Jamo WA-2 Handleiding

Jamo Subwoofer WA-2

Lees hieronder de 📖 handleiding in het Nederlandse voor Jamo WA-2 (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

WA-2

Owner's Manual

IMPORTANT SAFETY INSTRUCTIONS!

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wider blade or the third prong are provided for your safety. If the provided plug does not ﬁt

into your outlet, consult an electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories speciﬁed by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14. REFER all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

15. DO NOT expose this apparatus to dripping or splashing and ensure that no objects ﬁlled with liquids,

such as vases, are placed on the apparatus.

16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug

from the AC receptacle.

17. The mains plug of the power supply cord shall remain readily operable.

The exclamation point, within an equilateral triangle, is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the product.

The lightning ﬂash with arrowhead symbol within an equilateral triangle, is intended to

alert the user to the presence of uninsulated “dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to constitute a risk of electrical shock to

persons.

WARNING: To reduce the risk of ﬁre or electrical shock, do not expose this apparatus to rain or moisture.

WARNING: No naked ﬂame sources – such as candles – should be placed on the product.

Place the equipment near a main power supply outlet and make sure that you can easily access

the power breaker switch.

WARNING: This product is intended to be operated ONLY from the AC Voltages listed on the back panel

or included power supply of the product. Operation from other voltages other than those indicated may

cause irreversible damage to the product and void the products warranty. The use of AC Plug Adapters

is cautioned because it can allow the product to be plugged into voltages in which the product was

not designed to operate. If the product is equipped with a detachable power cord, use only the type

provided with your product or by your local distributor and/or retailer. If you are unsure of the correct

operational voltage, please contact your local distributor and/or retailer.

FCC AND CANADA EMC COMPLIANCE INFORMATION:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Approved under the veriﬁcation provision of FCC Part 15 as a Class B Digital Device.

Caution: Changes or modiﬁcations not expressly approved by the manufacturer could void the user’s

authority to operate this device.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

EU COMPLIANCE INFORMATION:

Eligible to bear the CE mark, Conforms to European Union Low Voltage Directive 2006/95/EC;

Conforms to European Union EMC Directive 2004/108/EC.

WEEE NOTICE

Note: This mark applies only to countries within the European Union (EU) and Norway.

This appliance is labeled in accordance with European Directive 2002/96/EC concerning

waste electrical and electronic equipment (WEEE). This label indicates that this product

should not be disposed of with household waste. It should be deposited at an appropriate

facility to enable recovery and recycling.

WIRELESS TRANSMITTER COMPLIANCE INFORMATION:

The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry Canada technical

speciﬁcations were met. This equipment complies with FCC and IC radiation exposure limits set forth for

an uncontrolled environment. This equipment should be installed and operated with minimum distance

20cm between the radiator and your body. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Le terme «IC:» avant le numéro de certiﬁcation radio signiﬁe seulement que les spéciﬁcations

techniques d’Industrie Canada ont été respectées.

Cet appareil est conforme à FCC et IC l’exposition aux rayonnements limites ﬁxées pour un envi-

ronnement non contrôlé. Cet appareil doit être installé et utilisé avec une distance minimale de 20 cm

entre le radiateur et votre corps. Cet transmetteur ne doit pas être co-situé ou opérant en liaison avec

toute autre antenne ou transmetteur.

This device has been designed to operate with the antennas listed below, and having a maximum gain of

[x] dB. Antennas not included in this list or having a gain greater than [x] dB are strictly prohibited for

use with this device. The required antenna impedance is 50 ohms.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired operation of

the device.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen

that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful

communication.

Thank you for your purchase of the Klipsch WA-2 Wireless Subwoofer Kit!

The WA-2 will only operate with select Klipsch, Energy, Mirage and Jamo brand subwoofers that have

a “WA Port” input. The WA-2 is a 2.4 GHz product designed to wirelessly transmit a signal up to a 50

foot radius.

