Magnavox MM438 Handleiding

Magnavox Speaker MM438

Lees hieronder de 📖 handleiding in het Nederlandse voor Magnavox MM438 (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT

REMOVE THE COVER (OR BACK). NO USER

SERVICEABLE PART INSIDE, REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DANGEROUS VOLTAGE: The lighting flash with arrowhead

symbol ,within an equilateral

triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’

enclosure, that maybe of sufficient magnitude to constitute

ATTENTION: The exclamation point within an equilateral

triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions

in the literature accompanying the appliance.

1 Read these instructions .

All the safety and operating instructions should be read

before the appliance is operated.

2 Keep these instructions .

The safety and operating instructions should be kept for

future reference.

3 Heed all warnings.

All warnings on the appliance and in the operating

instructions should be adhered to.

4. Follow all instructions

All operation and use instructions should be followed.

5. Do not use this apparatus near water

The appliance should not be used near water; for example,

near a bath tub, washbowl, kitchen sink, laundry tub, in

awet basement, or near a swimming pool.

6. Clean only with dry cloth

The appliance should be cleaned only as recommended by

the manufacturer.

7 Do not block any ventilation openings. Install in .

accordance with the manufacturer’ instructions.

Slots and openings in the cabinet and in the back or bottom

are provided for ventilation, to ensure reliable operation of

the product and to protect it from overheating. These

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or similar surface. This product should never be

placed near or over a radiator or heat source. This product

should not be placed in a built-in installation, such as a

bookcase or rack unless proper ventilation is provided or

the manufacturer’ instructions have been adhered to.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a

third grounding prong. The wide or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10. Product the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments / accessories specified by the

manufacturer.

12. Use only with a cart, stand, tripod, bracket,

or table specified by the manufacturer,

or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

An appliance and cart combination should be moved

with care. Quick stop, excessive force and uneven

surfaces may cause the appliance and cart

combination to overturn.

13. Unplug this apparatus during lightning

storms or when unused for long periods of time.

To protect your product from a lightning storm, or

when it is left unattended and unused for long periods

of time, unplug it from the wall outlet and disconnect

the antenna or cable system. This will prevent damage

to the product due to lightning and power-line surges.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord

or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

15. Power source

This product should be operated only from the type of

power source indicated on the marking label. If you

are not sure of the type of power supply to your

home, consult your appliance dealer or local power

company. For products intended to operate from

battery power, or other source, refer to the operation

instructions.

16. Power lines

An outside antenna system should not be located in

the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep

from touching such power lines or circuits as contact

with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as

this can result in a risk of fire or electric shock.

18. Object and liquid entry

Never push objects of any kind into the product

through openings as they may touch dangerous

voltage points or short out parts that could result in

fire or electric shock. Never spill or spray any type of

liquid on the product.

19. Outdoor antenna grounding

If an outside antenna is connected

to the product, be sure the antenna

system is grounded so as to provide

some protection against voltage surges

and built up static charges. Section 810

of the National Electric Code ANSI/ NFPA 70 provides

information with respect to proper grounding of the

mast and supporting structure, grounding of the lead-

in wire to an antenna discharge product, size of

grounding conductors, location of antenna-

discharge product, connection to grounding

electrodes and requirements for the grounding

electrodes.

20. Service

Do not attempt to service this product yourself as

opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

21. Replacement parts

When replacement parts are required, be sure the

service technician uses replacement parts specified

by the manufacturer or those that have the same

characteristics as the original parts. Unauthorized

substitutions may result in fire or electric shock or

other hazards.

22. Safety check

Upon completion of any service or repairs to this

product, ask the service technician to perform safety

checks to determine that the product is in proper

operating condition.

23 Wall or ceiling mounting.

The product should be mounted to a wall or ceiling

only as recommended by the manufacturer.

24. Damage requiring service

A. Unplug this product from the wall outlet and refer

service to qualified service personnel under the

following conditions.

B. When the power- supply cord or plug is damaged.

C. If liquid has been spilled or objects have fallen into

the product.

D. If the product has been exposed to rain or water.

E. If the product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions, as an adjustment of other controls

may result in damage and will require extensive

work by a qualified technician to restore the

product to its normal operation.

If the product has been dropped or the cabinet has F.

been damaged.

G. When the product exhibits a distinct change in

performance- this indicates a need for service.

25. Note to CATV system installer

This reminder is provided to call the CATV system

installer' attention to Article 820- 40 of the NEC

that provides guidelines for proper grounding and,

in particular, specifies that the cable ground shall be

connected to the grounding system of the building,

as close to the point of cable entry as practical.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

FCC NOTICE:

or relocate the receiving antenna. Reorient

Increase the separation between the equipment

and receiver.

Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

Consult the dealer or an experienced radio/TV

technician for help.

FCC STATEMENT:

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and

(2) This device must accept any interference

received, including interference that may cause

undesired operation. The antenna(s) used for this

transmitter must be installed to provide a

separation distance of at least 20 cm from all

persons and must not be co-located or operating

in conjunction with any other antenna or

transmitter.

FCC WARNING:

To assure continued operation, follow the attached

installation instructions and use only shield cables

when connecting to other devices. Changes or

modifications not expressly approved by the party

responsible for compliance could void the user's

authority to operate the equipment.

NOTE: Refer all servicing to qualified service personnel.

Servicing is required when the unit has been damaged

in any way such as the following: the power-supply

cord or plug has been damaged, liquid has been spilled

into unit, the unit has been exposed to rain or

moisture, the unit has been dropped or the unit does

not operate normally.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

Before using the unit, be sure to read all operating

instruction carefully, please note that these are general

precautions and may not pertain to your unit. For example,

this unit may not have the capability to be connected to an

outdoor antenna.

POWER SOURCE:

TROUBLESHOOTING GUIDE:

To Wall Outlet

The unit has a built in Li-ion rechargeable battery, recharge it before use or when it is drained as follows:

1. Connect the small plug from the supplied AC/DC Adaptor to the DC IN Jack on the rear of unit.

2. Plug the AC/DC Adaptor to the AC wall outlet having AC 100-240V~, 50/60Hz as illustrated below.

3. During charging, the Red Charging Indicator on the rear of unit will illuminate. When finished, it will turn off.

4. During charging, you can also play and listening music at the same time.

Notes:

Your battery will last longer if you're following these simple guidelines for charging and storing.

A. Before first time use, charge it approximately 5 hours until the unit is fully charged.

B. Recharge and store the unit within the temperature range of 5°C~35°C (40°F~95°F).

C. Do not charge longer than 24 hours. Excessive charging or running the unit until battery fully

drains will damage battery. Battery life will be extended if you keep the battery fully charged.

D. Battery life naturally shortens slowly over time.

E. The rechargeable battery incorporated in this product is not user replaceable.

Check the following before requesting service:

SYMPTOM POSSIBLE EC EAUS

Can’ power on Built in battery drained

Volume of the unit was set to

minimum position

No Sound or sound weak

Sound distortion

BT not functioning

POSSIBLE ESOULTION

Volume level of paired/connected

device is in low level

Volume level too high

Volume level of the connected/

paired device too high

The external BT Device had NOT

paired to the unit

The external BT device too far

from the unit

Rise the volume level of the

paired/connected device

Recharge the built-in battery as page 4

Increase the volume level by turning

the MASTER VOL (Volume) Control

Knob clockwise

3 4

AUX IN Mode:

To listen to music from an external Audio Player such as a MP3 Player, Discman …etc.

1. Connect one end of the supplied Audio Connection Cable to the AUX

Out/Line Out/Phone Jack on the external Audio Player.

2. Connect the other end of the cable to the AUX IN (Line In) Jack on the rear of unit as the illustrated below:

AUX Out:

To listen music from external Audio Amplifier:

1. Power on the unit and play music in any modes as instructed earlier.

2. Connect one end of the supplied Audio Connection Cable to the AUX/LINE (in) Jack on the external Audio Amplifier.

3. Connect the other end of the cable to the AUX OUT Jack on the rear of unit as the illustrated below:

Microphone:

To sing or play the Electric Guitar with the playing music:

1. Power on the unit and play music in any modes as instructed earlier.

2. Connect the plug from Microphone/Electric Guitar (Not included) to the MIC (Microphone) Jacks on the rear of unit.

3. Turn the MIC VOL (Microphone Volume) Control Knob to adjust the sound level of Microphone/Electric Guitar.

4. Turn the MIC ECHO (Microphone Echo) Control Knob to adjust the echo effect of Microphone/Electric Guitar.

Note: If feedback noise (high audio frequency noise) is sounding from the speakers, turn the MIC VOL

(Microphone Volume) Knob counterclockwise to reduce the microphone volume level or keep the

Microphone away from the speakers.

Note: When the Audio Connection Cable was inserted into the AUX OUT Jack. The sound from speakers will be cut off.

Unplug the cable from the jack after use.

3. Power on the unit and enter to AUX IN (Line In) mode as previously instructed.

Indicator“LinE”will appear on the display.

4. Play the music on the connected Player as usual. (Make sure the volume level of

the connected Audio Player is turned to high level.)

