JBL Control 50 Handleiding

JBL Speaker Control 50

Lees hieronder de 📖 handleiding in het Nederlandse voor JBL Control 50 (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 87 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Control Contractor 50 Series

Control 50S/T and Control 52

Surface-Mount

Subwoofer-Satellite

Loudspeaker System

Key Features:

䉴

Stylish, unobtrusive design ﬁts

into a wide variety of decors

䉴

High ﬁdelity sound

䉴

Selectable 70V/100V for

distributed lines, or low

impedance

䉴

Versatility for either two or four

satellite speakers per system

䉴

Ability to mix and match with

Control Contractor40 Series in-

ceiling models

䉴

Wall-mount brackets included

䉴

Available in black or white

The Control 50 Series

subwoofer-satellite loudspeaker

system provides high ﬁdelity

sound in restaurants, retail stores,

music cafes, health clubs, theme

bars, leisure venues, or any

location where full-range high

ﬁdelity foreground/background

music is required from surface-

mount system.

Control 52 Satellite Speaker

The stylish Control 52 satellite

loudspeaker produces superb

high ﬁdelity sound via a low-

distortion 60 mm (2 in) driver,½

which features a secondary

bucking magnet for high

efﬁciency, rubber half roll

surround for enhanced bass

performance, 19 mm (0.75 in)

copper clad aluminum wire voice

coil on a vented Nomex®former

for high ﬁdelity and reliability,

and a copper-capped pole piece

for more consistent impedance

and extended high frequency

response. The wall bracket allows

each speaker to be angled up to

45° off-axis.

Control 50 Subwoofer

The 150 Watt (600 Watt peak) Control 50S/T subwoofer contains a

high-power, long-excursion, 200 mm (8 inch) driver which features

an extremely robust high-mass cone for extended low frequency

response, a 38 mm (1.5 in) 4-layer copper voice coil for high motor

strength, an aluminum former for good transient response, and a

rubber half roll surround for enhanced bass performance. The

Control 50S/T’s included two-piece easy-mount wall-bracket installs

quickly: The multi-point wall portion of the bracket attached to the

wall and the self-guiding speaker-mounted bracket drops into place

for a secure attachment. A cover over the Control 50S/T terminal cup

keeps wiring neat. The Control 50S/T is mono. The crossover

network built into the subwoofer provides proper signal routing and

four satellite output connectors allow connection of the wires for the

four Control 52 satellite loudspeakers. A Loop Out connector is also

provided on the subwoofer for looping the full-range input signal to

other loudspeakers or to other subwoofer/satellite systems.

System Conﬁguration

Available as packaged system or as separate items, the Control 50

Series is extremely versatile system. The C50PACK system contains

four Control 52 satellite speakers and one Control 50S/T subwoofer

as an easy predesigned system. For smaller ﬂoor spaces, the Control

50S/T subwoofer can be utilized with two Control 52 satellite

speakers. The Control 50 system is mono. Both the Control 50S/T

and Control 52 can be intermixed in systems along with the Control

40 Series in-ceiling models – Control 40CS/T subwoofer and Control

42 satellite speaker – to match the form factor requirements of a

wide variety of applications.

Professional Series

䉴Control 50S/T and Control 52 Surface-Mount Subwoofer-Satellite Loudspeaker System

Control 50 Subwoofer-Satellite System Speciﬁcations

Frequency Range (-10 dB)1: 32 Hz – 20 kHz

Frequency Response (±3 dB)1: 50 Hz – 17 kHz

Power Capacity2: 200 Watts Continuous Program Power (100 hrs)

100 Watts Continuous Pink Noise (100 hrs)

Nominal Sensitivity (2.83V, 1m)1: 87 dB with 4 satellites

85 dB with 2 satellites

(subwoofer center of wall, higher sensitivity depending on subwoofer boundary loading, see application note)

Nominal Impedance: 4 ohms (in bypass/thru mode) with 4 satellites

8 ohms (in bypass/thru mode) with 2 satellites

Transformer Taps: 80W, 40W, 20W, (& 10W @ 70V), plus bypass/thru (listed as 8⍀on switch to indicate subwoofer impedance)

