Lightware WP-HDMI-TPS-RX97-EU Handleiding

Lightware AV extender WP-HDMI-TPS-RX97-EU

Lees hieronder de 📖 handleiding in het Nederlandse voor Lightware WP-HDMI-TPS-RX97-EU (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick Start Guide

WP-HDMI-TPS-RX97-EU, -EUROMOD, -UK, -US

FP-HDMI-TPS-RX97-GB3, -LEGRAND - CRFB

Further Information

The product brief and further information of this appliance is available at www.lightware.com.

See the section on the on the dedicated product page.Downloads

sales@lightware.com

+36 1 255 3800

support@lightware.com

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: v1.1

19200107

Important Safety Instructions

Please read the supplied safety instruction document before using the product and keep it

available for future reference.

Introduction

WP/FP-HDMI-TPS-RX97 series twisted pair HDBaseT

extenders provide

extension of uncompressed 4K/UHD video with embedded audio (up to eight

channel PCM or HBR audio) for long distances over a single CATx cable.

The thoroughly redesigned form factor of the wall and oor panels allows for easier

connecting and removing cables in narrow spaces (behind TV sets, under oor panel lids)

and reduces cable bending and breaking. The built-in cable tie-down points further ensure

stable connection and reduce cable stress.

Box Contents

Receiver unit Safety and Warranty info,

Quick Start Guide

Phoenix combicon

3-pole connector

Status LEDs The LEDs give feedback about the state of the unit and the

video signals. See Status LEDs for the details.

IR input/output 2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the

detector, IR OUT for the emitter).

RS-232 connector 3-pole Phoenix connector for RS-232 serial port. Firmware

upgrade can also be performed over this interface.

Ethernet Locking RJ45 connector for Ethernet communication.

HDMI output HDMI output for DVI or HDMI signal. Connect an HDMI

cable between the receiver and the display device.

TPS input port Locking RJ45 connector for HDBaseT

signal transmission.

Connect a twisted pair cable between the transmitter and the

receiver.

Tie-down point The built-in tie-down points are designed to clamp the

HDMI and the CATx cable and ensure stable connection.

Please see the enlarged picture below.

Front and Rear View (WP-HDMI-TPS-RX97-US)

Connecting Steps Status LEDs

SIGNAL

OFF: no video signal transmission is present.

ON: video signal transmission is present.

LINK

OFF: TPS connection failed between the devices.

BLINKING: TPS connection is detected and Low

Power Partial Functionality (LPPF) link mode is

active.

ON: TPS connection is detected and HDBaseT

(HDBT) or Long reach (LR) link mode is active.

LIVE

OFF: no power supply or out of order.

BLINKING: device is powered and ready to use.

Bottom View (WP-HDMI-TPS-RX97-US)

RS-232 Switch Modes



Please note that the 48V power adaptor is an optional accessory which can be purchased

separately.

RS-232 switch Normal: serial data is passed through the device.

Prog: RS-232 pass-through function is disabled, the device

is ready for the rmware upgrade (see RS-232 switch

modes section for details).

TPS mode switch LR: Longreach TPS mode; lower resolution (max 1080p),

longer distances.

Auto: TPS mode is determined automatically.

DC Input Connect the output to the 3-pole Phoenix connector on the

bottom of the wall plate.

CATx

Connect the TPS output port of the receiver to the port of the TPS+PoE

TPS-PI-1P1 by a CATx cable.

Connect the receiver (or the Matrix input board) to the power injector by a

CATx cable via the TPS port.

HDMI

Connect the sink (e.g. Projector) to the HDMI output port by HDMI cable.

RS-232

Optionally for RS-232 extension: connect a controller/controlled device

(e.g. Projector) to the RS-232 port.

Optionally for Infrared extension:

Connect the IR emitter to the IR OUT port of the receiver, and/or

Connect the IR detector to the IR IN port of the receiver.

LAN

Optionally connect the receiver to a LAN.

Power

Powering on the devices is recommended to do as the nal step during

the installation. Please check the Power Supply Options section for the

details.



WP-HDMI-TPS-RX97 series have the same connectors but the dimensions are different.

The product is compatible with any HDBaseT

third party devices.

HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

Power Supply Options

TPS-97 extenders are compatible with IEEE 802.3af standard - Power over Ethernet (PoE) -

and can receive power over the TPS line.

The extender can be powered by any of the following ways:

1. Local adaptor 2. Remote power injector 3. Matrix board



TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power

the WP-HDMI-TPS-TX/97 series and vica versa. WP-UMX-TPS-TX97 series contains PoE-

compatible remote power function (PD, Powered Device), RX95 and TX95 extenders can be

remote powered only by each other.



Warranty void if damage occurs due to the usage of a different power source.

