Kenwood NXR-5800 Handleiding
Kenwood
Radio communicatie
NXR-5800
Lees hieronder de đ handleiding in het Nederlandse voor Kenwood NXR-5800 (16 pagina's) in de categorie Radio communicatie. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/16
1
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking information is for use by your
KENWOOD dealer, an authorized KENWOOD service center, or the
factory.
Carefully unpack the repeater. We recommend that you identify
the items listed in the following table before discarding the
packing material. If any items are missing or have been damaged
during shipment, ïŹ le a claim with the carrier immediately.
Item Part Number Quantity
Front glass B10-2781-XX 1
Dressed screw N08-0563-XX 1
Bracket J29-0725-XX 2
Flat head machine screw N32-4008-XX 4
Handle K01-0421-XX 1
DC cord E30-3427-XX 1
Lead wire with connector (15 pin) E31-3228-XX 1
Fuse (15 A) F52-0042-XX 1
SYNC cable E3A-0177-XX 1
Instruction manual B5A-0714-XX 1
INSTALLATION
To install the handles onto the front panel of the repeater, align
the handles with the holes on the front panel, then secure the
handles using the supplied screws.
Consult your dealer for installing the repeater and antenna.
MICROPHONE
Connect an optional KMC-30, KMC-35, KMC-9C, or KMC-53
KENWOOD microphone to the MICROPHONE jack on the front
panel.
OCXO UNIT (KXK-3): Option
The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator
(OCXO) unit.
NOTICES TO THE USER
â Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
â Illegal operation is punishable by ïŹ ne and/or imprisonment.
â Refer service to qualiïŹ ed technicians only.
â This repeater is intended for use as a ïŹ xed base station with
the antenna located outdoors on the rooftop or on an antenna
tower.
â This repeater is designed for a 13.2 V DC power source.
Never use a 24 V DC or higher source to power the repeater.
â Use only the supplied DC cord.
â Do not remove the ferrite core attached to the DC cord. Doing
so may cause interference with radio communications.
â Do not put anything on top of the repeater. This will obstruct
heat dissipation.
THANK YOU!
We are grateful you purchased this KENWOOD repeater.
PRECAUTIONS
âą Do not expose the unit to rain or moisture; to prevent ïŹ re or
electric shock.
âą Do not open the unit under any circumstances; to avoid risk
of electric shock.
âą Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.
âą Do not place the unit in excessively dusty and/or humid
areas, nor on unstable surfaces.
âą Do not put the plastic bag used for packing of this equipment
on the place which reaches a small child's hand. It will
become a cause of suffocation if it wears ïŹ atly.
âą Always switch the transceiver power off before installing
optional accessories.
âą If you detect an abnormal odor or smoke coming from the
unit, disconnect the power from the unit immediately. Contact
your KENWOOD service center or dealer.
NOTIFICATION
This equipment complies with the essential requirements of Directive
1999/5/EC.
The use of the warning symbol means the equipment is subject to
restrictions of use in certain countries.
This equipment requires a licence and is intended for use in the countries
as below.
AT BE DK FI FR DE GR IS IE
IT LI LU NL NO PT ES SE CH
GB CY CZ EE HU LV LT MT PL
SK SI BG RO HR TR
ISO3166
B5A-0714-00 (E)
VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER
INSTRUCTION MANUAL
NXR-5700/ NXR-5800
â Do not install the repeater in explosive atmospheres
(inïŹ ammable gas, dust particles, metallic powders, grain
powders, etc.).
Hereby, JVCKENWOOD Nederland B.V. declares that the radio
equipment types in this instruction manual are in compliance with
Directive 1999/5/EC. The full text of the EU declaration of conformity
is available at the following internet address:
http://www.kenwood.com/cs/com/ecdoc/
(Note: The detail type designations are described in the EU
declaration of conformity.)
Firmware Copyrights
The title to and ownership of copyrights for ïŹ rmware embedded in
KENWOOD product memories are reserved for JVC KENWOOD
Corporation.
Information on Disposal of Old Electrical and Electronic Equipment and Batteries
(applicable for countries that have adopted separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled bin)
cannot be disposed as household waste.
Old electrical and electronic equipment and batteries should be
recycled at a facility capable of handling these items and their waste
byproducts.
Contact your local authority for details in locating a recycle facility
nearest to you.
Proper recycling and waste disposal will help conserve resources
whilst preventing detrimental effects on our health and the environment.
