Meliconi fully 8 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Meliconi fully 8 (4 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Fully 8 RC
Keep this booklet for future reference.
Thank you for choosing a Meliconi remote control.
The FULLY 8 RC universal remote control is ideal for replacing up to 8 remote controls of any brand for TV, Digital Terrestrial
(TER), Satellite (SAT) Decoders, DVD players (including Blu Ray), Videotape recorders (VCR), Personal video recorders
(PVR), cable TV (CAB), other audio video equipment (AUX) or decoders for ADSL TV (ADSL). The remote control has a non-
volatile memory, meaning that it does not lose its settings even if there are no batteries in it.
IMPORTANT: the device must not be exposed to excessive heat sources.
USE OF THE BUTTONS AND FUNCTIONS
The functions of the buttons described below are available only if they are also present on the original remote control.
Volume control +/–
TELETEXT buttons
ON/OFF switches the device OFF and
in some cases ON
Numeric keypad
Con rm selection
MUTE
turns sound OFF and ON
For selecting an external input
source
For selecting the next programme P+
or the previous programme P–
For moving around within the MENU
Fastext functions or for selecting
sub-menus using colours
Buttons for selecting the device to be
controlled.
DVD/PVR RECORD PAUSE STOP PLAY
buttons
DVD and PVR forward/back functions
Speci c buttons for decoder
Displays the list of programmes
Selects analogue/digital
Selects digital TV and radio
INSERTING THE BATTERIES
The remote control requires 2 new 1.5V alkaline AAA/LR03 batteries.
Insert them as illustrated.
Try pressing a number button and check that the red light remains lit
continuously until you release the button: if the light ashes, the batteri-
es inserted are not charged and are about to go at, therefore you must
substitute them.
Do not leave at batteries inserted, as liquid may leak and damage the remote control
The Fully 8 RC remote control is a universal remote, so its memory contains data relating to numerous devices of various
brands available on the market.
Each original device has a speci c code which must be used to set up the remote control.
Therefore, to use your Fully 8 RC you must enter the speci c code for each device you wish to control.
So use one of the following methods to identify the correct code and set it in your remote control:
A) - INTERNET (recommended)
B) - CELL PHONE (SMS)
C) - MANUAL SEARCH
SETTING CODES
If you have an Internet connection available, follow the on-line guide on the www.meliconi.com/guida website to identify
the speci c codes for the devices you wish to command. Then set the codes manually in your MELICONI remote control
as described in the ENTERING THE CODE DIRECTLY procedure.
SETTING CODES USING INTERNET
Today, Meliconi gives customers who don’t have internet the chance to receive the codes for programming their remote
control directly on their cell phone.
Simply send an SMS to this number 0039 345 7518893 as follows: 8A, Type, Brand, Model
- Type = indicate the device to be controlled using one of the following abbreviations: TV - SAT - DVD - VCR - TER
(Digital Terrestrial decoder) - AUX (other audio video device).
- Brand, Model = to indicate the brand and the model of the device to be controlled.
Example: 8A, TV, PHILIPS, 32PFL3614 (if you don’t know the model, don’t write anything after the brand).
Once you have received the SMS with the list of codes, set the rst code in the remote control as described in the
ENTERING THE CODE DIRECTLY section.
Stand in front of the device with the MELICONI remote control. Turn the device on and then press the OFF button on the
remote (or the PLAY button if the device is a VCR/DVD).
If the device does NOT switch off (or if the VCR/DVD does not start playing), try setting the consecutive code in the SMS
list in the remote control.
When the device reacts check whether the other buttons are operating correctly too.
If they do, the remote control is ready to use.
If they don’t, you are probably using an incorrect code destined for a very similar device; at this point ignore the
SMS list and consult the SETTING CODES USING A MANUAL CODE section to nd a more suitable code.
SETTING CODES USING A CELL PHONE
NOTE: If you don’t receive an SMS on your cell phone or if the message says ERROR / NO CODE, it means the
system has not been able to process the data you have sent; Do not try sending another SMS use the MANUAL
SEARCH instead.
(only to be performed if you know the speci c code to be set)
ENTERING THE CODE DIRECTLY
Three long ashes indicate a correct setting. If they do not appear, repeat the procedure.
1. Hold down the selection button corresponding to the device whose code you want to enter (e.g.: ) until the indicator
light starts to ash.
2. When the indicator light starts ashing, release the button and immediately enter the speci c code previously found (e.g.:
1306).
1. Switch on the device to be programmed: if TV, SAT, TER select a programme - if DVD insert a DVD, for videotape recorders
insert a cassette
2. Hold down the selection button corresponding to the device whose code you want to nd (e.g.: ) until the indicator
light starts to ash.
3. Now release the button and brie y press the button or for a DVD, VCR and PVR.
4. The indicator light ashes faster; the remote control is ready for the search.
5. Point the remote control at the device. Slowly press and release the or button several times, stopping when the
device responds correctly to the command sent (you may need to press the button several dozen times).
6. When the device responds correctly, press the button. Three long ashes indicate that the operation was completed
correctly.
Check that the other buttons correspond to the functions of the original remote control; if not, it is likely that the code found
is incorrect, but is used for a very similar device. In that case, repeat the procedure from point 2.
NOTE: During the search the indicator stops ashing and the remote control exits the programming mode in the fol-
lowing cases:
• if for 12 seconds the button indicated is not pressed or if another button is pressed
• if the list of codes to nd is terminated. If this happens, go to the www.meliconi.com website
DISPLAY CODE IN USE
If you set up the remote control using the MANUAL SEARCH procedure, obtain and make a note of the code in use as follows:
1. Hold down the selection button corresponding to the device whose code you want to nd (e.g.: ) until the indicator
light starts to ash.
2. When the indicator light starts ashing, release the button and brie y press the button.
3. After a pause of several seconds, the indicator light produces four sets of ashes, spaced out, corresponding to the code to
be obtained. Count the number of ashes. Each set of ashes corresponds to one gure in the code. Ten ashes correspond
to the gure 0.
(only to be performed if the speci c code could not be found)
SETTING CODES USING A MANUAL SEARCH


Product specificaties

Merk: Meliconi
Categorie: Afstandsbediening
Model: fully 8
Kleur van het product: Zwart
Ingebouwd display: Nee
Aan/uitschakelaar: Ja
Interface: IR Draadloos
Input type: Drukknopen
Batterijtechnologie: Alkaline
Number of devices supported: 8
Cursortoets: Ja

Heb je hulp nodig?

Als je hulp nodig hebt met Meliconi fully 8 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afstandsbediening Meliconi

Handleiding Afstandsbediening

Nieuwste handleidingen voor Afstandsbediening