Karcher WD 5 P V-25/5/22 Handleiding

Karcher Stofzuiger WD 5 P V-25/5/22

Lees hieronder de 📖 handleiding in het Nederlandse voor Karcher WD 5 P V-25/5/22 (12 pagina's) in de categorie Stofzuiger. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

®, LLC

A Division of Snow Joe

®, LLC

OPERATOR’S MANUAL

Model AJP100E Form No. SJ-AJP100E-880E-M

RRANDOM ORBIT BUFFER + POLISHER

ELECTRIC | 0.7 AMP | 6" | 3800 OPM

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Always follow these safety guidelines. Failure to do so may

result in serious bodily injury or death.

General Power Tool Safety

Warnings

m WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and instructions

may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

mDANGER! This indicates a hazardous situation, which,

if not followed, will result in serious injury or death.

mWARNING! This indicates a hazardous situation, which,

if not followed, could result in serious injury or death.

mCAUTION! This indicates a hazardous situation, which,

if not followed, could result in minor or moderate injury.

Work Area Safety

1. Keep work area clean and well lit – Cluttered or dark

areas invite accidents.

2. Do not operate power tools in explosive atmospheres,

such as in the presence of ammable liquids, gases

or dust – Power tools create sparks which may ignite the

dust or fumes.

3. Keep children and bystanders away while operating a

power tool – Distractions can cause you to lose control.

Electrical Safety

1. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodied plugs and

matching outlets will reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators – There is an increased risk of electric shock

if your body is earthed or grounded.

3. Do not expose power tools to rain or wet conditions

– Water entering a power tool will increase the risk of

electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

6. If operating a power tool in a damp location is

unavoidable, use a Ground Fault Circuit Interrupter

(GFCI) protected supply. Use of a GFCI reduces the risk

of electric shock.

Personal Safety

1. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the inuence

of drugs, alcohol or medication – A moment of

inattention while operating power tools may result in

serious personal injury.

2. Use safety equipment. Always wear eye protection

– Safety equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

3. Prevent unintentional starting. Ensure the switch is in

the o-position before connecting to power source,

picking up or carrying the tool. – Carrying power tools

with your nger on the switch or energizing power tools

that have the switch on invites accidents.

4. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

5. Do not overreach. Keep proper footing and balance at

all times – This enables better control of the power tool in

unexpected situations.

6. Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts – Loose clothes, jewelry or long hair can be caught

in moving parts.

7. Only use safety equipment that has been approved

by an appropriate standards agency – Unapproved

safety equipment may not provide adequate protection.

Eye protection must be ANSI-approved and breathing

protection must be NIOSH-approved for the specic

hazards in the work area.

8. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

9. Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe

injury within a fraction of a second.

Power Tool Use + Care

1. Do not force the power tool. Use the correct power

tool for your application – The correct power tool will

do the job better and safer at the rate for which it was

designed.

2. Do not use the power tool if the switch does not turn

it on and o – Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source from the

power tool before making any adjustments, changing

accessories, or storing power tools – Such preventive

safety measures reduce the risk of starting the power tool

accidentally.

4. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool – Power

tools are dangerous in the hands of untrained users.

5. Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage of

parts and any other condition that may aect the power

tool’s operation. If damaged, have the power tool repaired

before use Many accidents are caused by poorly –

maintained power tools.

6. Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

7. Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. – Use of the power tool for operations

dierent from those intended could result in a hazardous

situation.

8. Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

Service

Have your power tool serviced by a qualied repair person

using only identical replacement parts. This will ensure that

the safety of the power tool is maintained.

Electrical Safety

1. Ground fault circuit interrupter (GFCI) protection should

be provided on the circuit(s) or outlet(s) to be used for

this electric Buer + Polisher. Receptacles are available

having built-in GFCI protection and may be used for this

measure of safety.

2. Make sure that the mains voltage matches that listed on

the unit's rating label. Using the improper voltage can

damage the Buer + Polisher and injure the user.

3. To prevent electric shock, use only with an extension

cord suitable for indoor use only, such as SW-A, SOW-A,

STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A, or

SJTOW-A.

Before use, check that the extension cord is in good

condition. When using an extension cord, make sure to

use one heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating.

4. To prevent the appliance cord from disconnecting from the

extension cord during operation, make a knot with the two

cords as shown in Table 1.

m WARNING m

Electric shock may cause SEVERE INJURY or

DEATH. Heed these warnings:

• Do not allow any part of the electric Buer + Polisher

to make contact with water while it is in operation.

If the appliance becomes wet while turned o, wipe

dry before starting.

• Do not use an extension cord over 10 ft. The Buer +

Polisher comes equipped with a 11.8 in. power cable.

