Kicker CompVT 43CVT122 Handleiding

Kicker Subwoofer CompVT 43CVT122

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker CompVT 43CVT122 (20 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 81 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/20
CVT10 | CVT12
Manual del Propietario | Español
CompVT ALTAVOZ PARA SONIDOS GRAVES
Benutzerhandbuch | Deutsch
CompVT TIEFTÖNER
Manuel d’utilisation | Française
CompVT HAUT-PARLEUR D’EXTRÊMES GRAVES
COMPVT
SUBWOOFERS
Owner’s Manual
™
2016 CompVT Rev C.indd 1
2016 CompVT Rev C.indd 1
2016 CompVT Rev C.indd 1
2016 CompVT Rev C.indd 1
2016 CompVT Rev C.indd 1 4/27/2017 10:11:02 AM
4/27/2017 10:11:02 AM
4/27/2017 10:11:02 AM
4/27/2017 10:11:02 AM
4/27/2017 10:11:02 AM
2
SPECIFICATIONS
CompVT Subwoofer Owner’s Manual
Authorized KICKER Dealer:
Purchase Date:
Speaker Model Number:
Speaker Serial Number:
Model CVT10 CVT12
Rated Impedance [Ω] 2 or 4 2 or 4
Fs [Hz] 32.7 32.7
Continuous Power Handling [Watts RMS] 350 350
Sensitivity [1W, 1m] 87.2 87.1
Qts .440 .518
Qms 9.56 10.16
Qes .461 .546
Re [Ω] 2.13 2.16
Vas [ft³, L] 1.30 [37.14] 2.15 [61]
Xmax (Linear Excursion) [mm] 10.5 10.5
Outer Frame Dimension [in, cm] 10-11/16 [27.1] 12-5/8 [32]
Mounting Depth [in, cm] 4-1/4 [10.8] 4-3/8 [11.1]
Mounting Cutout [in, cm] 9-3/16 [23.3] 11 [28.1]
Frequency Response [Hz] 25–500 25–500
CVT10 | CVT12Models:
Figure 1
Series Wiring Parallel Wiring
WIRING
Two 2Woofers = 4 Load
Two 4Woofers = 8 Load
Two 2Woofers = 1 Load
Two 4Woofers = 2 Load
2016 CompVT Rev C.indd 2
2016 CompVT Rev C.indd 2
2016 CompVT Rev C.indd 2
2016 CompVT Rev C.indd 2
2016 CompVT Rev C.indd 2 4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
3
SEALED ENCLOSURE APPLICATIONS
CompVT woofers perform well in any size sealed enclosure between the minimum and maximum
volume recommendations. These systems will exhibit benefi ts of both designs: Minimum produces
high-impact bass, and maximum generates low bass frequency protraction. Overall, the system will
sound more like the recommended enclosure design it is closest to in enclosure volume. These
enclosure recommendations have been calculated with the airspace inside the enclosure and include the
displacement of the woofer. All sealed-enclosure airspace should be fi lled to 50% loose poly-fi l (polyester
fi berfi ll) stuffi ng. Do not make the airspace greater than the maximum enclosure volume recommendation.
To make the most effi cient use of space when building the Sealed Minimum enclosure for your CompVT
subwoofer, you must use the included clearance plate. The clearance plate allows the CompVT
subwoofer to sit recessed within the back panel of the subwoofer box to minimize the enclosure’s
depth. The clearance plate must seal tightly. First, use a plunging router, straight-cut bit, and a circle jig
to create a 1/16” (2mm) deep recess with an outer diameter of 6 1/2” (16.7cm) and an inner diameter
of approximately 5” (12.7cm). Center the recess behind the subwoofer on the back panel. Then, cut
a 5 1/4” (13.3cm) diameter hole in the center of the recess all the way through the back panel. Using
the clearance plate as a reference, drill the six screw holes with a #29 (0.136”, 3.5mm) drill bit. Next,
countersink each screw hole using a 1/4” (6mm) drill or countersinking bit so the clearance plate will fi t
tightly against the back panel. Remove the paper backing from the foam gasket and adhere it to the inside
of the clearance plate. Then, fasten the clearance plate to the box with six #8 screws. See Figure 3.
Model Volume ft3 [L] Panel A in. [cm] Panel B in. [cm] Panel C in. [cm]
CVT10 .8 [22.7] 18x30.5 [45.7x77.5] 3x30.5 [7.6x77.5] 3x16.5 [7.6x41.9]
CVT12 1 [28.32] 18x36 [45.7x91.4] 3.125x36 [7.9x91.4] 3.125x16.5 [7.9x41.9]
Model Volume ft 3 [L] Power Handling
CVT10 .8 [22.7] 350W RMS
CVT12 1 [28.3] 350W RMS
Model Volume ft 3 [L] Power Handling
CVT10 3 [85] 300W RMS
CVT12 4.6 [130] 300W RMS
Panel Dimensions for Sealed Minimum enclosures using 3/4” (1.9cm) thick MDF (See Figure 2)
Sealed Minimum Sealed Maximum
Figure 2
2016 CompVT Rev C.indd 3
2016 CompVT Rev C.indd 3
2016 CompVT Rev C.indd 3
2016 CompVT Rev C.indd 3
2016 CompVT Rev C.indd 3 4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4
VENTED ENCLOSURE APPLICATIONS
The smaller enclosures are best for use in limited-space applications. The larger recommended
enclosures will yield slightly more bass at the lowest frequencies.
