schroefmachine Laserliner
- Schroefmachine Makita
- Schroefmachine Maktec
- Schroefmachine Matrix
- Schroefmachine Metabo
- Schroefmachine Parkside
- Schroefmachine Powerfix
- Schroefmachine Powerplus
- Schroefmachine Ryobi
- Schroefmachine Silverline
- Schroefmachine Skil
- Schroefmachine Stanley
- Schroefmachine Toolcraft
- Schroefmachine Toolland
- Schroefmachine Trotec
- Schroefmachine Velleman
- Schroefmachine Vonroc
- Schroefmachine Westfalia
- Schroefmachine Wiha
- Schroefmachine Worx
- Schroefmachine Omega
- Schroefmachine Ozito
- Schroefmachine Black And Decker
- Schroefmachine Steren
- Schroefmachine Urrea
- Schroefmachine Cocraft
- Schroefmachine Meec Tools
- Schroefmachine Senco
- Schroefmachine Genesis
- Schroefmachine Hilti
- Schroefmachine Facom
- Schroefmachine Kraftwerk
- Schroefmachine EMOS
- Schroefmachine Cotech
- Schroefmachine Power Craft
- Schroefmachine Tacklife
- Schroefmachine Truper
- Schroefmachine Fieldmann
- Schroefmachine Mafell
- Schroefmachine Carrera
- Schroefmachine Biltema
- Schroefmachine Porter-Cable
- Schroefmachine Beta
- Schroefmachine Dedra
- Schroefmachine MSW
- Schroefmachine Sthor
- Schroefmachine Craftsman
- Schroefmachine Chamberlain
- Schroefmachine Chicago Pneumatic
- Schroefmachine Alpha Tools
- Schroefmachine Hazet
- Schroefmachine Yato
- Schroefmachine Abac
- Schroefmachine Meister Craft
- Schroefmachine StarTech.com
- Schroefmachine Park Tool
- Schroefmachine Pansam
- Schroefmachine Gedore
- Schroefmachine Netter Vibration
- Schroefmachine SW-Stahl
- Schroefmachine Cleco
- Schroefmachine Einhell Bavaria
- Schroefmachine Prowork
- Schroefmachine Proviel
- Schroefmachine Weidmüller
- Schroefmachine Wera
- Schroefmachine Rodcraft
- Schroefmachine Bavaria By Einhell
- Schroefmachine TAURUS Titanium
Nieuwste handleidingen voor Schroefmachine
23 November 2024
23 November 2024
23 November 2024
23 November 2024
19 November 2024
19 November 2024
19 November 2024
17 November 2024
17 November 2024
15 November 2024