Combined cord length must not exceed 11 ft.

Any extension cord must be 18-gauge (or heavier) to

safely power the Buer + Polisher.

• Do not touch the appliance or its plug with wet hands

or while standing in water. Wearing rubber boots

oers some protection.

EXTENSION CORD CHART

Cord Length:

Min. Wire Gauge (A.W.G.):

10 ft (3 m)

5. Do not abuse the cord. Never pull the Buer + Polisher

by the cord or yank the cord to disconnect it from the

receptacle. Keep the cord away from heat, oil and sharp

edges.

6. To reduce the risk of electric shock, this appliance has a

polarized plug (i.e. one blade is wider than the other). Use

this appliance only with a polarized UL-, CSA- or ETL listed

extension cord. The appliance plug will t into a polarized

extension cord only one way. If the appliance plug does not

t fully into the extension cord, reverse the plug. If the plug

still does not t, obtain a correct polarized extension cord. A

polarized extension cord will require the use of a polarized

wall outlet. The extension cord plug will t into the polarized

wall outlet only one way. If the plug does not t fully into

the wall outlet, reverse the plug. If the plug still does not

t, contact a qualied electrician to install the proper wall

outlet. Do not modify the appliance plug, extension cord

receptacle or extension cord plug in any way.

7. Double insulation – In a double-insulated appliance, two

systems of insulation are provided instead of grounding.

No grounding means is provided on a double-insulated

appliance, nor should a means for grounding be added

to the appliance. Servicing a double-insulated appliance

requires extreme care and knowledge of the system,

and should be performed only by qualied service

personnel at an authorized Snow Joe

+ Sun Joe

dealer.

Replacement parts for a double-insulated appliance must

be identical to the parts they replace. A double-insulated

appliance is marked with the words “Double Insulation”

or “Double Insulated.” The symbol (square within a

square) may also be marked on the appliance.

8. If the replacement of the supply cord is necessary, this has

to be done by the manufacturer or his agent in order to

avoid a safety hazard.

Safety Warnings Common for

Polishing Operations

The manufacturer will not be held responsible for injuries

resulting from incorrect use of the device or from use that does

not comply with the directions.

1. This power tool is intended to function as a polisher.

Read all safety warnings, instructions, illustrations and

specications provided with this power tool. Failure to follow

all instructions listed below may result in electric shock, re

and/or serious injury.

2. Operations such as grinding, sanding, wire brushing,

or cutting-o are not recommended to be performed

with this power tool. Operations for which the power tool

was not designed may create a hazard and cause personal

injury.

3. Do not use accessories which are not specically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power

tool, it does not assure safe operation.

4. The rated speed of the accessory must be at least

equal to the maximum speed marked on the power tool.

Accessories running faster than their RATED SPEED can

break and y apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

6. The arbor size of wheels, anges, backing pads or any

other accessory must properly t the spindle of the

power tool. Accessories with arbor holes that do not match

the mounting hardware of the power tool will run out of

balance, vibrate excessively and may cause loss of control.

7. Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess wear,

wire brush for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or install an

undamaged accessory. After inspecting and installing an

accessory, position yourself and bystanders away from

the plane of the rotating accessory and run the power tool

at maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test time.

8. Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of stopping

small abrasive or workpiece fragments.

The eye protection must be capable of stopping ying

debris generated by various operations. The dust mask

or respirator must be capable of ltering out particles

generated by your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

9. Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may y away and cause injury beyond

immediate area of operation.

10. Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning accessory.

(B) Connect plug and receptacle

Cord set Appliance cord

(A) Tie cord as shown

Table 1. Method of Securing Extension Cord

Product specificaties

Merk:	Karcher
Categorie:	Stofzuiger
Model:	WD 5 P V-25/5/22
Soort bediening:	Draaiknop
Kleur van het product:	Black, Stainless steel, Yellow
Gewicht:	8400 g
Breedte:	382 mm
Diepte:	418 mm
Hoogte:	653 mm
Snoerlengte:	5 m
Gewicht verpakking:	11600 g
Stroombron:	AC
Soort reiniging:	Droog en nat
Aantal wielen:	5 wiel(en)
Draaghandvat:	Ja
Stof blazer:	Ja
Spleetzuigmond:	Ja
Input vermogen:	1100 W
Aanpasbare snelheid:	Ja
Inhoud:	25 l
Slang diameter:	35 mm
Lengte van slang:	2.2 m
AC-ingangsspanning:	220-240 V
AC-ingangsfrequentie:	50/60 Hz
Materiaal container:	Kunststof
Filter materiaal:	Fleece
Activering elektrisch gereedschap:	Ja
Automatische aan/uit-schakelaar:	Ja
Zuigmond vloer nat/droog:	Ja