©
2015
The AMBE+2
TM
voice coding Technology embodied in this product
is protected by intellectual property rights including patent rights,
copyrights and trade secrets of Digital Voice Systems, Inc. This
voice coding Technology is licensed solely for use within this
Communications Equipment. The user of this Technology is
explicitly prohibited from attempting to extract, remove, decompile,
reverse engineer, or disassemble the Object Code, or in any other
way convert the Object Code into a human-readable form. U.S.
Patent Nos. #6,199,037, #6,912,495, #8,200,497, #7,970,606, and
#8,359,197.
2
REPEATER OPERATION
Note: Please consult your dealer for programming the repeater. Due
to the frequency stability on the 6.25 kHz bandwidth channel, when
operating the repeater using an optional OCXO unit, allow the unit to
warm up for 24 hours after turning the power on.
After turning on the power, wait for approximately 10 seconds for
the VCXO or 5 minutes for the OCXO (when mounting) to warm up.
During this time, the CH/STATUS Display will blink. The keys will
function when they are pressed.
When power is applied to the unit, the POWER indicator lights
green. Turn the VOLUME control clockwise until a click sounds, to
unmute the audio. Rotate to adjust the audio. Turn the VOLUME
control counterclockwise fully to mute the audio.
The BUSY indicator lights green while receiving a signal and the
TX indicator lights red while transmitting.
â Rear Panel
a RX IN jack
Connect an RX antenna or a duplexer to this BNC
receptacle.
b TEST/SPKR jack
Test input/output jack. Connect an external speaker to
this jack. When using a Built-in speaker, connect the
attached Lead wire with connector (15 pin) to this jack.
c CONTROL I/O jack
Connect a repeater controller or a remote panel to this
DB-25 interface.
d SYNC 1 / 2 jack
Connect to another repeater to use synchronous frame
signaling for digital trunking.
e LAN jack
Connect to Ethernet. Use a shielded category 5e or higher
standard LAN cable shorter than 3 meters.
CONTROLS AND FUNCTIONS
â Front Panel
f REF OUT jack
Connect to another repeater within the site to supply a
reference signal.
g REF IN jack
Connect from another repeater within the site to receive a
reference signal.
h FUSE
Insert 15 A blade fuse into this fuse holder.
i DC 13.2V jack
Connect a 13.2 V DC power supply to this jack.
j TX OUT jack
Connect a TX antenna or a duplexer to this BNC receptacle.
TRANSCEIVER OPERATION
â Receive
Adjust the volume to your desired level. You may need to
readjust the volume if you are having interference while
receiving a message from your dispatcher or another member
in your ïŹ eet.
The BUSY indicator lights green while a signal is being
received.
â Transmit
1 Listen to the channel before transmitting, to make sure it
is not being used.
2 Press the microphone PTT switch, then speak in your
normal speaking voice.
The TX indicator lights red while transmitting.
3 When you ïŹ nish speaking, release the PTT switch.
a Speaker
b CH/STATUS display
Two 17-segment digits display the channel number, name,
or status.
c STATUS indicator
Indicates the status of the repeater. (NXDN mode)
d Programmable function keys
Press these keys to activate their programmable functions.
e USB jack (B-Type)
Connect to the PC using a USB cable.
f VOLUME control
Turn clockwise until a click sounds, to unmute the audio.
Rotate to adjust the audio. Turn counterclockwise fully to
mute the audio.
g MICROPHONE jack
Connect a microphone to this 8-pin modular jack.
h POWER indicator
Lights green when power is supplied to the DC 13.2V jack.
Blinks red when an abnormal voltage is present. While
blinking, the repeater cannot be used.
i TX indicator
Lights red while transmitting.
j BUSY indicator
Lights green while a signal is being received.
k OCXO indicator
The OCXO indicator shows the state of the reference
10 MHz oscillator :
Lights Green when using a reference signal from an
optional OCXO unit (KXK-3).
Lights Orange when using a reference signal from another
repeater.
Blinks orange when 50 ï termination is set to the repeater
while having reference signal from another repeater.
Lights red when no reference signal is available or when
an error occurs.
Does not light when using an internal VCXO reference
signal.
l CTRL indicator
The CTRL indicator shows the control channel status
while using Digital trunking :
Lights Green when the repeater is used as control
channel.
Blinks Green when using a non-dedicated control channel.
ab defg
hi
c
MICROPHONE
VOLUME
OFF/
POWERCTRL OCXO BUSY TX
12
MON
TAKE
OVER
RPT
DISABLE
ABC
345678
STATUS
jkl
ab defgc
TEST/SPKR
RX TX
CONTROL I/O SYNC
12
LAN
REF OUT REF IN
FUSE
15
DC 13.2V
FUSE 15A
hi j
F-1
MERCI !
