Lightware DVI-TP-RX100 Handleiding

Lightware AV extender DVI-TP-RX100

Lees hieronder de 📖 handleiding in het Nederlandse voor Lightware DVI-TP-RX100 (1 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Quick Start Guide

DVI-TP-RX100

DVI-TP-TX200

DVI-TP-TX300

Further information

The document is valid with the following rmware version: 1.1.5 for RX and 1.2.9 for TX.

The User’s manual of this appliance is available at www.lightware.eu.

See the Downloads section on the website of the product.

sales@lightware.eu

+36 1 255 3800

support@lightware.eu

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 1.0

19200011

Important safety instructions

Please read and keep the information in the attached safety instructions supplied with the

product before start using the device.

Introduction

DVI-TP-TX200/TX300 and DVI-TP-RX100 are Single Link DVI over Twisted Pair extenders

which allow video signals of up to 1920x1200@60Hz or 2048x1080@60Hz resolution to be

transmitted through 50 meters of high quality CAT7 cables. Accessible distances depend on

the used cable quality and signal resolution.

DVI-TP-TX200 and DVI-TP-TX300 transmitters include an EDID Manager and built-in DVI

distribution amplier for local monitor output. Only one CATx cable is needed for DVI signal

transmission, there is no need for second CAT cable. Beside the local DVI output TX200

provides one and TX300 provides two identical CATx outputs. TX300 allows transmission of

DVI signal to three different remote displays including local monitor.

Box contents

Powering on

1. After the system is complete, rstly connect the output of the Power Adaptor to the

extenders, then secondly to the AC power socket.

2. At rst the extenders display the rmware version using the upper two LEDs. The

following example shows this process for a rmware version of 1.2.9:

RED blinks once, short pause.

GREEN blinks twice, short pause.

GREEN blinks nine times.

3. The EDID INVALID LED on the transmitter lights up for 2-3 seconds, then turns green if

the selected EDID is valid, or remains red, if the selected EDID is invalid (or the selected

memory is empty).

4. The attached DVI source and monitor(s) can be powered on.



If none of the LEDs light up upon power-up, the unit is most likely damaged and further

use is not advised. Please contact support@lightware.eu.

Adjusting the input equalization

The amplitude of high frequency signals decreases after they pass through long distances

in copper cables. To counter-act this phenomenon, RX100 amplies the signal while

maximizing the amplitude at a certain level. The RX100 offers two equalization modes:

automatic and manual. The mode can be toggled by pressing the EQ MODE SELECTION

button.



It is always advised to use the automatic mode and only adjust the equalization

manually if the auto mode does not give a good result.

Extender unit 5V DC power adaptor

with interchangeable plugs

Safety and warranty info,

Quick Start Guide

Front and rear view - Transmitter

EDID

rotary switches

The rotary switches select one of the EDID memory

addresses.

Learn EDID

button

Stores the EDID of the display device attached to the

output in the selected memory address.

Status LEDs The LEDs give feedback about the state of the units and

the video signal.

DVI input Connect one DVI-D or DVI-I cable (only digital pins are

connected internally) between the DVI source and the

transmitter.

Monitor output Connect one DVI-D or DVI-I cable (only digital pins are

connected internally) between the transmitter and the local

display device. The output connector is able to supply 500

mA current on pin 14 to power ber optical DVI extenders

like DVI-OPT-TX100.

CATx output(s) Connect one or two CAT5x cables between DVI-TP-TX200/

TX300 and the receiver (DVI-TP-RX100 or Lightware

Hybrid Matrix equipped with twisted pair input cards).

DC 5V input Connect the output of the supplied +5V DC power adaptor

or use Lightware’s rack mountable power supply.

Legend - Transmitter

Front and rear view - Receiver

Status LEDs The LEDs give feedback about the state of the units and

the video signal.

EQ mode

selector button

Toggles between automatic and manual EQ mode. The EQ

mode status LEDs indicate which mode is currently active.

EQ level adjust The 25-turn potentiometer can be used to precisely set

the right amount of equalization in manual EQ mode.

The potentiometer does not stop at the end positions,

but rotates indenitely. After reaching the end position, a

clicking sound can be heard at every full turn of the knob.