The vented minimum design increases bass effi ciency
and fi ts in many space-limited applications. Although
it is the smallest recommended vented enclosure, the
output from 30Hz–80Hz will be considerably higher than
that of a sealed box. The maximum vented design has
even more output in this frequency band. The maximum
vented enclosure is the largest and most effi cient design.
BOX BUILDING NOTES
Use 3/4” (1.9cm) or thicker MDF (medium density
fi berboard) and seal the joints with silicone. Use the
“template” inside your CompVT’s shipping carton to mark
the mounting hole, then cut directly on the line. These
designs need internal bracing. Add triangular bracing
between each of the larger unsupported panels. See
Figure 4.
D
D
D
Figure 4
D = 3” x 3” for CVT12
D = 2” x 2” for CVT10
Clearance Plate
1/16” (2mm) recess
6 1/2”
(16.7cm)
recess outer
diameter
5 1/4”
(13.3cm)
cut out
diameter
Drill with #29 (0.136”, 3.5mm) bit,
then countersink with 1/4” (6mm)
bit, six holes equally spaced. Use
the clearance plate as a template.
Figure 3
Vented Minimum CompVT10 CompVT12
Box Volume, ft3 [L] 1.25 [35.4] 1.75 [49.6]
Port Opening, in x in [cm x cm] 2x10.5 [5.1x26.7] 2.5x12.5 [6.4x31.8]
Port Length, in [cm] 20 [50.8] 20 [50.8]
Power Handling, RMS 200 300
Vented Maximum CompVT10 CompVT12
Box Volume, ft3 [L] 1.75 [49.6] 2.25 [63.7]
Port Opening, in x in [cm x cm] 2.5x10.5 [6.4x26.7] 3x12.5 [7.6x31.8]
Port Length, in [cm] 20 [50.8] 20.5 [52.1]
Power Handling, RMS 200 300
2016 CompVT Rev C.indd 4
2016 CompVT Rev C.indd 4
2016 CompVT Rev C.indd 4
2016 CompVT Rev C.indd 4
2016 CompVT Rev C.indd 4 4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
4/27/2017 10:11:09 AM
5
All the cubic feet (L) measurements in this manual include the displacement of the woofer. For the vented
enclosures the displacement of the port must be calculated and added to the internal volume of the fi nal
design.
Use the outer dimensions of the port and multiply “X Y Z”, then convert to cubic feet. For example, the x x
CVT12 Vented Minimum design’s external port dimensions are, using 3/4” (1.9cm) MDF:
(12.5” 1.5” total MDF wall thickness) + x
(2.5” 1.5” total MDF wall thickness) + x
(20”) (1 ftx3 / 1728 in3 ) .65 ft=3,
Then, add this number to the internal volume of
the enclosure. 1.75 ft3 + .65 ft3 = 2.4 ft3. See
Figure 5.
Due to the necessary length of these ports, you
may want to fold the port along the bottom and
back walls. It will be impractical to use round
ports for these designs.
Do not install a port opening against a solid
surface, such as an internal brace, back-
panel or trunk wall, seat or interior panel of
your vehicle. The port opening must remain
unobstructed. Use the smallest dimension of
the rectangular port as the minimum amount of
space between the port opening and any solid
surface to insure unrestricted airfl ow.
If you prefer an ultra-smooth bass response, you should loosely fi ll your CompVT enclosure with poly-fi l
stuffi ng. Vented designs will require covering the end of the port (located inside the box) with grill cloth,
chicken wire, or expanded metal to prevent the poly-fi l from exiting the port. The use of poly-fi l will slightly
decrease effi ciency, but will deepen and extend the low frequency output.
For more advice on box building, refer to your Authorized KICKER Dealer, or click on the Support tab on
the KICKER homepage, www.kicker.com. Please e-mail support@kicker.com or call Technical Support
at (405) 624-8583 for specifi c or unanswered questions.
Sound Check: Poor bass response? Check the system phasing by reversing the positive and negative
speaker connections on the subwoofer. If the bass improves, then the subwoofer was out of phase in
reference to the rest of the audio system.
Note: All specifi cations and performance fi gures are subject to change. Please visit www.kicker.com
for the most current information. To get the best performance from your new KICKER Subwoofer, we
recommend using genuine KICKER Accessories and Wiring. Please allow two weeks of break-in time for
the subwoofer to reach optimum performance.
If mounting in trunk space or other compartments of the vehicle, pay attention to cable lines, trunk
springs, hinges and seat mechanisms that could cause problems with the operation of the vehicle or
stereo system. Carefully lay the stereo system cables; pay attention to seat fasteners and other items that