Typical Application

HDMI

Compatible

Transmitter or

Input Board WP-HDMI-TPS-RX97

Power adaptor IR detector Ethernet

Power LAN

RS-232

WP-H DM I-T PS-R X97-US

HDMI OUTEthernet

TPS-PI-1P1

Power injector

CATxCATx

IR OUT

IR IN

LINK

TX RX

LIVE

SIGNAL

2 3 11 54

48V DC

Power

adaptor

TPS-PI-1P1 CATx

(TPS)

Power

send

48V DC

Power

adaptor

MX-TPS2-IB-P

DC IN

8 CH TPS INPUT BOARD WITH POE

48V 5A

- +

Ethernet

TPS IN 1 TPS IN 2 TPS IN 3 TPS IN 4

8CH INPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO

MX-HDMI-3D-IB-A

IN 1 IN 2 IN 3 IN 4

MX-TPS2-OB-S

48V 5A

DC IN

8 CH TPS OUTPUT BOARD WITH DIGITAL AUDIO

12V power on TPS c

TPS OUT 1 TPS OUT 2 TPS OUT 3 TPS OUT 4

8CH OUTPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO

MX-HDMI-3D-OB-A

OUT 1 OUT 2

CATx

(TPS)

External

power supply

Power send

ypical: 0.5A

Max: 1.25A

- +

Max:2.5A

mm2 :NIP

IR OUT

IR IN

LINK

TX RX

LIVE

SIGNAL

WP-HDM I- TP S-RX 97-US

HD MI OUTEthern et

IR OUT

IR IN

LINK

TX RX

LIVE

SIGNAL

WP-HDM I- TP S-RX 97-US

HD MI OUTEthern et

IR OUT

IR IN

LINK

TX RX

LIVE

SIGNAL

WP-HDM I- TP S-RX 97-US

HD MI OUTEthern et

Compatible Devices

TPS-97 extenders are compatible with all Lightware devices with TPS port except the TPS-90

series.

IR cable

Serial

cable

IR emitter

HDMI

Blu-Ray or DVD Player

LAN

Ethernet switch

HD Projector

Touch panel

Sn:

Made in EU, H ungary

RoHS

Ethernet 10/100

Bidir ectional IR

Bidir ectional RS-232

TTPPSS LLoonngg DDiissttaannccee TTrraannssmmiitttteerr

HDMI, 3D, 4K suppor ted

For best performance use AW G23 CAT6 o r CAT 7 SFTP cable

PIN: 2 mm

12V 1A DC

I--T

PS --T

X97

Device can be remote po wered over TPS link with PoE

(IEEE 802.3af)

TPS OUT PoE( )

TPS-PI-1P1

LAN

HDMI-

TPS-TX97

48V DC

Power

adaptor

LAN

IR detector

HDMI

IR cable

Serial cable

ETHE RNET

Laptop

WP-HDMI-TPS-RX97-US

Typical: 0.5A

Max: 1.25A

- +

Max:2.5A

mm2 :NIP

IR OUT

IR IN

LINK

TX RX

LIVE

SIG NAL

WP-HDM I-TPS-RX97-US

HDMI OUTEtherne t

CATx

TPS connection

CATx up to 170m

Power

send

WP-HDMI-TPS-RX97-US

HDMI OUTEthernet

Wiring Guide for RS-232 Data Transmission

WP/FP-HDMI-TPS-RX97 series are built with 3-pole Phoenix connector. See the below

examples of connecting to a DCE (Data Circuit-terminating Equipment) or a DTE (Data

Terminal Equipment) type device:

Lightware device and a DCE

D-SUB 9 - Phoenix

Lightware device and a DTE

D-SUB 9 - Phoenix

TX RX

2: TX data transmit

3: RX data receive

5: Ground

TX RX

2: TX data receive

3: RX data transmit

5: Ground

For more information about the cable wiring see the user’s manual of the device or

Cable Wiring Guide on our website www.lightware.com/support/guides-and-white-papers.

LINKLIVE

SIGNAL

LINKLIVE

SIGNAL

LINKLIVE

SIGNAL

Safety and

Warranty

Info

Quick

Start

Guide

IR IN

SIGNAL

HDMI OUT

Dimensions Maximum Extension Distances

Below values are valid when the receiver is powered by a local adaptor; distances may

decrease depending on the powering mode (local or remote) and cable quality.

