Makita GD0600 Handleiding

Makita Slijpmachine GD0600

Lees hieronder de 📖 handleiding in het Nederlandse voor Makita GD0600 (44 pagina's) in de categorie Slijpmachine. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/44

GB Die Grinder Instruction manual

F Meuleuse droite Manuel d’instructions

D Geradschleifer Betriebsanleitung

I Smerigliatrice diritta Istruzioni per l’uso

NL Stempelslijpmachine Gebruiksaanwijzing

E Amoladora recta Manual de instrucciones

P Rectificadora recta Manual de instruções

DK Ligesliber Brugsanvisning

GR Ευθυλειαντήρας Οδηγίες χρήσης

GD0600

007052

1 2007053 007055

3 4015678 007056

5007054

123

10 mm (3/8”) MAX.

ENGLISH (Original instructions)

Explanation of general view

SPECIFICATIONS

• Due to our continuing program of research and development, the specifications herein are subject to change without

notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Intended use ENE050-1

The tool is intended for grinding ferrous materials or

deburring castings.

Power supply ENF002-2

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

General Power Tool Safety

Warnings GEA010-1

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

DIE GRINDER SAFETY

WARNINGS GEB034-9

Safety Warnings Common for Grinding Operation:

1. This power tool is intended to function as a

grinder. Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious

injury.

2. Operations such as sanding, wire brushing,

polishing or cutting-off are not recommended to

be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

3. Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

4. The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated

speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories

cannot be adequately controlled.

6. The arbour size of accessories must properly fit

the collet of the power tool. Accessories that do not

match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause

loss of control.

7. Mandrel mounted accessories must be fully

inserted into the collet or chuck. If the mandrel is

insufficiently held and/or the overhang of the wheel is

too long, the mounted accessory may become loose

and be ejected at high velocity.

8. Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks. If power tool or accessory is

dropped, inspect for damage or install an

undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum no-

load speed for one minute. Damaged accessories

will normally break apart during this test time.

9. Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping flying debris generated by various

operations. The dust mask or respirator must be

capable of filtrating particles generated by your

1. Switch lever

2. Lock-off lever

3. Lock button

4. Wrench 13

5. Collet nut

6. Side handle

Model GD0600

Max. collet capacity 6 mm or 6.35 mm (1/4”)

Wheel Point Max. wheel diameter 38 mm

Max. mandrel (shank) length 46 mm

Rated speed (n) / No load speed (n 0) 25,000 min-1

Overall length 358 mm

Net weight 1.7 kg

Safety class /II

Product specificaties

Merk:	Makita
Categorie:	Slijpmachine
Model:	GD0600
Kleur van het product:	Blauw
Gewicht:	1600 g
Breedte:	82 mm
Diepte:	358 mm
Hoogte:	82 mm
Geluidsniveau:	73 dB
Stroombron:	AC
Input vermogen:	400 W
Stationair toerental (max):	25000 RPM
Trillingsniveau (slijpen):	2.5 m/s²
Maximum diameter van de slijpschijf:	6 mm