CATx input Connect one CATx cable between DVI-TP-RX100 and the

transmitter (DVI-TP-TX200/TX300 or Lightware Hybrid

Matrix equipped with twisted pair output cards).

DVI output Connect one dual link DVI-D or DVI-I cable (only digital

pins are connected internally) between the receiver and

the local display device. The output connector is able to

supply 500 mA current on pin 14 to power ber optical DVI

extenders like DVI-OPT-TX100.

DC 5V input Connect the output of the supplied +5V DC power adaptor

or use Lightware’s rack mountable power supply.

Legend - Receiver



DVI-TP-TX200 contains only one CATx output.



The extenders do not have networking capabilities. Do not connect the extenders

to a Local Area Network device or a PC via the RJ45 sockets. Doing so may damage

the unit!

Status LEDs - Transmitter

EDID INVALID

BLINKING: invalid EDID is read from the connected sink or EDID learning failed.

ON: invalid EDID is selected by the rotary switches.

EDID VALID

BLINKING: valid EDID is received from the connected sink or EDID learning is successful.

ON: valid EDID is selected and emulated by the rotary switches.

MONITOR

ON: a sink is connected to the Monitor output port and sends a valid Hot plug signal.

SRC +5V

ON: a DVI source is connected, powered on and sends the +5V signal.

Status LEDs - Receiver

MANUAL EQ

ON: Manual equalization mode is active.

AUTO EQ

ON: Auto equalization mode is active.

SIGNAL PRESENT

ON: a valid DVI clock signal is present on the CATx (video) input port.

MONITOR HOTPLUG

ON: a sink is connected to the DVI output port and sends a valid Hot plug signal.

EDID selection

Use a at head screwdriver to change the address. The left switch

sets the tens value, the right switch gives the ones value of the EDID.



Avoid the use of keys, coins, knives and other sharp objects.

Maximum twisted pair distances

Resolution Vfreq

(Hz)

Pixel clk

freq. (MHz)

Cat5e

UTP

Cat6

UTP

Cat6

FTP

Cat7

S/FTP

640x480 60 25.2 60 m 65 m 70 m 80 m

800x600 60 40.0 60 m 65 m 65 m 75 m

1024x768 60 65.0 55 m 60 m 60 m 75 m

1280x720p 60 74.2 55 m 60 m 60 m 70 m

1280x1024 60 108.0 50 m 55 m 60 m 65 m

1400x1050 60 121.8 45 m 45 m 55 m 60 m

1600x1200 60 162.0 30 m 35 m 45 m 50 m

1920x1080p 60 148.5 30 m 35 m 45 m 50 m

1920x1200p 60 153.0 30 m 35 m 45 m 50 m

Integrated system application



Category 7 cable is always recommended since they are screened and foiled by standard.

Safety and

warranty

info

Quick

Start

Guide

1 2 3 4

5 76

1 32

4 5 6

Product specificaties

Merk:	Lightware
Categorie:	AV extender
Model:	DVI-TP-RX100
Kleur van het product:	Zwart
Gewicht:	230 g
Breedte:	100.4 mm
Diepte:	67.6 mm
Hoogte:	26 mm
Soort:	AV-receiver
LED-indicatoren:	Ja
Bluetooth:	Nee
Stroom:	1 A
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Ondersteunde video-modi:	720p, 1080i, 1080p
Maximum resolutie:	2048 x 1080 Pixels
Inclusief AC-adapter:	Ja
Vermogensverbruik (max):	6 W
Aansluiting voor netstroomadapter:	Ja
Materiaal:	Metaal
Ondersteunde grafische resoluties:	1024 x 768 (XGA), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA), 2048 x 1080
Externe adapter:	Ja
Output current:	2.5 A
DVI output ports:	1
Bandbreedte:	1.65 Gbit/s
Operating voltage:	5 V
Maximaal bereik:	65 m
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Stroomverbruik (typisch):	3 W
Ondersteundende kabel types:	Cat5, Cat6, Cat7
Extended display identification data (EDID):	Ja
HDCP-passthrough:	Nee