Lincoln Electric LT-7 Handleiding
Lees hieronder de đź“– handleiding in het Nederlandse voor Lincoln Electric LT-7 (56 pagina's) in de categorie Lasapparaat. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/56
Operator’s Manual
LT-7 Lightweight Tractor
Register your machine:
www.lincolnelectric.com/register
Authorized Service and Distributor Locator:
www.lincolnelectric.com/locator
IM279-C | Issue D ate Sept-13
© Lincoln Global, Inc. All Rights Reserved.
For use with machines having Code Numbers:
K227, K395 and K395-1
Save for future reference
Date Purchased
Code: (ex: 10859)
Serial: (ex: U1060512345)
THANK YOU FOR SELECTING
A QUALITY PRODUCT BY
LINCOLN ELEC TRIC.
Please examine Carton and equiPment For
damage immediately
When this equipment is shipped, title passes to the purchaser upon
receipt by the carrier. Consequently, Claims for material damaged in
shipment must be made by the purchaser against the transportation
company at the time the shipment is received.
saFety dePends on you
Lincoln arc welding and cutting equipment is designed and built with
safety in mind. However, your overall safety can be increased by
proper installation ... and thoughtful operation on your part.
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS
CONTAINED THROUGHOUT. And, most importantly, think before you
act and be careful.
This statement appears where the information must be followed
exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed to
avoid minor personal injury or damage to this equipment.
KeeP your head out oF the Fumes.
DON’T get too close to the arc. Use
corrective lenses if necessary to
stay a reasonable distance away
from the arc.
READ and obey the Material Safety
Data Sheet (MSDS) and the warning
label that appears on all containers
of welding materials.
USE ENOUGH VENTILATION or
exhaust at the arc, or both, to keep
the fumes and gases from your breathing zone and the general area.
IN A LARGE ROOM OR OUTDOORS, natural ventilation may be
adequate if you keep your head out of the fumes (See below).
USE NATURAL DRAFTS or fans to keep the fumes away from your
face.
If you de velop unusual symptoms, see your supervisor. Perhaps the
welding atmosphere and ventilation system should be checked.
wear CorreCt eye, ear & body ProteCtion
PROTECT your eyes and face with welding helmet
properly fitted and with proper grade of filter plate
(See ANSI Z49.1).
PROTECT your body from welding spatter and arc
flash with protective clothing including woolen
clothing, flame-proof apron and gloves, leather
leggings, and high boots.
PROTECT others from splatter, flash, and glare with
protective screens or barriers.
IN SOME AREAS, protection from noise may be
appropriate.
BE SURE protective equipment is in good condition.
Also, wear safety glasses in work area
AT A
AT A
AT A
AT AAT ALL
LL
LL
LLLL
T
T
T
TTI
I
I
IIM
M
M
MME
E
E
EES.
S.
S.
S.S.
S
S
S
SSP
P
P
PPEC
EC
EC
ECECI
I
I
IIA
A
A
AAL
L
L
L L SI
SI
SI
SISIT
T
T
TTUAT
UAT
UAT
UATUATI
I
I
IION
ON
ON
ONONS
S
S
SS
DO NOT WELD OR CUT containers or materials which previously had
been in contact with hazardous substances unless they are properly
cleaned. This is extremely dangerous.
DO NOT WELD OR CUT painted or plated parts unless special
precautions with ventilation have been taken. They can release highly
toxic fumes or gases.
A
A
A
AAd
d
d
ddd
d
d
ddit
it
it
ititi
i
i
iio
o
o
oon
n
n
nna
a
a
aal
l
l
ll p
p
p
p pr
r
r
rrec
ec
ec
ececa
a
a
aau
u
u
uut
t
t
tti
i
i
iio
o
o
oon
n
n
nnar
ar
ar
arary
y
y
yy m
m
m
m mea
ea
ea
eaeas
s
s
ssu
u
u
uure
re
re
reres
s
s
ss
PROTECT compressed gas cylinders from excessive heat, mechanical
shocks, and arcs; fasten cylinders so they cannot fall.
BE SURE cylinders are never grounded or part of an electrical circuit.
REMOVE all potential fire hazards from welding area.
ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR
IMMEDIATE USE AND KNOW HOW TO USE IT.
WARNING
CAUTION
SECTION A:
WARNINGS
CALIFORNIA PROPOSITION 65 WARNINGS
Di
Di
Di
DiDies
es
es
esesel
el
el
elel En
En
En
En Engi
gi
gi
gigin
n
n
nnes
es
es
eses
Diesel engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects, and other
reproductive harm.
