JVC RV-NB70S Handleiding

JVC Speaker RV-NB70S

Lees hieronder de 📖 handleiding in het Nederlandse voor JVC RV-NB70S (12 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Inserting batteries

Main unit

PREPARATION

NOTE

• The power will not be supplied through the batteries when the power is

supplied through the AC outlet on the unit.

• The battery is consumed more quickly than usual when operating the

unit continuously or operating it in a cold place.

• When the power is supplied using the batteries, the display will be blank

when the unit is turned off (at standby).

• When the power is supplied using the batteries, the unit is turned on by

pressing or source buttons on the main unit.

CAUTION

To avoid battery leakage or explosion, handle batteries properly.

• If you are not going to use this unit for a month or more, remove the

batteries from the battery compartment.

• Dispose of batteries in the proper manner, according to federal, state,

and local regulations.

• Do not mix with batteries of different types or with new and old ones.

• Do not attempt to charge any batteries other than rechargeable ones.

• Discard leaky batteries immediately. Battery leakage can cause skin

burns or other personal injuries.

• If chemicals leak onto the unit, clean the unit completely.

Match the polarities (+ and –) of the batteries.

Remote control

• If the range or effectiveness of the remote control decreases, replace the

batteries.

Connecting the power cord

Battery compartment

Discs CDs with one of the marks below on

the surface.

Files Files in audio CD format, MP3/WMA

files on a finalized CD-R or CD-RW.

MP3/WMA files in a USB device can also

be played.

Playable discs/files

• MP3/WMA discs require a longer readout time

than regular CDs. (It depends on the complexity

of the folder/file configuration.)

• Some MP3/WMA files cannot be played back and

will be skipped. This results from their recording

processes and conditions.

• When making MP3/WMA discs, use ISO 9660

Level 1 for the disc format.

• This unit can play back MP3/WMA files with the

extension code <.mp3> or <.wma> (regardless of

the letter case–upper/lower).

• This system can play back MP3/WMA recorded at

the following sampling frequency and bitrate.

Bitrate: MP3

WMA

32 – 320 kbps

48 – 192 kbps

Sampling frequency: 32 / 44.1 / 48 kHz

• This unit cannot play “packet write” discs.

• This unit cannot show the Tag data of MP3/WMA.

• If a CD-RW has been recorded in a different

format, erase all data on the CD-RW completely

before recording on it.

For connecting/disconnecting:

• USB Memory and DAPs compatible with the USB

mass storage class specifications are connectable.

• Always set the volume to the minimum level when

connecting or disconnecting a USB device.

• When connecting with a USB cable, use the USB 2.0

cable less than 1 m (3.28 ft) in length.

• You cannot connect a computer to the USB

MEMORY terminal of the unit.

• Do not use a USB hub.

• When the power is supplied through the AC outlet

and USB is selected as the source, the USB device

is charged through the USB MEMORY terminal,

however some USB devices may not be charged.

• Deactivate the security function of the USB mass

storage class device before connecting.

For playing back:

• When connecting a USB device, refer also to its

manual.

• You can play back MP3/WMA files on a USB device

(maximum data transfer rate: 2 Mbps). This unit may

not play back some files even though their formats

are listed above.

• The playing order of MP3/WMA files

– in groups depends on in creation order. In a

group, tracks are played in recording order.

– may differ depending on the recording

condition.

– may change if you change the folder name or

file name.

• While playing back a file in a USB device, do

not disconnect the USB device. It may cause

malfunction of both this unit and the device.

• This unit is compatible with USB 2.0 Full Speed.

• You cannot play back a file larger than 2 Gigabytes.

• It is recommended to use the USB mass storage

class device of 4 Gigabytes or less storage

capacity.

• When playing a file of a large transfer rate, sounds

may be dropped during playback.

• This unit cannot recognize a USB mass storage

class device whose rating exceeds 5V/500 mA.

• If your USB device is partitioned, only the first

partition is recognized.

• You cannot send any data to your USB device from

this unit.

• Some USB devices may not be recognized or may

not work properly.

• Some DAPs are not compatible with the unit.

• Copyrighted tracks (WMA-DRM tracks) cannot be

played back on the unit.

• Coded or encrypted tracks in a special method

cannot be played on the unit.

• Electrostatic shock at connecting a USB device

may cause abnormal playback of the device. In

this case, disconnect the USB device then reset

this unit and the USB device.

