LevelOne FEP-0311 Handleiding

LevelOne Schakelaar FEP-0311

Lees hieronder de 📖 handleiding in het Nederlandse voor LevelOne FEP-0311 (2 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

FEP-0311

3-Port Fast Ethernet PoE Switch, 2

PoE Outputs

User s Manual ’

FCC Warning

This device has been tested and found to comply with limits

for a Class A digital device, pursuant to Part 15 of FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial environment.

This equipment generates and radiates radio frequency

energy and, if not installed and used in accordance with

the user’s manual, it may cause interference in which case

users will be required to correct interference at their own

expenses.

CE Mark Warning

This is a Class A product. In a domestic environment, this

product may cause radio interference in which case the

user may be required to take adequate measures.

Energy Saving Note of the Device

This power required device doesn t support Standby ’

mode operation. For energy saving, please remove the

power cable to disconnect the device from the power

circuit. Without removing power cable, the device will

consume power from the power source.

WEEE Warning

Package Contents

Thank you for purchasing our FEP-0311 series PoE

Switch.

Before installation, please check the contents of your

package for the following parts:

1. FEP-0311 x 1

2. User s Manual x 1 ’

3. Power Adaptor x 1

4. Power cord x 1

5. Rubber Feet x 4

Product Introduction

The FEP-0311 series is a 2-Port Adjustable 10/100Mbps

802.3af/at Power over Ethernet + 1-port 10/100Mbps

Uplink switch with a total power of / /90 watts. 36 65

FEP-0311 series features IEEE 802.3af and IEEE 802.3at

High Power PoE capabilities that offer a combined power

output of upto 30w over Cat.5e/6 Ethernet cable. FEP-

0311 series is flexible to adjust PoE on/off via DIP switch

on device itself. Meanwhile, the PoE output could supply

60 watts. max. to powered device when only one PoE port

is enabled. Furthermore, users could also extend wire

coverage up to 600 meters with PoE extender or PoE

repeater in the network.

Key Features

。Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u,

100BASE- TX

。Complies with IEEE802.3af/at Standard

。3-Port 10/100Mbps Fast Ethernet Switch

。2-Port supports Power over Ethernet

。Supports PoE power up to watts for each PoE port 50

。External Power / /90Watts 36 65

。Could supply 50 watts max. PoE output when one only

PoE port is enabled

。PoE on/off selectable via a DIP switch on the unit

。Over Current Protection / Over Temperature Protection /

Over Voltage Protection

。Remote power feeding up to 100meters

。Could extend up to 600 meters with PoE Extender or

PoE Repeater in the network

。Made of metal and desktop / wall-mount design

To avoid the potential effects on the environment and

human health as a result of the presence of

hazardous substances in electrical and electronic

equipment, end users of electrical and electronic

equipment should understand the meaning of

crossed-out wheeled bin symbol. Do not dispose of

WEEE as unsorted municipal waste; WEEE has to

be collected separately.

Hardware Installation

1. Plug the included power cord into device and the

other end into an electrical socket. The “Power” LED

will be on

2. Connect other switch / PC / device to Uplink port.

“Uplink” LED is on

3. ed Connect your IEEE802.3af/at compliant Power

Devices (PD) to port 1 to 2 and the Switch will

automatically supply power through these ports.

Now, “L PoEAN” “ and ” LED indicator are on.

Note: The device provides Physical DIP Switch to control PoE

on/off. When the DIP switch is set at off location, it will send data “ ”

only. However, if the DIP switch is set at location, it will deliver “on”

power and data together to PD devices. is suggested set DIP It to

switch before plug-in Ethernet Cable.

4. Ensure Powered device is on not, please make . If

sure all Ethernet cables are connected correctly and

tightly.

Note: The device is a power-required device, meaning it won ’t work

till it is powered. If your networks should be active all the time, please

consider using UPS (Uninterrupted Power Supply) for your device. It

will prevent you from network data loss or network downtime. In

some areas, installing a surge suppression device may also help to

protect your FEP-0311 from being damaged by unregulated surge or

current to the FEP-0311.

