Lorex LNB8111B Handleiding

Lorex Bewakingscamera LNB8111B

Lees hieronder de 📖 handleiding in het Nederlandse voor Lorex LNB8111B (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
4K Ultra HD IR Bullet IP Camera
LNB8111_QSG_EN_R3
Quick Start Guide
English Version 3.0
Copyright © 2018 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves
the right to modify product design, specifications and prices, without
notice and without incurring any obligation. E&OE. All rights reserved.
• For a full list of compatible recorders, visit lorex.com/compatibility.
• Not intended for submersion in water. Installation in a sheltered
location recommended.
• This camera includes an Auto Mechanical IR Cut Filter. When the
camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and
indicates that the camera filter is working.
Disclaimers
Dimensions
7.1” / 180mm2.8”/70mm
LNB8111 SERIES
Resources
Need Help?
Visit us online for up-to-date software
and complete instruction manuals
Click on the Downloads tab
4
Visit lorex.com
Search for the model number
of your product
Click on your product in the
search results
3
2
1
• 4K Ultra HD IR Bullet IP Camera
• Mounting Kit*
• Mounting Template*
• Ethernet Extension Cable*
* Per camera in multi-camera packs.
Package Contents
ATTENTION:
It is recommended to connect the camera to the NVR or an external PoE
switch. If using a DC power adapter (not included) with the camera, a
REGULATED power supply is REQUIRED for use with this camera. Use of
a non-regulated, non-conforming power supply can damage this product
and voids the warranty.
• Use the camera only with compatible Lorex NVRs.
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the camera within given temperature, humidity and voltage levels
noted in the camera’s specifications.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source of
intense light.
• Use only a regulated power supply with the product (optional). Use of a
non-regulated, non-conforming power supply can damage the product
and void the warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do not use
any harsh, chemical-based cleaners.
• The supplied cable is rated for surface mounting only. Cables for in-wall
and floor-to-floor installations are sold separately (CMR type). These
and other cables are available at lorex.com
Safety Precautions
• Point the camera where there is the least amount of obstructions
(i.e., tree branches).
• Install the camera where vandals cannot easily reach.
• Secure cabling so that it is not exposed or easily cut.
• This camera is rated for outdoor use. Installation in a sheltered
location is recommended.
Installation Tips
www.lorex.com
Camera Overview
B
A
C
D
E
A. Light Sensor and IR LEDs
B. Sun Shield Screw
C. Adjustment Screw
D. Camera Base
E. Reset Button: Press
and hold the button
for 5 seconds to reset
the camera to default
settings.
Connecting the CamerasSetup Diagram
CameraNVR
Scenario 1: Connect Cameras to NVR
Scenario 2: Connect Cameras to Local Area Network (LAN)
Router
CameraRouter
PoE Switch
ATTENTION:
• This camera is compatible only with select NVRs supporting 4K
camera input. For a list of compatible recorders, visit
lorex.com/compatibility.
• You must connect the camera to a supporting H.265 NVR to take
advantage of H.265 compression. For instructions on enabling
H.265 compression, visit lorex.com, and search for “How do I
enable H.265 compression?”.
NVR
LNB8111_QSG_EN_R3
Installing the Camera
ATTENTION:
Test your camera prior to selecting a permanent mounting location by
temporarily connecting the camera and cable to your NVR.
Before Installing the Camera
• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.
• If you run the cables along the
wall / ceiling, you must run the
cable through the on cable notch
the base. This will keep the camera
base flush to the surface when mounted. Cable Notch
To install your camera:
1. Use the included mounting template to mark holes for the
screws. Drill holes for the mounting screws.
NOTE: Insert the included drywall anchors if you are
installing the camera in drywall.
2. Connect cables as shown in the section “Connecting the
Camera”.
4. Use a Philips screwdriver
(not included) to loosen the adjustment screw.
5. Adjust the camera
position as
needed:
6. Tighten the adjustment
screw to secure the
position.
• You can use a RJ45 coupler or switch (not included) to connect male
ends of Ethernet cable together.
• To extend the cable run beyond 300ft (92m), a switch will be required
(sold separately).
Extend the Ethernet cable run for your camera up to 300ft (92m).
See table below. It is recommended to use UL CMR approved cables
available at lorex.com.
Cable Extension Options
Cable Type Max Cable Run
Distance
Max # of
Extensions
CAT5e (or higher) Ethernet cable 300ft (92m) 3
Problem Solution
No picture / signal • Ensure the camera is connected to a compatible
NVR supporting 4K camera input. For full camera
compatibility, visit lorex.com/compatibility.
• The camera may take up to 1 minute to power up
after being connected to the NVR. Wait two minutes
before following the steps below.
• Ensure the camera is connected to your NVR or to
your local network.
• If you are not using PoE, you must connect the
camera to a 12V DC power adapter (not included).
• If the camera is connected to the LAN, you must
search your network for cameras using the NVR. See
the NVR’s instruction manual.
• Ensure your NVR is properly connected to a TV/
monitor.
• There may be an issue with your extension cable run.
Connect the camera to the NVR using a different
Ethernet cable.
Picture is too
bright
• Ensure your camera isn’t pointed directly at a
source of light (e.g., sun or spot light).
• Slide the sunshade forward to block excess light.
• Move your camera to a different location.
• Check the brightness and contrast settings on the
NVR.
Picture is too dark • If using during the day, the camera may not be
getting enough light. Slide the sunshade backwards
to let in more light.
• Check the brightness and contrast settings on the
NVR.
Night vision is not
working
• The night vision activates when light levels drop. The
area may have too much light.
Picture is not clear • Check the camera lens for dirt, dust, spiderwebs.
Clean the lens with a soft, clean cloth.
• Make sure that the cable run is within the limitations
specified in the section ‘Cable Extension Options’.
• Remove the vinyl film from the camera lens when
your installation is complete.
Bright spot
in video when
viewing camera at
night
• Night vision reflects when pointing a camera through
a window. Move the camera to a different location.
Picture is in color
in dark conditions
• This camera comes with an image sensor that is
extra sensitive to light, meaning that the camera
stays in color mode at low-light conditions. For
instructions on how to make your camera switch to
night mode, visit lorex.com, and search for “How do I
make my camera switch to night mode?”.
Troubleshooting
Connect the Ethernet cable to
the camera.
Connect the other end of the
Ethernet cable to the NVR’s PoE
ports. The camera may take a
minute to power up after
being connected.
Connecting the Camera
Connect the other end of the
Ethernet cable to a router or
switch on your network. See
your NVR manual for details on
connecting the camera to your
NVR using a switch or router.
Camera NVR
OR
(Optional)
12V DC Power
Ethernet Cable
NOTE: A 12V DC power
adapter (model#: CVA4902,
not included) is only required
if connecting the camera’s
Ethernet cable to a router or
switch that does not support
PoE.
Mounting screws (4×)
Camera base
Drywall anchors (4×)
Mounting surface
3. Feed the cable through
the mounting surface
or cable notch and
mount the camera
stand to the surface
using the provided
screws.
Adjustment
screw
Using the Weather Resistant Cap (Optional)
Camera Ethernet Connector
O-Ring
Barrel End Cap
1. Fit the O-ring around the camera Ethernet connector.
2. Connect the cable to the camera Ethernet connector.
3. Twist the barrel securely onto the camera Ethernet connector. The
o-ring becomes compressed when the seal is properly tight.
4. Twist the end cap securely onto the barrel.
7. Remove the vinyl film from the camera lens when your
installation is complete.