• JVC bears no responsibility for any loss of data in

the USB mass storage class device while using this

unit.

• Compatible iPod:

Made for Audio Video

iPod nano (6th generation) *

iPod nano (5th generation)

iPod nano (4th generation)

iPod nano (3rd generation)

iPod nano (2nd generation) –

iPod nano –

iPod touch (4th generation)

iPod touch (3rd generation)

iPod touch (2nd generation)

iPod touch

iPod classic

iPod video (5th generation)

iPod photo (4th generation) * *

iPod (4th generation) –

iPod mini (2nd generation) –

iPod mini –

iPhone 4

iPhone 3GS

iPhone 3G

* Only for still picture

* Viewable only on the screen of iPod

• Sound distortion may occur when playing back

audio sources with high recording levels. When

distortion occurs, it is recommended to turn

off the equalizer of iPod. For information on

operating iPod, see the iPod instruction manual.

If iPod does not play correctly, update iPod

software to the latest version.

•

Important for USB mass storage class

device

NOTE

• The power can also be supplied through the batteries (see the instruction

below).

• A small amount of power is always consumed even while on standby.

CAUTION

• Only use JVC power cord provided for this unit to avoid malfunction or

damage to the unit.

• Remove all the batteries when using the power cord.

• Be sure to unplug the power cord from the outlet when going out or when

the unit is not in use for an extended period of time.

Unplug the AC power cord from the unit to supply the power through the

batteries in the battery compartment; otherwise, the unit does not work.

Maintenance

Troubleshooting

Display

Important for iPod devices Disc player

CD capacity: 1CD

Signal-to-noise ratio: 85 dB

Dynamic range: 90 dB

Tuner

FM tuning range: 87.50 MHz –

108.00 MHz

Antenna: FM telescopic

antenna

General

Speakers:

• Full range:

• Super woofer:

8 cm (3 3/16”) cone

x 2

Speaker impedance:

16 Ω

13 cm (5 1/8”) cone

x 2

Speaker impedance:

7 Ω

Output power: 40 W

Input terminal:

• USB MEMORY:

• Dock for iPod:

• AUDIO IN:

Input Sensitivity /

Impedance (1 kHz)

• MIC/GUITAR:

• DC IN:

Playable files:

MP3, WMA

• Compatible device:

Mass storage class

• Compatible system:

FAT16, FAT32

• Output power:

DC 5 V 500 mA

DC 5 V 1 A

φ3.5

• LEVEL 1: 500 mV /

47 kΩ

• LEVEL 2: 250 mV /

47 kΩ

• LEVEL 3: 125 mV /

47 kΩ

Switchable

• MIC: 200 Ω Ω - 2 k

( 6.3)φ

• GUITAR: 100 k - 1 Ω

M ( 6.3)Ω φ

DC 12 V, 2 A

SPECIFICATIONS

Output terminal:

• PHONES

• VIDEO OUT

(For iPod):

φ3.5

32 - 1 kΩ Ω

15 mW / ch output into

32 Ω

Composite

Power supply:

• AC

• DC

For North American

model

AC 120 V , 60 Hz

For European model

AC 230 V , 50 Hz

For Australian model

AC 240 V , 50 Hz

DC 15 V (R20 (SUM-1)/D

(13D)-size batteries x 10)

External DC 12 V

Power

consumption: When using an AC outlet

28 W (at operation)

Less than 1.00 W (on

standby)

When using DC IN

2 A (power on mode)

Dimensions: 666 mm (26 1/4”) x 231

mm (9 1/8”) x 240 mm (9

1/2”) (W/H/D)

Mass: Approx. 6.8 k (15.0 lbs)g

(without batteries

stored in the battery

compartment)

Accessories

provided: Power cord x 1

Remote control x 1

Shoulder belt x 1

Buckle x 2

Stopper x 2

Batteries* (for the remote

control) x 2

* Not provided for North American model.

Design and speci cations are subject to

change without notice.

MP3/WMA groups and tracks are not played

back as you expect.

\ Playing order is determined when the groups

and tracks were recorded. It depends on the

writing application.

The disc/USB device sound is discontinuous.

\ The disc is scratched or dirty.

\ MP3/WMA files have not been properly copied

onto the USB device.

Sounds from USB device are interrupted.

\ Noise and static electricity may stop the sound.

In this case, disconnect and connect the USB

device again after turning off the unit.

iPod Operations

iPod does not play, but “CONNECT” appears on

the display.

