JennAir JJW2830LL Handleiding

JennAir Fornuis JJW2830LL

Lees hieronder de 📖 handleiding in het Nederlandse voor JennAir JJW2830LL (76 pagina's) in de categorie Fornuis. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/76
FOR SERVICE TECHNICIAN’S USE ONLY
Tech Manual Do not remove or destroy
W11324895A 08/20
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.
DANGER
Electrical Shock Hazard
Only authorized technicians should
perform diagnostic voltage measurements.
After performing voltage measurements,
disconnect power before servicing.
Failure to follow these instructions can
result in death or electrical shock.
Voltage Measurement Safety Information
When performing live voltage measurements, you must do the following:
■ Verify the controls are in the off position so that the appliance does not start when energized.
■ Allow enough space to perform the voltage measurements without obstructions.
■ Keep other people a safe distance away from the appliance to prevent potential injury.
■ Always use the proper testing equipment.
■ After voltage measurements, always disconnect power before servicing.
FOR SERVICE TECHNICIAN’S USE ONLY
2
IMPORTANT: Electrostatic Discharge (ESD) Sensitive Electronics
ESD problems are present erywhere ESD may damage or weaken the electronic control assemblyev . . The new control
assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress.
■ Use an antistatic wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the
appliance
-OR-
Touch your finger repeatedly to a green ground connection point or unpainted metal in the appliance.
■ Before removing the part from its package, touch the antistatic bag to a green ground connection point or
unpainted metal in the appliance.
■ Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.
■ When repackaging failed electronic control assembly in antistatic bag, observe above instructions.
3
Diagnostics
Unplug oven or disconnect power before performing the following checks:
■A potential cause of a control not functioning is corrosion on connections.
Observe connections andcheck for continuity with an ohmmeter.
■All tests/checks should be made with a VOM or DVM having a sensitivity
of 20,000 Ω per volt DC or greater.
■Check all connections before replacing components, looking for broken
or loose wires, failed terminals, or wires not pressed into connectors far
enough. Damaged harness must be entirely replaced. Do not rework a
harness.
■Resistance checks must be made with power cord unplugged from outlet
and with wiring harness or connectors disconnected.
■If the oven does not heat, there may be a problem with connections to
the power supply. Check the connection to L2.
IMPORTANT: Do not replace the control if there is no evidence of any failure.
To Enter Diagnostics Mode:
Before proceeding with any corrective action, perform the following steps to
enter the Diagnostics mode:
1. Enter Diagnostics mode by pressing the same 3 keypads 3 times in a row.
Single Ovens: Press KITCHEN TIMER>TOOLS> SELF CLEAN (repeat 2
more times).
Double Ovens: Press UPPER OVEN>LOWER OVEN>LOWER LIGHT
(repeat 2 more times).
NOTE: You do not need to wait for any audible or visual feedback from the
control between keypad presses.
2. If control does not enter Diagnostics mode, continue repeating the keypad
sequence from Step 1. All the keypads will light up when the control enters
Diagnostics mode.
3. From the Diagnostics menu, scroll to the desired selection using the
touch screen.
Error Diagnostics: View and clear the failure history.
Component Activation: Manually activate each relay.
Sensors & Switches: View the traditional oven cavity temperatures and
door/latch switch status.
System Information: View the model number, serial number, and
software versions.
Exit Diagnostics
General Procedure: Error Codes
NOTE: All failures are stored in the failure history. To check if the error code
is still present, start a cooking function and wait 1 minute to check if the error
appears.
1. Enter Diagnostics mode.
2. Touch or scroll to “Error Diagnostics” in the Diagnostics menu, and then
touch “OK.”
3. To clear error codes, touch “Clear History.”
4. If no failures are listed, the message “No Error” willappear on the screen.
General Procedure: Software Version
For Engineering only

Product specificaties

Merk: JennAir
Categorie: Fornuis
Model: JJW2830LL

Heb je hulp nodig?

Als je hulp nodig hebt met JennAir JJW2830LL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Fornuis JennAir

JennAir

JennAir JGCK424PS Handleiding

11 April 2024
JennAir

JennAir JIS1450ML Handleiding

22 Augustus 2023
JennAir

JennAir JDS1750EB Handleiding

6 Juli 2023
JennAir

JennAir JED4430KS Handleiding

4 Juli 2023
JennAir

JennAir JDRP436HL Handleiding

4 Juli 2023
JennAir

JennAir JDRP430HM Handleiding

27 Juni 2023
JennAir

JennAir JGRP636HL Handleiding

24 Juni 2023
JennAir

JennAir JEC4430KS Handleiding

22 Juni 2023
JennAir

JennAir JEC4430BB Handleiding

21 Juni 2023
JennAir

JennAir JIC4724HB Handleiding

21 Juni 2023

Handleiding Fornuis

Nieuwste handleidingen voor Fornuis

Whirlpool

Whirlpool TGML 660 NB Handleiding

3 December 2024
Whirlpool

Whirlpool WB S0060 NE Handleiding

3 December 2024
Whirlpool

Whirlpool WS68M8CCW Handleiding

3 December 2024
Whirlpool

Whirlpool WS68V8KCW Handleiding

3 December 2024
Whirlpool

Whirlpool GOWL 928/NB Handleiding

3 December 2024
Whirlpool

Whirlpool WS68G8ACXT/E Handleiding

3 December 2024
Whirlpool

Whirlpool WSQ1160NE Handleiding

3 December 2024
Whirlpool

Whirlpool OMR58CU1B Handleiding

3 December 2024
Whirlpool

Whirlpool WBB3760BF Handleiding

3 December 2024
Whirlpool

Whirlpool GOR 625/NB Handleiding

3 December 2024