JBL Balboa 10 Handleiding

JBL Speaker Balboa 10

Lees hieronder de 📖 handleiding in het Nederlandse voor JBL Balboa 10 (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

BALBOA 10, BALBOA 30

AND BALBOA CENTER

BALBOA SERIES

OWNER’S GUIDE

MODEL: BALBOA 10

SPEAKER PLACEMENT

Proper placement of the

speakers is an important step

in obtaining the most realistic

soundstage possible. These

recommendations are for the

optimal placement of the

loudspeakers. Use these

placement recommendations

as a guide. Slight variations

will not diminish your listen-

ing pleasure.

All of the Balboa Series loud-

speakers referred to in this

guide are video-shielded

and can safely be placed

near a television.

As front speakers

MODEL: BALBOA 30

As surround speakers

MODEL: BALBOA CENTER

The Balboa Center loud-

speaker is designed to com-

plement all of the Balboa

Series loudspeakers. It is the

ideal way to re-create the

cinematic experience in your

home.

†Placement for surround back

speakers in 6.1/7.1 systems,

or alternate placement for

side surround speakers in 5.1

systems.

MODELS:

BALBOA 10 AND

BALBOA CENTER

The supplied self-adhesive

rubber feet may be attached

to the bottom corners of your

speakers to protect your

furniture.

MODEL: BALBOA 30

This model is shipped with

four self-adhesive nonskid

pads that are to be used when

the loudspeaker is intended

to be placed on a smooth-

surfaced floor, such as tile or

hardwood. Gently lay the

speaker on its side (not its

front or back) on a soft,

nonabrasive surface. Attach

each pad to the bottom of its

foot in the widest portion of

the recessed area.

DO NOT attach the pads if

the speaker will be placed

on carpeting.

NEVER drag the speaker to

move it, as this will damage

the pads, the feet and/or the

wood cabinet itself. Always

lift the speaker and carry it to

its new location.

CAUTION: Floorstanding

(tower) loudspeakers have a

high center of gravity and may

become unstable and tip over

during earthquakes, or if

rocked, tipped or improperly

positioned. If this is a concern,

these speakers should be

anchored to the wall behind

them, using the same proce-

dures and hardware custom-

ary for anchoring bookcases

and wall units. The customer

is responsible for proper instal-

lation and proper selection of

hardware.

Without pad With pad

Place pads here

SPEAKER PLACEMENT (CONTINUED)

MODELS:

BALBOA 10 AND

BALBOA 30

MODEL:

BALBOA CENTER

Speakers and electronics

terminals have correspon-

ding (+) and (–) terminals. It

is important to connect both

speakers identically: (+) on

the speaker to (+) on the

amplifier and (–) on the

speaker to (–) on the ampli-

fier. Wiring “out of phase”

results in thin sound, weak

bass and poor imaging. With

the advent of multichannel

surround sound systems,

connecting all of the speak-

ers in your system with the

correct polarity remains

equally important in order to

preserve the proper ambi-

ence and directionality of the

program material.

To use the binding-post

speaker terminals, unscrew

the colored collar until the

pass-through hole in the cen-

ter post is visible. Insert the

bare end of the wire through

this hole; then screw the col-

lar down until the connection

is tight.

The hole in the center of

each collar is intended for

use with banana-type con-

nectors. To comply with

European CE certification,

these holes are blocked with

plastic inserts at the point of

manufacture. Use of banana-

type connectors requires the

removal of the inserts. Do

not remove these inserts if

you are using the product

in an area covered by the

European CE certification.

Receiver

Speaker Outputs

– +

CENTER

– +

– +– +

– +

Receiver’s Speaker Outputs

LEFT

RIGHT

– +

SPEAKER CONNECTIONS

TROUBLESHOOTING

If there is no sound from

any of the speakers:

• Check that receiver/ampli-

fier is on and that a source is

playing.

• Review proper operation of

your receiver/amplifier.

If there is no sound com-

ing from one speaker:

• Check the “Balance”

control on your receiver/

amplifier.

• Check all wires and connec-

tions between receiver/

amplifier and speakers.

• Make sure no wires are

touching other wires or

terminals and creating a

short circuit.

• Make sure all wires are

connected. Make sure none

of the speaker wires are

frayed, cut or punctured.

• In Dolby* Digital or DTS®

modes, make sure that the

receiver/processor is config-

ured so that the speaker in

question is enabled.

• Turn off all electronics and

switch the speaker in ques-

tion with one of the other

speakers that is working cor-

rectly. Turn everything back

on, and determine whether

the problem has followed the

speaker, or has remained in

the same channel. If the

problem is in the same chan-

nel, the source of the prob-

lem is most likely with your

receiver or amplifier, and

you

should consult the owner’s

manual for that product for

further information.

If the

problem has followed the

speaker, consult your dealer

for further assistance or, if

that is not possible, visit

www.jbl.com for further

information.

If the system plays at

low volumes but shuts

off as volume is

increased:

• Check all wires and connec-

tions between receiver/

amplifier and speakers.

• Make sure all wires are

connected. Make sure none

of the speaker wires are

frayed, cut or punctured.

• If more than one pair of

main speakers is being used,

check the minimum imped-

ance requirements of your

receiver/amplifier.

If there is no (or low)

bass output:

• Make sure the polarities

(+ and –) of the left and right

“Speaker Inputs” are

connected properly.

• If your system includes a

powered subwoofer, make

sure it is connected correctly,

plugged into an active AC

outlet and turned on. See the

owner's guide for your sub-

woofer for more information.

• If your system does not

include a powered sub-

woofer, consider adding one

for use with digital “.1” sur-

round formats.

If there is no sound from

the surround speakers:

• Check all wires and con-

nections between receiver/

amplifier and speakers. Make

sure all wires are connected.

Make sure none of the

speaker wires are frayed,

cut or punctured.

• Review proper operation of

your receiver/amplifier and

its surround sound features.

• Make sure the movie or TV

show you are watching is

recorded in a surround sound

mode. If it is not, check to

see whether your receiver/

amplifier has other surround

modes you may use.

• In Dolby Digital or DTS

modes, make sure your

receiver/processor is config-

ured so that the surround

speakers are enabled.

• If you are using both side

surround and back surround

speakers, make sure that your

receiver/processor is config-

ured for 6.1/7.1 operation.

• Review the operation of your

DVD player and the jacket of

your DVD to make sure that

the DVD features the desired

Dolby Digital or DTS mode,

and that you have properly

selected that mode using both

the DVD player’s menu and the

DVD disc’s menu.

Declaration of Conformity

We, Harman Consumer Group International

2, route de Tours

72500 Chateau-du-Loir

France

declare in own responsibility that the products

described in this owner’s manual are in compliance

with technical standards:

EN 61000-6-3:2001

EN 61000-6-1:2001

Gary Mardell

Harman Consumer Group International

Chateau-du-Loir, France 1/05

Product specificaties

Merk:	JBL
Categorie:	Speaker
Model:	Balboa 10
Gewicht:	3900 g
Gemiddeld vermogen:	125 W
Impedantie:	8 Ohm
Peak Music Power Output (PMPO):	240 W
Frequentiebereik:	68 - 20 Hz
Gevoeligheid:	86 dB
Afmetingen (B x D x H):	259 x 165 x 210 mm
Crossover frequentie:	3000 Hz