\ The iPod battery is low or exhausted. Charge the

iPod battery.

Radio Operations

Hard to listen to broadcasts because of noise.

\ The FM antenna is not properly extended and

positioned.

\ Electrostatic discharge from your body may

cause noise. If this happens, turn off and on the

unit again.

Timer Operations

Daily Timer does not work.

\ The unit has been turned on when the on-time

comes. Timer starts working only when the unit

is turned off.

If you are having a problem with your unit, check this

list for a possible solution before calling for service.

General

Power does not come on.

\ No power is supplied. Check the power cord

connection or change the batteries.

The unit turns off automatically.

\ Auto power save function works.

Adjustments or settings are suddenly canceled

before you finish.

\ There is a time limit. Repeat the procedure again.

Unable to operate the unit or the unit does not

work properly.

\ The built-in microprocessor may malfunction due

to external electrical interference.

Unplug the power cord, then plug it back in.

\ Batteries are exhausted. Change the batteries.

Unable to operate the unit from the remote

control.

\ The path between the remote control and the

remote sensor on the unit is blocked.

\ The batteries are exhausted.

No sound is heard.

\ Headphones are connected.

While the power is supplied using the batteries,

sound from the speakers is distorted or too quiet.

\ Batteries are exhausted. Change the batteries.

Disc/USB Mass Storage Class Device

Operations

The disc/USB device does not play.

\ The disc is placed upside down. Place the disc with

the label side up.

\ The disc is recorded with the “packet writing (UDF

file unit).” It cannot be played. Check the files you

want to play back.

\ The USB device is not connected properly.

To get the best performance of the unit, keep

your discs and mechanism clean.

Handling discs

• Remove the disc from its case by holding it

at the edge while pressing the center hole

lightly.

• Do not touch the shiny surface of the disc, or

bend the disc.

• Put the disc back in its case after use.

• Be careful not to scratch the surface of the

disc when placing it back in its case.

• Avoid exposure to direct sunlight,

temperature extremes, and moisture.

Cleaning discs

• Wipe the disc with a soft cloth in a straight

line from center to edge.

Cleaning the unit

• Stains should be wiped off with a soft cloth. If

the unit is heavily stained, wipe it with a cloth

soaked in water-diluted neutral detergent

and wrung well, then wipe clean with a dry

cloth.

• Since the unit may deteriorate in quality,

become damaged or get its paint peeled off,

be careful about the following:

– DO NOT wipe it hard.

– DO NOT wipe it with thinner or benzine.

– DO NOT apply any volatile substance such

as insecticides to it.

– DO NOT allow any rubber or plastic to

remain in contact for a long time.

Cleaning the CD pickup lens

• Keep the CD pickup lens clean, or the sound

may be degraded. Use a blower (available at a

camera store, etc.) to blow dust off the lens.

ABOUT DISC/FILE/iPod/DISPLAY

“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to

connect specifically to iPod or iPhone, respectively, and has been certified by the developer to

meet Apple performance standards. Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards. Please note that the use of this accessory with

iPod or iPhone may affect wireless performance.

iPhone, iPod, iPod classic, iPod nano and iPod touch are trademarks of Apple Inc., registered in the

U.S. and other countries.

•

Be sure to hold both handles when you carry the unit.

If you carry the unit by only one handle, because of the length of the unit, the other end may

drag on the ground and be damaged as a result.

Do not insert any foreign objects into them which are below the speakers.

NOTE

• Remove a disc, USB device or iPod from the unit.

• Disconnect all the cords from the unit.

• The unit is not waterproof or dust proof.

Using the shoulder belt

Attach the supplied shoulder belt (adjustable in length) to each end of the unit as illustrated.

CARRYING THIS UNIT

Using the carrying handles

1 Timer indicators

• (timer), ON

2 SLEEP indicator

3 CLOCK indicator

4 iPod indicator

5 FM mode indicators

STEREO, MONO

6 Repeat indicators

, ALL,

GROUP

7 Main display

8 PRGM (program)

indicator

9 RANDOM indicator

0 Frequency unit

indicators

For customer use:

Enter below the Model No. and Serial No. which

are located either on the rear, bottom or side of

the cabinet. Retain this information for future

reference.

Model No.

Serial No.

If no operation is performed for 30 minutes

in the following situations, the unit turns off

automatically.

CD or USB is selected, and playback is stopped.

iPod is selected, and iPod is not connected.

The volume level is set to MIN or Muting is

activated.

