La Crosse Technology WT-5350U Handleiding


Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor La Crosse Technology WT-5350U (24 pagina's) in de categorie Wekkerradio. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24
Contents
Language Page
English 2
Franรงais 31
Spanish 61
FCC ID: OMO-01RX (receiver)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
WT-5350
Radio Controlled Projection Alarm
Instruction Manual
R
DATE
AL/ S E L
MO DE /
PROJECTIO N
R A D I O C O N T R O L L E D
+
GB P.2 GB
P.3
GB P.4 GB
P.5
TABLE OF CONTENTS
Topic Page
Inventory of Contents 4
About WWVB 5
Quick Set-Up Guide 6
Detailed Set-Up Guide
Battery Installation 7
Program Mode
Programming Sequence 10
Function Buttons 11
Time Zone Setting 11
Time Setting 12
Date Setting 13
12/24-Hour Mode 14
DST (Daylight Saving Time) Setting 15
Features & Operations
Features 16
Radio-Controlled Time and Date 16
Projection 18
EL. Back light 19
Time Alarm 20
Changing Display Mode 22
Maintenance & Care 23
Troubleshooting 24
Specifications 25
Warranty and Contact Information 26
INVENTORY OF CONTENTS
1) WT-5350 Alarm Clock
2) AC adapter/transformer
3) Instruction manual and warranty card.
ADDITIONAL EQUIPMENT (not included)
1) Two fresh 1.5V AA batteries (optional for alarm clock)
FEATURES OF PROJECTION ALARM
1. Radio-controlled time and date
2. Projection of time
3. EL. Back light
4. Three modes of date/second display
5. Alarm
ABOUT WWVB (Radio Controlled Time)
The NIST (National Institute of Standards and Technology-Time and Frequency
Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the
exact time signal continuously throughout the United States at 60 kHz. The signal
can be received up to 2,000 miles away through the internal antenna in the Projection
alarm. However, due to the nature of the Earth's Ionosphere, reception is very limited
during daylight hours. The Projection alarm will search for a signal every night when
reception is best.
The WWVB Projection alarm receives the time data from the NIST Atomic clock in
Boulder, Colorado. A team of atomic physicists is continually measuring every second,
of every day, to an accuracy of ten billionths of a second per day. These physicists
have created an international standard, measuring a second as 9,192,631,770
vibrations of a Cesium-133 atom in a vacuum. For more detail, visit http://www.boulder.
nist.gov/timefreq.htm. To listen to the NIST time, call (303)499-7111. This number
will connect you to an automated time, announced at the top of the minute in
"Coordinated Universal Time", which is also known as Greenwich Mean Time (GMT).
This time does not follow Daylight Saving Time changes. After the top of the minute,
a tone will sound for every second. It is possible that your Projection Alarm may not
be exactly on the second due to the variance in the quartz. However, the clock will
adjust the quartz timing over the course of several days to be very accurate; under .
10 seconds per day.
QUICK SET-UP GUIDE
1) Insert two AA batteries into the Projection alarm and/or plug into wall
2) Wait 10 minutes for WWVB reception.
3) If there is no WWVB reception, manually set the time and date (instructions
in the Program Mode).
4) Program the settings.
5) Mount the WT-5350 in a suitable location, where WWVB signal can be
received.
6) The projector will activate and remain on if the alarm clock is plugged in. If
only batteries are used, the projector will only be activated when a button is
pressed.
7) See the "Features" section for instructions on projection direction, etc.
DETAILED SET-UP GUIDE
BATTERY INSTALLATION
1. Remove the battery cover.
2. Observe the correct polarity and install 2 AA batteries.
3. In addition or instead of inserting batteries, the AC adapter can be used.
Simply plug the adapter into the receptacle on the bottom of the alarm
clock and then plug in adapter.
4. Replace the battery cover.
5. The projector will activate and remain on if the alarm clock is plugged in. If
only batteries are used, the projector will only be activated when a button
is pressed. The projection is a red light, not harmful under normal usage,
although care should be taken to not look directly into the light.
Note:
After the batteries have been installed a tone will sound and the LCD
(Liquid Crystal Display) will activate. The date and U.S. map will be
displayed and the time will appear as "-:--". The WWVB search is
automatically initiated and a tower icon appears and ๎‹ˆashes with the
time colon (no tower icon will appear if the WWVB is too weak to be
detected and the time display will remain on "-:--"). While the WWVB
search is being conducted various numbers will appear in the time
display. After 10 minutes, the Projection Alarm will either display the
WWVB time, or discontinue the search if the time is not found. If the
search is cancelled "-:--" will remain in the time LCD. The Projection
Alarm will conduct a WWVB search every hour until the ๎‹‡rst signal is
found. Once the WWVB time is found, a search is automatically
conducted nightly at midnight. If the signal is found at midnight,
the tower icon will appear. If not, another search will take place every
hour (until 6:00 am) until the signal is received successfully. If no signal
is found during this period, the tower icon will not appear and the clock
will search again at 12:00 am the next night.
PROGRAM MODE
To enter the Program Mode, hold down the "MODE+" button for 2 seconds, until the
time zone ("-5" default) flashes in the lower right. The Program Mode Guide is laid
out in a manner that allows you to program each function separately, or you can
follow the instructions entirely to program the Projection Alarm. Complete
programming is usually done for the initial set-up and will require you to skip step 1
of programming sections C through G. Press the "SNOOZE" button at any time to
exit the Program Mode or wait approximately 15 seconds for the Projection Alarm to
automatically return to normal operation.
AC adapter
receptacle
GB P.6 GB
P.7
GB P.8 GB
P.9


Product specificaties

Merk: La Crosse Technology
Categorie: Wekkerradio
Model: WT-5350U

Heb je hulp nodig?

Als je hulp nodig hebt met La Crosse Technology WT-5350U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Wekkerradio La Crosse Technology

Handleiding Wekkerradio

Nieuwste handleidingen voor Wekkerradio