Resolution Pixel

clock rate

Cable lengths

(Auto / Long reach TPS mode)

CAT5e

AWG24

CAT7

AWG26

CAT7

AWG23

1024x768@60Hz 65 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*

1280x720p@60Hz 73.8 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*

1920x1080p@60Hz (24bpp) 148.5 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*

1920x1200@60Hz 152.9 MHz 100 m / NA 90 m / NA 120 m / NA

1600x1200@60Hz 162 MHz 100 m / NA 90 m / NA 120 m / NA

1920x1080@60Hz (36bpp) 70 m / NA 70 m / NA 120 m / NA222.75 MHz

3840x2160@30Hz UHD ** 297 MHz 70 m / NA 70 m / NA 100 m / NA

4096x2160@30Hz 4K ** 297 MHz 70 m / NA 70 m / NA 100 m / NA

* Long reach TPS mode supports pixel clock frequencies up to 148.5 MHz.



CAT7 SFTP AWG23 cable is always recommended.

Mounting Options - WP-HDMI-TPS-RX97-US

Mounting Options - FP-HDMI-TPS-RX97-CRFB



CRFB Floorbox is not supplied with the product.

Variant Dimensions (mm) Recommended outlet box type

for mountinga b c1c2

WP-HDMI-TPS-RX97-EU 80 150 24.38 33.72 European two gang panel

Part no.: 77190-D3

WP-HDMI-TPS-RX97-UK 80 140 24.38 33.72 Appleby galvanised steel

knockout boxes 2g 47mm

Faceplate (for EUROMOD):

CE Double Gang Flat Faceplate

Part no.: QFP-QTM

WP-HDMI-TPS-RX97-EUROMOD 49.6 99.6 28.76 29.4

WP-HDMI-TPS-RX97-US 114.3 115.9 24.46 33.64 B225R

FP-HDMI-TPS-RX97-GB3 44.8 134.5 31.5 26.63

OBO Bettermann: UT4

Part no.: 7408727

Cover plate: OBO Bettermann

UT4 P3 Part no.: 7408 76 1

FP-HDMI-TPS-RX97-LEGRAND 44.8 134.5 31.5 26.63 Legrand 896_10

FP-HDMI-TPS-RX97-CRFB 69.8 113.2 39.6 21.53 Legrand CRFB

Bidirectional Pass-through Data Lines

The direction of the video extension is xed

from TX towards RX but the pass-through data

lines are bidirectional*. It means the RS-232,

IR, Ethernet source and sink devices can be

connected either to the TX or to the RX and the

signal is transmitted to the other extender.

* In fact IR transmission is uni-directional but

the extender has two IR channels with different

directions.

RS-232

Third party devices with standard RS-232 port are supported as the extenders work in „pass-

through” mode. TX and RX provide 3-pole Phoenix connector. The RS-232 options – the baud

rate and the parity bits are set on the third party devices and it can be anything. The extenders

support any kind of serial settings.



Please nd the RS-232 device type in its user guide; the extenders work as DCE devices.

Ethernet

The Ethernet port on the RX or on TX can be connected to a LAN hub, switch or router with a

LAN cable. The other side behaves as an Ethernet uplink port. The extenders support 10/100

Mbps data transfer rate. The Ethernet port has auto crossover function. It is able to recognize

and handle both cable types: patch and cross TP cables.

Infrared (IR)

One emitter and one detector is enough for remote controlling one IR sink device. If there

is an IR sink device to be controlled next to the TX and the other one is next to the RX, two

emitter-detector pairs are needed. The IR emitter and the detector have standard 3.5 mm TRS

(jack) connectors. The emitter’s plug has two poles (mono) and the detector’s plug has three

poles (stereo).



The emitter and detector pair is not supplied with the product, it can be ordered from

Lightware separately.

Types of IR Connectors (1/8” TS / TRS )

1 2 3

1 2-3

Detector – 3-pole-TRS Emitter – 2-pole-TS

1 Tip 1 TipSignal (active low) +5V

2 Ring 2 RingGND Signal (active low)

3 Sleeve 3 Sleeve+5V

TPS Link Modes

The TPS working mode between the transmitter and the receiver parties is determined by

the mode set in them. Both parties inuence on the setting which determines the nal TPS

transmission mode. The following TPS modes are dened:

Long reach (LR): Longer CATx cable length, less bandwidth (limited resolution). The

LPPF mode is not available in LR TPS link mode.

HDBaseT

(HDBT): more bandwidth (higher resolutions), shorter CATx cable length. If

no video present, the units change to LPPF mode automatically.

Low Power Partial Functionality (LPPF): Only Ethernet, RS-232 and IR are extended.

Toggling between TPS link modes

The toggle switch on the extenders can

be used to toggle between the LR and

Auto TPS modes. If both units have Auto

state and there is valid video signal on

the transmitter the common mode will

be HDBT. If the video signal disappears

devices go into LPPF mode.

TPS mode between an extender and a

port of a matrix board

If an extender and a TPS matrix board are paired the board forces the extender to use the

settings of the matrix. The extender’s TPS mode switch has no effect.



