Kicker KM8 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker KM8 (8 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
KM4 | KM65 | KM8
Manual del Propietario | Español
ALTAVOZ COAX KM
Benutzerhandbuch | Deutsch
KM KOAX-SYSTEM
Manuel d’utilisation | Française
HAUT-PARLEURS COAXIAUX KM
KM
Coaxial Speakers
Owner’s Manual
2
The KICKER KM coaxial speakers are speci cally designed for mounting in free-air applications. The
speakers do not require a sealed enclosure for optimum performance. It is important to isolate the sound
coming off the front of the driver from the sound radiating from the back of the driver. This isolation is
usually accomplished by using the driver in a factory speaker location, or in a location with a semi-isolated
rear chamber.
SPECIFICATIONS
Authorized KICKER Dealer:
Purchase Date:
Speaker Model Number:
LOCATION
The sound produced by the KM coaxials is directional. Find the best location for stereophonic sound. If
necessary, add more KM coaxial speakers to the system to help distribute and balance the sound-stage.
After determining the best mounting locations, carefully check the areas where the mounting hardware will
be placed.
Model: KM4 KM65 KM8
Woofer [in, mm] 4, 100 6-1/2, 165 8, 200
Tweeter [in,mm] 1/2, 13 3/4, 20 1, 25
Rated Impedance ] 2, 4 4 4
Peak Power Handling [ Watts] 150 195 300
Continuous Power Handling [Watts RMS] 50 65 150
Sensitivity [1W, 1m] 89 90 92
Frequency Response [Hz] 60-20k 35-21k 30-21k
Mounting Hole Diameter [in, mm] 3-3/4, 94 5-1/16, 128 6-9/16, 170
Mounting Depth [in, mm] 1-13/16, 46 2-3/8, 59.9 3-5/16, 82.9
Grilles Yes Yes Yes
Tweeter Magnet Material Neodymium Neodymium Neodymium
Tweeter Dome Material PEI (polyether imide) Titanium Titanium
Tweeter Design Balanced Dome Dome Dome
Woofer Cone Material Polypropylene Polypropylene Polypropylene
Woofer Surround Material Santoprene Santoprene Santoprene
KM Coaxial Speakers
Owner’s Manual
IMPORTANT SAFETY WARNING
Prolonged continuous operation of an ampli er, speaker, or subwoofer in a distorted, clipped or over-
powered manner can cause your audio system to overheat, possibly catching fi re and resulting in serious
damage to your components and/or vehicle. Amplifi ers require up to 4 inches (10cm) open ventilation.
Subwoofers should be mounted with at least 1 inch (2.5cm) clearance between the front of the speaker and
any surface.
3
Mount the speaker and
grille right side-up to take
advantage of the coaxial
system’s integrated
moisture draining system.
Loops for mounting with Zip Ties
Locking Terminal Cover
Wire Divider
Possible locations for KM
Coaxial Speaker Mounting
Mounted in the Bow
Mounted
Mid-Ship Stern
Mounted
INSTALLATION
Mounting: Make sure the stainless steel mounting screws and U-type speed clips will not puncture the
fuel cell, wiring, or interfere with any mechanical parts on the underside of the mounting surface. Pre-drill
the mounting screw holes using a 7/64” (2.5mm) bit, and attach the KM coaxial speakers to the boat
by fastening the supplied stainless steel coarse-threaded screws to the boat’s structure. If applicable,
use the enclosed stainless steel U-type speed clips. If the supplied hardware is not applicable to your
installation, some other means of securely attaching the speakers to the boat must be used.
Wiring: Carefully place the speaker wire in a location that is clear of standing water and moving
components of the boat. For reference, the Blue wire is Positive and the Grey wire is Negative. The
locking terminal cover with water resistant gasket is removable for wiring installation; it helps prevent
terminal corrosion and electrical shorting. Connect the gold-plated male quick-disconnect on the end
of the 7 inch (175mm) speaker wire leads coming out of the sealed speaker basket to the wires from
your ampli er or source unit. Place the connected wires into the locking terminal, making sure the divider
separates the blue and silver wire quick disconnects, and snap the locking terminal cover into place.
Connect the other end of the wire to your amplifi er in accordance with its owners manual. Mount the
locking terminal cover in a location free and clear of standing water by utilizing the supplied zip ties
through the integrated loops in the locking terminal cover.


Product specificaties

Merk: Kicker
Categorie: Speaker
Model: KM8

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker KM8 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Kicker

Handleiding Speaker

Nieuwste handleidingen voor Speaker