5. During playback,press the >ll Button to mute the sound, press again to turn the sound back.

1 x AC/DC Adapter(Input: AC 100-240 V~, 50/60 Hz, 300mA ; Output: DC 9V, 1300mA， )

SPECIFICATIONS:

PACKAGE INCLUDES:

Power source: Built-in DC 7.4V, 1800 mAh (Total 13.32 WH) rechargeable Li-ion

BT Version: 2.1

BT Operation Distance: ≥32 Feet in open area

1 x User’s Manual

Battery;

Recharge by DC 9 V, 1300mA, through DC IN Jack

SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE

Radio Frequency: 87.5-108MHz

LOCATION OF CONTROLS:

1. Power ON/OFF Switch

2.LED Display

3.FM Telescope Antenna

4.BASS VOL (Volume) Control Knob

MASTER VOL (Volume) Control Knob

Charging Indicator

DC IN Jack

AUX IN Jack

AUX OUT Jack

USB Port

TF (Micro SD Card) Slot

MIC ECHO (Microphone Echo) Control Knob

MIC VOL (Microphone Volume) Control Knob

23. Speakers with Decorative LED Lights

5.“1” – “6” Buttons (Decorative

LED Lights Blinking Mode Selection/FM

Memory Buttons)

7. l Button

8. Rep (Repeat) Button

9. ll Button

Light (Decorative LED Lights) On/Off Button

l Button10.

11.Mode Button

12.

13.

14.

15.

16.

17.

18.

19.

20.

21. MIC (Microphone) Jacks

22. Five (5) Bands Equalizer

USB Device Playback Mode:

To play the music in USB Device:

1. In power off mode, insert the USB Device (Not included) into the USB Port on the rear of unit as the illustrated below:

USB

TF (Micro SD Card) Playback Mode:

Notes:

To play the music in TF (Micro SD Card) :

1. In power off mode, insert the Micro SD Card (Not included) into the TF (Micro SD Card) Slot on

the rear of unit with contact finger face to up as the illustrated below:

2. Power on the unit by press the Power ON/OFF Switch to ON position. The unit will automatically

play the song/music in the TF (Micro SD Card).

3. During playback:

Press the ll Button to mute the sound, press again to turn the sound back.

Press the l or l Button repeatedly to skip tracks.

Press the Rep (Repeat) Button repeatedly to activate and set (or turn off) the repeat playback mode.

Press the Mode Button repeatedly to switch to other playback mode.

Up to 16 GB Micro SD Card the unit supports to play.

Before replacing Micro SD Card, make sure the unit has been powered off.

When inserting the Micro SD Card, make sure the direction you selected is correct. Never insert

violently to avoid damaging the Micro SD Card or the unit.

If it doesn’ work, please check if the direction is correct.

You also need to download the desired music in MP3 format into the Micro SD Card before insert into the unit.

Notes:

FM Radio:

Up to 16 GB USB Device the unit supports to play.

Before replacing USB Device, make sure the unit has been powered off.

When inserting the USB Device, make sure the direction you selected is correct.

Never insert violently to avoid damaging the USB Device or the unit.

You also need to download the desired music in MP3 format into the USB Device before insert into the unit.

1. Power on the unit and enter to Radio mode as previously instructed. Radio frequency will appear on the display.

2. Press the l or l Buttons to automatically search and play the previous/next

available FM station. Repeat the same procedures until the desired FM station was been searched and play.

3. Preset and play:

A. Receiving the desired FM station as previously instructed, press and holding either“1”–“6”Buttons until

“F XX”appear on the display to store the desired FM station into the memory.

B. Repeat the same procedures until all desired FM stations (Maximum 6 stations) were stored into the desired button.

C. Press either“1”–“6”Buttons to play the stored FM station.

Antennas:

The telescope FM antenna is for FM radio reception, which provides adequate reception in most areas.

If reception is weak, extend to its full length or adjust the angle to improve reception.

2. Power on the unit by press the Power ON/OFF Switch to ON position. The unit

will automatically play the song/music in the USB Device.

3. During playback:

Press the ll Button to mute the sound, press again to turn the sound back.

Press the l or l Button repeatedly to skip tracks.

Press the Rep (Repeat) Button repeatedly to activate and set (or turn off) the repeat playback mode.

Press the Mode Button repeatedly to switch to other playback mode.