Always use the Auto mode with third-party devices!

The negotiated

TPS working mode

Selected mode (RX)

LR Auto

Selected

mode

(TX)

LR LR LR

Auto LR HDBT

Mounting Options - FP-HDMI-TPS-RX97-GB3

This example shows how to mount the FP-HDMI-TPS-RX97-GB3

receiver easily into an industrial standard box (GB3 mounting box is not

supplied with the product, it can be purchased separately).

Release and remove the xing screws of the rear frames from the

extender.

Insert the extender into the GB3 P3 frame.

Put back the rear frame on the extender and position it to get the

holes aligned.

Fasten the rear frame on the extender by the tting all the screws.

12-3



Mounting of FP-HDMI-TPS-RX97-Legrand variant is really similar to this method.



Mounting of another variants of WP-HDMI-TPS-RX97 series are really similar to this method.

Thanks to the design of Lightware devices, WP-HDMI-TPS-RX97-US receiver can

be mounted easily into an industrial standard box as the gures show below. B225R

switch/outlet box is not supplied with the product, it can be purchased separately.

Release and remove the xing screws from the front side of the extender.

Insert the extender into the B225R outlet box and position it to get the holes aligned.

Fasten the front side of the extender to the B225R outlet box by tting all

the screws.

Ventilation



To ensure the correct ventilation and avoid overheating

mount the extender into an industrial standard switch/outlet

box. Let enough free space in front of the appliance and

keep the ventilation holes free.

The picture on the right side shows the direction of the airow.

OUT

Specications

General

Compliance CE ...............................................................................................................

EMI / EMC EN 55035:2017 / EN 55032:2015 ...............................................................

Cooling ................................................................................................. by a cooling fan

Weight ........................................................................................................approx. 370g

Power

Power supply external power adaptor / PoE (IEEE 802.3af) via TPS ..........................

Power adaptor Input 100-240 V AC 50/60 Hz, Output 48V DC, 0.5 A .........................

Power consumption 6.5W (typ) / 8W (max) ...................................................................

Connectors

RX input RJ45 (TPS interface) ........................................................................................

RX output HDMI connector ..............................................................................................

Ethernet RJ45 .................................................................................................................

IR input, output 3.5 mm (1.8”) jack connector ................................................................

Serial port 3-pole Phoenix ................................................................................................

TPS port (HDBaseT

-compatible)

Ethernet / RS-232 / IR pass-through yes .......................................................................

Power ......................................................................................................2-pole Phoenix

Digital video signal

Supported signals DVI 1.0, HDMI 1.4 ...........................................................................

Signal standard DVI and HDMI standard which supports embedded audio ................

Supported resolutions up to 4K / UHD (30Hz RGB 4:4:4, 60Hz YCbCr 4:2:0) ..............

............................................................................................1920x1080@120 Hz, 24 bit

3D support yes ...............................................................................................................

HDCP compliant yes ......................................................................................................

Control over CEC yes, only in the HDMI signal ..............................................................

EDID support transparent ..............................................................................................

Equalization .................................................................................... adaptive, automatic

Product specificaties

Merk:	Lightware
Categorie:	AV extender
Model:	WP-HDMI-TPS-RX97-EU
Kleur van het product:	Zwart
Gewicht:	330 g
Breedte:	100.4 mm
Diepte:	100.4 mm
Hoogte:	26 mm
Soort:	AV-receiver
LED-indicatoren:	Ja
Bluetooth:	Nee
Stroom:	2.5 A
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Maximum resolutie:	4096 x 2048 Pixels
Certificering:	CE
HDCP:	Ja
Aansluiting voor netstroomadapter:	Ja
3D:	Ja
Materiaal:	Metaal
HDMI versie:	1.4a
Ondersteunde grafische resoluties:	1920 x 1080 (HD 1080)
Remote (IR) ingang:	1
Remote (IR) uitgang:	1
Ophangsysteem voor aan de muur:	Ja
Power over Ethernet (PoE):	Ja
IR-doorvoer:	Ja
Bandbreedte:	3.4 Gbit/s
Aantal HDMI-uitgangen:	1
Seriële poort(en):	1
Operating voltage:	12 V
Wifi:	Nee
Stroomverbruik (typisch):	5.3 W
Consumer Electronics Control (CEC)-ondersteuning:	Ja
Ondersteundende kabel types:	Cat5, Cat6, Cat7
Stroomverbruik (ontvanger) (max):	6.1 W
HDCP-passthrough:	Ja
Geen videocompressie:	Ja
RS-232-passthrough:	Ja
EDID-geheugen (TX):	Ja
EDID-emulatie (TX):	Ja