LED Indicators

Note: There are three different LED behaviors when FEP-0311 series connects

to PoE device or non-PoE device.

Application Diagram

Product Specification

Standard IEEE 802.3 10Base-T

802.3u100Base-TX / 100Base- IEEE FX

IEEE 802.3x flow control and back pressure

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

Copper Ports 3 10/100BASE-T RJ45, auto-MDI/MDI-X

PoE Injector Port 2 ports with 802.3at/af

Switch Architecture Store-and Forward

Address Table 4K entries,

Automatic source address learning

Share Data Buffer 48KB

Flow Control IEEE 802.3x pause frame for full-duplex

Back pressure for half-duplex

Filtering/Forwarding Rates 10Mbps port-14,880pps

100Mbps port-148,800pps

PoE Standard IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

PoE Power Supply Type Mid-span

PoE Power Output Per Port 56V DC, Max. 50 watts 48~

Power Pin Assignment 4/5(+), 7/8(-)

Total Power / / watts 36 65 90

LED Indicators Power plink LAN 2 / PoE 1~2 / U / 1~

Dimension (W x D H) 23 x 90 x 56 x mm

Power Requirement -56VDC / -60Hz External Power Adapter 48 50

Certification FCC/CE

Operating Environment Operating temperature: 0 40°C –

Storage temperature: - 70°C 20 –

Humidity: 20 95% non-condensing –

Product specificaties

Merk:	LevelOne
Categorie:	Schakelaar
Model:	FEP-0311
Kleur van het product:	Zwart
Gewicht:	200 g
Breedte:	62 mm
Diepte:	90 mm
Hoogte:	27 mm
Gewicht verpakking:	1100 g
Breedte verpakking:	146 mm
Diepte verpakking:	222 mm
Hoogte verpakking:	78 mm
Gebruikershandleiding:	Ja
LED-indicatoren:	LAN,PoE,Power,Uplink
Type verpakking:	Doos
Inclusief AC-adapter:	Ja
Land van herkomst:	Taiwan
Certificering:	FCC Class B, CE
Netwerkstandaard:	IEEE 802.3,IEEE 802.3af,IEEE 802.3at,IEEE 802.3u,IEEE 802.3x
Temperatuur bij opslag:	-20 - 70 °C
Stroomspanning bescherming:	Over current,Over voltage,Overheating
Luchtvochtigheid bij opslag:	10 - 90 procent
Mean time between failures (MTBF):	190000 uur
Vermogenstoevoer inclusief:	Ja
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Ja
Switchingcapaciteit:	0.6 Gbit/s
MAC-adrestabel:	4000 entries
10G support:	Nee
Datastroombeheer:	Ja
Aantal basis-switching RJ-45 Ethernet-poorten:	3
Type basis-switching RJ-45 Ethernet-poorten:	Fast Ethernet (10/100)
Jumbo Frames ondersteuning:	Ja
Full duplex:	Ja
(Buitenste) hoofdverpakking hoogte:	252 mm
(Buitenste) hoofdverpakking breedte:	422 mm
(Buitenste) hoofdverpakking brutogewicht:	12000 g
(Buitenste) hoofdverpakking lengte:	310 mm
Hoeveelheid per (buitenste) hoofdverpakking:	10 stuk(s)
Buffergrootte:	384 KB
Auto-negotiation:	Ja
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Code geharmoniseerd systeem (HS):	85176990
Totaal Power over Ethernet (PoE)-budget:	90 W
Jumbo frames:	2000
Hoeveelheid Power over Ethernet (PoE) ports:	2
Ondersteundende kabel types:	Cat3,Cat4,Cat5
Vermogen per poort Power over Ethernet (PoE):	30 W
Packet forwarding rate (10 Mbps):	14880 pps
Packet forwarding rate (100 Mbps):	148800 pps