Makita LS002G Handleiding

Makita Niet gecategoriseerd LS002G

Lees hieronder de 📖 handleiding in het Nederlandse voor Makita LS002G (40 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 205 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/40
INSTRUCTION MANUAL
Cordless Slide Compound Miter Saw
LS002G
ENGLISH: Original instructions
Read before use.
2 ENGLISH
SPECIFICATIONS
Model: LS002G
Blade diameter 216 mm
Hole (arbor) diameter (country speciîš¿c) 15.88 mm / 25.4 mm / 30 mm
Max. kerf thickness of the saw blade 2.4 mm
Max. miter angle Left 60°, Right 60°
Max. bevel angle Left 48°, Right 48°
No load speed 4,800 min-1
Dimensions (L x W x H) 702 mm x 551 mm x 557 mm
Rated voltage D.C. 36 V - 40 V max
Net weight 16.4 - 17.0 kg
• Due to our continuing program of research and development, the specications herein are subject to change
without notice.
• Specications may di󰀨er from country to country.
• The weight may di󰀨er depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge BL4025 / BL4040
Charger DC40RA
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or îš¿re.
Cutting capacities (H x W) with blade 216 mm in diameter
Miter angle Bevel angle
45° (left) 45° (right)0°
0° 50 mm x 312 mm 70 mm x 312 mm 30 mm x 312 mm
45° (left and right) 50 mm x 220 mm 70 mm x 220 mm 30 mm x 220 mm
60° (left and right) 70 mm x 155 mm– –
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
To avoid injury from ying debris, keep
holding the saw head down, after making
cuts, until the blade has come to a com-
plete stop.
When performing slide cut, îš¿rst pull car-
riage fully and press down handle, then
push carriage toward the guide fence.
When performing bevel cut, îš¿rst loosen the
grip dial and tilt the carriage to the desired
angle, then tighten the grip dial.
When tilting the blade beyond the range 0°
- 45°, turn the releasing lever for 48° bevel
angle in clockwise direction.
Do not place hand or îš¿ngers close to the
blade.
Wear safety glasses.
Do not stare at operating lamp.
Ni-MH
Li-ion
Only for EU countries
Do not dispose of electric equipment or
battery pack together with household waste
material!
In observance of the European Directives,
on Waste Electric and Electronic
Equipment and Batteries and Accumulators
and Waste Batteries and Accumulators
and their implementation in accordance
with national laws, electric equipment and
batteries and battery pack(s) that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.
Intended use
The tool is intended for accurate straight and miter cutting in wood.
With appropriate saw blades, aluminum can also be sawed.
Do not use the saw to cut other than wood, aluminum or
similar materials.
3 ENGLISH
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-3-9:
Sound pressure level (LpA ) : 89 dB(A)
Sound power level (LWA) : 100 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE:
The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during actual
use of the power tool can di󰀨er from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING: Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
o󰀨 and when it is running idle in addition to the
trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and speciîš¿cations provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, îš¿re and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiîš¿ed plugs and matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
7.
Power tools can produce electromagnetic îš¿elds
(EMF) that are not harmful to the user. However,
users of pacemakers and other similar medical
devices should contact the maker of their device and/
or doctor for advice before operating this power tool.
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
power tools may result in serious personal injury.
2. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
3. Prevent unintentional starting. Ensure the
switch is in the o󰀨-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your îš¿nger on the switch or energising power tools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.

Product specificaties

Merk: Makita
Categorie: Niet gecategoriseerd
Model: LS002G

Heb je hulp nodig?

Als je hulp nodig hebt met Makita LS002G stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Makita

Makita

Makita UN001G Handleiding

5 September 2024
Makita

Makita TM001G Handleiding

5 September 2024
Makita

Makita DJS101 Handleiding

28 Mei 2024
Makita

Makita ADP05 Handleiding

7 Mei 2024
Makita

Makita DC4001 Handleiding

7 Mei 2024
Makita

Makita BCV03 Handleiding

7 Mei 2024
Makita

Makita DC18WA Handleiding

7 Mei 2024
Makita

Makita DML803 Handleiding

7 Mei 2024
Makita

Makita DCJ205 Handleiding

7 Mei 2024
Makita

Makita RM350D Handleiding

8 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Electrolux

Electrolux STA9 Handleiding

23 November 2024
Electrolux

Electrolux UMP3 Handleiding

23 November 2024
Electrolux

Electrolux ZS70GL Handleiding

23 November 2024
Bosch

Bosch HEZ8TK36UC Handleiding

23 November 2024
Bosch

Bosch HEZ8ZZ36UC Handleiding

23 November 2024
Bosch

Bosch HDZIT301 Handleiding

23 November 2024
Bosch

Bosch HEZBS301 Handleiding

23 November 2024
LG

LG LX-330 Handleiding

23 November 2024
Stamos

Stamos S-PLASMA 60U Handleiding

23 November 2024
Bosch

Bosch KSZ2AVU00 Handleiding

22 November 2024