Before the unit turns off, “APS” blinks on the

•

display.

However, this function does not work in the

following situations:

AUDIO IN or FM is selected.

A microphone or guitar is connected.

•

Microsoft and Windows Media are either

registered trademarks or trademarks of

Microsoft Corporation in the United States and/

or other countries.

•

• This unit can recognize up to a total of 511 tracks

and folders on a disc, and 65536 files in up to 200

groups (maximum 500 files in a single group) on a

USB device.

• The reflection factor of CD-RW is lower than that of

other CDs, possibly causing CD-RW to take longer

time to read.

Auto power save function

Front view/Face

Side view/Côté

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent

damage, locate the apparatus as follows:

1 Front:

No obstructions and open spacing.

2 Sides/ Top/ Back:

No obstructions should be placed in the areas shown

by the dimensions below.

3 Bottom:

Place on the level surface. Maintain an adequate

air path for ventilation by placing on a stand with a

height of 10 cm (3 15/16”) or more.

Attention: Aération correcte

Pour prévenir tout risque de décharge électrique

ou d’incendie et éviter toute détérioration, installez

l’appareil de la manière suivante:

1 Avant:

Bien dégagé de tout objet.

2 Côtés/dessus/dessous:

Assurez-vous que rien ne bloque les espaces

indiqués sur le schéma ci-dessous.

3 Dessous:

Posez l’appareil sur une surface plane et horizontale.

Veillez à ce que sa ventilation correcte puisse se

faire en le plaçant sur un support d’au moins dix

centimètres de hauteur.

Thank you for purchasing a JVC product.

Before operation, please read the instructions

carefully.

15 cm

(5 15/16”)

10 cm

(3 15/16”)

15 cm

(5 15/16”)

15 cm

(5 15/16”)

15 cm

(5 15/16”)

15 cm

(5 15/16”)

10 cm

(3 15/16”)

REFERENCES

Blower

Lens

Battery compartment R20 (SUM-1)/D(13D)

(not supplied)

Power cord

(supplied)

AC outlet

R6(SUM-3)/AA(15F)

(Not supplied for North American model.)

07 86

3 4

521

POWERED WOOFER

CD SYSTEM

RV-NB70B/RV-NB70S

INSTRUCTIONS

LVT2225-001A[J/E/A]

1210TMMMDWBET

Carrying handle

Stopper*

Shoulder belt*

Buckle*

Main unit

Shoulder belt*

Buckle*

Main unit

* Supplied for this unit.

In this manual, “iPod” means iPod, iPod

touch and iPhone device. When iPod touch

or iPhone device is especially refered to,

“iPod touch” or “iPhone” is used.

In this manual, “file“ and “track“ are used

interchangeably.

•

Load a disc or connect a USB device.

Listening to an external device

Before listening to an external device, connect

it properly to the unit.

Refer also to the instruction manual for an

external device.

1. Set the volume level of the unit to

minimum.

2. Connect an external device to the

AUDIO IN jack on the rear of the unit.

1. Press CD 6 6 or USB .

Starts reading the disc or USB device and

playback.

2. Adjust the volume.

To stop playback, Press .7

To pause, press CD or USB 6 6.

• To cancel pause, press again. 6

Playback continues from the point

where it was paused.

To select a track, press or .4 ¢

• Press ¢ once to skip to the

beginning of the next track.

• Press 4 to skip to the beginning of

the track being played.

Press 4 twice quickly to skip to the

beginning of the previous track.

To locate a track directly, press number

buttons.

To fast forward/reverse, press and hold

4 ¢ or during playback.

To select a group (for MP3/WMA), press

GROUP UP or GROUP DOWN. (Remote

control only)

• Press GROUP UP to skip to the next

group.

• Press GROUP DOWN to skip to the

previous group.

To detach the dock adaptor

Pull up the dock adaptor with your fingernail

or sharp pointed tool inserted to the slot.

• Be careful not to injure your fingertips or

damage the terminal of the dock.

Viewing video/picture

While the unit is turned off, and iPod is not

connected...

Press and hold iPod 6.

A Listening to iPod and viewing video/picture from iPod B Playing back a disc/USB

device

C Listening to

FM stations

Using the timer (Remote control only)

D Adjusting the sound

Convenient playback (Remote control only)

1. Press FM to select “FM.”

2. Select the station.

• Press and hold or to change the 4 ¢

frequency automatically until a station of

sufficient signal strength is tuned in.

