Lightware DVI-OPT-RX110 Handleiding

Lightware AV extender DVI-OPT-RX110

Lees hieronder de 📖 handleiding in het Nederlandse voor Lightware DVI-OPT-RX110 (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick Start Guide

DVI-OPT-RX110

DVI-OPT-TX110

Further Information

The document is valid with the following rmware version: 1.1.6

The Product brief and further information of this appliance is available on www.lightware.com.

See the Downloads section on the website of the product.

sales@lightware.com

+36 1 255 3800

support@lightware.com

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 2.1

19200072

Important Safety Instructions

Please read and keep the information in the attached

safety instructions supplied with the product before start

using the device.



The extenders are Class 3R laser products.

Introduction

DVI-OPT-TX110 and DVI-OPT-RX110 pair is a DVI to ber transmitter / receiver set for

up to 2500 m distance transmission. Using Single Fiber Technology the DVI-D signal is

transmitted over only one multimode 50/125 ber core. Sources and display devices are

galvanically isolated against ground loops and hum effects, and no delay occurs in the

signal, the video image is transported without any frame latency.

Box Contents

Legend - Transmitter

Legend - Receiver

DVI input Connect to a DVI source for transmitting a DVI signal or

connect to a sink device for learning the EDID; see the

Learning an EDID section.

Power LED The LED lights green if the power supply is sufcient (DVI

or external adaptor supply).

EDID LED Three-colored LED displays EDID status. See legend for

indications.

Learn button Press the button for 2 seconds to activate mode. Learn

Press for 10 seconds to restore factory default EDID.

Power connector Barrel plug receptacle for external power adaptor.

Fiber connector SC type receptacle for multimode ber output.

Using the LEARN button (Transmitter)

When the button is pressed the EDID state LED turns off to indicate the button press.

If the button is released sooner than 2 seconds, the press will be ignored.

If the button is pressed for more than 2 seconds, the EDID learn mode gets activated

for a period of 10 seconds.

If the button is pressed for more than 10 seconds and the unit is not connected to a

display device, the factory default EDID will be restored.

EDID status LED legend (Transmitter)

Learning an EDID (Transmitter)

1. Plug in the power adaptor to an electrical outlet, or plug in the enclosed USB power

cable to an USB connector, and then connect the DC cable to the transmitter.

2. The power and the EDID state LEDs light up.

3. Press and hold down the LEARN button for two seconds. The EDID state LED goes

dark, and then lights up orange to indicate that learn mode is activated.

4. Connect the transmitter to a display device; the learn mode is active for 10 seconds.

5. The transmitter reads the EDID from the display device. Do not disconnect the device

while it lights orange (approximately 10 seconds).

6. Check if the learning succeeded:

a. If the learning process was successful, the EDID state LED blinks slowly green for

8 seconds. The stored EDID is changed.

b. If the learning process failed, the EDID state LED blinks slowly red for 8 seconds.

The previously stored EDID remains in memory.

c. The EDID state LED changes continuous green or red depending on the validity

of the stored EDID.

7. Disconnect the transmitter (if still connected) and the power supply. The stored EDID

remains in memory until it is overwritten. The unit is ready to be used for DVI signal

extension.

Top View - Transmitter

Top View - Receiver

Extender unit USB cable with

1.35/3.5 mm plug

5V DC power adaptor

with interchangeable plugs

Safety and warranty info,

Quick Start Guide

Safety and

Warranty

Info

Quick

Start

Guide

DVI output Connect to DVI display.

Power LED Lights green if the unit is powered on.

Hotplug LED Indicates that the display device is connected correctly.

Laser LED Green light indicates that the laser is properly detected on

the optical input.

Power connector Barrel plug receptacle for external power adaptor.

Fiber connector SC type receptacle for multimode ber input.

OPT

Connect a multimode SC ber cable to the SC MM IN connector on the RX110

unit.

DVI

Connect the receiver to the DVI sink (e.g. monitor).

Power

Power on the DVI sink (monitor).

OPT

Connect the other end of the multimode SC ber cable to the SC MM OUT

connector on the transmitter (TX110) unit.

DVI

Connect the transmitter to a DVI source (e.g. computer).