G
G
G
GGa
a
a
aas
s
s
sso
o
o
ool
l
l
lli
i
i
iin
n
n
nne
e
e
ee E
E
E
E En
n
n
nng
g
g
ggi
i
i
iin
n
n
nne
e
e
ees
s
s
ss
The engine exhaust from this product contains chemicals known
to the State of California to cause cancer, birth defects, or other
reproductive harm.
arC welding Can be hazardous. ProteCt
yourselF and others From Possible serious
inJury or death. KeeP Children away. PaCe-
maKer wearers should Consult with their
doCtor beFore oPerating.
Read and understand the following safety highlights. For additional
safety information, it is strongly recommended that you purchase a
copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the
American Welding Society, P.O. Box 351040, Miami, Florida 33135 or
CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety”
booklet E205 is available from the Lincoln Electric Company, 22801
St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION,
MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
FOR ENGINE POWERED
EQUIPMENT.
1.a. Turn the engine off before troubleshooting
and maintenance work unless the
maintenance work requires it to be running.
1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes outdoors.
1.c. Do not add the fuel near an open flame
welding arc or when the engine is running.
Stop the engine and allow it to cool before
refueling to prevent spilled fuel from
vaporizing on contact with hot engine parts
and igniting. Do not spill fuel when filling
tank. If fuel is spilled, wipe it up and do not start engine until
fumes have been eliminated.
1.d. Keep all equipment safety guards, covers and
devices in position and in good repair.Keep
hands, hair, clothing and tools away from
V-belts, gears, fans and all other moving parts
when starting, operating or repairing
equipment.
1.e. In some cases it may be necessary to remove safety guards to
perform required maintenance. Remove guards only when
necessary and replace them when the maintenance requiring
their removal is complete. Always use the greatest care when
working near moving parts.
1.f. Do not put your hands near the engine fan. Do not attempt to
override the governor or idler by pushing on the throttle control
rods while the engine is running.
1.g. To prevent accidentally starting gasoline engines while turning
the engine or welding generator during maintenance work,
disconnect the spark plug wires, distributor cap or magneto wire
as appropriate.
1.h. To avoid scalding, do not remove the radiator
pressure cap when the engine is hot.
ELECTRIC AND
MAGNETIC FIELDS MAY
BE DANGEROUS
2.a. Electric current flowing through any conductor
causes localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and welding
machines
2.b. EMF fields may interfere with some pacemakers, and welders
having a pacemaker should consult their physician before
welding.
2.c. Exposure to EMF fields in welding may have other health effects
which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1. Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and work
cables. If the electrode cable is on your right side, the
work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as pos-
sible to the area being welded.
2.d.5. Do not work next to welding power source.
3
SAFETY
Product specificaties
| Merk: | Lincoln Electric |
| Categorie: | Lasapparaat |
| Model: | LT-7 |
Heb je hulp nodig?
Als je hulp nodig hebt met Lincoln Electric LT-7 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Lasapparaat Lincoln Electric
17 November 2024
13 November 2024
13 November 2024
13 November 2024
13 November 2024
13 November 2024
13 November 2024
5 November 2024
5 November 2024
5 November 2024
Handleiding Lasapparaat
- Lasapparaat Bavaria
- Lasapparaat Duro
- Lasapparaat Einhell
- Lasapparaat Ferm
- Lasapparaat Gude
- Lasapparaat Gys
- Lasapparaat Holzmann
- Lasapparaat Hyundai
- Lasapparaat Kemppi
- Lasapparaat Kibani
- Lasapparaat Parkside
- Lasapparaat Powerplus
- Lasapparaat Scheppach
- Lasapparaat Silverline
- Lasapparaat Stanley
- Lasapparaat Taurus
- Lasapparaat Telwin
- Lasapparaat Topcraft
- Lasapparaat Weller
- Lasapparaat Workzone
- Lasapparaat Ozito
- Lasapparaat Miller
- Lasapparaat Hilti
- Lasapparaat Herkules
- Lasapparaat MSW
- Lasapparaat SainSmart
- Lasapparaat Anova
- Lasapparaat Hyper Welding
- Lasapparaat Mag-Torch
- Lasapparaat UNIMIG
- Lasapparaat Amico Power
- Lasapparaat THUN
- Lasapparaat Esab
- Lasapparaat Topex
- Lasapparaat Stamos
Nieuwste handleidingen voor Lasapparaat
16 November 2024
15 November 2024
14 November 2024
5 November 2024
2 November 2024
2 November 2024
2 November 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024