Presetting stations (Remote control only)

You can preset 30 FM stations manually.

1. Tune in to a station you want to preset.

2. Press SET.

• Finish the following steps while the

indication on the display is flashing.

3. Press the number button to select a

preset number you want to store.

4. Press SET to store the station.

To listen to the preset stations, press number

buttons to select the preset number.

Tuning in to a preset station

Each time you press the button, you can select

the preset station from 1 to 30.

You can select the preset station directly

pressing number buttons.

•

You can operate iPod through the unit.

• Before connecting iPod to the unit, check its type

and software version. (See playable iPod devices

on the other side of this sheet.)

• Note that any data cannot be sent to iPod from

the unit.

CAUTIONS

• JVC is not responsible for any loss of or damage

to iPod that might result from the use of this

product.

• When you connect iPod to the unit, make sure

the connection on this unit is fully inserted into

iPod.

• Do not carry the unit with iPod connected. You

might drop it down or it might cause damages to

the connector part.

• Do not touch or hit the iPod terminal pins or the

connector pins directly. It might cause damages

to the connector part.

• Remove iPod from the unit when you do not use.

• While playing back a track from iPod, do not

disconnect the iPod. Doing so may cause

malfunction of both this unit and iPod.

• Always set the volume to the minimum level

when connecting or disconnecting iPod.

• Do not leave the front door open.

• Do not press down on the front door when it is

open, as the unit could fall and possibly cause

an injury.

1. Press iPod 6.

iPod is turned on and starts playing.

• When you have selected another source

press iPod again to start playback.6

2. Adjust the volume.

To pause, press iPod .6

• To cancel pause, press iPod again. 6

Playback continues from the point

where it has been paused.

To select a track, press or .4 ¢

• Press ¢ once to skip to the beginning of

the next track.

• Press 4 to skip to the beginning of the

track being played.

Press twice quickly to skip to the 4

beginning of the previous track.

To fast forward/reverse, press and hold

4 ¢ or during playback.

NOTE

With iPod selected as the source...

– “CONNECT” appears on the display of the unit

when iPod is connected.

– “NOiPod” appears on the display of the unit

when iPod is not connected.

– Operate iPod touch or iPhone itself in the

following cases:

• When operating the home button.

• When selecting application icons on the

home screen.

• When dragging the slider.

iPod menu operation

(Remote control only)

1 Press MENU to display the menu.

2 Press GROUP UP or GROUP DOWN to

select a menu item, then press SET to

confirm it.

When the power is supplied through the AC outlet

for the first time after the purchase, the CLOCK

indicator and “0:00” (or “AM 12:00”) flash on the

display. Set the clock before using the sleep and

daily timers.

1. Press CLOCK/TIMER.

2. Press 4 1 ¡ ¢/ or / to adjust the hour.

• When you press and hold the button, the

hour digit changes continuously.

3. Press SET.

The minutes digits start flashing on the display.

4. Repeat 2 and 3 to adjust the minute.

• When you press and hold 4 1/ or

¡ ¢/ while adjusting the minutes, the

minutes digits change continuously.

• If you want to change the hour setting while

adjusting the minutes, press CANCEL.

Finish setting the clock.

To display the clock, press DISPLAY.

• Each time you press the button, the clock and

normal indicator changes alternately.

NOTE

• About one hour after you disconnect the AC

power cord, the set time will be reset.

• If the power supplied using batteries, the clock

does not appear on the display when the unit is

turned off.

Press SLEEP.

Each time you press the button, the shut-off time

(in minute) changes as follows:

10 20 30 60 90 120 OFF \ \ \ \ \ \ \

(back to the beginning)

The unit is now set to turn off after the minutes you

set have elapsed.

If no operation is performed while the Sleep Timer

is set to longer than 30 minutes, the unit turns off

automatically 30 minutes later.

To check the remaining time until the unit shuts

off, press SLEEP once.

To cancel the sleep timer, press SLEEP repeatedly to

select “OFF.”

Using the Daily Timer, you can wake up with your

favorite music.

NOTE

Tune into a station, load a disc, or connect a USB

device/iPod to the unit, and make sure that the

source works properly beforehand.

1. Press CLOCK/TIMER.

2. Press 4 1 ¡ ¢/ or / to adjust the

hour.

• When you press and hold the button,

the hour digit changes continuously.

3. Press SET.

The minutes digits start flashing on the

display.