could harm the cables.
WARNING: KICKER products are capable of producing sound levels that can permanently damage your
hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening
to an undistorted system at the same volume level. The threshold of pain is always an indicator that the sound
level is too loud and may permanently damage your hearing. Please use common sense when controlling
volume.
Y
X
Z
Figure 5
2016 CompVT Rev C.indd 5
2016 CompVT Rev C.indd 5
2016 CompVT Rev C.indd 5
2016 CompVT Rev C.indd 5
2016 CompVT Rev C.indd 5 4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
6
CompVT Subwoofer Manual del Propietario
ESPECIFICACIONES
CABLEADO
Distribuidor autorizado de KICKER:
Fecha de compra:
Número de serie del Subwoofer:
Modelo: CVT10 CVT12
Impedancia nominal [Ω] 2 ó 4 2 ó 4
Fs [Hz] 32.7 32.7
Manejo de potencia continua [RMS vatios] 350 350
Sensibilidad [1W, 1m] 87.2 87.1
Qts .440 .518
Qms 9.56 10.16
Qes .461 .546
Re [Ω] 2.13 2.16
Vas [ft³, L] 1.30 [37.14] 2.15 [61]
Xmax (Lineal Excursión) [mm] 10.5 10.5
Dimensión externa de bastidor [pul., cm] 10-11/16 [27.1] 12-5/8 [32]
Recorte de instalación [pul., cm] 4-1/4 [10.8] 4-3/8 [11.1]
Diámetro del hueco de montaje, plg [cm] 9-3/16 [23.3] 11 [28.1]
Respuesta de frecuencia [Hz] 25–500 25–500
CVT10 | CVT12
Modelos:
Cableado en serie Cableado en paralelo
Figura 1
Dos 2 Altavoces = Carga de 4 
Dos 4 Altavoces = Carga de 8 
Dos 2 Altavoces = Carga de 1 
Dos 4 Altavoces = Carga de 2 
2016 CompVT Rev C.indd 6
2016 CompVT Rev C.indd 6
2016 CompVT Rev C.indd 6
2016 CompVT Rev C.indd 6
2016 CompVT Rev C.indd 6 4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
7
APLICACIONES DE CAJA SELLADA
Los woofers CompVT se desempeñan bien en cualquier tamaño de caja sellada entre las
recomendaciones minimo y volumen maximo. Estos sistemas mostrarán benefi cios de ambos diseños:
Minimo produce un grave de alto impacto, y maximo genera una prolongación de frecuencia de los
graves. En general, el sistema sonará más como el diseño de caja recomendada al que esté más
cercano al volumen de su caja. Estas recomendaciones de la caja se han calculado con el espacio
aéreo dentro de la caja, e incluyen el desplazamiento del woofer. Todo el espacio aéreo de la caja sellada
deberá de llenarse al 50% con relleno holgado de poly-fi l (fi bra de relleno de poliéster.
Modelo Volumen, pies3 [L] Panel A, plg [cm] Panel B, plg [cm] Panel C, plg [cm]
CVT10 .8 [22.7] 18X30.5 [45.7X77.5] 3X30.5 [7.6X77.5] 3X16.5 [7.6X41.9]
CVT12 1 [28.3] 18X36 [45.7X91.4] 3.125X36 [7.9X91.4] 3.125X16.5 [7.9X41.9]
Modelo Volumen, pies3 [L] Procesamiento
de potencia
CVT10 .8 [22.7] 350W RMS
CVT12 1 [28.3] 350W RMS
Modelo Volumen, pies3 [L] Procesamiento
de potencia
CVT10 3 [85] 300W RMS
CVT12 4.6 [130] 300W RMS
Dimensiones del panel para las cajas selladas mínimas recomendadas con MDF de 3/4 de plg. (1.9cm):
Sellado Compact Sellado SQ
Figura 2
Para utilizar de la manera más efi ciente el espacio cuando se construya la caja sellada compacta para
el subwoofer CompVT, debe usarse la placa espaciadora incluida. La placa espaciadora permite que
el subwoofer CompVT quede empotrado en el panel trasero de la caja de subwoofer para minimizar
la profundidad de la caja. La placa espaciadora debe quedar fi rmemente sellada. Primero, con una
ranuradora vertical, una broca de corte recto y un posicionador circular, forme un hueco de 1/16 de
plg. (2 mm) de profundidad con un diámetro externo de 6 1/2 plg. (16,7 cm) y un diámetro interno de
aproximadamente 5 plg. (12,7 cm). Centre el hueco detrás del subwoofer en el panel de atrás. Luego,
haga un agujero de 5 1/4 plg. (13,3 cm) de diámetro en el centro del hueco hasta traspasar el panel
trasero. Con la placa espaciadora como referencia, haga seis agujeros con una broca perforadora N°
29 de (0,136 plg., 3,5 mm). A continuación avellane cada agujero de tornillo con una broca de 1/4
plg. (6 mm) o una broca avellanadora para que la placa espaciadora ajuste fi rmemente contra el panel
trasero. Quite el revestimiento de papel de la junta de espuma de goma y adhiérala al interior de la placa
espaciadora. Luego, fi je la placa en la caja con los seis tornillos N° 8. Vea la Figura 3.
2016 CompVT Rev C.indd 7
2016 CompVT Rev C.indd 7
2016 CompVT Rev C.indd 7
2016 CompVT Rev C.indd 7
2016 CompVT Rev C.indd 7 4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM
4/27/2017 10:11:10 AM

