Lightware WP-UMX-TP-TX100-EU Handleiding

Lightware AV extender WP-UMX-TP-TX100-EU

Lees hieronder de 📖 handleiding in het Nederlandse voor Lightware WP-UMX-TP-TX100-EU (1 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Quick Start Guide

FP-UMX-TP-TX100-GB3, TX100-LEGRAND

WP-UMX-TP-TX100-EU, TX100-EUROMOD,

WP-UMX-TP-TX100-UK, TX100-US

Further information

The document is valid with the following rmware version: 1.1.3

The Product brief and further information of this appliance is available at www.lightware.eu.

See the Downloads section on the website of the product.

sales@lightware.eu

+36 1 255 3800

support@lightware.eu

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 2.0

19200023

Important safety instructions

Please read and keep the information in the attached safety instructions supplied with the

product before start using the device.

Introduction

WP-UMX-TP-TX100 and FP-UMX-TP-TX100 are all-round, universal video and audio

extenders designed to handle digital video, analog video, and audio signals e.g. VGA,

YPbPr, RGB, DVI and HDMI 1.3 with analog stereo or even 7.1 HDMI embedded audio.

Analog signals are converted to digital formats and digital or digitized analog audio is

embedded in the video stream. Video, audio and remote power are carried over two twisted

pair cables. The transmitter handles HDCP encryption and has an HDCP enable/disable

function.

However the external dimensions and the housing is different of each transmitter, the

internal structure, the controls, connections and the functions are the same.

Box contents

Installation

1. Connect the VIDEO Out and the DDC OUT to a TP-RX unit. (e.g.: HDMI-TP-RX100R).

The device is automatically powered remotely by a properly congured RX device via

the DDC line connection, make sure to power on the RX device.

2. Select an EDID if it is necessary as it is described in the Remote management section.

3. Connect the monitor or other sink devices to the output of the receiver device.

4. Connect the desired sources to the transmitter's input connectors.

5. Now the unit is ready to operate, do not forget to set up the RX device as well.

Select video source

There are four operation modes available: DVI-I Digital input, DVI-I Analog input, VGA input

and automatic selection. The VIDEO SELECT button switches between these 4 modes in

a loop.

Front panel LEDS

DVI-I DIGITAL/ANALOG or VGA VIDEO LED

BLINKING: waiting for signal on the selected input

DVI-I DIGITAL and VGA VIDEO LED

BLINKING (alternately): waiting for signal in auto-select mode

VIDEO LED

ON: signal present

ON (and another one is blinking): signal present and auto-select mode active

The automatic selection mode checks DVI-I DIGITAL and VGA VIDEO signals continuously.

Remote management

Several functions of the transmitter are available only remotely via an

RS-232 pass through compatible RX device (e.g.: HDMI-TP-RX100R),

which is connected to a computer or controller device by a female-female

straight-through cable. The transmitter can be listed by the Lightware Device

Controller software by clicking on the Query button of the corresponding

serial port.

Input and Output settings

The settings are available on the I/O Parameters tab by clicking on the ‘inputs’ or ‘Ouput’.

There are several settings available. These setting are stored in non-volatile memory.

HDCP capability can be disabled in the WP-UMX-TP-TX100R. If the content is not

copyrighted the source can be forced to output non-encrypted signal. To ensure non-

encrypted signal from the source, go to input settings and remove the mark next to the

‘HDCP enable’ label.

Transmitter unit Mounting screws * Safety and warranty info,

Quick Start Guide

* Only for WP-UMX-TP-TX100-EU (2 pcs.), TX100-UK (2 pcs.) and TX100-US (4 pcs.)

models.

Front and rear views

Video out

DDC out

Button Lock

The buttons can be locked by pressing the VIDEO and AUDIO SELECT buttons at the same

time. Mode switching is indicated by slow blinking of all LEDs, invalid input is by fast blinking.

Select audio source

Press the AUDIO SELECT button, to switch between ANALOG / EMBEDDED AUDIO.

In auto-select mode the audio channels are selected by default based on video detection:

DVI-I DIGITAL signal detection connects the HDMI embedded audio, VGA VIDEO detection

connects the analog stereo input.

Resetting the device

There is a tiny RESET button available between AUDIO and VIDEO SELECT buttons. After

reset or normal startup the device checks all LEDs for ~1 second and then displays the

currently installed rmware version by blinking the DVI-I DIGITAL, DVI-I ANALOG and VGA

VIDEO LEDs.

Factory resetting the device

Factory reset restores the input and output settings; the emulated and user EDIDs and the

enabled state of HDCP capability.

Press the RESET button once, whilst holding the VIDEO SELECT button till the device

reboots itself (4-5 seconds) and starts to display the rmware version for the second time.

Port diagram

Standalone application

Safety and

warranty

info

Quick

Start

Guide

A/D

converter

De-embedder

Embedder

Processor

A/D

converter

Analog audio in 2/1 audio

switch

Digital video in

Analog video in 2/1 video

switch

DDC out

Video out

VGA in

DVI-I in

Left in

Right in

+12V REMOTE POWER SEND

+12V REMOTE POWER RECEIVE

+12V DC POWER

+12V REMOTE POWER SEND

+12V REMOTE POWER RECEIVE

+12V DC POWER

Product specificaties

Merk:	Lightware
Categorie:	AV extender
Model:	WP-UMX-TP-TX100-EU
Kleur van het product:	Zwart
Gewicht:	290 g
Breedte:	150 mm
Diepte:	41.9 mm
Hoogte:	80 mm
Soort:	AV-zender
LED-indicatoren:	Ja
Bluetooth:	Nee
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Ondersteunde video-modi:	1080p
Maximum resolutie:	1920 x 1200 Pixels
Vermogensverbruik (max):	4 W
Certificering:	CE
HDCP:	Ja
3D:	Ja
Audio-ingangen:	2
Materiaal:	Metaal
Ondersteunde grafische resoluties:	1920 x 1200 (WUXGA)
VGA (D-Sub) invoer ports:	1
Audio-uitgangskanalen:	7.1 kanalen
DVI input ports:	1
RJ-45 uitgang ports:	2
Bandbreedte:	6.75 Gbit/s
Operating voltage:	12 V
Maximaal bereik:	20 m
Wifi:	Nee
Stroomverbruik (typisch):	3.2 W
Ondersteundende kabel types:	Cat5, Cat6, Cat7
Extended display identification data (EDID):	Ja
HDCP-passthrough:	Ja
Geen videocompressie:	Ja
Bedieningspaneel aan de voorzijde (TX):	Ja