Power

Power on the DVI source (computer). It reads the EDID from the transmitter,

and outputs the video signal according to the set resolution.

Check the LEDs on the transmitter:

a. If both the power LED and the EDID status LEDs are green, the

transmitter is ready to use.

b. If the power LED does not light up, the DVI source does not send

enough power through the DVI connector, so the external power

adaptor or the special USB power cable needs to be connected to

the transmitter.

c. If the EDID state LED lights red, an EDID has to be learned.



After powering on the TX110 unit shows its three digit rmware version with red, green and

orange blinks (FW 1.1.6 is: 1x red, 1x green, 6x orange).

LED light Meaning

GREEN continuous EDID valid

RED continuous EDID invalid

ORANGE continuous EDID learn mode active

GREEN blinking EDID learn success

RED blinking EDID learn failed

ORANGE fast blinking Reloading factory EDID

ORANGE slow blinking Laser module failure

Power

Powering options: DVI-OPT-RX110/DVI-OPT-TX110

Power adaptor

USB cable

DVI connector (via +5V pin)

Monitor

DVI-OPT-RX110

DVI-OPT-TX110

Power

DVI OPT

POWER

TRANSMITTER

DVI

POWER

HOTPLUG

RECEIVER

INVISIBLE LASER RADIATION

AVOID DIRECT EYE EXPOSURE

CLASS 3R LASER PRODUCT

Radiated wavelengths:

778 nm, 800 nm, 825 nm, 850 nm

Output power <= 1mW

Classified by EN 60825-1:2008

Connecting Steps

Restoring the Factory Default EDID (Transmitter)

1. Power up the transmitter by

a. using one of the external power supply

b. connecting it to a DVI source.

2. Press and keep the LEARN button pressed. The EDID state LED goes dark for two

seconds, and then turns continuous orange to indicate that learn mode is activated.

(Do not connect the unit to a display device.)

3. Keep the button pressed until the LED starts to blink orange (after approximately

10 seconds). Five blinks indicate the EDID restore process.

4. After the restore process is nished, the LED blinks slowly green for 8 seconds. The

stored EDID is changed back to factory default (

1920x1200 @ 59.55Hz

5. The unit is ready to be used for DVI signal extension.

Troubleshooting

Some DVI sources may not supply enough power to the transmitter. Use one of the

external power supply methods in this case.

If the image is noisy make sure that the ber cable plugs are clean.

Typical Standalone Application

Maximum Extension Distances

OM1

(62,5/125)

OM2

(50/125)

OM3

(50/125)

OM4

(50/125)

1080p@60Hz 24 bpp 250 m 600 m 1200 m 2500 m

Video Signal

Supported video signal ......................................................................................... DVI-D

Maximum resolution .................................................1920 x 1200 or 2048 x 1080 pixel

Data rate ..............................................................................................1.65 Gbps/ color

Video delay .............................................................................................none (0 frame)

EDID emulation........................................................................Yes, with LEARN button

EDID memory ................................................................1 pc user programmable EDID

Factory EDID .............................................................................. 1920x1200 @ 59.55Hz

Optical

Optical cable .....................................................................................multimode, 50/125

Optical connector .......................................................................................................SC

Laser class specication..................................................................................Class 3R

Laser wavelengths .................................................. 4 channel: 778; 800; 825; 850 nm

DVI-OPT-TX100 output OMA* ...........................................................-6.25 dBm (max.)

DVI-OPT-RX100 OMA* sensitivity ...................................................-14.25 dBm (max.)

Maximum transmission distance ...................... 2500m (using OM4 type optical cable)

*Optical Modulation Amplitude

Specication

General

Compliance ................................................................................................................CE

EMI / EMC ................................................................................. EN 55024 / EN 55032

Cooling. ...............................................................................................................passive

Weight (DVI-OPT-TX110 / DVI-OPT-RX110) ..............................................200g / 205g

Size. .............................................................................. 100.4 mm x 67.6 mm x 26 mm

Material ................................................................................................................... steel

Warranty .............................................................................................................3 years

Power

Power supply ........................................................................... external power adaptor

