La Crosse Technology WT-5120U Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor La Crosse Technology WT-5120U (24 pagina's) in de categorie Wekkerradio. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24
WT-5120
433 MHz
Radio Controlled Projection Alarm
R
Contents
Language Page
English 2
French 31
Spanish 60
Instruction Manual
FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS:
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
FCC DISCLAIMER
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Topic Page
Features & Operations
Features 15
Radio-Controlled Time 16
Projection 17
LED Backlight 18
Indoor Temperature 18
Indoor Humidity 18
Remote Temperature 19
Time Alarm 20
Changing Display Mode 21
Mounting 21
Maintenance & Care 23
Troubleshooting 23
Specifications 26
Warranty and Contact Information 27
TABLE OF CONTENTS
Topic Page
Inventory of Contents/ Additional Equipment 4
About WWVB 5
Quick Set-Up Guide 6
Detailed Set-Up Guide
Battery Installation 7
Program Mode 11
Programming Sequence 11
Function Buttons 12
Manual Time Setting 12
Time Zone Setting 13
Daylight Saving Time (DST) Setting 14
GB P.2 GB
P.3
GB P.4 GB
P.5
INVENTORY OF CONTENTS
1. WT-5120 Alarm Clock
2. TX6U Remote temperature transmitter
3. AC adapter/transformer
4. Instruction manual and warranty card.
ADDITIONAL EQUIPMENT (not included)
1. Two fresh 1.5V AA batteries (optional for projection alarm clock)
2. Two fresh 1.5V AA batteries (for remote temperature sensor)
FEATURES OF PROJECTION ALARM
Operation of these features is in section III
1. Radio-controlled time
2. Projection of time and/or remote temperature
3. LED backlight
4. Display of indoor temperature/humidity or alarm time
5. Indoor temperature and humidity
6. Remote outdoor temperature
7. Time alarm
ABOUT WWVB (Radio Controlled Time)
The NIST (National Institute of Standards and Technology-Time and Frequency Division) WWVB
radio station is located in Ft. Collins, Colorado, and transmits the exact time signal continuously
throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away
through the internal antenna in the projection alarm. However, due to the nature of the Earth’s
Ionosphere, reception is very limited during daylight hours. The projection alarm will search for a
signal every night when reception is best.
The WWVB radio station receives the time data from the NIST Atomic clock in Boulder, Colorado.
A team of atomic physicists is continually measuring every second, of every day, to an accuracy of
ten billionths of a second per day. These physicists have created an international standard, mea-
suring a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum. For more detail,
visit http://www.boulder.nist.gov/timefreq.htm. To listen to the NIST time, call (303)499-7111. This
number will connect you to an automated time, announced at the top of the minute in “Coordinated
Universal Time”, which is also known as Greenwich Mean Time (GMT). This time does not follow
AC adapter receptacle
GB P.6 GB
P.7
GB P.8 GB
P.9
Daylight Saving Time changes. After the top of the minute, a tone will sound for every second. It is
possible that your projection alarm may not be exactly on the second due to the variance in the
quartz. However, the clock will adjust the quartz timing over the course of several days to be very
accurate; under 0.10 seconds per day.
QUICK SET-UP GUIDE
Hint
: Use good quality Alkaline Batteries and avoid rechargeable batteries.
1. Have the projection alarm and remote temperature sensor 3 to 5 apart.
2. Batteries should be out of both units for 10 minutes.
3. Place the batteries into the remote temperature sensor rst then into the projection alarm.
4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.
In this time the display and sensor will start to talk to each other and the display will show both the
indoor temperature/humidity and an outdoor temperature. If the station does not display both
temperatures and indoor humidity after the 15 minutes please retry the set up as stated above.
After both indoor and outdoor temperatures are displayed for 15 minutes you can place your sen-
sor outdoors and set your time.
The remote sensor should be placed in a dry, shaded area. The remote sensor has a range of 80
feet. Any walls that the signal will have to pass through will reduce distance. An outdoor wall or
window will have up to 20 feet of resistance and an interior wall will have up to 10 feet of resistance.
Your distance plus resistance should not exceed 80 ft. in a straight line.
NOTE
: Fog and mist will not harm your remote sensor but direct rain must be avoided.
To complete the set up of your temperature station after the 15 minutes have passed please follow
the steps beginning on page 11.
DETAILED SET-UP GUIDE
II. BATTERY INSTALLATION
A. REMOTE TEMPERATURE TRANSMITTER
1. Remove the battery cover.
2. Observing the correct polarity, install 2 AA batteries. The batteries will fit tightly (to avoid start-
up problems make sure that they do not spring free during installation).
3. Replace the battery cover.
B. PROJECTION ALARM
1. Remove the battery cover.
2. Observe the correct polarity, and install 2 AA batteries.
3. In addition or instead of inserting batteries, the AC adapter can be used. Simply plug the adapter
into the receptacle on the underneath of the alarm clock and then plug in adapter.
4. Replace the battery cover.
5. The projector will activate and remain on if the alarm clock is plugged in. If only batteries are
used, the projector will only be activated when a button is pressed. The projection is a red light,
not harmful under normal usage, although care should be taken to not look directly into the
light.
Notes:
After the batteries have been installed a tone will sound, and the LCD (Liquid Crystal Display)
will activate.


Product specificaties

Merk: La Crosse Technology
Categorie: Wekkerradio
Model: WT-5120U

Heb je hulp nodig?

Als je hulp nodig hebt met La Crosse Technology WT-5120U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Wekkerradio La Crosse Technology

Handleiding Wekkerradio

Nieuwste handleidingen voor Wekkerradio