AUX IN

Audio connection

Cable (included)

Audio connection

Cable (included)

ipad, discman

AUX OUT

OPERATIONS:

General Operation:

1. Recharged the built in Li-ion battery as previously instructed.

2. Press the Power ON/OFF Switch to ON position to power on the unit. The Decorative LED Lights will illuminate.

3. Press the Mode Button repeatedly to switch to desired playback mode. The correspondent indicator will appear

(or illuminate) on the display with your selection (see list below):

Playback Mode: Indicators:

4. During playback,

A. Turn the MASTER VOL (Volume) Control Knob on the top of unit to adjust volume level as desired.

B. Turn the BASS VOL (Volume) Control Knob on the top of unit to adjust the bass level as desired.

C. Slide the control knobs of the Five (5) Band Equalizer up or down to adjust the audio frequency as desired.

D. Press the Light (Decorative LED Lights) On/Off Button repeatedly to turn On/Off the Decorative LED Lights.

At the light on mode:

Press the“1”Button repeatedly to set or reset the color of the Decorative LED Lights to Red, Green or Blue.

Press the“2”–“6”Buttons to set or reset the blinking mode of the Decorative LED Lights.

5. When finished listening, press the POWER ON/OFF Button to OFF position to shut off the unit.

BT Mode:

BT (Bluetooth) pairing:

First time use or re-pairing the unit to a new BT Device, pair as follows:

1. Power on the unit and enter to BT mode as previously instructed.“bLUE BT”will appear on the display

and“BT”in it will blink. The unit also will sound a prompt“Enter to Bluetooth”.

2. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen

instructions from the external BT Device. After paired, the unit will sound a prompt“Bluetooth connected”

and the BT Indicator will stop blinking.

3. If pairing is complete you may now play music and answer calls with your external BT Device.

4. During playback:

Press the ll Button on the unit to pause, press again to resume normal playback.

Press the l or l Buttons repeatedly to skip tracks.

●

Normal operation after pairing:

Notes:

When the external BT Device searched the unit, our model number“MM438”

will appear on the display of external BT Device.

If while pairing you are asked for a code please try "0000" or "1234".

1. Power on the unit and enter to BT mode as previously instructed.“bLUE BT”will

appear on the display and“BT”in it will blink. The unit also will sound a prompt “Enter to Bluetooth”.

2. Wait a few seconds until the unit is automatically paired to the external BT Device. The unit will sound a

prompt“Bluetooth connected”and the BT Indicator will stop blinking.

3. After pairing is complete you may now play music and answer calls with your external BT Device.

Place the external BT device

close to the unit

Pair the external BT Device to

the unit as page 5

Reduce the volume level of the

connected/paired device

Reduce the volume level by turning the

MASTER VOL (Volume) Control Knob

counterclockwise

▲

SD Card

9 10

13 14 15 16 17 18 19 20 21

23 23

AUX IN (Line in) “LINE”will appear on the display

Radio FM Band Radio frequency“XX.X”or

“XXX.X”will appear on the display

TF (If Micro SD Card inserted) Indicator“USB TF”on display will illuminate

USB (If USB Device inserted) Indicator“USB TF”on display will illuminate

BT (Bluetooth) “bLUE BT”will appear on the display

1 x Audio Connection Cable with 3.5mm Plugs

Product specificaties

Merk:	Magnavox
Categorie:	Speaker
Model:	MM438

Heb je hulp nodig?

Als je hulp nodig hebt met Magnavox MM438 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Speaker Magnavox

Magnavox MD6924 Handleiding

7 Januari 2025

Magnavox MD6920 Handleiding

7 Januari 2025

Magnavox MSH315V Handleiding

7 Januari 2025

Magnavox MSH317 Handleiding

7 Januari 2025

Magnavox MMA3626 Handleiding

7 Januari 2025

Magnavox MD6972 Handleiding

7 Januari 2025

Magnavox MD6923 Handleiding

7 Januari 2025

Magnavox MMA3628 Handleiding

7 Januari 2025

Magnavox MHT833 Handleiding

7 Januari 2025

Magnavox MHT913R Handleiding

7 Januari 2025

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Electro-Voice Sx600 Handleiding

8 Januari 2025

Electro-Voice XLE191-FG Handleiding

8 Januari 2025

Sonance MAG6R Handleiding

8 Januari 2025

Sonance MAG5.1R Handleiding

8 Januari 2025

Duronic BX48 Handleiding

8 Januari 2025

Sonance Visual Performance VP38R Handleiding

8 Januari 2025

Sonance Visual Performance Extreme VPXT8R Handleiding

8 Januari 2025

Definitive Technology Dymension LS-80 Handleiding

7 Januari 2025

Definitive Technology Dymension Outdoor LS- Handleiding

7 Januari 2025

Definitive Technology Dymension LS-400 Handleiding

7 Januari 2025