Nous sommes trÚs heureux que vous ayez acheté ce répéteur
KENWOOD.
PRECAUTIONS
âą Nâexposez pas lâunitĂ© Ă la pluie ou lâhumiditĂ© pour Ă©viter tout risque
dâincendie ou de choc Ă©lectrique.
âą Nâouvrez lâunitĂ© sous aucun prĂ©texte aïŹ n dâĂ©viter tout risque de choc
Ă©lectrique.
âą Nâexposez pas lâunitĂ© aux rayons directs du soleil pendant des
pĂ©riodes prolongĂ©es, ne le posez pas non plus Ă proximitĂ© dâappareils
de chauffage.
âą Ne posez pas lâunitĂ© dans des endroits extrĂȘmement poussiĂ©reux et/
ou humides, ni sur des surfaces instables.
âą Ne mettez pas le sac plastique utilisĂ© pour lâemballage de cet
Ă©quipement dans un lieu Ă portĂ©e de la main dâun petit enfant. Il
deviendra une cause de suffocation si on le porte complĂštement.
âą Veillez Ă toujours mettre lâĂ©metteur-rĂ©cepteur hors tension avant
dâinstaller des accessoires en option.
⹠Si vous détectez une odeur anormale ou une fumée provenant de
lâunitĂ©, dĂ©branchez lâunitĂ© immĂ©diatement. Contactez votre centre de
service ou revendeur KENWOOD.
REMARQUES DESTINEES A LâUTILISATEUR
â La loi gouvernementale interdit lâutilisation dâĂ©metteurs-rĂ©cepteurs radio
non autorisés sur les territoires sous contrÎle gouvernemental.
â Une utilisation illĂ©gale est punissable dâune amende et/ou dâune peine
dâemprisonnement.
â ConïŹ ez lâentretien uniquement Ă des techniciens qualiïŹ Ă©s.
â Nâinstallez pas le module dans des atmosphĂšres explosives (gaz
inïŹ ammable, particules de poussiĂšres, poudres mĂ©talliques, poudres en
grain, etc.)
ATTENTION
â Ce rĂ©pĂ©teur est conçu pour une utilisation en tant que station de base ïŹ xe
avec lâantenne situĂ©e Ă lâextĂ©rieur sur le toit ou un pylĂŽne dâantenne.
â Ce rĂ©pĂ©teur est conçu pour une source dâalimentation de 13,2 Vcc !
Nâutilisez jamais une source dâalimentation de 24 Vcc ou supĂ©rieure pour
alimenter le répéteur.
â Utilisez uniquement le cĂąble CC fourni.
â Nâenlevez pas le noyau magnĂ©tique ïŹ xĂ© au cĂąble CC. Dans le cas contraire,
cela peut entraßner des interférences avec les communications radio.
â Ne mettez rien sur le rĂ©pĂ©teur. Cela va gĂȘner la dissipation de chaleur.e
mettez rien sur le rĂ©pĂ©teur. Cela va gĂȘner la dissipation de chaleur.
DEBALLAGE ET VERIFICATION DE
LâEQUIPEMENT
Remarque : Les informations suivantes relatives au déballage doivent
ĂȘtre utilisĂ©es par votre revendeur KENWOOD, un centre de service agrĂ©Ă©
KENWOOD ou lâusine.
DĂ©ballez le rĂ©pĂ©teur avec soin. Nous vous recommandons dâidentiïŹ er
les articles Ă©numĂ©rĂ©s dans le tableau suivant avant de jeter lâemballage.
Si un article est manquant ou a été endommagé pendant le transport,
remplissez immédiatement un formulaire de plainte avec le transporteur.
Article Numéro de piÚce Quantité
Glace avant B10-2781-XX 1
Vis parée N08-0563-XX 1
Fixation J29-0725-XX 2
Vis Ă mĂ©taux Ă tĂȘte plate N32-4008-XX 4
Manche et ensemble de vis K01-0421-XX 1
CĂąble CC E30-3427-XX 1
Fil avec connecteur (15 broches) E31-3228-XX 1
Fusible (15 A) F52-0042-XX 1
CĂąble SYNC E3A-0177-XX 1
Mode dâemploi B5A-0714-XX 1
INSTALLATION
Pour installer les poignées sur le panneau avant du répéteur, alignez les
poignĂ©es aux oriïŹ ces sur le panneau avant, ensuite, ïŹ xez les poignĂ©es Ă
lâaide des vis fournies.