4. Repeat 2 and 3 to adjust the minute

and select the source, and adjust

volume.

• When you press and hold 4 1/

or / while adjusting the ¡ ¢

minutes, the minutes digits change

continuously.

5. Press to turn off the unit.

• When the on-time comes, the unit sets

the volume gradually to the preset

level.

• The daily timer works only when the

unit is on standby.

To correct a misentry during the process,

press CANCEL.

You can return to the previous step.

To change the set timer info when is

lit, press CLOCK/TIMER twice.

You can start setting from step 2.

Adjusting the volume

You can adjust the volume level between MIN 01

and 30 MAX.

You can program up to 30 tracks from a disc or a

USB device in any desired order including the same

tracks.

NOTE

• You can only make a program when playback is

stopped.

• While making a program, you cannot specify a

group number to select a track.

Load a disc or connect a USB device before

making a program.

See ı Playing back a disc/USB device.

1. Press CD 6 6 or USB .

2. Press 7 to stop playback.

3. Press PLAY MODE to select “PROGRAM.”

4. Press the number buttons to select the track

to program.

5. Repeat step 4 to select other tracks for the

program.

• To cancel the last track in the program, press

CANCEL once.

6. Press CD 6 6 or USB .

Playback starts.

While stopped:

To confirm the programmed tracks, press

/ /4 1 or ¡ ¢ repeatedly; the tracks in the

program will successively appears on the display in

the programmed order.

• To add a track to the end of the program, press

the number buttons to select the track.

To delete the tracks in the program, press CANCEL

repeatedly.

• Each time you press the button, the last track

in the program is erased.

• Turning off the power also clears the program.

To exit from the program play, press PLAY MODE

repeatedly until the “PRGM” indicator goes off.

You can play all the tracks, on the disc or USB device

in random order.

Load a disc or connect a USB device before

random play.

See ı Playing back a disc/USB device.

1. Press CD 6 6 or USB .

2. Press PLAY MODE to select “RANDOM.”

The tracks are played in random order

once.

• The 4 1/ button works only to go back

to the beginning of the current track during

the random playback.

To exit from random mode, press PLAY

MODE. The “RANDOM” indicator goes off.

You can repeat a track or tracks on the disc or

USB device as many times as you like.

Press REPEAT.

Each time you press the button, the play

mode changes as follows:

For CDs:

ALL \ \ canceled \ (back to the beginning)

ALL:

•

Repeats all the tracks on the

disc.

In program mode or

random mode, only ALL

can be selected.

Repeats the current track.

•

For MP3/WMA files:

ALL GROUP \ \ \ canceled \(back to the

beginning)

ALL:

GROUP:

•

Repeats all the tracks on the

disc or USB device.

In program mode or

random mode, only ALL

can be selected.

In normal play mode, repeats

all the tracks in a group.

Repeats the current track.

•

To exit from the repeat mode, press REPEAT

repeatedly until the repeat indicator goes off.

Connect iPod

Disc

USB device

Main unit Remote control

Start Playback

Main unit Remote control

Setting the Clock

Start Playback

Program Playback

Random Playback

Repeat Playback

Main unit Remote control

USB cord

USB

memory

Main unit Remote control

Adjusting the super woofer volume

You can adjust the super woofer volume level

between 1 and 6.

Front door

Open the front door

Dock adaptor

(supplied with iPod

or sold separately)

Connecting other equipment

Microphone/guitar mixing

Using a microphone or a guitar, you can mix its

sound with a source sound.

CAUTION

DO NOT connect a bass guitar to the MIC/GUITAR

INPUT jack, as it may damage the unit.

1. Make sure the MIC/GUITAR selector switch on

the rear of the unit is properly set.

2. Set the MIC/GUITAR LEVEL control to – by

turning it counterclockwise.

3. Connect a microphone or a guitar into the

MIC/GUITAR INPUT jack on the rear of the

unit.

4. Start a source.

5. Adjust the volume and microphone/guitar

levels.

Using Headphones

Be sure to turn down the volume before

connecting or putting on the headphones.

• Connecting the headphones deactivates

the speakers.

• Sound adjustments other than the super

woofer volume level also affect the sound

through the headphones.

NOTE

If iPod is selected as a source, no sound is

heard from headphones.

To turn off the daily timer, press CANCEL.

• While the timer is being set, the timer indicator

( ) lights up.

• While the timer is working, the timer indicator ( )

flashes.