Power adaptor .............................................. (100 - 240 V AC, 50/60 Hz)(5V DC, 1 A)

Power connector ............................................................................ 1.35 / 3.5 mm barrel

Power consumption (DVI-OPT-TX110 / DVI-OPT-RX110) ..................... 1.4 W / 0.8 W

Connectors

DVI-OPT-TX110 input ................................................................................24-pole DVI-I

DVI-OPT-TX110 output................................................................................SC simplex

DVI-OPT-RX110 input .................................................................................SC simplex

DVI-OPT-RX110 output .............................................................................24-pole DVI-I

MX-DVI-OPT-IB-LC

8CH OPTICAL INPUT BOARD

LASER DETECT

RECEIVE R ACTIVE

SIGNAL PRESENT

L. D.

R. A.

SIGNAL

IN1 IN2 IN7 IN8

IN5 IN6

IN3 IN4

SC 50/12 5 MULTIMO DE

8CH OPTICAL INPUT BOARD

SC 50/12 5 MULTIMO DE

8CH OPTICAL INPUT BOARD

IN1 IN2 IN7 IN8

IN5 IN6

IN3 IN4

LASER DETECT

RECEIVE R ACTIVE

SIGNAL PRESENT

MX-DVI-OPT-IB-ST

4 CH DUAL L INK DVI INPUT BOARD

MX-DVIDL -IB

LC 50/1 25 MUL TIMODE

LASER DETECT

RECEIVE R ACTIVE

SIGNAL PRESENT

L. D.

R. A.

SIGNAL

IN1 IN2

IN7 IN8

IN5 IN6

IN3 IN4

IN1 IN2 IN7 IN8

IN5 IN6

IN3 IN4

LASER DETECT

RECEIVE R ACTIVE

SIGNAL PRESENT

MX-DVI-OPT-IB-SC

OUT1 OUT2 OUT7 OUT8

OUT5 OUT6

OUT3 OUT4

8CH OPTICAL OUTPUT BOARD

SC 50/12 5 MULTIMO DE

MX-DVI-OPT-OB-ST

LASER DETECT

SIGNAL PRESENT

L. D.

SIGNAL

MX-DVI-TP-OB

8CH OPTICAL R ECLOC KING

OUTPU T BOA RD

MX-DVI-OPT-OB-NT

LASER DETECT

SIGNAL PRESENT

L. D.

SIGNAL

OUT1 OUT2

OUT7 OUT8

OUT5 OUT6

OUT3 OUT4

MX-DVI-OPT-OB-LC

8CH OPTICAL OUTPUT BOARD

LASER DETECT L. D.

L. D.

OUT1 OUT2 OUT7 OUT8

OUT5 OUT6

OUT3 OUT4

LASER DETECT

MX-DVI-OPT-OB-SC

OUT1 OUT2 OUT7 OUT8

OUT5 OUT6

OUT3 OUT4

RS-232

LOCAL CONTRO L

RoHS

Made in EU, HU

Service LAN

SC MM OUT DC 5V

Integrated System Application

Product specificaties

Merk:	Lightware
Categorie:	AV extender
Model:	DVI-OPT-RX110
Kleur van het product:	Zwart
Gewicht:	95 g
Breedte:	39 mm
Diepte:	87.5 mm
Hoogte:	15.4 mm
Soort:	AV-receiver
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Bedraad
Ondersteunde video-modi:	1080p
Maximum resolutie:	2048 x 1080 Pixels
Inclusief AC-adapter:	Ja
Certificering:	CE
Aansluiting voor netstroomadapter:	Ja
Materiaal:	Aluminium
Ondersteunde grafische resoluties:	1920 x 1200 (WUXGA), 2048 x 1080
Output current:	1 A
Bandbreedte:	1.65 Gbit/s
Maximaal bereik:	2500 m
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Stroomverbruik (typisch):	0.8 W
Vezel-optische connector:	SC
Draad modus structuur:	Multimode
Extended display identification data (EDID):	Ja
Ondersteunde golflengten:	778,800,825,850 nm
EDID-geheugen (TX):	Ja
EDID-emulatie (TX):	Ja
OMA-ontvanger gevoeligheid:	-14.25 dBm