Veuillez contacter votre revendeur pour lâinstallation du rĂ©pĂ©teur et de
lâantenne.
MICROPHONE
Connectez un microphone KMC-30, KMC-35, KMC-9C ou KMC-53C
KENWOOD en option Ă la prise MICROPHONE du panneau avant.
UNITE OCXO (KXK-3) : Option
LâunitĂ© OCXO (KXK-3) est un Oscillateur Ă quartz thermostatĂ© (OCXO).
BASE-RELAIS NUMĂRIQUE VHF/ BASE-RELAIS NUMĂRIQUE UHF
MODE DâEMPLOI
NXR-5700/ NXR-5800
Information sur lâĂ©limination des anciens Ă©quipements Ă©lectriques et
Ă©lectroniques et piles Ă©lectriques (applicable dans les pays de qui ont
adopté des systÚmes de collecte sélective)
Les produits et piles Ă©lectriques sur lesquels le pictogramme
(poubelle barrée) est apposé ne
peuvent pas ĂȘtre Ă©liminĂ©s comme ordures mĂ©nagĂšres.
Les anciens Ă©quipements et batteries Ă©lectriques et Ă©lectroniques
doivent ĂȘtre recyclĂ©s sur des sites en mesure de traiter ces
produits et leurs déchets.
Contactez vos autorités locales pour connaßtre le site de recyclage
le plus proche.
Un recyclage adaptĂ© et lâĂ©limination des dĂ©chets aideront Ă
conserver les ressources et Ă nous
préserver des leurs effets nocifs sur notre santé et sur
lâenvironnement.
La technologie de codage AMBE+2
TM
incorporée à ce produit est
protégée par des droits de propriété intellectuelle, y compris les
droits de brevet, droits dâauteur et les secrets commerciaux de
Digital Voice Systems, Inc. Cette technologie de codage de voix est
sous licence uniquement pour ĂȘtre utilisĂ©e avec cet Ă©quipement
de communication. Il est interdit explicitement a lâutilisateur de
cette technologie de tenter dâextraire, de prĂ©lever, de dĂ©compiler,
de désosser ou de désassembler le code objet, ou de convertir de
toute autre façon le code objet en une forme lisible par lâhomme. No.
de brevet pour les Ătats-Unis #6,199,037, #6,912,495, #8,200,497,
#7,970,606, et #8,359,197.
NOTIFICATION
Cet Ă©quipement est conforme aux principales exigences de la Directive 1999/5/CE.
Lâusage du symbole dâavertissement signifie que lâĂ©quipement est soumis Ă
des restrictions dâusage dans certains pays.
Cet Ă©quipement nĂ©cessite un contrat de licence et il est destinĂ© Ă ĂȘtre utilisĂ© dans
les pays ci-dessous.
AT BE DK FI FR DE GR IS IE
IT LI LU NL NO PT ES SE CH
GB CY CZ EE HU LV LT MT PL
SK SI BG RO HR TR
ISO3166
Droits dâauteur du micrologiciel
Le titre et la propriĂ©tĂ© des droits dâauteur pour le micrologiciel intĂ©grĂ© dans la
mémoire du produit KENWOOD sont réservés pour JVC KENWOOD Corporation.
AVERTISSEMENT
Product specificaties
| Merk: | Kenwood |
| Categorie: | Radio communicatie |
| Model: | NXR-5800 |
Heb je hulp nodig?
Als je hulp nodig hebt met Kenwood NXR-5800 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Radio communicatie Kenwood
16 April 2022
23 April 2022
2 Mei 2022
2 Mei 2022
30 April 2022
23 April 2022
15 Augustus 2022
7 Mei 2022
16 Augustus 2022
3 Mei 2022
Handleiding Radio communicatie
- Radio communicatie Motorola
- Radio communicatie Albrecht
- Radio communicatie Baofeng
- Radio communicatie Furuno
- Radio communicatie GTV
- Radio communicatie Icom
- Radio communicatie Intek
- Radio communicatie Multi Care Systems
- Radio communicatie President
- Radio communicatie Rexon
- Radio communicatie Simrad
- Radio communicatie Spektrum
- Radio communicatie Stabo
- Radio communicatie Swissphone
- Radio communicatie Team
- Radio communicatie Vertex Standard
- Radio communicatie Wintec
- Radio communicatie Wouxun
Nieuwste handleidingen voor Radio communicatie
3 September 2023
3 September 2023
2 September 2023
26 Augustus 2023
26 Augustus 2023
31 Januari 2023
31 Januari 2023
14 Juli 2023
31 Januari 2023
13 Mei 2023