Packing List:

1. Transmitter

2. Receiver

3. Power supply

4. Audio cable

5. Velcro strips

6. This Owner’s Manual

Setup:

1. Decide where the subwoofer will go (refer to your subwoofer owner’s manual).

2. Most receivers (and pre-ampliﬁers) have a line level subwoofer output labeled Subwoofer Pre Out,

Sub Out, SW Out, etc. If you have this, connect one end of the supplied audio cable to it and connect

the other end of the cable into WA-2 transmitter input ‘C’ . In absence of a subwoofer output connect

Left and Right channel Pre-Amp outputs from your receiver (if provided) to ‘C’ and ‘B’ inputs on the

transmitter.

3. Connect the cable from the WA-2 receiver to the “WA Port” on the back of the

subwoofer. Carefully match the 4 pins of the cable to the corresponding 4 holes on the

WA Port and gently push in until connected. Improper pin alignment can result in damage

to the connector.

4. Plug supplied power supply cable into ‘E’ on the WA-2 transmitter and plug other end into an AC wall

outlet.

C A U T I O N

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this

equipment are hazardous to life. No user-serviceable parts inside. Refer

all servicing to qualified service personnel.

5. Check to make sure Gain Switch ‘A’ is in middle position (0dB). This position best matches the

output voltage of most receivers and processors.

6. Turn receiver/pre-ampliﬁer on.

7. Turn subwoofer to “On” or “Auto On” position.

8. The WA-2 transmitter and receiver should be automatically “paired”with their red LED’s ‘D’ on

solid and the subwoofer should now be operational.

9. You can use the supplied Velcro strips to attach the WA-2 receiver to the back of the subwoofer.

Some subwoofers have two screws on back that the receiver attaches to.

TROUBLESHOOTING:

- If the subwoofer does not operate and the red LED’s ‘D’ are ﬂashing on the WA-2 transmitter and

receiver, a simple “pairing” is needed. Push and hold in button ‘F’ on the transmitter while pushing

and holding button ‘G’ on the receiver and keep pushed until both LED’s stop ﬂashing and glow solid

(approximately 5 seconds).

- Since the WA-2 is a wireless device it may encounter RF interference from other wireless

devices in the same area. If there is difﬁculty “pairing” the transmitter and receiver, or their signal

connection “fades”, you may need to move them closer together and/or farther away from other

“wireless” products.

- If you do not get a signal, or get a low signal level from the subwoofer, make sure the subwoofer

out level control on your surround receiver is set correctly (usually at the halfway point sometimes

labeled “0dB”). If your subwoofer out level on your surround receiver is correct, and you have

adjusted the subwoofer volume level and the signal is still too low, move the gain control ‘A’ to the

right (+12dB) to increase the signal to the subwoofer. If the signal is too high, move the gain control

to the left (-12dB) to reduce signal strength.

Product specificaties

Merk:	Jamo
Categorie:	Subwoofer
Model:	WA-2

Heb je hulp nodig?

Als je hulp nodig hebt met Jamo WA-2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Subwoofer Jamo

Jamo S 808 SUB Handleiding

24 Juni 2023

Jamo Concert II C912 Handleiding

21 Juni 2023

Jamo S 808 Handleiding

21 Juni 2023

Jamo SUB 260 Handleiding

15 Juni 2023

Jamo C 80 SUB Handleiding

14 Juni 2023

Jamo SUB 210 Handleiding

13 Juni 2023

Jamo SUB 250 Handleiding

13 Juni 2023

Jamo J 112 SUB Handleiding

13 Juni 2023

Jamo SUB 800 Handleiding

12 Juni 2023

Jamo J 12 SUB Handleiding

11 Juni 2023

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

Deaf Bonce Apocalypse ASA-4000.1 Handleiding

20 November 2024

Deaf Bonce Apocalypse Atom 2000 PRO Handleiding

20 November 2024

JBL PSW-D115 Handleiding

20 November 2024

JBL PSW-D110 Handleiding

20 November 2024

JBL PSW-D112 Handleiding

20 November 2024

JBL Power P1224 Handleiding

20 November 2024

JBL Power P1220D II Handleiding

20 November 2024

JBL Power P1242 Handleiding

20 November 2024

JBL Power P1220 II Handleiding

20 November 2024

JBL Power P1020 II Handleiding

20 November 2024