• If you do not operate the unit for more than 1

hour, the unit will turn off.

How to select a number using the remote control

Examples:

To select number 5, press 5.

To select number 15, press +10 then 5.

To select number 20, press +10 once, then 10.

To select number 125, press +100, +10, +10 then 5.

•

Turn on the power at first.

Setting the Sleep Timer

Setting the Daily Timer

Sound mode

Sound modes can be selected to enhance the

type of music being played.

Press SOUND MODE to select the sound

mode.

Each time you press the button, the sound

mode changes as follows:

Sound mode selection:

BEAT: Set to this position for music with a

heavy beat, such as rock and disco

music.

POP: Set to this position for light music

including popular and vocal music.

CLEAR: Set to this position for crisp and clear

sounding music.

FLAT: (no effect): Set to this position not to

apply any sound mode.

Turning o the sound temporarily (Remote

control only)

Press MUTING.

To restore the sound, press MUTING again or

adjust the volume.

Current track

number

Playback

time

Display during playback

Improving the FM reception (Remote

control only)

When an FM stereo (FM) broadcast is hard to

receive or noisy, select the monaural reception

(MONO) mode.

Press FM MODE.

• To restore stereo reception, press FM MODE

again.

Adjusting the antenna

Adjust the FM telescopic antenna’s length,

angle and direction until the best reception is

obtained.

Main unit

3. Press AUDIO IN to select “AUDIO.”

4. Press and hold SET to adjust the source

input level. Each time you press the

button, the input level changes as follows:

LEVEL1 \ LEVEL2 \ LEVEL3 \ (back to the

beginning)

• LEVEL1: Ordinary input level.

• LEVEL2: Increases the input level.

• LEVEL3: Increases the input level more

than “LEVEL2.”

5. Start playback of the external device.

6. Adjust the volume of the unit.

Refer also to the instruction manual for iPod for

details.

Turning o iPod

Press and hold iPod for about 2 seconds.6

• Selecting another source also turns off iPod.

• Turning off the unit may not turn off iPod

depending on the current source.

About the battery charge of iPod

• When the unit is connected to the AC outlet:

The iPod battery is charged if the unit is

turned on.

• When the unit is operated on batteries:

The iPod battery is not charged even if the

unit is turned on.

Each time you press and hold the button, the

indicator changes alternately as follows:

VOUT ON: View video/picture from iPod on

the monitor.

VOUT OFF: View video/picture on iPod.

•

Main unit

CAUTION:

Excessive sound pressure from earphones or

headphones can cause hearing loss.

or or

(On the right)

Main unit

(On the left)

Remote control

Main unit Remote control

DO NOT turn off the unit with the volume

set to an extremely high level; otherwise, the

sudden blast of sound may damage your hearing,

speakers, and headphones when you turn on the

unit or start playback.

Guitar Microphone

Main unit Remote control

Headphones

(not supplied)

Microphone or guitar

(not supplied)

Monitor

(not supplied)

External device

(not supplied)

Composite video cord

(not supplied)

φ 6.3 monaural cable

(not supplied)

Stereo mini plug cord

(not supplied)

Rear of the unit

Product specificaties

Merk:	JVC
Categorie:	Speaker
Model:	RV-NB70S
Kleur van het product:	Zilver
Gewicht:	6800 g
Breedte:	666 mm
Diepte:	240 mm
Hoogte:	231 mm
Gewicht verpakking:	8700 g
Breedte verpakking:	740 mm
Diepte verpakking:	315 mm
Hoogte verpakking:	303 mm
Stroombron:	Batterij/Accu
Ondersteund audioformaat:	MP3, WMA
USB-poort:	Ja
Microfoon, line-in ingang:	Ja
Ingebouwde luidsprekers:	Ja
Gemiddeld vermogen:	40 W
Ondersteund aantal accu's/batterijen:	10
Aantal luidsprekers:	2
Impedantie:	4 Ohm
MP3 afspelen:	Ja
Optische drive type:	CD, CD-R, CD-RW
Ondersteunde frequentiebanden:	FM
Aantal voorkeurszenders:	30
Bass reflex:	Ja
Optical disc player:	Ja
Aantal optische schijven:	1 schijven
Cassette deck:	Nee
Apple docking-compatibiliteit:	iPhone, iPod
Versterker:	Ja
Diameter woofer:	130 mm
Diameter mid-range driver:	80 mm
Afstandsbediening inbegrepen:	Ja
Wifi:	Nee