Product specificaties

Merk: Kicker
Categorie: Subwoofer
Model: CompVT 43CVT122

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker CompVT 43CVT122 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Subwoofer Kicker

Kicker

Kicker 51MWF124 Handleiding

13 Januari 2025
Kicker

Kicker 51MWF104 Handleiding

13 Januari 2025
Kicker

Kicker 51MWE124 Handleiding

9 Januari 2025
Kicker

Kicker 51MWE104 Handleiding

9 Januari 2025
Kicker

Kicker 50CVX124 Handleiding

12 November 2024
Kicker

Kicker 50CVX154 Handleiding

12 November 2024
Kicker

Kicker 51CWQ102 Handleiding

23 September 2024
Kicker

Kicker 51CWQ122 Handleiding

23 September 2024
Kicker

Kicker 43C84 Handleiding

23 September 2024
Kicker

Kicker 51CWQ124 Handleiding

23 September 2024

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

ETON

ETON USB 6 AR Handleiding

18 Maart 2025
ETON

ETON PW 8 Handleiding

18 Maart 2025
ETON

ETON MW 10 FLAT Handleiding

18 Maart 2025
ETON

ETON Graphit 10-4 Handleiding

18 Maart 2025
ETON

ETON Graphit 8-4 Handleiding

18 Maart 2025
ETON

ETON Graphit 8-2 Handleiding

18 Maart 2025
Morel

Morel Ultimo Powerslim 104D Handleiding

11 Maart 2025
Morel

Morel Ultimo Powerslim 124D Handleiding

11 Maart 2025
Rockustics

Rockustics OneSub Handleiding

9 Maart 2025
Morel

Morel Ultimo Powerslim Handleiding

4 Maart 2025