Product specificaties

Merk: Lorex
Categorie: Bewakingscamera
Model: LNB8111B

Heb je hulp nodig?

Als je hulp nodig hebt met Lorex LNB8111B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Bewakingscamera Lorex

Lorex

Lorex W463AQ Handleiding

12 November 2024
Lorex

Lorex E842CA Handleiding

3 Juli 2024
Lorex

Lorex E842CAWP Handleiding

3 Juli 2024
Lorex

Lorex E842CAB Handleiding

3 Juli 2024
Lorex

Lorex LNE45DDW Handleiding

27 Mei 2024
Lorex

Lorex LNB45ABB Handleiding

27 Mei 2024
Lorex

Lorex W261AQ Handleiding

27 Mei 2024
Lorex

Lorex LNE45DDB Handleiding

27 Mei 2024
Lorex

Lorex LNB45ABW Handleiding

27 Mei 2024
Lorex

Lorex LNB8963B Handleiding

28 December 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Provision ISR

Provision ISR I3-350IP5SMVF Handleiding

20 November 2024
Provision ISR

Provision ISR I2-350A-28 Handleiding

20 November 2024
Provision ISR

Provision ISR I4-350A-MVF Handleiding

20 November 2024
Canon

Canon PowerShot GOLF Handleiding

20 November 2024
Flir

Flir FH-Series Handleiding

20 November 2024
EtiamPro

EtiamPro CCTVPROM23 Handleiding

17 November 2024
EtiamPro

EtiamPro CCTVPROM20W Handleiding

17 November 2024
Leviton

Leviton 68A02-2 Handleiding

17 November 2024
Reolink

Reolink RLK8-800D4 Handleiding

16 November 2024
Reolink

Reolink RLK16-800D8 Handleiding

16 November 2024