Control 50S/T Speciﬁcations

Frequency Range (-10 dB)1: 32 Hz – 200 Hz

Frequency Response (±3 dB)1: 50 Hz – 150 Hz

Power Capacity2: 300 Watts Continuous Program Power (2 hrs)

150 Watts Continuous Pink Noise (2 hrs)

200 Watts Continuous Program Power (100 hrs)

100 Watts Continuous Pink Noise (100 hrs)

Nominal Sensitivity (2.83V, 1m)1: 95 dB (near corner), 89 dB (center of wall)

Rated Maximum SPL (1m): 115 dB average, 121 dB peak (near corner)

109 dB average, 115 dB peak (center of wall)

Nominal Impedance: 8 ohms (in bypass/thru mode)

Transformer Taps: 80W, 40W, 20W, (& 10W @ 70V), 8 ohm bypass/thru

Transducer:

Driver: 200 mm (8 in) with polypropylene cone, butyl rubber surround, 38 mm (1.5 in) 4-layer copper-clad coil, vented aluminum

former

Enclosure:

Input Connectors: Six removable locking 2-pin connectors with screw-down terminals. Max wire 12 AWG (2.5 mm

Material: Top, bottom, front & bottom: Structural plywood. Port & terminal panels: MDF. Grille: Painted zinc-plated metal.

Dimensions (H x W x D): Cabinet: 356 x 391 x 203 mm (14.0 x 15.4 x 8.0 in)

Wall Bracket: 15 mm (0.6 in) deep

Wall Bracket: 2.3 mm (0.9 in) thick zinc-plated and painted cold-rolled steel

Net Weight: 9.0 kg (20 lbs)

Shipping Weight: 10.2 kg (23 lbs)

Included Accessories: Wall bracket (both speaker and wall parts) with 4 pcs M6 screws to attach to speaker, terminal cover, 6 pcs 2-pin locking

connectors, M6 screw for safety lanyard attachment.

Control 52 Speciﬁcations

Frequency Range (-10 dB)1: 140 Hz – 20 kHz

Frequency Response (±3 dB)1: 180 Hz – 17 kHz

Power Capacity2: 50 Watts Continuous Program Power (2 hrs)

25 Watts Continuous Pink Noise (2 hrs)

30 Watts Continuous Program Power (100 hrs)

15 Watts Continuous Pink Noise (100 hrs)

Nominal Sensitivity1: 85 dB (4.0V/1m = 1W)

82 dB (2.83V, 1m)

Nominal Coverage Angle

3: 150° x 150° (omnidirectional)

Rated Maximum SPL (1m): 94 dB average, 100 dB peak

Nominal Impedance: 16 ohms

Transducer:

Driver: 60 mm (2.5 in) with polypropylene cone, butyl rubber surround, 19 mm (0.75 in) copper-clad coil, vented Nomex

®former,

secondary bucking magnet, and copper sleeved pole piece for high frequency extension.

Enclosure:

Input Connector: Removable locking 2-pin connector with screw-down terminals. Max wire 12 AWG (2.5 mm

Material: High impact polystyrene, painted zinc-plated metal grille.

Dimensions (H x W x D): Cabinet: 115 x 84 x 96 mm (4.5 x 3.3 x 3.75 in)

Wall bracket: 51 mm (2.0 in)

Net Weight: 0.7 kg (1.5 lbs)

Shipping Weight: 0.8 kg (1.8 lbs)

Included Accessories: Wall bracket (both speaker and wall parts), 2-pin locking connector.

1Half-space (mounted on wall).

2Continuous Pink noise rating is IEC-shaped pink noise with a 6 dB crest factor for 100 hours continuously. Continuous Program Power is a conservative expression of the system’s ability to

handle normal speech and music program material, and is deﬁned as 3 dB above the Continuous Pink Noise rating.

3Half-space, average 1 kHz – 4 kHz

JBL continually engages in research related to product improvement. Changes introduced into existing products without notice are an expression of that philosophy.